Our charger manager can optimize the battery capacity periodically, so
we can save last battery capacity into registers. Then next system
power-on, we can read the last saved battery capacity as the initial
battery capacity, which can make the battery capacity more accurate.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Move SHDWC realted data to only one structure to have them grouped.
Inspired from commit 9be74f0d39 ("power: reset: at91-poweroff: make
mpddrc_base part of struct shdwc").
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add fuel gauge platform suspend and resume interfaces. In suspend state,
we should enable the low voltage and coulomb counter threshold interrupts
to wake up system to calibrate the battery capacity in lower voltage stage.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add low voltage alarm support to make sure the battery capacity
more accurate in lower voltage stage.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds support to read calibration values from the eFuse controller
to calibrate the ADC values corresponding to current and voltage, which can
make the current and voltage data more accurate.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Free battery information in case of adding battery OCV tables.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add info->charging validation to avoid repeated charge or discharge
operation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The USB charger status can be notified before the charger driver registers
the USB phy notifier, so we should check the charger status in probe() in
case we missed the USB charger notification.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the USB notifier context is atomic, we can not start or stop charging
in atomic context. Thus this patch adds one work to help to charge or
discharge.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove at91_ramc_of_match[] since it is not used anywhere in this code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use only one poweroff function and adapt it to work for both scenarios
(with LPDDR or not). The assignement of pm_power_off was moved at the
end of probe after all initializations are OK. This patch adapt the idea
from commit 4e018c1e9b ("power: reset: at91-poweroff: use only one
poweroff function").
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq24196 is another variant of the bq24190 charger ic.
Its register set is identical to the bq24192 and it even reuses
the same part number (0x5).
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add extcon support so that we can notify USB drivers of cable state
changes. Based on work from Jonathan Marek. USB OTG was tested on a LG
Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds an of_match for the usb-otg-vbus regulator to
bq24190_charger.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds support for the bq24192 variant to bq24190_charger.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: Changed if statement to a switch based on
feedback from Sebastian Reichel.]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Switch the SI to boot mode so on a warm reboot, the SI is able to access
the flash.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Similar to gpio-reset allow to specify active and inactive delays
while keeping the 100ms defaults that were used previously all the time.
The dt-properties are named the same as in gpio-reset but get an "-ms"
suffix as properties should contain such a suffix specifying its unit.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Trivial fix to clean up indentation issue, remove an extraneous tab
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=FoKv
-----END PGP SIGNATURE-----
Merge tag 'psy-mfd-axp813-immutable-for-v4.21-signed' into psy-next
Immutable branch between mfd and power-supply for driver
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
AXP813 and AXP803 PMICs can control input current and minimum voltage.
Both of these values are configurable.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make use of the recommended BIT() macro for bit defines.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The axp20x_usb_power driver uses BIT() operations but lacks the include
for it. Include the bitops.h header file.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't populate the array cpcap_battery_irqs on the stack but instead
make it static. Makes the object code smaller by 99 bytes:
Before:
text data bss dec hex filename
13673 2448 0 16121 3ef9 cpcap-battery.o
After:
text data bss dec hex filename
13510 2512 0 16022 3e96 cpcap-battery.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
According to [1] and [2], the temperature values are in tenths of degree
Celsius. Exposing the Celsius value makes the battery appear on fire:
$ upower -i /org/freedesktop/UPower/devices/battery_olpc_battery
...
temperature: 236.9 degrees C
Tested on OLPC XO-1 and OLPC XO-1.75 laptops.
[1] include/linux/power_supply.h
[2] Documentation/power/power_supply_class.txt
Fixes: fb972873a7 ("[BATTERY] One Laptop Per Child power/battery driver")
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix build errors when FUEL_GUAGE_SC27XX is enabled but IIO is either
not enabled or IIO=m and FUEL_GUAGE_SC27XX=y.
ld: drivers/power/supply/sc27xx_fuel_gauge.o: in function `sc27xx_fgu_get_temp':
sc27xx_fuel_gauge.c:(.text+0x1d2): undefined reference to `iio_read_channel_processed'
ld: drivers/power/supply/sc27xx_fuel_gauge.o: in function `sc27xx_fgu_probe':
sc27xx_fuel_gauge.c:(.text+0x97f): undefined reference to `devm_iio_channel_get'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-pm@vger.kernel.org
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the Spreadtrum SC27XX serial PMICs fuel gauge support,
which is used to calculate the battery capacity.
