We'll leak the memory allocated to 'urb' in
drivers/net/usb/usbnet.c:kevent() when we 'goto fail_lowmem' and the 'urb'
variable goes out of scope while still completely unused.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two bugs introduced by the commit
c659c38b27 ("tlan: Code cleanup:
checkpatch.pl is relatively happy now.") In that change,
TLAN_CSTAT_READY was considered as a bit mask containing a single bit
set while it was actually had two set instead.
Many thanks to Dan Carpenter for finding the mistake.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->master is now tightly connected to bonding driver. This patch makes
this pointer more general and ready to be used by others.
- netdev_set_master() - bond specifics moved to new function
netdev_set_bond_master()
- introduced netif_is_bond_slave() to check if device is a bonding slave
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded depends on PHYLIB. The config selection is already in
an if PHYLIB / endif block.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
WOL is not supported for Vrtual Functions.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid accessing the hardware when UE is detected.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_cmd_pmac_add/del functions need to pass domain number to the firmware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are always using the Emulex OUI for a VF MAC address
while generating MAC for a VF. Use OUI from current MAC instead.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF needs to cleanup all the interface handles that it created for the VFs.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the completion processing for be_vf_eth_addr_config
to consume the link status notification before netdev_register.
Otherwise this causes the PF miss its first link status update.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While configuring QOS for VFs, the VF number should be translated
to domain number correctly.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the phy.c codes for rtl8192ce and rtl8192cu be as alike as possible.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make rtlwifi/rtl8192ce/fw.{h,c} match what will be needed for
rtlwifi/rtl8192cu.{h,c}.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To reuse as much code as possible when adding additional drivers to the
rtlwifi tree, the common parts of various routines are moved to
drivers/net/wireless/rtlwifi. This patch does that for the version of
dm.{h,c} used by rtl8192ce.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtlwifi core needs some changes before inclusion of a driver
for the RTL8192CU USB device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: <chaoming_li@realsil.com.cn>
Signed-off-by: <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The atl1 driver uses the legacy PCI power management, so it has to
do some PCI-specific things in its ->suspend() and ->resume()
callbacks, which isn't necessary and should better be done by the PCI
subsystem-level power management code.
Convert atl1 to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1c driver shouldn't call device_init_wakeup() in its probe
routine with the second argument equal to 1, because for PCI devices
the wakeup capability setting is initialized as appropriate by the
PCI subsystem. Remove the potentially harmful call.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver uses device_init_wakeup() in such a way that the
device's power.can_wakeup flag may be set even though the PCI
subsystem cleared it before, in which case the device cannot wake
up the system from sleep states. Modify the driver to only change
the power.can_wakeup flag if the device is not capable of generating
wakeup signals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver does not show 100MB support in ethtool.
Adding support for the same.
Signed-off-by: Atita Shirwaikar <atita.shirwaikar@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ixgbe_init_mbx_params_pf isn't used unless CONFIG_PCI_IOV
is defined. This is causing namespace warnings. So I wrapped its
definition in CONFIG_PCI_IOV too.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We had a support function that just walked a few pointers to get
from the ixgbe_hw struct to the netdev pointer. This was causing
a namespace warning so I removed it and just reference the pointers
directly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We didn't need the prototype and it was causing namespace complaints so
I made it static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This consolidates hardware specifics to ixgbe_dcb.c this simplifies
code that was previously branching based on hardware type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes the RESET bit previously used to force a device
reset when DCB bandwidth configurations were changed. This can
now be done dynamically without a reset so the bit is no longer
needed. The only remaining operations that force a device reset
are DCB enable/disable and FCoE application priority changes.
DCB enable/disable is a hardware requirement.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and 82598 devices do not require hardware resets to
configure CEE pg settings. This patch changes DCB configuration
to set the CEE pg values directly from the dcbnl ops routine.
This reduces the number of resets seen on the wire and allows
LLDP to reach a steady state faster.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.
This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.
The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove round robin configuration code for 82598 parts it
is not settable and is always false.
If we need/want this in the future we can add it back properly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.
The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.
This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.
By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds full support for SR-IOV by enabling the PF side.
