blk_revalidate_disk_zones() implements checks of the zones of a zoned
block device, verifying that the zone size is a power of 2 number of
sectors, that all zones (except possibly the last one) have the same
size and that zones cover the entire addressing space of the device.
While these checks are appropriate to verify that well tested hardware
devices have an adequate zone configurations, they lack in certain areas
which may result in issues with emulated devices implemented with user
drivers such as ublk or tcmu. Specifically, this function does not
check if the device driver indicated support for the mandatory zone
append writes, that is, if the device max_zone_append_sectors queue
limit is set to a non-zero value. Additionally, invalid zones such as
a zero length zone with a start sector equal to the device capacity will
not be detected and result in out of bounds use of the zone bitmaps
prepared with the callback function blk_revalidate_zone_cb().
Improve blk_revalidate_disk_zones() to address these inadequate checks,
relying on the fact that all device drivers supporting zoned block
devices must set the device zone size (chunk_sectors queue limit) and
the max_zone_append_sectors queue limit before executing this function.
The check for a non-zero max_zone_append_sectors value is done in
blk_revalidate_disk_zones() before executing the zone report. The zone
report callback function blk_revalidate_zone_cb() is also modified to
add a check that a zone start is below the device capacity.
The check that the zone size is a power of 2 number of sectors is moved
to blk_revalidate_disk_zones() as the zone size is already known.
Similarly, the number of zones of the device can be calculated in
blk_revalidate_disk_zones() before executing the zone report.
The kdoc comment for blk_revalidate_disk_zones() is also updated to
mention that device drivers must set the device zone size and the
max_zone_append_sectors queue limit before calling this function.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230703024812.76778-6-dlemoal@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The only overlap between the block open flags mapped into the fmode_t and
other uses of fmode_t are FMODE_READ and FMODE_WRITE. Define a new
blk_mode_t instead for use in blkdev_get_by_{dev,path}, ->open and
->ioctl and stop abusing fmode_t.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com> [rnbd]
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-28-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A few ioctl handlers have fmode_t arguments that are entirely unused,
remove them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20230608110258.189493-27-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce the function blk_rq_is_seq_zoned_write(). This function will
be used in later patches to preserve the order of zoned writes that
require write serialization.
This patch includes an optimization: instead of using
rq->q->disk->part0->bd_queue to check whether or not the queue is
associated with a zoned block device, use rq->q->disk->queue.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230517174230.897144-6-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove the blk_rq_is_passthrough() check because it is redundant:
blk_req_needs_zone_write_lock() also calls bdev_op_is_zoned_write()
and the latter function returns false for pass-through requests.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230517174230.897144-3-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bdev_get_queue() never returns NULL. Several commits [1][2] have been made
before to remove such superfluous checks, but some still remained.
For places where bdev_get_queue() is called solely for NULL checks, it is
removed entirely.
[1] commit ec9fd2a13d ("blk-lib: don't check bdev_get_queue() NULL check")
[2] commit fea127b36c ("block: remove superfluous check for request queue in bdev_is_zoned()")
Signed-off-by: Juhyung Park <qkrwngud825@gmail.com>
Reviewed-by: Pankaj Raghav <p.raghav@samsung.com>
Link: https://lore.kernel.org/r/20230203024029.48260-1-qkrwngud825@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of open coding to check for zone start, add a helper to improve
readability and store the logic in one place.
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230110143635.77300-3-p.raghav@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current implementation of blk_mq_plug() disables plugging for all
operations that involves a transfer to the device as we just check if
the last bit in op_is_write() function.
Modify blk_mq_plug() to disable plugging only for REQ_OP_WRITE and
REQ_OP_WRITE_ZEROS as they might require a zone lock.
Suggested-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220929074745.103073-2-p.raghav@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The type name enum req_opf is misleading since it suggests that values of
this type include both an operation type and flags. Since values of this
type represent an operation only, change the type name into enum req_op.
