commit 85ff3c29d7 ("ASoC: samsung: Rename DMA platform registration
functions") renames the DMA registration functions. Fix the places where
it was left out.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have to disable the ssi irq, as it is not safe for all platforms to
write back into the status register. It also runs into non-linefetch
aborts.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
imx-pcm-fiq is checking for TE RE bits, so enable them only if
necessary.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip errata for the i.MX35, Rev.2 has the following errata:
ENGcm06222: SSI:Transmission does not take place in bit length early frame sync
configuration
The workaround states, that TX_EN and SSI_EN bits should be set in the same
register write. As the next errata in the document (ENGcm06532) says to always
write RX_EN and TX_EN in the same register write in network mode.
Therefore include the whole write to
CCSR_SSI_SCR_TE and CCSR_SSI_SCR_RE
into the write to
CCSR_SSI_SCR_SSIEN
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds ac97-slave support.
For ac97, the registers have to be setup earlier than for other ssi
modes because there is some communication with the external device
before streaming. So this patch introduces a fsl_ssi_setup function to
setup the registers for different ssi operation modes seperately.
This patch was tested with imx27-pca100.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixing warning message:
sound/pci/rme96.c: In function ‘snd_rme96_resume’:
sound/pci/rme96.c:2418:19: warning: ignoring return value of ‘pci_enable_device’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone automute on this machine triggers annoying pop noises.
It seems that only the first DAC can be used, the secondary DAC always
results in this problem. This patch disables the secondary DAC with
a few additional workarounds.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed ALC283 D3 to D0 and D0 to D3 Headphone pop noise.
The previous fix [c5177c86: ALSA: hda - Fix the noise after suspend on
ALC283 codec] doesn't work sufficiently for some laptops.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without proper power management handling, the first use
of a Digi96/8 anytime after a suspend / resume cycle will
start playback with distortions.
v3: Abort if vmalloc() of suspend buffers fail, but do not
leak memory in that case.
[fixed wrong memory leak fix again -- tiwai]
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch implements a device-tree-only CPU DAI driver for Freescale
S/PDIF controller that supports stereo playback and record feature.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes a regression exposed during the merge window by commit
9f310de "ARM: tegra: fix VBUS regulator GPIO polarity in DT"; namely that
USB VBUS doesn't get turned on, so USB devices are not detected. This
affects the internal USB port on TrimSlice (i.e. the USB->SATA bridge, to
which the SSD is connected) and the external port(s) on Seaboard/
Springbank and Whistler.
The Tegra DT as written in v3.11 allows two paths to enable USB VBUS:
1) Via the legacy DT binding for the USB controller; it can directly
acquire a VBUS GPIO and activate it.
2) Via a regulator for VBUS, which is referenced by the new DT binding
for the USB controller.
Those two methods both use the same GPIO, and hence whichever of the
USB controller and regulator gets probed first ends up owning the GPIO.
In practice, the USB driver only supports path (1) above, since the
patches to support the new USB binding are not present until v3.12:-(
In practice, the regulator ends up being probed first and owning the
GPIO. Since nothing enables the regulator (the USB driver code is not
yet present), the regulator ends up being turned off. This originally
caused no problem, because the polarity in the regulator definition was
incorrect, so attempting to turn off the regulator actually turned it
on, and everything worked:-(
However, when testing the new USB driver code in v3.12, I noticed the
incorrect polarity and fixed it in commit 9f310de "ARM: tegra: fix VBUS
regulator GPIO polarity in DT". In the context of v3.11, this patch then
caused the USB VBUS to actually turn off, which broke USB ports with VBUS
control. I got this patch included in v3.11-rc1 since it fixed a bug in
device tree (incorrect polarity specification), and hence was suitable to
be included early in the rc series. I evidently did not test the patch at
all, or correctly, in the context of v3.11, and hence did not notice the
issue that I have explained above:-(
Fix this by making the USB VBUS regulators always enabled. This way, if
the regulator owns the GPIO, it will always be turned on, even if there
is no USB driver code to request the regulator be turned on. Even
ignoring this bug, this is a reasonable way to configure the HW anyway.