Original-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We have introduced some battery properties to present the OCV table
temperatures and OCV capacity table values. Thus this patch add OCV
temperature and OCV table for battery information, as well as providing
some helper functions to use the OCV capacity table for users.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add one field for 'struct power_supply_battery_info' to present the battery
factory internal resistance.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Use the new of_get_compatible_child() helper to lookup the usb sibling
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(non-sibling) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the parent device node).
While at it, also fix the related phy-node reference leak.
Fixes: f5e4edb8c8 ("power: twl4030_charger: find associated phy by more reliable means.")
Cc: stable <stable@vger.kernel.org> # 4.2
Cc: NeilBrown <neilb@suse.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 201510 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Trivial fix to spelling mistake in MODULE_DESCRIPTION text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
omap_sr_register_pmic() was introduced in 2010 in commit
984aa6dbf4 ("OMAP3: PM: Adding smartreflex driver support.")
. There was never any caller of this function in mainline resulting in a
warning
sr_init: No PMIC hook to init smartreflex
for each machine where this driver is enabled. So remove the unused
function and the pr_warn.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the binding and driver for pms405 pon.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
According to the datasheet, bq27411 is similar to bq27421.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the SC2731 PMIC switch charger support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This avoids getting woken up from suspend after power interruptions
when the bci wrongly thinks the battery is full just because
of input current going low because of low input power
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
the charging current uses unsigned int variables, if we step back
if the current is still low, we would run into negative which
means setting the target to a huge value.
Better add checks here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Immutable branch between mfd and power-supply for driver
changes in CROS USBPD charger driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=ya3t
-----END PGP SIGNATURE-----
Merge tag 'psy-mfd-cros-immutable-for-v4.20-signed' into psy-next
Immutable branch for mfd and power-supply for v4.20
Immutable branch between mfd and power-supply for driver
changes in CROS USBPD charger driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
ChromeOS devices can have one optional dedicated port.
The Dedicated port is unique and similar to the USB PD ports
except that it doesn't support as many properties.
The presence of a dedicated port is determined from whether the
EC's charger port count is equal to 'number of USB PD port' + 1.
The dedicated port ID is always the last valid port ID.
This commit keeps compatibility with Embedded Controllers that do not
support the new EC_CMD_CHARGE_PORT_COUNT command by setting
the number of charger port to be equal to the number of USB PD port
when this command fails.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Immutable branch between mach-at91 and power-supply for driver
changes in at91-poweroff.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=n/Lz
-----END PGP SIGNATURE-----
Merge tag 'psy-at91-poweroff-immutable-for-v4.20-signed' into psy-next
Immutable branch for mach-at91 and power-supply for v4.20
Immutable branch between mach-at91 and power-supply for driver
changes in at91-poweroff.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There should be only one instance of struct shdwc in the system. This is
referenced through at91_shdwc. Return in probe if at91_shdwc is already
allocated.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rename at91_shdwc_base member of struct shdwc to shdwc_base. There is
already an "at91" string in at91_shdwc object.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make sclk part of struct shdwc to have all the data specific to SHDWC
grouped together in one structure.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make mpddrc_base part of struct shdwc since there is also only one
instance of struct shdwc *at91_shdwc in system and to have all data
specific to SHDWC grouped together.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use only one poweroff function for sama5d2 and adapt it to work for both
scenarios (having LPDDR or not).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SAMA5D2 NRST input signal is resynchronized with the SLCK clock and it
can take up to 2 SLCK cycles (about 90us) for the internal reset to be
effective. During this delay, the VDDCORE current consumption may still be
high (application-dependent) with the VDDCORE regulator already OFF. Under
such conditions, VDDCORE may operate below its operating range leading to
potential register corruption.
To prevent such situation, it is recommended to decrease significantly the
power consumption of the device once the voltage regulator is turned-off.
This can be achieved by operating the device at a much lower low frequency.
To solve this switch the master clock to slock clock just before writing
shutdown command to shutdown controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Suggested-by: Patrice Vilchez <patrice.vilchez@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If kstrtoul() fails then we print "charge_full" when it's uninitialized.