Convert the enum req_op documentation into kernel-doc format. Move a few
definitions such that the enum req_op documentation occurs just above
the enum req_op definition.
The name "req_opf" was introduced by commit ef295ecf09 ("block: better op
and flags encoding").
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-2-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the zone related fields that are currently stored in
struct request_queue to struct gendisk as these are part of the highlevel
block layer API and are only used for non-passthrough I/O that requires
the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-17-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the bdev based helpers instead of the queue based ones to clean up
the code a bit and prepare for storing all zone related fields in
struct gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-13-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a block_device instead of a request_queue as that is what most
callers have at hand.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch to a gendisk based API in preparation for moving all zone related
fields from the request_queue to the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch to a gendisk based API in preparation for moving all zone related
fields from the request_queue to the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use bdev_is_zoned in all places where a block_device is available instead
of open coding it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes. The high blast radius core update is the removal of
write same, which affects block and several non-SCSI devices. The
other big change, which is more local, is the removal of the SCSI
pointer.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYjzDQyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQMYAQDEWUGV
6U0+736AHVtOfiMNfiRN79B1HfXVoHvemnPcTwD/UlndwFfy/3GGOtoZmqEpc73J
Ec1HDuUCE18H1H2QAh0=
=/Ty9
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (qla2xxx, pm8001,
libsas, smartpqi, scsi_debug, lpfc, iscsi, mpi3mr) plus minor updates
and bug fixes.
The high blast radius core update is the removal of write same, which
affects block and several non-SCSI devices. The other big change,
which is more local, is the removal of the SCSI pointer"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (281 commits)
scsi: scsi_ioctl: Drop needless assignment in sg_io()
scsi: bsg: Drop needless assignment in scsi_bsg_sg_io_fn()
scsi: lpfc: Copyright updates for 14.2.0.0 patches
scsi: lpfc: Update lpfc version to 14.2.0.0
scsi: lpfc: SLI path split: Refactor BSG paths
scsi: lpfc: SLI path split: Refactor Abort paths
scsi: lpfc: SLI path split: Refactor SCSI paths
scsi: lpfc: SLI path split: Refactor CT paths
scsi: lpfc: SLI path split: Refactor misc ELS paths
scsi: lpfc: SLI path split: Refactor VMID paths
scsi: lpfc: SLI path split: Refactor FDISC paths
scsi: lpfc: SLI path split: Refactor LS_RJT paths
scsi: lpfc: SLI path split: Refactor LS_ACC paths
scsi: lpfc: SLI path split: Refactor the RSCN/SCR/RDF/EDC/FARPR paths
scsi: lpfc: SLI path split: Refactor PLOGI/PRLI/ADISC/LOGO paths
scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path
scsi: lpfc: SLI path split: Introduce lpfc_prep_wqe
scsi: lpfc: SLI path split: Refactor fast and slow paths to native SLI4
scsi: lpfc: SLI path split: Refactor lpfc_iocbq
scsi: lpfc: Use kcalloc()
...
No more users of REQ_OP_WRITE_SAME or drivers implementing it are left,
so remove the infrastructure.
[mkp: fold in and tweak sysfs reporting fix]
Link: https://lore.kernel.org/r/20220209082828.2629273-8-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass the block_device that we plan to use this bio for and the
operation to bio_init to optimize the assignment. A NULL block_device
can be passed, both for the passthrough case on a raw request_queue and
to temporarily avoid refactoring some nasty code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220124091107.642561-19-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All callers need to set the block_device and operation, so lift that into
the common code.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220124091107.642561-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When BLKRESETZONE ioctl and data read race, the data read leaves stale
page cache. The commit e511350590 ("block: Discard page cache of zone
reset target range") added page cache truncation to avoid stale page
cache after the ioctl. However, the stale page cache still can be read
during the reset zone operation for the ioctl. To avoid the stale page
cache completely, hold invalidate_lock of the block device file mapping.