If this patch is applied to v3.11, it will cause a couple pretty trivial
conflicts in tegra20-{trimslice,seaboard}.dts when creating v3.12, since
the context right above the added lines changed in patches destined for
v3.12.
Reported-by: Kyle McMartin <kmcmarti@redhat.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
As Sergei Shtylyov explained in the #mipslinux IRC channel:
[Mon 2013-08-19 12:28:21 PM PDT] <headless> guys, are you sure it's not "DMA off stack" case?
[Mon 2013-08-19 12:28:35 PM PDT] <headless> it's a known stack corruptor on non-coherent arches
[Mon 2013-08-19 12:31:48 PM PDT] <DonkeyHotei> headless: for usb/ehci?
[Mon 2013-08-19 12:34:11 PM PDT] <DonkeyHotei> headless: explain
[Mon 2013-08-19 12:35:38 PM PDT] <headless> usb_control_msg() (or other such func) should not use buffer on stack. DMA from/to stack is prohibited
[Mon 2013-08-19 12:35:58 PM PDT] <headless> and EHCI uses DMA on control xfers (as well as all the others)
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to get an interface specification if we know it's the
wrong one.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Already existing property flags are filled wrong for properties created from
initial FDT. This could cause problems if this DYNAMIC device-tree functions
are used later, i.e. properties are attached/detached/replaced. Simply dumping
flags from the running system show, that some initial static (not allocated via
kzmalloc()) nodes are marked as dynamic.
I putted some debug extensions to property_proc_show(..) :
..
+ if (OF_IS_DYNAMIC(pp))
+ pr_err("DEBUG: xxx : OF_IS_DYNAMIC\n");
+ if (OF_IS_DETACHED(pp))
+ pr_err("DEBUG: xxx : OF_IS_DETACHED\n");
when you operate on the nodes (e.g.: ~$ cat /proc/device-tree/*some_node*) you
will see that those flags are filled wrong, basically in most cases it will dump
a DYNAMIC or DETACHED status, which is in not true.
(BTW. this OF_IS_DETACHED is a own define for debug purposes which which just
make a test_bit(OF_DETACHED, &x->_flags)
If nodes are dynamic kernel is allowed to kfree() them. But it will crash
attempting to do so on the nodes from FDT -- they are not allocated via
kzmalloc().
Signed-off-by: Wladislav Wiebe <wladislav.kw@gmail.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Some Poulsbo cards seem to incorrectly report SDVO_CMD_STATUS_TARGET_NOT_SPECIFIED instead of SDVO_CMD_STATUS_PENDING, which causes the display to be turned off.
Signed-off-by: Guillaume Clement <gclement@baobob.org>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- On ARM did not have balanced calls to get/put_cpu.
- Fix to make tboot + Xen + Linux correctly.
- Fix events VCPU binding issues.
- Fix a vCPU online race where IPIs are sent to not-yet-online vCPU.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSFMaJAAoJEFjIrFwIi8fJ+/0H/32rLj60FpKXcPDCvID+9p8T
XDGnFNttsxyhuzEzetOAd0aLKYKGnUaTDZBHfgSNipGCxjMLYgz84phRmHAYEj8u
kai1Ag1WjhZilCmImzFvdHFiUwtvKwkeBIL/cZtKr1BetpnuuFsoVnwbH9FVjMpr
TCg6sUwFq7xRyD1azo/cTLZFeiUqq0aQLw8J72YaapdS3SztHPeDHXlPpmLUdb6+
hiSYveJMYp2V0SW8g8eLKDJxVr2QdPEfl9WpBzpLlLK8GrNw8BEU6hSOSLzxB7z/
hDATAuZ5iHiIEi1uGfVjOyDws2ngUhmBKUH5x5iVIZd2P5c/ffLh2ePDVWGO5RI=
=yMuS
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.11-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- On ARM did not have balanced calls to get/put_cpu.
- Fix to make tboot + Xen + Linux correctly.
- Fix events VCPU binding issues.