VF side has already been committed.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...when invoked while interface is not up or when auto-negotiation is
disabled as done by other drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
*e1000_gstrings_test is not the same size as e1000_gstrings_test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As a precautionary measure, expand the fix submitted in commit
4d163b75e9 entitled "tg3: Fix 5719 A0 tx
completion bug" to apply to all 5719 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
virtio_net: Add schedule check to napi_enable call
x25: Do not reference freed memory.
pch_can: fix tseg1/tseg2 setting issue
isdn: hysdn: Kill (partially buggy) CVS regision log reporting.
can: softing_cs needs slab.h
pch_gbe: Fix the issue which a driver locks when rx offload is set by ethtool
netfilter: nf_conntrack: set conntrack templates again if we return NF_REPEAT
pch_can: fix module reload issue with MSI
pch_can: fix rmmod issue
pch_can: fix 800k comms issue
net: Fix lockdep regression caused by initializing netdev queues too early.
net/caif: Fix dangling list pointer in freed object on error.
USB CDC NCM errata updates for cdc_ncm host driver
CDC NCM errata updates for cdc.h
ixgbe: update version string
ixgbe: cleanup variable initialization
ixgbe: limit VF access to network traffic
ixgbe: fix for 82599 erratum on Header Splitting
ixgbe: fix variable set but not used warnings by gcc 4.6
e1000: add support for Marvell Alaska M88E1118R PHY
...
Under harsh testing conditions, including low memory, the guest would
stop receiving packets. With this patch applied we no longer see any
problems in the driver while performing these tests for extended periods
of time.
Make sure napi is scheduled subsequent to each napi_enable.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Olaf Kirch <okir@suse.de>
Cc: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch "[PATCH 1/3] pch_can: fix 800k comms issue" is wrong.
I should have modified tseg1_min not tseg2_min.
This patch reverts tseg2_min to 1 and set tseg1_min to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combo devices have TX statistics on different place, because
struct statistics_rx_bt and struct statistics_rx have different
size. User proper values on combo devices instead of random data.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make ack health code easies to read. Compared to previous
code, we do not print debug messages when expected_ack_cnt_delta == 0
and also do check against negative deltas.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional change, make recover from statistics code
easies to read.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable appears in both ath_softc and ath_beacon_config.
The struct ath_beacon_config is embedded in ath_softc. The redundant
variable was added by commit id 57c4d7b4c4.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Reviewed-by: Mohammed Shafi <shafi.ath9k@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Randy Dunlap <randy.dunlap@oracle.com>
softing_cs.c uses kzalloc & kfree, so it needs to include linux/slab.h.
drivers/net/can/softing/softing_cs.c:234: error: implicit declaration of function 'kfree'
drivers/net/can/softing/softing_cs.c:271: error: implicit declaration of function 'kzalloc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599
Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.
For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.
Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver will be in a deadlock, When the rx offload is set by ethtool.
The pch_gbe_reinit_locked function was modified.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of looking for supported_rates change on every tx packet,
just extract the supported_rates after association completes (station only).
Remove wl1271.sta_rate_set and WL1271_FLAG_STA_RATES_CHANGED which are
not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
make the configuration management more flexible by using the
conf struct, rather than predefined macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This patch adds support for the new wl12xx firmware (Rev 6.1.3.50.49)
Since this fw is not backward compatible with previous fw versions,
a new fw (with different name) is being fetched.
(the patch is big because it contains all the required fw api changes.
splitting it into multiple patches will result in corrupted intermediate
commits)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
mcp2.5 uses this acx to configure the fw only once, rather than
passing the params in every enter psm command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, in case reload pch_can,
pch_can not to be able to catch interrupt.
The cause is bus-master is not set in pch_can.
Thus, add enabling bus-master processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when rmmod pch_can, kernel failure occurs.
The cause is pci_iounmap executed before pch_can_reset.
Thus pci_iounmap moves after pch_can_reset.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, 800k comms fails since prop_seg set zero.
(EG20T PCH CAN register of prop_seg must be set more than 1)
To prevent prop_seg set to zero, change tseg2_min 1 to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specification links:
- CDC NCM errata link:
http://www.usb.org/developers/devclass_docs/NCM10_012011.zip
- CDC and WMC errata link:
http://www.usb.org/developers/devclass_docs/CDC1.2_WMC1.1_012011.zip
Changes:
- driver updated to match cdc.h header with errata changes
- added support for USB_CDC_SET_NTB_INPUT_SIZE control request with
8 byte length
- fixes to comply with specification: send only control requests supported by
device, set number of datagrams for IN direction, connection speed structure
update, etc.
