There is a race condition between rds_send_xmit -> rds_tcp_xmit
and the code that deals with resolution of duelling syns added
by commit 241b271952 ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()").
Specifically, we may end up derefencing a null pointer in rds_send_xmit
if we have the interleaving sequence:
rds_tcp_accept_one rds_send_xmit
conn is RDS_CONN_UP, so
invoke rds_tcp_xmit
tc = conn->c_transport_data
rds_tcp_restore_callbacks
/* reset t_sock */
null ptr deref from tc->t_sock
The race condition can be avoided without adding the overhead of
additional locking in the xmit path: have rds_tcp_accept_one wait
for rds_tcp_xmit threads to complete before resetting callbacks.
The synchronization can be done in the same manner as rds_conn_shutdown().
First set the rds_conn_state to something other than RDS_CONN_UP
(so that new threads cannot get into rds_tcp_xmit()), then wait for
RDS_IN_XMIT to be cleared in the conn->c_flags indicating that any
threads in rds_tcp_xmit are done.
Fixes: 241b271952 ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hosts sending lot of ACK packets exhibit high sock_wfree() cost
because of cache line miss to test SOCK_USE_WRITE_QUEUE
We could move this flag close to sk_wmem_alloc but it is better
to perform the atomic_sub_and_test() on a clean cache line,
as it avoid one extra bus transaction.
skb_orphan_partial() can also have a fast track for packets that either
are TCP acks, or already went through another skb_orphan_partial()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Fixes for tunnel checksum and segmentation offloads
This patch series is a subset of patches I had submitted for net-next. I
plan to drop these two patches from the v3 of "Fix Tunnel features and
enable GSO partial for several drivers" and I am instead submitting them
for net since these are truly fixes and likely will need to be backported
to stable branches.
This series addresses 2 specific issues. The first is that we could
request TSO on a v4 inner header while not supporting checksum offload of
the outer IPv6 header. The second is that we could request an IPv6 inner
checksum offload without validating that we could actually support an inner
IPv6 checksum offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to perform an additional check on the inner headers to determine if
we can offload the checksum for them. Previously this check didn't occur
so we would generate an invalid frame in the case of an IPv6 header
encapsulated inside of an IPv4 tunnel. To fix this I added a secondary
check to vxlan_features_check so that we can verify that we can offload the
inner checksum.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of the mlx4 and mlx5 driver they do not support IPv6 checksum
offload for tunnels. With this being the case we should disable GSO in
addition to the checksum offload features when we find that a device cannot
perform a checksum on a given packet type.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: redesign socket-level flow control
The socket-level flow control in TIPC has long been due for a major
overhaul. This series fixes this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two flow control mechanisms in TIPC; one at link level that
handles network congestion, burst control, and retransmission, and one
at connection level which' only remaining task is to prevent overflow
in the receiving socket buffer. In TIPC, the latter task has to be
solved end-to-end because messages can not be thrown away once they
have been accepted and delivered upwards from the link layer, i.e, we
can never permit the receive buffer to overflow.
Currently, this algorithm is message based. A counter in the receiving
socket keeps track of number of consumed messages, and sends a dedicated
acknowledge message back to the sender for each 256 consumed message.
A counter at the sending end keeps track of the sent, not yet
acknowledged messages, and blocks the sender if this number ever reaches
512 unacknowledged messages. When the missing acknowledge arrives, the
socket is then woken up for renewed transmission. This works well for
keeping the message flow running, as it almost never happens that a
sender socket is blocked this way.
A problem with the current mechanism is that it potentially is very
memory consuming. Since we don't distinguish between small and large
messages, we have to dimension the socket receive buffer according
to a worst-case of both. I.e., the window size must be chosen large
enough to sustain a reasonable throughput even for the smallest
messages, while we must still consider a scenario where all messages
are of maximum size. Hence, the current fix window size of 512 messages
and a maximum message size of 66k results in a receive buffer of 66 MB
when truesize(66k) = 131k is taken into account. It is possible to do
much better.
This commit introduces an algorithm where we instead use 1024-byte
blocks as base unit. This unit, always rounded upwards from the
actual message size, is used when we advertise windows as well as when
we count and acknowledge transmitted data. The advertised window is
based on the configured receive buffer size in such a way that even
the worst-case truesize/msgsize ratio always is covered. Since the
smallest possible message size (from a flow control viewpoint) now is
1024 bytes, we can safely assume this ratio to be less than four, which
is the value we are now using.