Fixes: e511350590 ("block: Discard page cache of zone reset target range")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Cc: stable@vger.kernel.org # v5.15
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20211111085238.942492-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A user space process should not need the CAP_SYS_ADMIN capability set
in order to perform a BLKREPORTZONE ioctl.
Getting the zone report is required in order to get the write pointer.
Neither read() nor write() requires CAP_SYS_ADMIN, so it is reasonable
that a user space process that can read/write from/to the device, also
can get the write pointer. (Since e.g. writes have to be at the write
pointer.)
Fixes: 3ed05a987e ("blk-zoned: implement ioctls")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: stable@vger.kernel.org # v4.10+
Link: https://lore.kernel.org/r/20210811110505.29649-3-Niklas.Cassel@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Zone management send operations (BLKRESETZONE, BLKOPENZONE, BLKCLOSEZONE
and BLKFINISHZONE) should be allowed under the same permissions as write().
(write() does not require CAP_SYS_ADMIN).
Additionally, other ioctls like BLKSECDISCARD and BLKZEROOUT only check if
the fd was successfully opened with FMODE_WRITE.
(They do not require CAP_SYS_ADMIN).
Currently, zone management send operations require both CAP_SYS_ADMIN
and that the fd was successfully opened with FMODE_WRITE.
Remove the CAP_SYS_ADMIN requirement, so that zone management send
operations match the access control requirement of write(), BLKSECDISCARD
and BLKZEROOUT.
Fixes: 3ed05a987e ("blk-zoned: implement ioctls")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: stable@vger.kernel.org # v4.10+
Link: https://lore.kernel.org/r/20210811110505.29649-2-Niklas.Cassel@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
SCSI, ZNS and null_blk zoned devices support resetting all zones using
a single command (REQ_OP_ZONE_RESET_ALL), as indicated using the device
request queue flag QUEUE_FLAG_ZONE_RESETALL. This flag is not set for
device mapper targets creating zoned devices. In this case, a user
request for resetting all zones of a device is processed in
blkdev_zone_mgmt() by issuing a REQ_OP_ZONE_RESET operation for each
zone of the device. This leads to different behaviors of the
BLKRESETZONE ioctl() depending on the target device support for the
reset all operation. E.g.
blkzone reset /dev/sdX
will reset all zones of a SCSI device using a single command that will
ignore conventional, read-only or offline zones.
But a dm-linear device including conventional, read-only or offline
zones cannot be reset in the same manner as some of the single zone
reset operations issued by blkdev_zone_mgmt() will fail. E.g.:
blkzone reset /dev/dm-Y
blkzone: /dev/dm-0: BLKRESETZONE ioctl failed: Remote I/O error
To simplify applications and tools development, unify the behavior of
the all-zone reset operation by modifying blkdev_zone_mgmt() to not
issue a zone reset operation for conventional, read-only and offline
zones, thus mimicking what an actual reset-all device command does on a
device supporting REQ_OP_ZONE_RESET_ALL. This emulation is done using
the new function blkdev_zone_reset_all_emulated(). The zones needing a
reset are identified using a bitmap that is initialized using a zone
report. Since empty zones do not need a reset, also ignore these zones.
The function blkdev_zone_reset_all() is introduced for block devices
natively supporting reset all operations. blkdev_zone_mgmt() is modified
to call either function to execute an all zone reset request.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
[hch: split into multiple functions]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit e76239a374 ("block: add a report_zones method") removed the last
blk_zone_start() call. Hence also remove the definition of this function.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210406200820.15180-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When zone reset ioctl and data read race for a same zone on zoned block
devices, the data read leaves stale page cache even though the zone
reset ioctl zero clears all the zone data on the device. To avoid
non-zero data read from the stale page cache after zone reset, discard
page cache of reset target zones in blkdev_zone_mgmt_ioctl(). Introduce
the helper function blkdev_truncate_zone_range() to discard the page
cache. Ensure the page cache discarded by calling the helper function
before and after zone reset in same manner as fallocate does.
This patch can be applied back to the stable kernel version v5.10.y.