- packet loss fixed for tx direction; misleading flag renamed.
- adjusted hard_mtu value.
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will synchronize the version string with that of the latest source
forge driver which shares its functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_fcoe_ddp_get function wasn't initializing one of its variables
and this was producing compiler warnings. This patch cleans that up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes VM pool allocation issues based on MAC address filtering,
as well as limits the scope of VF access to promiscuous mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have found a hardware erratum on 82599 hardware that can lead to
unpredictable behavior when Header Splitting mode is enabled. So
we are no longer enabling this feature on affected hardware.
Please see the 82599 Specification Update for more information.
CC: stable@kernel.org
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Caught with gcc 4.6 -Wunused-but-set-variable
Remove unused napi_vectors variable.
Fix the use of reset_bit in ixgbe_reset_hw_X540()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for Marvell Alask M88E188R PHY chips. Support for
other M88* PHYs is already there, so there is nothing more to add than its
PHY id.
CC: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver increments the tx_timeout counter (an error counter)
when simply resetting the part with outstanding transmit work pending.
This is an unnecessary count of an error, when all we should be doing is
just resetting the part and discarding the transmits. With this change the
only increment of tx_timeout is when the stack calls the watchdog reset
function due to a true Tx timeout.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add few comments for not parsing DTIM period from mac80211
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast channel change fixes:
a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With commit 554d1d027b only one RF_KILL
interrupt will be seen by the driver when the interface is down.
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove support for an older version (A1) of hardware
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware requires CMD_IG_VLAN_REWRITE_MODE be issued before a CMD_INIT.
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix enic_add/del_station_addr routines to return appropriate error code when an invalid address is added or deleted.
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Organize the wrapper routines for firmware devcmds into a separate file.
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes VM mac address registration and deregistration code during
port profile set operation. We can delay mac address registration until
enic_open.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completed the bnx2x_set_rx_mode() to a proper netdev->ndo_set_rx_mode
implementation:
- Added a missing configuration of a unicast MAC addresses list.
- Changed bp->dma_lock from being a mutex to a spinlock as long as it's taken
under netdev->addr_list_lock now.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent packets duplication for frames targeting FCoE L2 ring:
packets were arriving to stack from both L2 RSS and from FCoE
L2 in a promiscuous mode.
Configure FCoE L2 ring to DROP_ALL rx mode, when interface is
configured to PROMISC, and to accept only unicast frames, when
interface is configured to ALL_MULTI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always configure an FCoE L2 ring with a mini-jumbo MTU size (2500).
To do that we had to move the rx_buf_size parameter from per
function level to a per ring level.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fix memory leak in error path of sis900_rx(). If we don't do this we'll
leak the skb we dev_alloc_skb()'ed just a few lines above when the
variable goes out of scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since even with the latest changes the false positive issue of the baseband
hang check is not fully solved yet, additional checks are needed.
If the baseband hang occurs, the rx_clear signal will be stuck to high, so
we can use the cycle counters to confirm it.
With this patch, a hardware reset is only triggered if the baseband hang
check returned true three times in a row, with a beacon interval between
each check and if the busy time was also 99% or more during the check
intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register writes to the key cache have to be done in pairs. However,
the clearing of a separate MIC entry with hardware revisions that use
combined MIC key layout did not do that with one of the registers. Add
the matching register write to the following register to make the KEY4
register write actually complete.
This is mostly a fix for a theoretical issue since the incorrect entry
that could potentially be left behind in the key cache would not match
with received frames. Anyway, better make this code clean the entry
correctly using paired register writes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It should be safe to enable AP-mode now.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix
this. Do reset 30 seconds after last rx.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver fails to acquire device semaphore lock, device usually
freezes soon afterwards. So failing to acquire lock indicates us that
not everything is going right in device/fw. So reset device when
this happens.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need HW hard reset later in patchset to reset device after TX-stall.