The debug printk doesn't add anything so I deleted it and cleaned these
two functions up a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This adds rate limiting to the message that is printed when reading a
power supply property via sysfs returns an error. This will prevent
userspace applications from unintentionally dDOSing the system by
continuously reading a property that returns an error.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ2589x family has the capability of reading the current battery voltage.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ25896 is almost identical to the BQ25890.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are a few table entries that aren't used. Drop them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
To ease adding a new part variant some debugging is handy.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
simple_strtoul is obsolete, and use kstrtoint instead
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pointer 'dev' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The URL of bq27441-g1 and bq27426 are missing and bq27520-g4 is duplicated.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
It seems that a *break* is missing in order to avoid a fall-through.
Otherwise, the calculation of *data* makes no sense.
Addresses-Coverity-ID: 1271172 ("Missing break in switch")
Fixes: 87c2d90678 ("power: max77693: Add charger driver for Maxim 77693")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1394724 ("Missing break in switch")
Addresses-Coverity-ID: 114958 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This fixes the value that accounts for the Vce of a transistor in the
LEGO MINDSTORMS EV3 power supply driver. The old value (200mV) was the
max value from the data sheet. After testing, the actual value has been
found to be 50mV. By using 50mV we get a more accurate voltage
indication.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This changes the LEGO MINDSTORMS EV3 power supply driver to return an
error if iio_read_channel_processed() fails.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add a matching table for devicetree probing, and optionally set the module
parameter variables from DT properties.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch removes the w1 slave driver that used to register the w1 family
and instanciate a platform device at runtime. The code now lives in the
supply driver instead to avoid that level of indirection.
The old device name "ds2760-battery.0" is preserved, so userspace
applications can access the same virtual device nodes as before.
Note that because the w1 core does not currently have a framework for
suspend/resume, the driver now registers a PM notifier callback.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We end up reading one element beyond the end of the adp5061_vmax[] array
here.
Fixes: fe8e81b7e8 ("adp5061: New driver for ADP5061 I2C battery charger")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds basic support for Analog Devices I2C programmable linear
battery charger.
With this driver, some parameters can be read and configured such as:
* trickle charge current level (PRECHARGE_CURRENT)
* trickle charge voltage threshold (VOLTAGE_MIN)
* weak charge threshold (VOLTAGE_AVG)
* constant current (CONSTANT_CHARGE_CURRENT)
* constant charge voltage limit (CONSTANT_CHARGE_VOLTAGE_MAX)
* battery full (CAPACITY_LEVEL)
* input current limit (INPUT_CURRENT_LIMIT)
* charger status (STATUS)
* battery status (CAPACITY_LEVEL)
* termination current (CHARGE_TERM_CURRENT)
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADP5061.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
If an iio channel defines a basic property, there are duplicate entries
in /sys/class/power/*/uevent.
So add a check to avoid duplicates. Since all channels may be duplicates,
we have to modify the related error check.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We did have sporadic problems in the pinctrl framework during boot
where a pin group name unexpectedly became NULL leading to a NULL
dereference in strcmp.
Detailled analysis of the failing cases did reveal that there were
two devm allocated objects close to each other. The second one was
the affected group_desc in pinmux and the first one was the
psy_desc->properties buffer of the gab driver.
Review of the gab code showed that the address calculation for
one memcpy() is wrong. It does
properties + sizeof(type) * index
but C is defined to do the index multiplication already for
pointer + integer additions. Hence the factor was applied twice
and the memcpy() does write outside of the properties buffer.
Sometimes it happened to be the pinctrl and triggered the strcmp(NULL).
Anyways, it is overkill to use a memcpy() here instead of a simple
assignment, which is easier to read and has less risk for wrong
address calculations. So we change code to a simple assignment.
If we initialize the index to the first free location, we can even
remove the local variable 'properties'.
This bug seems to exist right from the beginning in 3.7-rc1 in
commit e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We should look at val which contains the value read from the register,
not ret which is always 0 on a successful read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: eac53b3664 ("power: supply: axp288_charger: Drop platform_data dependency")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
getnstimeofday64() is deprecated in favor of the ktime_get() family.
The direct replacement would be ktime_get_real_ts64(), but we only need
the seconds value, and it seems better to use boottime than real time
to avoid unexpected behavior with a concurrent settimeofday().
ktime_get_seconds() might also work, but it seems better to use
boottime than monotonic time since I assume that the charging
process continues during suspend.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Even after the previous fix I have experienced more spurious
poweroffs on the gemini SoC. After this fix it finally seems
to go away.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.
notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.