- Fix a vCPU online race where IPIs are sent to not-yet-online vCPU.
* tag 'stable/for-linus-3.11-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/smp: initialize IPI vectors before marking CPU online
xen/events: mask events when changing their VCPU binding
xen/events: initialize local per-cpu mask for all possible events
x86/xen: do not identity map UNUSABLE regions in the machine E820
xen/arm: missing put_cpu in xen_percpu_init
Pull MIPS fix from Ralf Baechle:
"Just a single patch which fixes a special case in the MIPS FPU
emulator which is always required, even on CPUs with FPU. There is
the rare special case that an FPU (or certain other instructions) in a
branch delay slot is causing an exception and then the branch
instruction will need to be emulated by the kernel before resuming
execution. This is working great except if the branch instruction is
an Octeon BBIT instruction.
The boring disclaimer - all MIPS defconfigs build tested and no
regressions and runtime tested on Octeon, no known issues"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Handle OCTEON BBIT instructions in FPU emulator.
(discovered with Vince's fuzzing tool).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=Lajp
-----END PGP SIGNATURE-----
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 perf fixes from Catalin Marinas:
"Perf backend fixes for arm64 where the user can cause kernel panic
(discovered with Vince's fuzzing tool)"
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: perf: fix event validation for software group leaders
arm64: perf: fix array out of bounds access in armpmu_map_hw_event()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJSEoS0AAoJEBvWZb6bTYbyE/8P/izUr1XtKBqtVuqVBMewEkeB
SBgvJ2w681f4d+1waVAEPqWVGKHDvSOQC54sG6Y3fWHKijKGLiQhLaY3Y1WaLlO1
B+duREwCwHaApjrpYoKhkyGQVpgyIfHBVe8d2TM9Q2bRuYNZEEcOtfdXk+Qfr6WR
2kN+67ivJzAXvjs0uuRyJtXXq9cemcOnngsAfBlJz+j6UbiEdQ3l569D3wQU1jS2
lUxxCEdtBDKDXkJUbTYvtJNYR48caqVXhYBTjpmY04207iSHmacUytOXO3rRA3OL
fFhm/QeKVZND0XrJDUOMFzosWdUVdP5Qd5PtYoV/gEydNJMMpPs+dFKv+RXzrWlm
2S2PWbFlkFT8yM+xwh6uKnLQ1aj614dkK2vKlp9GwDuwWiaod71C8ouTJvanNHGt
pWgktFlfD+npSc3QDeXG5QB78pTSeyJfZBeVvA+U/etX+vjdfFWZ3bHMScrAE4DX
xsdvtfamo0m9v2yZsnKzRWtCQq9No5FRb/c31w7yUzSXNBtyNR0Vft9gmiLo4HYa
FQ0wC2UPyaKbfYtX0orpWnN3u4vaylGw2HuzK+2Mwi2HL+AMI6Piu//nrTbqb/i+
1a6OARWvv9BQdbcuzBqznUdcllbmRl94kA5zXPvAz0dOBPQFU4X/t6dkxxH+8JFj
mA/c2PHEyOtuFDOoqZxE
=RlHG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Fixes for ARM and aarch64.
This pull request is coming a bit later than I would have preferred,
because I and Gleb happened to have holidays around the same weeks of
August... sorry about that"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: ARM: Squash len warning
arm64: KVM: use 'int' instead of 'u32' for variable 'target' in kvm_host.h.
arm64: KVM: add missing dsb before invalidating Stage-2 TLBs
arm64: KVM: perform save/restore of PAR_EL1
arm64: KVM: fix 2-level page tables unmapping
ARM: KVM: Fix unaligned unmap_range leak
ARM: KVM: Fix 64-bit coprocessor handling
This was a new driver in this merge window, so some
post-merge hardening is happening.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=fGdI
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Fixes for the sunxi (AllWinner) pin control driver. This was a new
driver in this merge window, so some post-merge hardening is
happening"
[ I had completely missed this pull request for some reason, it was sent
over a week ago but my mailbox is chaotic ]
* tag 'pinctrl-for-v3.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunxi: Add spinlocks
pinctrl: sunxi: Fix gpio_set behaviour
pinctrl: sunxi: Read register before writing to it in irq_set_type
There is a nasty bug in the SCSI SG_IO ioctl that in some circumstances
leads to one process writing data into the address space of some other
random unrelated process if the ioctl is interrupted by a signal.