Rework is needed for older stable kernels.
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 3ed05a987e ("blk-zoned: implement ioctls")
Cc: <stable@vger.kernel.org> # 5.10+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210311072546.678999-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Similarly to a single zone reset operation (REQ_OP_ZONE_RESET), execute
REQ_OP_ZONE_RESET_ALL operations with REQ_SYNC set.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce the internal function blk_queue_clear_zone_settings() to
cleanup all limits and resources related to zoned block devices. This
new function is called from blk_queue_set_zoned() when a disk zoned
model is set to BLK_ZONED_NONE. This particular case can happens when a
partition is created on a host-aware scsi disk.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@edc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improves the checks on the zones of a zoned block device done in
blk_revalidate_disk_zones() by making sure that the device report_zones
method did report at least one zone and that the zones reported exactly
cover the entire disk capacity, that is, that there are no missing zones
at the end of the disk sector range.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When we loose a device for whatever reason while (re)scanning zones, we
trip over a NULL pointer in blk_revalidate_zone_cb, like in the following
log:
sd 0:0:0:0: [sda] 3418095616 4096-byte logical blocks: (14.0 TB/12.7 TiB)
sd 0:0:0:0: [sda] 52156 zones of 65536 logical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 37 00 00 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] REPORT ZONES start lba 1065287680 failed
sd 0:0:0:0: [sda] REPORT ZONES: Result: hostbyte=0x00 driverbyte=0x08
sd 0:0:0:0: [sda] Sense Key : 0xb [current]
sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x6
sda: failed to revalidate zones
sd 0:0:0:0: [sda] 0 4096-byte logical blocks: (0 B/0 B)
sda: detected capacity change from 14000519643136 to 0
==================================================================
BUG: KASAN: null-ptr-deref in blk_revalidate_zone_cb+0x1b7/0x550
Write of size 8 at addr 0000000000000010 by task kworker/u4:1/58
CPU: 1 PID: 58 Comm: kworker/u4:1 Not tainted 5.8.0-rc1 #692
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4-rebuilt.opensuse.org 04/01/2014
Workqueue: events_unbound async_run_entry_fn
Call Trace:
dump_stack+0x7d/0xb0
? blk_revalidate_zone_cb+0x1b7/0x550
kasan_report.cold+0x5/0x37
? blk_revalidate_zone_cb+0x1b7/0x550
check_memory_region+0x145/0x1a0
blk_revalidate_zone_cb+0x1b7/0x550
sd_zbc_parse_report+0x1f1/0x370
? blk_req_zone_write_trylock+0x200/0x200
? sectors_to_logical+0x60/0x60
? blk_req_zone_write_trylock+0x200/0x200
? blk_req_zone_write_trylock+0x200/0x200
sd_zbc_report_zones+0x3c4/0x5e0
? sd_dif_config_host+0x500/0x500
blk_revalidate_disk_zones+0x231/0x44d
? _raw_write_lock_irqsave+0xb0/0xb0
? blk_queue_free_zone_bitmaps+0xd0/0xd0
sd_zbc_read_zones+0x8cf/0x11a0
sd_revalidate_disk+0x305c/0x64e0
? __device_add_disk+0x776/0xf20
? read_capacity_16.part.0+0x1080/0x1080
? blk_alloc_devt+0x250/0x250
? create_object.isra.0+0x595/0xa20
? kasan_unpoison_shadow+0x33/0x40
sd_probe+0x8dc/0xcd2
really_probe+0x20e/0xaf0
__driver_attach_async_helper+0x249/0x2d0
async_run_entry_fn+0xbe/0x560
process_one_work+0x764/0x1290
? _raw_read_unlock_irqrestore+0x30/0x30
worker_thread+0x598/0x12f0
? __kthread_parkme+0xc6/0x1b0
? schedule+0xed/0x2c0
? process_one_work+0x1290/0x1290
kthread+0x36b/0x440
? kthread_create_worker_on_cpu+0xa0/0xa0
ret_from_fork+0x22/0x30
==================================================================
When the device is already gone we end up with the following scenario:
The device's capacity is 0 and thus the number of zones will be 0 as well. When
allocating the bitmap for the conventional zones, we then trip over a NULL
pointer.
