The wait_event() makes the application hang for ever in the following case:
[1] the hardware flow control is enabled.
[2] the other end (or the remote end) is terminated, and the TX is still
waiting for the hardware flow control signal to become asserted.
This patch fixes it by changing the wait_event to wait_event_interruptible.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the uart port is suspending, the RX data is useless.
So in this case, we can terminate the RX DMA right now.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the 'CTSC' bit is negated. 'CTS' has no function when 'CTSC' is asserted.
0: The CTS pin is high (inactive)
1: The CTS pin is low (active)
For throttle, it needs to clear 'CTS' and 'CTSC' bits.
For unthrottle, it needs to enable 'CTS' and 'CTSC' bits.
The patch just fix the issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.
Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.
This patch enables standard 8250 mode
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To determine the correct divisor, we need to know the difference between
the desired baud rate and the actual baud rate. The calculation for this
difference is implemented twice within omap_serial_baud_is_mode16().
Pull out the calculation for easier maintenance.
While at it, remove the CamelCasing from the variable names.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.
Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backend type is chosen by the toolstack. Regardless, the frontend
should not care, especially given that it cannot have an effect as the
backend is started before this code is run.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_startup() adds UART_IER_RDI and UART_IER_RLSI to ier.
serial8250_stop_rx() should remove both.
This is what the serial-omap driver has been doing and is now moved to
the 8250-core since it does no look to be *that* omap specific.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony noticed that the old omap-serial driver picked the uart "number"
based on the hint given from device tree or platform device's id.
The 8250 based omap driver doesn't do this because the core code does
not honour the ->line argument which is passed by the driver.
This patch aims to keep the same behaviour as with omap-serial. The
function will first try to use the line suggested ->line argument and
then fallback to the old strategy in case the port is taken.
That means the the third uart will always be ttyS2 even if the previous
two have not been enabled in DT.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:
|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
|Control: 10c5387d Table: 80004019 DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.
NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.
v5…v8:
- drop RPM from serial8250_set_mctrl() it will be used in
restore path which already has RPM active and holds
dev->power.lock
v4…v5:
- add a wrapper around rpm function and introduce UART_CAP_RPM
to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
- added runtime to the console code
- removed device_may_wakeup() from serial8250_set_sleep()
Cc: mika.westerberg@linux.intel.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP UART provides support for HW assisted flow control. What is
missing is the support to throttle / unthrottle callbacks which are used
by the omap-serial driver at the moment.
This patch adds the callbacks. It should be safe to add them since they
are only invoked from the serial_core (uart_throttle()) if the feature
flags are set.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While transmitting a START/STOP char for tcflow(TCION/TCIOFF), prevent
a termios change. Otherwise, a garbage in-band flow control char
may be sent, if the termios change overlaps the transmission setup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the file-scope function, send_prio_char(), as a global
helper tty_send_xchar(). Remove the global declarations for
tty_write_lock()/tty_write_unlock(), as these are file-scope only now.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use newly-introduced tty->flow_lock to serialize updates to
tty->flow_stopped (via tcflow()) and with concurrent tty flow
control changes from other sources.
Merge the storage for ->stopped and ->flow_stopped, now that both
flags are serialized by ->flow_lock.
The padding bits are necessary to force the compiler to allocate the
type specified; otherwise, gcc will ignore the type specifier and
allocate the minimum number of bytes necessary to store the bitfield.
In turn, this would allow Alpha EV4 and EV5 cpus to corrupt adjacent
byte storage because those cpus use RMW to store byte and short data.
gcc versions < 4.7.2 will also corrupt storage adjacent to bitfields
smaller than unsigned long on ia64, ppc64, hppa64 and sparc64, thus
requiring more than unsigned int storage (which would otherwise be
sufficient to workaround the Alpha non-atomic byte/short storage problem).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a master pty is set to packet mode, flow control changes to
the slave pty cause notifications to the master pty via reads and
polls. However, these tests are occurring for all ttys, not
just ptys.