This way, we have been able to reduce the default receive buffer size
from 66 MB to 2 MB with maintained performance.
In order to keep this solution backwards compatible, we introduce a
new capability bit in the discovery protocol, and use this throughout
the message sending/reception path to always select the right unit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During neighbor discovery, nodes advertise their capabilities as a bit
map in a dedicated 16-bit field in the discovery message header. This
bit map has so far only be stored in the node structure on the peer
nodes, but we now see the need to keep a copy even in the socket
structure.
This commit adds this functionality.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the refactoring commit d570d86497 ("tipc: enqueue arrived buffers
in socket in separate function") we did by accident replace the test
if (sk->sk_backlog.len == 0)
atomic_set(&tsk->dupl_rcvcnt, 0);
with
if (sk->sk_backlog.len)
atomic_set(&tsk->dupl_rcvcnt, 0);
This effectively disables the compensation we have for the double
receive buffer accounting that occurs temporarily when buffers are
moved from the backlog to the socket receive queue. Until now, this
has gone unnoticed because of the large receive buffer limits we are
applying, but becomes indispensable when we reduce this buffer limit
later in this series.
We now fix this by inverting the mentioned condition.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure and enable various tunnels on the
adapter after PF start.
This change was missed as a part of
'commit 464f664501
("qed: Add infrastructure support for tunneling")'
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3b9d6da67e ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.
Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joachim Eastwood says:
====================
stmmac: dwmac-socfpga refactor+cleanup
This patch aims to remove the init/exit callbacks from the dwmac-
socfpga driver and instead use standard PM callbacks. Doing this
will also allow us to cleanup the driver.
Eventually the init/exit callbacks will be deprecated and removed
from all drivers dwmac-* except for dwmac-generic. Drivers will be
refactored to use standard PM and remove callbacks.
This patch set should not change the behavior of the driver itself,
it only moves code around. The only exception to this is patch
number 4 which restores the resume callback behavior which was
changed in the "net: stmmac: socfpga: Remove re-registration of
reset controller" patch. I belive calling phy_resume() only
from the resume callback and not probe is the right thing to do.
Changes from v1:
- Rebase on net-next
One heads-up here:
The first patch changes the prototype of a couple of
functions used in Alexandre's "add Ethernet glue logic for
stm32 chip" patch [1] and will cause build failures for
dwmac-stm32.c if not fixed up!
If Alexandre's patch set is applied first I will gladly
rebase my patch set to account for his driver as well.
[1] https://patchwork.ozlabs.org/patch/614405/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove old init callback which now contains only a call to
socfpga_dwmac_setup(). Also rename socfpga_dwmac_setup() to indicate
what the function really does.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_resume() should only be need during driver resume to
workaround a hardware errata.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-socfpga driver needs to control the reset usually managed
by the core driver to set the PHY mode. Take a copy of the reset
handle from core priv data so it can be used by the driver later.
This also allow us to move reset handling into socfpga_dwmac_setup()
where the code that needs it is located.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the needed PM callbacks in the driver instead of
relying on the init/exit hooks in stmmac_platform. This gives
the driver more flexibility in how the code is organized.
Eventually the init/exit callbacks will be deprecated in favor
of the standard PM callbacks and driver remove function.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change stmmac_remove/resume/suspend to take a device pointer so
they can be used directly by drivers that doesn't need to perform
anything device specific.
This lets us remove the PCI pm functions and later simplifiy the
platform drivers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now mdiobus_scan() returns ERR_PTR(-ENODEV) instead of NULL if the PHY
device ID was read as all ones. As this was not an error before, this
value should be filtered out now in this driver.
Fixes: b74766a0a0 ("phylib: don't return NULL from get_phy_device()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mdiobus_scan() returns either an error code or NULL on error, the
driver should check for both, not only for NULL, otherwise a crash is
imminent...
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_iv_ogm_orig_del_if handles two different buffers bcast_own and
bcast_own_sum which should be resized. The error handling two for
allocating these buffers causes the complexity of this function. This can
be avoided completely when the function is split into a main function
handling the locking, freeing and call of the subfunctions.
The subfunction can then independently handle the resize of the buffers.
This also allows to easily reuse the old buffer (which always is larger) in
case a smaller buffer could not be allocated without increasing the code
complexity.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Since batadv_v_ogm_orig_update() was only called from one place and the
calling function became very short, merge these two functions together.