So if we encounter a zoned block device with a 0 capacity, don't dare to
revalidate the zones sizes.
Fixes: 6c6b354914 ("block: set the zone size in blk_revalidate_disk_zones atomically")
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the zoned storage model, the sectors within a zone are typically all
writeable. With the introduction of the Zoned Namespace (ZNS) Command
Set in the NVM Express organization, the model was extended to have a
specific writeable capacity.
Extend the zone descriptor data structure with a zone capacity field to
indicate to the user how many sectors in a zone are writeable.
Introduce backward compatibility in the zone report ioctl by extending
the zone report header data structure with a flags field to indicate if
the capacity field is available.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Modify the interface of blk_revalidate_disk_zones() to add an optional
driver callback function that a driver can use to extend processing
done during zone revalidation. The callback, if defined, is executed
with the device request queue frozen, after all zones have been
inspected.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce blk_req_zone_write_trylock(), which either grabs the write-lock
for a sequential zone or returns false, if the zone is already locked.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a helper to stringify the zone conditions. We use this helper in the
next patch to track zone conditions in tracepoints.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the current implementation, final zone-mgmt request is issued with
submit_bio_wait() which marks the bio REQ_SYNC. This is needed since
immediate action is expected for zone-mgmt requests as these are
blocking operations. This also bypasses the scheduler in the
blk_mq_make_request() and dispatches the request directly into the
hw ctx.
This patch marks all the chained bios REQ_SYNC so that we can have
above-mentioned behavior for non-final bios also.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current zone revalidation code has a major problem in that it
doesn't update the zone size and q->nr_zones atomically, leading
to a short window where an out of bounds access to the zone arrays
is possible.
To fix this move the setting of the zone size into the crticial
sections blk_revalidate_disk_zones so that it gets updated together
with the zone bitmaps and q->nr_zones. This also slightly simplifies
the caller as it deducts the zone size from the report_zones.
This change also allows to check for a power of two zone size in generic
code.
Reported-by: Hans Holmberg <hans@owltronix.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio based drivers only need to update q->nr_zones. Do that manually
instead of overloading blk_revalidate_disk_zones to keep that function
simpler for the next round of changes that will rely even more on the
request based functionality.
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Allocate the conventional zone bitmap and the sequential zone locking
bitmap only when we find a zone of the respective type. This avoids
wasting memory on the conventional zone bitmap for devices that only
have sequential zones, and will also prepare for other future changes.
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Invert the meaning of seq_zones_bitmap by keeping a bitmap of
conventional zones. This allows not having a bitmap for devices
that do not have conventional zones.
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Simplify the arguments to blkdev_nr_zones by passing a gendisk instead
of the block_device and capacity. This also removes the need for
__blkdev_nr_zones as all callers are outside the fast path and can
deal with the additional branch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Avoid the need to allocate a potentially large array of struct blk_zone
in the block layer by switching the ->report_zones method interface to
a callback model. Now the caller simply supplies a callback that is
executed on each reported zone, and private data for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No known partitioning tool supports zoned block devices, especially the
host managed flavor with strong sequential write constraints.
Furthermore, there are also no known user nor use cases for partitioned
zoned block devices.
This patch removes partition device creation for zoned block devices,
which allows simplifying the processing of zone commands for zoned
block devices. A warning is added if a partition table is found on the
device.
For report zones operations no zone sector information remapping is
necessary anymore, simplifying the code. Of note is that remapping of
zone reports for DM targets is still necessary as done by
dm_remap_zone_report().
Similarly, remaping of a zone reset bio is not necessary anymore.