What happens is the following:
- A process issues an SG_IO ioctl with direction DXFER_FROM_DEV (ie the
underlying SCSI command will transfer data from the SCSI device to
the buffer provided in the ioctl)
- Before the command finishes, a signal is sent to the process waiting
in the ioctl. This will end up waking up the sg_ioctl() code:
result = wait_event_interruptible(sfp->read_wait,
(srp_done(sfp, srp) || sdp->detached));
but neither srp_done() nor sdp->detached is true, so we end up just
setting srp->orphan and returning to userspace:
srp->orphan = 1;
write_unlock_irq(&sfp->rq_list_lock);
return result; /* -ERESTARTSYS because signal hit process */
At this point the original process is done with the ioctl and
blithely goes ahead handling the signal, reissuing the ioctl, etc.
- Eventually, the SCSI command issued by the first ioctl finishes and
ends up in sg_rq_end_io(). At the end of that function, we run through:
write_lock_irqsave(&sfp->rq_list_lock, iflags);
if (unlikely(srp->orphan)) {
if (sfp->keep_orphan)
srp->sg_io_owned = 0;
else
done = 0;
}
srp->done = done;
write_unlock_irqrestore(&sfp->rq_list_lock, iflags);
if (likely(done)) {
/* Now wake up any sg_read() that is waiting for this
* packet.
*/
wake_up_interruptible(&sfp->read_wait);
kill_fasync(&sfp->async_qp, SIGPOLL, POLL_IN);
kref_put(&sfp->f_ref, sg_remove_sfp);
} else {
INIT_WORK(&srp->ew.work, sg_rq_end_io_usercontext);
schedule_work(&srp->ew.work);
}
Since srp->orphan *is* set, we set done to 0 (assuming the
userspace app has not set keep_orphan via an SG_SET_KEEP_ORPHAN
ioctl), and therefore we end up scheduling sg_rq_end_io_usercontext()
to run in a workqueue.
- In workqueue context we go through sg_rq_end_io_usercontext() ->
sg_finish_rem_req() -> blk_rq_unmap_user() -> ... ->
bio_uncopy_user() -> __bio_copy_iov() -> copy_to_user().
The key point here is that we are doing copy_to_user() on a
workqueue -- that is, we're on a kernel thread with current->mm
equal to whatever random previous user process was scheduled before
this kernel thread. So we end up copying whatever data the SCSI
command returned to the virtual address of the buffer passed into
the original ioctl, but it's quite likely we do this copying into a
different address space!
As suggested by James Bottomley <James.Bottomley@hansenpartnership.com>,
add a check for current->mm (which is NULL if we're on a kernel thread
without a real userspace address space) in bio_uncopy_user(), and skip
the copy if we're on a kernel thread.
There's no reason that I can think of for any caller of bio_uncopy_user()
to want to do copying on a kernel thread with a random active userspace
address space.
Huge thanks to Costa Sapuntzakis <costa@purestorage.com> for the
original pointer to this bug in the sg code.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: David Milburn <dmilburn@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We want ppc64 to be able to select between optimised assembly
checksum routines in big endian and the generic lib/checksum.c
routines in little endian.
The lpfc driver is forcing CONFIG_GENERIC_CSUM on which means
we are unable to make the decision to enable it in the arch
Kconfig. If the option exists it is always forced on.
This got introduced in 3.10 via commit 6a7252fdb0 ([SCSI] lpfc:
fix up Kconfig dependencies). I spoke to Randy about it and
the original issue was with CRC_T10DIF not being defined.