This should also reflect the protocol description of B.A.T.M.A.N. V
better.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
To match our code better to the protocol description of B.A.T.M.A.N. V,
move batadv_v_ogm_forward() out into batadv_v_ogm_process_per_outif()
and move all checks directly deciding whether the OGM should be
forwarded into batadv_v_ogm_forward().
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Structure initialization within the macros should follow the general
coding style used in the kernel: put the initialization of the first
variable and the closing brace on a separate line.
Reported-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <simon.wunderlich@open-mesh.com>
[sven@narfation.org: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Some really long function names in batman-adv require a newline between
return type and the function name. This has lead to some lines starting
with *batadv_...
This * belongs to the return type and thus should be on the same line as
the return type.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
checkpatch.pl warns about the use of 'unsigned' as a short form for
'unsigned int'.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Use a static string when showing table headers rather then
a nonsense parametric one with fixed arguments.
It is easier to grep and it does not need to be recomputed
at runtime each time.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
[sven@narfation.org: fix conflicts with current version]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The sysfs ABI documentation files and the batman-adv.txt are maintained by
the BATMAN ADVANCED maintainers and patches for them should therefore be
sent to them.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The mailing list of b.a.t.m.a.n@lists.open-mesh.org is moderated for
non-subscribers and non-whitelisted addresses. Such mails will be delayed
but the sender will not be informed about the moderation.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Pull HID fixes from Jiri Kosina:
"Fixes for the HID subsystem:
- regression fix for Wacom driver; commit introduced in 4.6-rc1
mistakenly removed line that should be kept. Fix by Ping Cheng
- two device-specific quirks, by Ping Cheng and Nazar Mokrynskyi"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: add missed stylus_in_proximity line back
HID: Fix boot delay for Creative SB Omni Surround 5.1 with quirk
HID: wacom: Add support for DTK-1651
failures and division by zeros in the kernel on those devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BKj3
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One small bug fix for the imx6qp CAN clk definition that was causing
failures and division by zeros in the kernel on those devices"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx6q: fix typo in CAN clock definition
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes for 4.6-rc
This small series provides some bug fixes for mlx5 driver.
A small bug fix for iounmap of a null pointer, which dumps a warning on some archs.
One patch to fix the VXLAN/MLX5_EN dependency issue reported by Arnd.
Two patches to fix the scheduling while atomic issue for ndo_add/del_vxlan_port
NDOs. The first will add an internal mlx5e workqueue and the second will
delegate vxlan ports add/del requests to that workqueue.
Note: ('net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue') is only needed for net
and not net-next as the issue was globally fixed for all device drivers by:
b7aade1548 ('vxlan: break dependency with netdev drivers') in net-next.
Applied on top: f27337e16f ('ip_tunnel: fix preempt warning in ip tunnel creation/updating')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The vxlan add/delete port NDOs are called under rcu lock.
The current mlx5e implementation can potentially block in these
calls, which is not allowed. Move to using the mlx5e workqueue
to handle these NDOs.
Fixes: b3f63c3d5e ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a mlx5e workqueue to handle all mlx5e specific tasks. Move
all tasks currently using the system workqueue to the new workqueue.
This is in preparation for vxlan using the mlx5e workqueue in order to
schedule port add/remove operations.
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When MLX5_EN=y MLX5_CORE=y and VXLAN=m there is a linker error for
vxlan_get_rx_port() due to the fact that VXLAN is a module. Change Kconfig
to select VXLAN when MLX5_CORE=y. When MLX5_CORE=m there is no dependency
on the value of VXLAN.
Fixes: b3f63c3d5e ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When freeing UAR the driver tries to unmap uar->map and uar->bf_map
which are mutually exclusive thus always unmapping a NULL pointer.
Make sure we only call iounmap() once, for the actual mapping.
Fixes: 0ba422410b ('net/mlx5: Fix global UAR mapping')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reported-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fec_mpc52xx driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fs-enet driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the ucc driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the gianfar driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan
Eric Dumazet
David S. Miller
Alexander Duyck
Jon Paul Maloy
Oliver Neukum
Manish Chopra
Anna-Maria Gleixner
Joachim Eastwood
Sergei Shtylyov
Alex Deucher
Sven Eckelmann
Simon Wunderlich
Simon Wunderlich
Antonio Quartulli
Geliang Tang
Simon Wunderlich
Linus Torvalds
Matthew Finlay
Gal Pressman
Philippe Reynes