Implement flow control packet mode notifications in the pty driver.
Only the slave side implements the flow control handlers since
packet mode is asymmetric; the master pty receives notifications
for slave-side changes, but not vice versa.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without serialization, the flow control state can become inverted
wrt. the actual hardware state. For example,
CPU 0 | CPU 1
stop_tty() |
lock ctrl_lock |
tty->stopped = 1 |
unlock ctrl_lock |
| start_tty()
| lock ctrl_lock
| tty->stopped = 0
| unlock ctrl_lock
| driver->start()
driver->stop() |
In this case, the flow control state now indicates the tty has
been started, but the actual hardware state has actually been stopped.
Introduce tty->flow_lock spinlock to serialize tty flow control changes.
Split out unlocked __start_tty()/__stop_tty() flavors for use by
ioctl(TCXONC) in follow-on patch.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_set_termios() is called with interrupts enabled; no need to
save and restore the interrupt state when taking the uart port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 64851636d5,
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS,
open-codes uart_handle_cts_change() when CONFIG_SERIAL_BFIN_HARD_CTSRTS
to skip start and stop tx.
But the CTS interrupt handler _still_ calls uart_handle_cts_change();
only call uart_handle_cts_change() if !CONFIG_SERIAL_BFIN_HARD_CTSRTS.
cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->hw_stopped is not used by the tty core and is thread-unsafe;
hw_stopped is a member of a bitfield whose fields are updated
non-atomically and no lock is suitable for serializing updates.
Replace serial core usage of tty->hw_stopped with uport->hw_stopped.
Use int storage which works around Alpha EV4/5 non-atomic byte storage,
since uart_port uses different locks to protect certain fields within the
structure.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core uses the tty port flags, ASYNC_CTS_FLOW and
ASYNC_CD_CHECK, to track whether CTS and DCD changes should be
ignored or handled. However, the tty port flags are not safe for
atomic bit operations and no lock provides serialized updates.
Introduce the struct uart_port status field to track CTS and DCD
enable states, and serialize access with uart port lock. Substitute
uart_cts_enabled() helper for tty_port_cts_enabled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core provides two helper functions, uart_handle_dcd_change()
and uart_handle_cts_change(), for UART drivers to use at interrupt
time. The serial core expects the UART driver to hold the uart port lock
when calling these helpers to prevent state corruption.
If lockdep enabled, trigger a warning if the uart port lock is not held
when calling these helper functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes COMPILE_TEST build of serial_mctrl_gpio module for
architectures with custom termios.h header.
sparc64:allmodconfig:
In file included from drivers/tty/serial/serial_mctrl_gpio.c:21:0:
include/uapi/asm-generic/termios.h:22:8: error: redefinition of 'struct termio'
./arch/sparc/include/uapi/asm/termbits.h:16:8: note: originally defined here
make[3]: *** [drivers/tty/serial/serial_mctrl_gpio.o] Error 1
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device has a highspeed register which influences the calcualtion
of the divisor. The chip lacks support for some baudrates. When requested,
we set the divisor to the next smaller baudrate and adjust the c_cflag
accordingly.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The architectures supported by this driver, arm and sh, have expensive
implementations of writel(), reliant on spin locks and explicit L2 cache
management. These architectures provide a cheaper writel_relaxed() which
is much better suited to peripherals that do not perform DMA. The
situation with readl()/readl_relaxed()is similar although less acute.
This driver does not use DMA and will be more power efficient and more
robust (due to absence of spin locks during console I/O) if it uses the
relaxed variants.