Collect all settings that we have set to driver for later reset and
add restore function.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:
[ 473.074419] zd1211rw 1-1:1.0: print_times() Read times:
[ 473.175163] zd1211rw 1-1:1.0: print_time() 0 - 10 msec: 1506
[ 473.176429] zd1211rw 1-1:1.0: print_time() 11 - 50 msec: 0
[ 473.177955] zd1211rw 1-1:1.0: print_time() 51 - 100 msec: 0
[ 473.180703] zd1211rw 1-1:1.0: print_time() 101 - 250 msec: 0
[ 473.182101] zd1211rw 1-1:1.0: print_time() 251 - 500 msec: 0
[ 473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20
[ 473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18
Also vendor driver doesn't use this long timeout. Therefore change
timeout to 50msec.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As might lower beacon update CPU usage.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated
buffer in zd_usb.c. This might lower CPU usage for beacon setup.
v2:
- Do not use stack buffers in zd_usb.c as they would be used for urb
transfer_buffer.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon config function writes beacon to hw one write per byte. This is very
slow (usually taking more than 100ms to finish) and causes high CPU usage
when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands
together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower
CPU usage to saner levels (<10% on Atom).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing tx/rx at high packet rate (for example simply using ping -f),
device starts to fail to respond to control messages. On non-AP modes
this only causes problems for LED updating code but when we are running
in AP-mode we are writing new beacon to HW usually every 100ms. Now if
control message fails in HW beacon setup, device lock is kept locked
and beacon data partially written. This can and usually does cause:
1. HW beacon setup fail now on, as driver cannot acquire device lock.
2. Beacon-done interrupt stop working as device has incomplete beacon.
Therefore make zd_mac_config_beacon() always try to release device lock
and add beacon watchdog to restart beaconing when stall is detected.
Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms,
as what old code appeared to be trying to do using loop and msleep(1).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for AP-mode beacon. Also disable beacon when interface is set
down as otherwise hw will keep flooding NEXT_BCN interrupts.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.
Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.
So don't use mac->ack_pending when in AP-mode.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As bss_info_changed may sleep, we can as well set RTS_CTS register right away.
Keep mac->short_preamble for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Workers not needed anymore since configure_filter may sleep. Keep
mac->multicast_hash for later use (hw reset).
Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.
Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OOPS if worker is running and disconnect() is called (triggered
by unpluging device). Much harder to trigger at this stage but
later when we have AP beacon work in process_intr it happens very
easy.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.
It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().
Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.
Patch makes tx-urb handling saner with use of urb anchors.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (68 commits)
net: can: janz-ican3: world-writable sysfs termination file
net: can: at91_can: world-writable sysfs files
MAINTAINERS: update email ids of the be2net driver maintainers.
bridge: Don't put partly initialized fdb into hash
r8169: prevent RxFIFO induced loops in the irq handler.
r8169: RxFIFO overflow oddities with 8168 chipsets.
r8169: use RxFIFO overflow workaround for 8168c chipset.
include/net/genetlink.h: Allow genlmsg_cancel to accept a NULL argument
net: Provide compat support for SIOCGETMIFCNT_IN6 and SIOCGETSGCNT_IN6.
net: Support compat SIOCGETVIFCNT ioctl in ipv4.
net: Fix bug in compat SIOCGETSGCNT handling.
niu: Fix races between up/down and get_stats.
tcp_ecn is an integer not a boolean
atl1c: Add missing PCI device ID
s390: Fix possibly wrong size in strncmp (smsgiucv)
s390: Fix wrong size in memcmp (netiucv)
qeth: allow OSA CHPARM change in suspend state
qeth: allow HiperSockets framesize change in suspend
qeth: add more strict MTU checking
qeth: show new mac-address if its setting fails
...
This patch fixes a off-by-one bug which bugged
the driver's PS-POLL capability.
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't allow everybody to set terminator via sysfs.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't allow everybody to write to mb0_id file.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the RxFIFO interruption is masked for most 8168, nothing prevents
it to appear in the irq status word. This is no excuse to crash.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>
Some experiment-based action to prevent my 8168 chipsets locking-up hard
in the irq handler under load (pktgen ~1Mpps). Apparently a reset is not
always mandatory (is it at all ?).
- RTL_GIGA_MAC_VER_12
- RTL_GIGA_MAC_VER_25
Missed ~55% packets. Note:
- this is an old SiS 965L motherboard
- the 8168 chipset emits (lots of) control frames towards the sender
- RTL_GIGA_MAC_VER_26
The chipset does not go into a frenzy of mac control pause when it
crashes yet but it can still be crashed. It needs more work.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>
I found that one of the 8168c chipsets (concretely XID 1c4000c0) starts
generating RxFIFO overflow errors. The result is an infinite loop in
interrupt handler as the RxFIFOOver is handled only for ...MAC_VER_11.