Testing for the applicability of the zone reset all request also becomes
simpler and only needs to check that the number of sectors of the
requested zone range is equal to the disk capacity.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All kernel users of blkdev_report_zones() as well as applications use
through ioctl(BLKZONEREPORT) expect to potentially get less zone
descriptors than requested. As such, the use of the internal report
zones command execution loop implemented by blk_report_zones() is
not necessary and can even be harmful to performance by causing the
execution of inefficient small zones report command to service the
reminder of a requested zone array.
This patch removes blk_report_zones(), simplifying the code. Also
remove a now incorrect comment in dm_blk_report_zones().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Javier Gonzalez <javier@javigon.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_revalidate_disk_zones is never called for non-zoned devices. Just
return early and warn instead of trying to handle this case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For ZBC and ZAC zoned devices, the scsi driver revalidation processing
implemented by sd_revalidate_disk() includes a call to
sd_zbc_read_zones() which executes a full disk zone report used to
check that all zones of the disk are the same size. This processing is
followed by a call to blk_revalidate_disk_zones(), used to initialize
the device request queue zone bitmaps (zone type and zone write lock
bitmaps). To do so, blk_revalidate_disk_zones() also executes a full
device zone report to obtain zone types. As a result, the entire
zoned block device revalidation process includes two full device zone
report.
By moving the zone size checks into blk_revalidate_disk_zones(), this
process can be optimized to a single full device zone report, leading to
shorter device scan and revalidation times. This patch implements this
optimization, reducing the original full device zone report implemented
in sd_zbc_check_zones() to a single, small, report zones command
execution to obtain the size of the first zone of the device. Checks
whether all zones of the device are the same size as the first zone
size are moved to the generic blk_check_zone() function called from
blk_revalidate_disk_zones().
This optimization also has the following benefits:
1) fewer memory allocations in the scsi layer during disk revalidation
as the potentailly large buffer for zone report execution is not
needed.
2) Implement zone checks in a generic manner, reducing the burden on
device driver which only need to obtain the zone size and check that
this size is a power of 2 number of LBAs. Any new type of zoned
block device will benefit from this.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce three new ioctl commands BLKOPENZONE, BLKCLOSEZONE and
BLKFINISHZONE to allow applications to control the condition of zones
on a zoned block device through the execution of the REQ_OP_ZONE_OPEN,
REQ_OP_ZONE_CLOSE and REQ_OP_ZONE_FINISH operations.
Contains contributions from Matias Bjorling, Hans Holmberg,
Dmitry Fomichev, Keith Busch, Damien Le Moal and Christoph Hellwig.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Matias Bjorling <matias.bjorling@wdc.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Zoned block devices (ZBC and ZAC devices) allow an explicit control
over the condition (state) of zones. The operations allowed are:
* Open a zone: Transition to open condition to indicate that a zone will
actively be written
* Close a zone: Transition to closed condition to release the drive
resources used for writing to a zone
* Finish a zone: Transition an open or closed zone to the full
condition to prevent write operations
To enable this control for in-kernel zoned block device users, define
the new request operations REQ_OP_ZONE_OPEN, REQ_OP_ZONE_CLOSE
and REQ_OP_ZONE_FINISH as well as the generic function
blkdev_zone_mgmt() for submitting these operations on a range of zones.
This results in blkdev_reset_zones() removal and replacement with this
new zone magement function. Users of blkdev_reset_zones() (f2fs and
dm-zoned) are updated accordingly.
Contains contributions from Matias Bjorling, Hans Holmberg,
Dmitry Fomichev, Keith Busch, Damien Le Moal and Christoph Hellwig.
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Matias Bjorling <matias.bjorling@wdc.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Martin K. Petersen
Damien Le Moal
Christoph Hellwig
Bart Van Assche
Juhyung Park
Pankaj Raghav
Linus Torvalds
Chaitanya Kulkarni
Shin'ichiro Kawasaki
Niklas Cassel
Damien Le Moal
Johannes Thumshirn
Matias Bjørling
Chaitanya Kulkarni
Alexey Dobriyan
Ajay Joshi