As such, remove the select of CONFIG_GENERIC_CSUM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 385904f819 ('sfc: Don't use
efx_filter_{build,hash,increment}() for default MAC filters') used the
wrong name to find the index of default RX MAC filters at insertion/
update time. This could result in memory corruption and would in any
case silently fail to update the filter.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
It's not allowed to clear masks of a cpuset if there're tasks in it,
but it's broken:
# mkdir /cgroup/sub
# echo 0 > /cgroup/sub/cpuset.cpus
# echo 0 > /cgroup/sub/cpuset.mems
# echo $$ > /cgroup/sub/tasks
# echo > /cgroup/sub/cpuset.cpus
(should fail)
This bug was introduced by commit 88fa523bff
("cpuset: allow to move tasks to empty cpusets").
tj: Dropped temp bool variables and nestes the conditionals directly.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The VLAN code needs to know the length of the per-port VLAN bitmap to
perform its most basic operations (retrieving VLAN informations, removing
VLANs, forwarding database manipulation, etc). Unfortunately, in the
current implementation we are using a macro that indicates the bitmap
size in longs in places where the size in bits is expected, which in
some cases can cause what appear to be random failures.
Use the correct macro.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 77145f1cbd was introduced
error which cause that reclocking on nv40 not working anymore.
There is missing assigment of return value from pll_calc to ret.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allocating type=0 marks the memory as free. This allows the ltcg memory
to be allocated twice.
Add a BUG_ON in core/mm.c to prevent this ever happening again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some registers were not initialized in init, this causes them to be
uninitialized after suspend.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit dceef5d87 (drm/nouveau/fb: initialise vram controller as pfb
sub-object) moved some code around and introduced these null derefs.
pfb->ram is set to the new ram object outside of this ctor.
Reported-by: Ronald Uitermark <ronald645@gmail.com>
Tested-by: Ronald Uitermark <ronald645@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
John W. Linville says:
====================
Regarding the iwlwifi bits, Johannes says:
"We revert an rfkill bugfix that unfortunately caused more bugs, shuffle
some code to avoid touching the PCIe device before it's enabled and
disconnect if firmware fails to do our bidding. I also have Stanislaw's
fix to not crash in some channel switch scenarios."
As for the mac80211 bits, Johannes says:
"This time, I have one fix from Dan Carpenter for users of
nl80211hdr_put(), and one fix from myself fixing a regression with the
libertas driver."
Along with the above...
Dan Carpenter fixes some incorrectly placed "address of" operators
in hostap that caused copying of junk data.
Jussi Kivilinna corrects zd1201 to use an allocated buffer rather
than the stack for a URB operation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
getsockopt PACKET_STATISTICS returns tp_packets + tp_drops. Commit
ee80fbf301 ("packet: account statistics only in tpacket_stats_u")
cleaned up the getsockopt PACKET_STATISTICS code.
This also changed semantics. Historically, tp_packets included
tp_drops on return. The commit removed the line that adds tp_drops
into tp_packets.
This patch reinstates the old semantics.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix a problem in the rtl8211 where the driver
wasn't properly enabled the interrupt on link change status.
it has to enable the ineterrupt on the bit 10 in the register 18
(INER).
Reported-by: Sharma Bhupesh <B45370@freescale.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Check if the skb has been correctly prepared before going on
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=gllO
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included change:
- Check if the skb has been correctly prepared before going on
Do not clear Broadcast/Multicast/Unicast Wake Flag or LanWake in
Config5. This is necessary to preserve WOL state when the driver is
loaded. Although the r8168 vendor driver does not write Config5 (it has
been commented out), Hayes Wang from Realtek said that masking bits like
this is more sensible.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If via_ircc_open() fails, data structures of the driver left uninitialized,
but probe (via_init_one()) returns zero. That can lead to null pointer dereference
in via_remove_one(), since it does not check drvdata for NULL.
The patch implements proper error code propagation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user turns off VNET_HDR support on the
macvtap device, there is no way to provide any
offload information to the user. So, it's safer
to ignore offload setting then depend on the user
setting them correctly.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user turns off IFF_VNET_HDR flag, attempts to change
offload features via TUNSETOFFLOAD do not work. This could cause
GSO packets to be delivered to the user when the user is
not prepared to handle them.