So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b6 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.
This patch fixes the issues by ensuring that the notifier is installed
only once.
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 46c99ac662 ("power/reset: vexpress: Register with kernel restart handler")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver gets various bits of information about what is connected to
USB PD ports from the EC and converts that into power_supply properties.
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Trivial fix to spelling mistake in dev_warn message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
zx_reboot_probe() increments refcnt of zx296702-pcu device node by
of_find_compatible_node() and leaves it undecremented on both
successful and error paths.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver was originally submitted for the TI BQ20Z75 battery IC
(commit a7640bfa10 ("power_supply: Add driver for TI BQ20Z75 gas gauge
IC")) and later renamed to express generic SBS support. While it's
mostly true that this driver implemented a standard SBS command set, it
takes liberties with the REG_MANUFACTURER_DATA register. This register
is specified in the SBS spec, but it doesn't make any mention of what
its actual contents are.
We've sort of noticed this optionality previously, with commit
17c6d3979e ("sbs-battery: make writes to ManufacturerAccess
optional"), where we found that some batteries NAK writes to this
register.
What this really means is that so far, we've just been lucky that most
batteries have either been compatible with the TI chip, or else at least
haven't reported highly-unexpected values.
For instance, one battery I have here seems to report either 0x0000 or
0x0100 to the MANUFACTURER_ACCESS_STATUS command -- while this seems to
match either Wake Up (bits[11:8] = 0000b) or Normal Discharge
(bits[11:8] = 0001b) status for the TI part [1], they don't seem to
actually correspond to real states (for instance, I never see 0101b =
Charge, even when charging).
On other batteries, I'm getting apparently random data in return, which
means that occasionally, we interpret this as "battery not present" or
"battery is not healthy".
All in all, it seems to be a really bad idea to make assumptions about
REG_MANUFACTURER_DATA, unless we already know what battery we're using.
Therefore, this patch reimplements the "present" and "health" checks to
the following on most SBS batteries:
1. HEALTH: report "unknown" -- I couldn't find a standard SBS command
that gives us much useful here
2. PRESENT: just send a REG_STATUS command; if it succeeds, then the
battery is present
Also, we stop sending MANUFACTURER_ACCESS_SLEEP to non-TI parts. I have
no proof that this is useful and supported.
If someone explicitly provided a 'ti,bq20z75' compatible property, then
we continue to use the existing TI command behaviors, and we effectively
revert commit 17c6d3979e ("sbs-battery: make writes to
ManufacturerAccess optional") to again make these commands required.
[1] http://www.ti.com/lit/er/sluu265a/sluu265a.pdf
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* bq27xxx: Add BQ27426 support
* ab8500: Drop AB8540/9540 support
* Introduced new usb_type property
* Properly document the power-supply ABI
* misc. cleanups and fixes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE72YNB0Y/i3JqeVQT2O7X88g7+poFAlscFLIACgkQ2O7X88g7
+pplkA/+OU3V/sFfbHka6RdoIVeEJCqtQnd1d3VimbKmSpCZQ9W5SnJoc/Dzy3+q
Di0mrFb9nB77H4ShMVVc/rAy4flv7copnI2SJDZ1psx4pX4LS7AwToAlQY1Cr/VR
QBStyZ4aJrvHtdPYggZADAwiU3/vBtI14n28/8TdGlsHFszVbcr2IhiUBYiVgb++
jvQCQyKbxgMfou08wV2Sg/moKXGFh+1HtobRZDyr4Su3A1Nyr6Epyg8gBADi2ZgS
nWaGfYfpI9gaA7g00y/OvqTZroJD+WKAToecl5frgtZ+zHZAQsVGJth9f+LrYXlz
7bERZf94L8MwRNz1Zl8nJ+zHfOmMjEFerHCI81+6wO+klcAgv5AQTcP11a+oZWiQ
5Isq6yt6meg2B4XfBX2EcnXtztnvgb0+lb0KaRUhiQ/5BzupsyIBw8vlJmilGP61
DmL63WrXSb2XChnAkfLbLiKXethY4/y7WjHxPv7esJqy1X6tpFURHwoopv/HWX6N
ctsqOp1D3pl+pBQvOZ4g5oWMTwmlu1uUsKXaZpOYx7+a8CIfJxPVXB+S/D3C5YsU
U1KodhtmhXp8FmbyH1OufARXk9G9rievgOLAPTfsjet06rwpLdy6iLeztvjZIo+T
H5pvkD+1o4P6TiAgsPTnOK9YXGL/Pr4rb2voiu7sKLRAfBr65ww=
=UB16
-----END PGP SIGNATURE-----
Merge tag 'for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- bq27xxx: Add BQ27426 support
- ab8500: Drop AB8540/9540 support
- Introduced new usb_type property
- Properly document the power-supply ABI
- misc. cleanups and fixes
* tag 'for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
MAINTAINERS: add entry for LEGO MINDSTORMS EV3
power: supply: ab8500_charger: fix spelling mistake: "faile" -> "failed"