The driver supports COMPILE_TEST and therefore falls back to writel()
when writel_relaxed() does not exist.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: kernel@stlinux.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch fixes the following build error of CLPS711X serial driver for
targets without GPIOLIB support:
>> drivers/tty/serial/serial_mctrl_gpio.c:44:6: error: redefinition of 'mctrl_gpio_set'
void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl)
^
In file included from drivers/tty/serial/serial_mctrl_gpio.c:23:0:
drivers/tty/serial/serial_mctrl_gpio.h:80:6: note: previous definition of 'mctrl_gpio_set' was here
void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl)
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit: e676253b19 [3/21] serial/8250: Add
support for RS485 IOCTLs, adds a building error on arch m32r.
All error/warnings:
drivers/tty/serial/8250/8250_core.c: In function 'serial8250_ioctl':
>> drivers/tty/serial/8250/8250_core.c:2859:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
if (copy_from_user(&rs485_config, (void __user *)arg,
^
>> drivers/tty/serial/8250/8250_core.c:2871:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
if (copy_to_user((void __user *)arg, &up->rs485,
^
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_empty() callback currently checks the TXEMPTY bit in the interrupt
status register to decided whether the FIFO should be reported as empty or
not. The bit in this register gets set when the FIFO state transitions from
non-empty to empty but is cleared again in the interrupt handler. This means
it is not suitable to be used to decided whether the FIFO is currently empty
or not. Instead use the TXEMPTY bit from the status register which will be
set as long as the FIFO is empty.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In set_termios(), interrupts where not disabled if UART_ENABLE_MS() was
false.
Tested on at91sam9g35.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # >= 3.16
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another new ACPI identifier for the 8250 dw bindings to cover newer Intel
SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP version of the 8250 can actually use 1:1 serial8250_startup().
However it needs to be extended by a wake up irq which should to be
requested & enabled at ->startup() time and disabled at ->shutdown() time.
v2…v3: properly copy callbacks
v1…v2: add shutdown callback
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no way to access a struct uart_8250_port for a specific
line. This is only required outside of the 8250/uart callbacks like for
devices' suspend & remove callbacks. For those the 8250-core provides a
wrapper like serial8250_unregister_port() which passes the struct
to the proper function based on the line argument.
For run time suspend I need access to this struct not only to make
serial_out() work but also to properly restore up->ier and up->mcr.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many local variables were given the same name as a global. This
is valid, but generates many shadow warnings in W=2 builds. Resolve
them by changing the local names. Also change local variables
named "up" because they shadow the semaphore "up" function. Also
moved the outer declaration of the variable "a" because it is
only used in one block, and that resolves all of the shadow warnings
for the other declarations of "a" that have different types.
Change diacr => dia, kbd => kb, rep => rpt, up => udp.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code relies on the UART clock pre-divisor to be already
configured in the baud rate register. Calculate it in the driver
and set explicitly instead, also return the "real" effective baud
rate, which is generally slightly different from the requested value.
While at this, also ensure that break signal timing is updated when
baud rate changes.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds simple polling functions for single-character transmit
and receive, as used by kgdb.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer WonderMedia chips introduced another flag in the UART line control
register, which controls whether RTS/CTS signalling should be handled in
the driver or by the hardware itself.
This patch ensures that the kernel can control RTS/CTS (including
disabling it altogether) by forcing this flag to software mode on affected
chips (only WM8880 so far).
Also remove the redundant copy of the binding doc, while we are here.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present this console is optionally registered by NULL checking
arch_kgdb_ops.enable_nmi. In practice this requires the architecture
dependant code to implement some kind of control (e.g. module arguments)
to enable/disable this feature.
The kernel already provides us the perfectly adequate console= argument
to enable/disable consoles. Let's use that instead!
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Universally adopt container_of() for all pointer conversion from
uart_port to uart_amba_port.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking at the get_poll_char() function of the 8250.c serial driver,
we learn:
* poll_get_char() doesn't have to save/disable/restore the interrupt
registers. No interrupt handling is needed in this function at all.
Remove it.
* Don't block in case there is no data available. So instead blocking
in the do {} while loop, just return with NO_POLL_CHAR, immediately .