To solve, allow processing of TUNSETOFFLOAD when IFF_VNET_HDR is
disabled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In macvtap, tap_features specific the features of that the user
has specified via ioctl(). If we treat macvtap as a macvlan+tap
then we could all the tap a pseudo-device and give it other features
like SG and GSO. Then we can stop using the features of lower
device (macvlan) when forwarding the traffic the tap.
This solves the issue of possible checksum offload mismatch between
tap feature and macvlan features.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent.
The "when" field must be set for such skb. It's used in tcp_rearm_rto
for example. If the "when" field isn't set, the retransmit timeout can
be calculated incorrectly and a tcp connected can stop for two minutes
(TCP_RTO_MAX).
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The branch emulation needs to handle the OCTEON BBIT instructions,
otherwise we get SIGILL instead of emulation.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An older PVHVM guest (v3.0 based) crashed during vCPU hot-plug with:
kernel BUG at drivers/xen/events.c:1328!
RCU has detected that a CPU has not entered a quiescent state within the
grace period. It needs to send the CPU a reschedule IPI if it is not
offline. rcu_implicit_offline_qs() does this check:
/*
* If the CPU is offline, it is in a quiescent state. We can
* trust its state not to change because interrupts are disabled.
*/
if (cpu_is_offline(rdp->cpu)) {
rdp->offline_fqs++;
return 1;
}
Else the CPU is online. Send it a reschedule IPI.
The CPU is in the middle of being hot-plugged and has been marked online
(!cpu_is_offline()). See start_secondary():
set_cpu_online(smp_processor_id(), true);
...
per_cpu(cpu_state, smp_processor_id()) = CPU_ONLINE;
start_secondary() then waits for the CPU bringing up the hot-plugged CPU to
mark it as active:
/*
* Wait until the cpu which brought this one up marked it
* online before enabling interrupts. If we don't do that then
* we can end up waking up the softirq thread before this cpu
* reached the active state, which makes the scheduler unhappy
* and schedule the softirq thread on the wrong cpu. This is
* only observable with forced threaded interrupts, but in
* theory it could also happen w/o them. It's just way harder
* to achieve.
*/
while (!cpumask_test_cpu(smp_processor_id(), cpu_active_mask))
cpu_relax();
/* enable local interrupts */
local_irq_enable();
The CPU being hot-plugged will be marked active after it has been fully
initialized by the CPU managing the hot-plug. In the Xen PVHVM case
xen_smp_intr_init() is called to set up the hot-plugged vCPU's
XEN_RESCHEDULE_VECTOR.
The hot-plugging CPU is marked online, not marked active and does not have
its IPI vectors set up. rcu_implicit_offline_qs() sees the hot-plugging
cpu is !cpu_is_offline() and tries to send it a reschedule IPI:
This will lead to:
kernel BUG at drivers/xen/events.c:1328!
xen_send_IPI_one()
xen_smp_send_reschedule()
rcu_implicit_offline_qs()
rcu_implicit_dynticks_qs()
force_qs_rnp()
force_quiescent_state()
__rcu_process_callbacks()
rcu_process_callbacks()
__do_softirq()
call_softirq()
do_softirq()
irq_exit()
xen_evtchn_do_upcall()
because xen_send_IPI_one() will attempt to use an uninitialized IRQ for
the XEN_RESCHEDULE_VECTOR.
There is at least one other place that has caused the same crash:
xen_smp_send_reschedule()
wake_up_idle_cpu()
add_timer_on()
clocksource_watchdog()
call_timer_fn()
run_timer_softirq()
__do_softirq()
call_softirq()
do_softirq()
irq_exit()
xen_evtchn_do_upcall()
xen_hvm_callback_vector()
clocksource_watchdog() uses cpu_online_mask to pick the next CPU to handle
a watchdog timer:
/*
* Cycle through CPUs to check if the CPUs stay synchronized
* to each other.