With the workaround everything goes fine.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Use DMA API as PCI equivalents will be deprecated.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Flavio Leitner, there is no synchronization to protect
NIU's get_stats method from seeing a NULL pointer in either
np->rx_rings or np->tx_rings. In fact, as far as ->ndo_get_stats
is concerned, these values are set completely asynchronously.
Flavio attempted to fix this using a RW semaphore, which in fact
works most of the time. However, dev_get_stats() can be invoked
from non-sleepable contexts in some cases, so this fix doesn't
work in all cases.
So instead, control the visibility of the np->{rx,tx}_ring pointers
when the device is being brough up, and use properties of the device
down sequence to our advantage.
In niu_get_stats(), return immediately if netif_running() is false.
The device shutdown sequence first marks the device as not running (by
clearing the __LINK_STATE_START bit), then it performans a
synchronize_rcu() (in dev_deactive_many()), and then finally it
invokes the driver ->ndo_stop() method.
This guarentees that all invocations of niu_get_stats() either see
netif_running() as false, or they see the channel pointers before
->ndo_stop() clears them out.
If netif_running() is true, protect against startup races by loading
the np->{rx,tx}_rings pointer into a local variable, and punting if
it is NULL. Use ACCESS_ONCE to prevent the compiler from reloading
the pointer on us.
Also, during open, control the order in which the pointers and the
ring counts become visible globally using SMP write memory barriers.
We make sure the np->num_{rx,tx}_rings value is stable and visible
before np->{rx,tx}_rings is.
Such visibility control is not necessary on the niu_free_channels()
side because of the RCU sequencing that happens during device down as
described above. We are always guarenteed that all niu_get_stats
calls are finished, or will see netif_running() false, by the time
->ndo_stop is invoked.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The below patch fixes a typo comamnd to command.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beaconing vif addition is based on max beacon slot
available. So it is better to reserve a beacon slot
on interface addition and let it be configured properly
on bss_info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The opmode recalculation is accessing hw registers.
When it is called from remove interface callback and
if there are no vifs present then hw is moved to FULL SLEEP
by radio disable. So use power save wrappers before
accessing hw registers in calculating opmode state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
move ath_update_txpow to common to remove code duplication
in both ath9k & ath9k_htc.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ani work is cancelled in dissaoctiation. But in some cases
during suspend, deauthention never be called. So we failed
to stop ani work which was identified by the following
warning.
Call Trace:
[<ffffffffa0454a1d>] ieee80211_can_queue_work.clone.17+0x2d/0x40 [mac80211]
[<ffffffffa0454a60>] ieee80211_queue_delayed_work+0x30/0x60 [mac80211]
[<ffffffffa0567f82>] ath9k_ani_work+0x142/0x250 [ath9k_htc]
[<ffffffff81073c70>] async_run_entry_fn+0x0/0x180
[<ffffffffa0567e40>] ath9k_ani_work+0x0/0x250 [ath9k_htc]
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the rate index rate_idx and preamble flag RX_FLAG_SHORTPRE on received
packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable adhoc support in wl1251 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement connection quality monitoring similar to the wl1271 driver.
It triggers ieee80211_cqm_rssi_notify with the corresponding event when
RSSI drops blow RSSI threshold or rises again above the RSSI threshold.
It should be noted that wl1251 doesn't support RSSI hysteresis, instead it
uses RSSI averageing and delays events until a certain count of frames
proved RSSI change.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port the beacon early termination feature from wl1251 driver version
included in the Maemo Fremantle kernel.
It is enabled when going to power-saving mode and disabled when leaving
power-saving mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements TX buffer alignment for cloned or too small skb by
copying and replacing the original skb.
Recent changes in wireless-testing seems to make this really necessary.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue stopping/waking functionality was broken in a way that could
cause the TX to stall if the right circumstances are met.
The problem was caused by tx_work, which is scheduled on each TX operation.
If the firmware buffer is full, tx_work does nothing. In combinition with
stopped queues or non-continues transfers, tx_work is never scheduled again.
Moreover the low watermark introduced by
9df86e2e70 never takes effect because of some
old code.