power: supply: axp288_fuel_gauge: Remove polling from the driver
power: supply: axp288_fuelguage: Do not bind when the fg function is not used
power: supply: axp288_charger: Do not bind when the charge function is not used
power: supply: axp288_charger: Support 3500 and 4000 mA input current limit
power: supply: s3c-adc-battery: fix driver data initialization
power: supply: charger-manager: Verify polling interval only when polling requested
power: supply: sysfs: Use enum to specify property
power: supply: ab8500: Drop AB8540/9540 support
power: supply: ab8500_fg: fix spelling mistake: "Disharge" -> "Discharge"
power: supply: simplify getting .drvdata
power: supply: bq27xxx: Add support for BQ27426
gpio-poweroff: Use gpiod_set_value_cansleep
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
To allow users of the power supply framework to be hw description
agnostic, this commit adds the ability to pass a fwnode pointer,
via the power_supply_config structure, to the initialisation code
of the core, instead of explicitly specifying of_ndoe. If that
fwnode pointer is provided then it will automatically resolve down
to of_node on platforms which support it, otherwise it will be NULL.
In the future, when ACPI support is added, this can be modified to
accommodate ACPI without the need to change calling code which
already provides the fwnode handle in this manner.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary data for handling io voltage domains on PX30.
As interesting tidbit, the PX30 contains two separate iodomain areas.
One in the regular General Register Files (GRF) and one in PMUGRF in the
pmu power domain.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
trivial fix to spelling mistake in dev_error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This is a signed tag/merge point to handle the cross-tree merge of the
USB and power supply subsystems for the patch series:
Subject: [PATCH v8 0/6] typec: tcpm: Add sink side support for PPS
It is based on the usb.git tree, in the usb-next branch, for merging in
4.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuGASg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylqPACcDdrowGIQp0vVa7VrOJNMy9pL5K0An1cjnaUt
0sXkKK8YWC3EQSSYtr3Q
=McRU
-----END PGP SIGNATURE-----
Merge tag 'tags/tcpm-pps-4.18' into psy-next
Tag/Merge point for adding typeC power supply support
This is a signed tag/merge point to handle the cross-tree merge of the
USB and power supply subsystems for the patch series:
Subject: [PATCH v8 0/6] typec: tcpm: Add sink side support for PPS
It is based on the usb.git tree, in the usb-next branch, for merging in
4.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Userspace class/power_supply consumers such as upower, already know some
supplies need to be polled to get up2date info. Doing this in the kernel
and then waking up userspace just causes unnecessary wakeups and i2c
transfers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some devices with an AXP288 PMIC do not have a battery at all, or use
external charger and fuelgauge ICs instead of the AXP288 builtin
functionality.
On such devices we should not bind to the fuelgauge function to avoid
exporting a non working power_supply class device.
This also avoids the following errors repeating over and over again in
dmesg:
axp288_fuel_gauge axp288_fuel_gauge: capacity measurement not valid
axp288_fuel_gauge axp288_fuel_gauge: Error 0xe2 contents not valid
power_supply axp288_fuel_gauge: driver failed to report 'charge_now'
property: -6
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some devices with an AXP288 PMIC do not have a battery at all, or use
external charger and fuelgauge ICs instead of the AXP288 builtin
functionality.
On such devices we should not bind to the charge function to avoid
exporting a non working power_supply class device.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The AXP288 supports an input-current-limit of up to 4000 mA, this
commit adds support for the 3500 and 4000 mA settings which were
missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
For power_supply_get_drvdata() routine to work correctly the driver data
has to be provided when registering power supply, otherwise driver gives up
immediately with these errors:
power_supply main-battery: no battery infos ?!
power_supply main-battery: driver failed to report `status' property: -22
Signed-off-by: Sergiy Kibrik <sakib@darkstar.site>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Driver bails out with -EINVAL when no polling specififaion is requested.