Additionally, while the i.MX6 register URXD[7-0] contain the RX_DATA,
the upper bits of this register (URXD[15-10]) might contain some
control flags. To ensure that these are not returned with the data
read, just mask out URXD[7-0].
These changes fix the 'hang' working with kdb:
$ echo ttymxc3 > /sys/module/kgdboc/parameters/kgdboc
$ echo g >/proc/sysrq-trigger
[0]kdb> help
...
<hang>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for spin lock assertion; move non-trivial assignment into
function body.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing callers of serial8250_modem_status() [1] hold the uart port
lock; document.
[1] In-tree callers of serial8250_modem_status()
drivers/tty/serial/8250/8250_fsl.c
fsl8250_handle_irq()
drivers/tty/serial/8250/8250_core.c
serial8250_handle_irq()
serial8250_console_write()
serial8250_get_mctrl() *
* Call graphs for callers of serial8250_get_mctrl() from the function
which acquires the uart port lock
drivers/tty/serial/serial_core.c
uart_port_startup()
uart_tiocmget()
uart_set_termios()
uart_carrier_raised()
ops->get_mctrl() ---> serial8250_get_mctrl()
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_SERIAL_BFIN_CTSRTS is set, compile fails because of missing
declarations for the gpio_* api. Include necessary header.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core may call the UART driver's start_tx() even if
tx is stopped; the UART driver must verify tx should be enabled
before transmitting.
Reported-by: Sam Ravnborg <sam@ravnborg.org>
cc: David S. Miller <davem@davemloft.net>
cc: <sparclinux@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mpc52xx_uart_send_xchar() is _identical_ to the default serial core
x_char handling behavior in uart_send_xchar().
Remove mpc52xx_uart_send_xchar().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
START_CHAR() & STOP_CHAR() can be disabled if set to '\0'
(__DISABLED_CHAR). UART drivers which define a send_xchar()
handler must not transmit __DISABLED_CHAR.
Document requirement.
Affected drivers:
sunsab
sunhv
cc: David S. Miller <davem@davemloft.net>
cc: <sparclinux@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_unthrottle() attempts to avoid sending START and the previous
x_char if the previous x_char has not yet been sent. However, this
optimization could leave the sender in a throttled state; for example,
if the sender is throttled and this unthrottle coincides with a manual
tcflow(TCION) from user-space, then neither START would be sent.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART driver is expected to clear port->x_char after
transmission while holding the port->lock. However, the serial
core fails to take the port->lock before assigning port->xchar.
This allows for the following race
CPU 0 | CPU 1
|
| serial8250_handle_irq
| ...
| serial8250_tx_chars
| if (port->x_char)
| serial_out(up, UART_TX, port->x_char)
uart_send_xchar |
port->x_char = ch |
| port->x_char = 0
port->ops->start_tx() |
|
The x_char on CPU 0 will never be sent.
Take the port->lock in uart_send_xchar() before assigning port->x_char.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core expects the UART driver to transmit x_char
(START/STOP chars) even if tx is stopped and before data already
in the tx ring buffer if possible. Also, sending x_char must
not cause additional data in the tx ring buffer to transmit
if tx is stopped.
Cause x_char to be transmitted before any other data is sent.
Auto-stop tx if the tx ring buffer is empty or tx should be stopped.
Only perform one write wakeup if tx ring buffer space is below
threshold.
x_char handling in DMA mode is still broken; add FIXME.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huang Shijie
Fugang Duan
Bryan O'Donoghue
Frans Klaver
Stefano Stabellini
Sebastian Andrzej Siewior
Peter Hurley
Alexander Shiyan
Greg Kroah-Hartman
Matthias Brugger
Daniel Thompson
Ricardo Ribalda Delgado
Lars-Peter Clausen
Richard Genoud
Alan Cox
Mark Rustad
Alexey Charkov
Dirk Behme