The function “platform_get_irq” can log an error already.
Thus omit redundant messages for the exception handling in the
calling functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/05f49ae7-5cc7-d6a0-fc3d-abaf2a0b373c@web.de
The spinlock pkg_temp_lock has the potential of being taken in atomic
context because it can be acquired from the thermal IRQ vector.
It's static and limited scope so go ahead and make it a raw spinlock.
Signed-off-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191008110021.2j44ayunal7fkb7i@linutronix.de
With the STM32 thermal peripheral, it is not possible to dump the
temperature that has caused the interrupt.
When the temperature reaches the low threshold, we generally read
a temperature that is a little bit higher than the low threshold.
This maybe due to sampling precision, and also because the CPU becomes
hotter when it quits WFI mode.
In that case, the framework does not change the trip points. This leads
to a lot of low threshold interrupts.
The fix is to set the low threshold value 0.5 degrees Celsius
below the actual request.
The problem is not so frequent with the high threshold and it would
no be a good idea to set the threshold value higher than the request.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-7-p.paillet@st.com
Change the way of computing to avoid rounds by 1 or 2 degrees.
Also simplify the sampling time management that is hard-coded
to maximum value during probe.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-6-p.paillet@st.com
Let the thermal framework handle the trip points instead
of custom code inside the driver. This is backward compatible,
simplifies the driver and offers the possibility to the user
to set any trip point he needs.
stm_thermal_set_trips callback that is registered to
set_trips ops to handle the low and high thresholds and replaces
stm_thermal_set_threshold and stm_thermal_update_threshold functions.
modify irq enable to handle the thresholds.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-5-p.paillet@st.com
In case of CPU reset, the interrupts could be enabled at boot time.
Disable interrupts and clear flags.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-4-p.paillet@st.com
Be sure get_temp returns an error while disabling or enabling the device.
Set THERMAL_DEVICE_ENABLED state at the end of power on function.
Set THERMAL_DEVICE_DISABLED state at the beginning of power off function.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200110101605.24984-3-p.paillet@st.com
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Adding brackets allows to multiply the register value,
masked by TS1_RAMP_COEFF_MASK, by an ADJUST value
properly and not to multiply ADJUST by register value and
then mask the whole.
Fixes: 1d693155 ("thermal: add stm32 thermal driver")
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: David Hernandez Sanchez <david.hernandezsanchez@st.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Calling stm_thermal_read_factory_settings before clocking
internal peripheral causes bad register values and makes
temperature computation wrong.
Calling stm_thermal_read_factory_settings inside
stm_thermal_prepare fixes this problem as internal
peripheral is well clocked at this stage.
Fixes: 1d693155 ("thermal: add stm32 thermal driver")
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: David Hernandez Sanchez <david.hernandezsanchez@st.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for DTS thermal sensor that can be
found on some STM32 platforms.
This driver is based on OF and works in interrupt
mode.
It offers two temperature trip points:
passive and critical. The first is intended for
passive cooling notification while the second is
used for over-temperature reset.
Signed-off-by: David Hernandez Sanchez <david.hernandezsanchez@st.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Markus Elfring
Clark Williams
Colin Ian King
Pascal Paillet
Wolfram Sang
David HERNANDEZ SANCHEZ