Solve this by scheduling tx_work every time tx_queue is non-empty and
firmware buffer is freed on tx_complete.
This also solves a possible but unlikely case: If less frames than the high
watermark are queued, but more than firmware buffer can hold. This results
in queues staying awake but the only scheduled tx_work doesn't transfer all
frames, so the remaining frames are stuck in the queue until more frames
get queued and tx_work is scheduled again.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To support suspend/resume in if_spi we need two things:
- re-setup fw in lbs_resume(), because if_spi powercycles card;
- don't touch hwaddr on second lbs_update_hw_spec() call for same
reason;
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use workqueue to perform SPI xfers, it's necessary to fix
nasty "BUG: scheduling while atomic", because
spu_write() calls spi_sync() and spi_sync() may sleep, but
hw_host_to_card() callback can be called from atomic context.
Remove kthread completely, workqueue now does its job.
Restore intermediate buffers which were removed in commit
86c34fe89e that introduced
mentioned bug.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Update missed conversion of flush_scheduled_work()
RDMA/ucma: Copy iWARP route information on queries
RDMA/amso1100: Fix compile warnings
RDMA/cxgb4: Set the correct device physical function for iWARP connections
RDMA/cxgb4: Limit MAXBURST EQ context field to 256B
IB/qib: Hold link for TX SERDES settings
mlx4_core: Add ConnectX-3 device IDs
Use DMA API as PCI equivalents will be deprecated.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8f574b35f2 ("atl1c: Add AR8151 v2
support and change L0s/L1 routine") added support for a new adapter
but failed to add it to the PCI device table.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is illegal to call netif_stop_queue before register_netdev.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running insmod/rmood in a loop, an unnecessary netif_stop_queue
causes the system to crash. Remove the netif_stop_queue call
and netif_start_queue in the link status update path.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip was erroneously configured to accept all multicast frames
in a normal (none-promisc) rx mode both on the RSS and on the FCoE L2 rings
when in an NPAR mode. This caused packet duplication for every received multicast
frame in this mode.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error is reported by cppcheck:
drivers/net/vxge/vxge-config.c:3693: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?
It looks like cppcheck is correct, so fix this. No test was run.
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This error was reported by cppcheck:
drivers/net/enc28j60.c:815: error: Using sizeof for array given as function argument returns the size of pointer.
The original code reads 4 or 8 bytes instead of TSV_SIZE (= 100) bytes.
I just fixed the code, but did not run any tests.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
axnet_cs:
mdelay of 10ms is too long at ei_rx_overrun.
It should be reduced to 2ms.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all shared mem code to bnx2x to avoid code duplication. bnx2x now
performs:
- Read the FCoE and iSCSI max connection information.
- Read the iSCSI and FCoE MACs from NPAR configuration in shmem.
- Block the CNIC for the current function if there is neither FCoE nor
iSCSI valid configuration by returning NULL from bnx2x_cnic_probe().
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.62.11-0
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded support for emulation/FPGA from the code
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CMS(Common Mode Sense) functionality for 848x3 as this reduces power consumption and allows a better 10G link stability
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new PHY BCM84833. This PHY is very similar to the BCM84823, only it has different register offset compared to the BCM84823, which needs to be handled correctly.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flexible support to control various SFP+ module features either throughout MDIO registers or GPIO pins according to NVRAM configuration
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and modify some net dev prints to improve error control
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix annoying compilation warning, mainly related to static declarations
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains cosmetic changes only of restyling comments according to Linux coding standard, and add comment for get_emac_base function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains cosmetic changes only of renaming CL45_WR_OVER_CL22 macro to CL22_WR_OVER_CL45 as it should be.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains cosmetic changes only to fix code alignment, and update copyright comment year
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the period of BT coex changes, REPLY_BT_COEX_SCO host command
is no longer needed to support SCO/eSCO type of traffic. delete it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Without this dependency the softing driver will be buildable on s390,
where it fails.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The beacon notification changed between 4965 and
agn because the embedded TX response changed, but
iwlwifi was never updated to know about this.
Update it now so the IBSS manager status will be
tracked correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Use the values from the peer to set up the ucode
for the right maximum number of subframes in an
aggregate. Since the ucode only tracks this per
station, use the minimum across all aggregation
sessions with this peer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Allow peers to size their reorder buffer more
accurately by advertising that we'll never send
aggregates longer than the default (31).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In order to support RSN IBSS, we need to
(ok actually maybe it's just easiest to)
disable group key programming so that any
group-addressed frames will be decrypted
in software which handles the per-station
keys for this easily. We could keep the
encryption in the device, but that takes
more work and seems unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The I/Q swapping is extremely important and should be dealt with extra care.