*/
next_cpu = cpumask_next(raw_smp_processor_id(), cpu_online_mask);
if (next_cpu >= nr_cpu_ids)
next_cpu = cpumask_first(cpu_online_mask);
watchdog_timer.expires += WATCHDOG_INTERVAL;
add_timer_on(&watchdog_timer, next_cpu);
This resulted in an attempt to send an IPI to a hot-plugging CPU that
had not initialized its reschedule vector. One option would be to make
the RCU code check to not check for CPU offline but for CPU active.
As becoming active is done after a CPU is online (in older kernels).
But Srivatsa pointed out that "the cpu_active vs cpu_online ordering has been
completely reworked - in the online path, cpu_active is set *before* cpu_online,
and also, in the cpu offline path, the cpu_active bit is reset in the CPU_DYING
notification instead of CPU_DOWN_PREPARE." Drilling in this the bring-up
path: "[brought up CPU].. send out a CPU_STARTING notification, and in response
to that, the scheduler sets the CPU in the cpu_active_mask. Again, this mask
is better left to the scheduler alone, since it has the intelligence to use it
judiciously."
The conclusion was that:
"
1. At the IPI sender side:
It is incorrect to send an IPI to an offline CPU (cpu not present in
the cpu_online_mask). There are numerous places where we check this
and warn/complain.
2. At the IPI receiver side:
It is incorrect to let the world know of our presence (by setting
ourselves in global bitmasks) until our initialization steps are complete
to such an extent that we can handle the consequences (such as
receiving interrupts without crashing the sender etc.)
" (from Srivatsa)
As the native code enables the interrupts at some point we need to be
able to service them. In other words a CPU must have valid IPI vectors
if it has been marked online.
It doesn't need to handle the IPI (interrupts may be disabled) but needs
to have valid IPI vectors because another CPU may find it in cpu_online_mask
and attempt to send it an IPI.
This patch will change the order of the Xen vCPU bring-up functions so that
Xen vectors have been set up before start_secondary() is called.
It also will not continue to bring up a Xen vCPU if xen_smp_intr_init() fails
to initialize it.
Orabug 13823853
Signed-off-by Chuck Anderson <chuck.anderson@oracle.com>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When a event is being bound to a VCPU there is a window between the
EVTCHNOP_bind_vpcu call and the adjustment of the local per-cpu masks
where an event may be lost. The hypervisor upcalls the new VCPU but
the kernel thinks that event is still bound to the old VCPU and
ignores it.
There is even a problem when the event is being bound to the same VCPU
as there is a small window beween the clear_bit() and set_bit() calls
in bind_evtchn_to_cpu(). When scanning for pending events, the kernel
may read the bit when it is momentarily clear and ignore the event.
Avoid this by masking the event during the whole bind operation.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
CC: stable@vger.kernel.org
The sizeof() argument in init_evtchn_cpu_bindings() is incorrect
resulting in only the first 64 (or 32 in 32-bit guests) ports having
their bindings being initialized to VCPU 0.
In most cases this does not cause a problem as request_irq() will set
the irq affinity which will set the correct local per-cpu mask.
However, if the request_irq() is called on a VCPU other than 0, there
is a window between the unmasking of the event and the affinity being
set were an event may be lost because it is not locally unmasked on
any VCPU. If request_irq() is called on VCPU 0 then local irqs are
disabled during the window and the race does not occur.
Fix this by initializing all NR_EVENT_CHANNEL bits in the local
per-cpu masks.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
Mark Brown
Tushar Behera
Michael Grzeschik
Steffen Trumtrar
Markus Pargmann
Takashi Iwai
Kailang Yang
Knut Petersen
Nicolin Chen
Sachin Kamat
Stephen Warren
Daniel Gimpelevich
Wladislav Wiebe
Guillaume Clement
Dave Airlie
Linus Torvalds
Roland Dreier
Anton Blanchard
Ben Hutchings
Li Zefan
Toshiaki Makita
Ben Skeggs
Pali Rohár
Maarten Lankhorst
Maarten Lankhorst
Ilia Mirkin
David S. Miller
Willem de Bruijn
Giuseppe CAVALLARO
Peter Wu
Alexey Khoroshilov
Vlad Yasevich
Andrey Vagin
David Daney
Chuck Anderson
David Vrabel