It will affects OFDM and CCK differently.
For 6000/6005/6030 series devices, the I/Q were swapped, and for 2000 series
devices, it is in non-swapped status (but its swapped with respected to 6000/6005/6030).
so the CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER register need to be set to support
the correct behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Driver check alive message from ucode, if it is not ok, then need
to restart the loading process. instead of checking multiple places
for failure, only need to check in once place when receive alive
message from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Commit 0b01f030d3 added a new argument
to the ampdu_action operation. The ampdu_action operation in the
wl12xx driver currently doesn't have that argument and this generates
a warning. This happened during merging of the latest mac80211
patches with the wl12xx BA patches.
CC [M] drivers/net/wireless/wl12xx/main.o
drivers/net/wireless/wl12xx/main.c:3035: warning: initialization from incompatible pointer type
The wl12xx driver doesn't need to do anything about the buf_size
argument since the AMPDU TX is fully handled by the firmware.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit 59eb21a650
"cfg80211: Extend channel to frequency mapping for 802.11j"
we use uninitialized sband->band when assign channel frequencies, what
results that 5GHz channels have erroneous (zero) center_freq value.
Patch fixes problem and simplifies code a bit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX work structures must be able to run independently
of other workqueues. This is because mac80211 might use
the flush() callback function from various context, which depends
on the TX/RX work to complete while the main thread is blocked
(until the the TX queues are empty).
This should reduce the number of 'Queue %d failed to flush' warnings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During device removal all pending work and tasklets must
be guaranteed to be halted. So far only the txstatus_tasklet
was killed.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both rt61pci and rt73usb check the Michael MIC in hardware and strip the
Michael MIC from received frames. This is perfectly allowed by mac80211 as
long as this is properly reported to mac80211.
Both these drivers reported the Michael MIC handling properly to mac80211, but
still contained a FIXME comment on this, which is not needed to be handled, since
mac80211 doesn't really need the Michael MIC in this case.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the specific mac field of the wcid_entry structure to copy the MAC
address to, instead of just overwriting the structure.
Previous code resulted in the same, but this form is cleaner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing a trivial comment typo.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CLOCK CYCLE: Clock cycle count in 1us
PCI:0x21, PCIE:0x7d, USB:0x1e
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove STATE_RADIO_IRQ_OFF_ISR and STATE_RADIO_IRQ_ON_ISR as they are
not used anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No driver uses interrupt threads anymore. Remove the remaining interrupt
thread artifacts.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.
Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.
As a nice bonus, the interrupt handling overhead should be much lower.
Compile-tested only.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jesper Juhl
Sakari Ailus
Jiri Pirko
hartleys
Ajit Khaparde
David S. Miller
Larry Finger
George
Wey-Yi Guy
Rafael J. Wysocki
Atita Shirwaikar
Don Skidmore
John Fastabend
Carolyn Wyborny
Bruce Allan
Matt Carlson
Linus Torvalds
Bruce Rogers
Tomoya MORINAGA
Stanislaw Gruszka
Steve Brown
Ben Greear
Randy Dunlap
Toshiharu Okada
Eliad Peller
Alexey Orishko
Alexander Duyck
Emil Tantilov
Florian Fainelli
Jesse Brandeburg
Geert Uytterhoeven
Mohammed Shafi Shajakhan
Nick Kossifidis
Don Fry
Vasanthy Kolluri
Roopa Prabhu
Vladislav Zolotarov
Johannes Berg
Felix Fietkau
Jouni Malinen
Jussi Kivilinna
Christian Lamparter
Vasiliy Kulikov
Francois Romieu
Ivan Vecera
Justin P. Mattock
Rajkumar Manoharan
David Gnedt
Vasily Khoruzhick
Chuck Ebbert
Alan Cox
Stefan Weil
John W. Linville
Ken Kawasaki
Yaniv Rosner
Luciano Coelho
Ivo van Doorn
Gertjan van Wingerde
Johannes Stezenbach
Mark Einon
RA-Jay Hung
Helmut Schaa