Fix that by verifing polling interval only if polling_mode is different
from CM_POLL_DISABLE.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Power supply property is in fact enum, so reflect it in code.
Also use switch statement in show property function as is done
for storing property.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Trivial fix to spelling mistake in dev_dbg message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This device is software similar to the BQ27426 except it has
different data memory offsets. Add support here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The power-off call is done in a context that must be able to sleep, so
use gpiod_set_value_cansleep instead of the atomic gpiod_set_value call.
This fixes a kernel warning at shutdown when the gpio is controlled
through an IO expander for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This commit adds the 'usb_type' property to represent USB supplies
which can report a number of different types based on a connection
event.
Examples of this already exist in drivers whereby the existing 'type'
property is updated, based on an event, to represent what was
connected (e.g. USB, USB_DCP, USB_ACA, ...). Current implementations
however don't show all supported connectable types, so this knowledge
has to be exlicitly known for each driver that supports this.
The 'usb_type' property is intended to fill this void and show users
all possible USB types supported by a driver. The property, when read,
shows all available types for the driver, and the one currently chosen
is highlighted/bracketed. It is expected that the 'type' property
would then just show the top-level type 'USB', and this would be
static.
Currently the 'usb_type' enum contains all of the USB variant types
that exist for the 'type' enum at this time, and in addition has
SDP and PPS types. The mirroring is intentional so as to not impact
existing usage of the 'type' property.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there's no error checking of this parameter in the
registration function and it's blindly added to psy class and
subsequently used as is. For example if this is NULL the call
to psy_register_thermal() will try to dereference the pointer
thus causing a kernel dump.
This commit updates the registration code to add some basic
checks on the desc pointer validity, name, and presence of
properties.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
* Microsemi Ocelot reset support
* Spreadtrum SC27xx reset support
* generic gpio charger: lot's of cleanups
* axp20x fuel gauge: add AXP813 support
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=VY8H
-----END PGP SIGNATURE-----
Merge tag 'for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Microsemi Ocelot reset support
- Spreadtrum SC27xx reset support
- generic gpio charger: lot's of cleanups
- axp20x fuel gauge: add AXP813 support
- misc fixes, including one devicetree change for the Nokia N900, that
has been Acked-by Tony Lindgren
* tag 'for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (27 commits)
power: reset: at91-reset: Switch from the pr_*() to the dev_*() logging functions
power: reset: at91-poweroff: Remove redundant dev_err call in at91_poweroff_probe()
power: reset: at91-poweroff: Switch from the pr_*() to the dev_*() logging functions
power: reset: make function sc27xx_poweroff_shutdown static
power: supply: da9150-fg: remove VLA usage
ARM: dts: omap3-n900: Add link between battery and charger
power: supply: bq2415x: add DT referencing support
power: supply: bq27xxx: support missing supplier device
max17042: propagate of_node to power supply device
power: supply: axp288_fuel_gauge: Fix full status reporting
power: supply: axp288_fuel_gauge: Do not register FG on ECS EF20EA
power: reset: gpio-poweroff: Support for timeout from device property
dt-bindings: power: reset: gpio-poweroff: Add 'timeout-ms' property
power: reset: Add Spreadtrum SC27xx PMIC power off support
power: supply: axp20x_battery: add support for AXP813
dt-bindings: power: supply: axp20x: add AXP813 battery DT binding
power: supply: axp20x_battery: use data struct for variant specific code
power: supply: gpio-charger: Remove pdata from gpio_charger
power: supply: gpio-charger: Use GPIOF_ACTIVE_LOW for legacy setup
power: supply: gpio-charger: Remove redundant dev_err call in probe function
...
Use dev_info() instead of pr_info().
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There is an error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundancy.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use dev_info() instead of pr_info().
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The function sc27xx_poweroff_shutdown is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/power/reset/sc27xx-poweroff.c:28:6: warning: symbol
'sc27xx_poweroff_shutdown' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In preparation to enabling -Wvla, remove VLA usage and replace it
with fixed-length arrays.
DA9150_QIF_LONG_SIZE (4 bytes) is the biggest size of an attribute which can
be accessed [1].
Fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
[1] https://marc.info/?l=kernel-hardening&m=152059600524753&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
power_supply_am_i_supplied() can return negative error
codes. In this case we should assume, that no charger
is connected and the battery should be marked as
DISCHARGING instead of NOT_CHARGING.
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
max17042_get_status uses the core power_supply_am_i_supplied. That
function relies on DT properties to figure out the power supply
topology, and will error out without DT.
Fixes max17042 battery status being reported as "unknown".
Signed-off-by: Pierre Bourdon <delroth@google.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Commit 2b5a4b4bf2 ("power: supply: axp288_fuel_gauge: Rework
get_status()"), switched from 0A current detection to using the capacity
register for full detection.
It turns out this fixes full reporting on some devices which keep trickle
charging long after the capacity register reach 100%, but breaks it on
some other devices where the charger stops charging before the capacity
register reaches 100%. This commit fixes this by also checking for
0A current when the reported capacity is above 90%.
Fixes: 2b5a4b4bf2 ("psy: axp288_fuel_gauge: Rework get_status()")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The ECS EF20EA laptop ships an AXP288 but it is actually using a
different, separate FG chip for AC and battery monitoring. On this
laptop we need to keep using the regular ACPI driver and disable the
AXP288 FG to avoid reporting two batteries to userspace.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add support for reading a timeout value from device property.
Fall back to previous default of 3s if nothing is specified.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On Spreadtrum platform, we need power off system through external SC27xx
series PMICs including the SC2720, SC2721, SC2723, SC2730 and SC2731 chips.
Thus this patch adds SC27xx series PMICs power-off support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The X-Powers AXP813 PMIC has got some slight differences from
AXP20X/AXP22X PMICs:
- the maximum voltage supplied by the PMIC is 4.35 instead of 4.36/4.24
for AXP20X/AXP22X,
- the constant charge current formula is different,
It also has a bit to tell whether the battery percentage returned by the
PMIC is valid.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We used to use IDs to select a function or a feature depending on the
variant. It's easier to maintain the code by adding data structure
storing the few differences between variants so that we don't add a pile
of if conditions.
Let's use this data structure and update the code to use it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[updated POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN write property to use
the introduced set_max_voltage() callback]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Platform data are now used only during probe time, so remove
them from gpio_charger structure and consolidate probing
function accordingly.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[Replace of_property_read_string with dev_property_read_string]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Setting GPIOF_ACTIVE_LOW flag based on platform data gpio_active_low
makes return value of gpiod_get_value_cansleep directly usable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There is an error message within devm_kzalloc already.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We are currently probing smartreflex with omap_device while we are
already probing smartreflex related interconnect target module with
ti-sysc driver and dts data.
Before we can flip things on for ti-sysc, we need to prepare the
smartreflex driver a bit:
1. The smartreflex clock is really for the whole interconnect target
module. So it may be configured at the parent device level with
ti-sysc
2. With ti-sysc, we have the child device manage interconnect target
module directly if pm_runtime_irq_safe() is set and there is only
one child. In that case nobody else is going to call pm_runtime_get
and put, so we need to add these calls to idle smartreflex properly
after probe if not fully configured
3. With ti-sysc, the parent driver may rebind. So we want to use
platform_driver_register() and don't want probe to be __init
Note that this patch depends on the related changes to ti-sysc driver
and omap_device probing to prevent both ti-sysc and omap_device to
try to probe smartreflex.
Cc: linux-pm@vger.kernel.org
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the D-Link DIR-685 we get spurious poweroff from
infrared. Since that block (CIR) doesn't even have a
driver this can be safely ignored, we can revisit this
code once we have a device supporting CIR.
On the D-Link DNS-313 we get spurious poweroff from
the power button. This appears to be an initialization
issue: we need to enable the block (start the state
machine) before we clear any dangling IRQ.
This patch fixes both issues.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Temperature is measured in tenths of degree Celsius.
Fixes: 085bc24d15 ("Add LTC2941/LTC2943 Battery Gauge Driver")
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch adds the to_power_supply macro to upcast
a device to a power_supply struct.
This is needed because the same piece of code using
container_of is used in various other places, so we
abstract away such low-level operations via a macro.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ognjen Galic <smclt30p@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Using explicit struct device variable makes code a bit more readable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify error unwinding using devm_* allocators. This also
makes driver remove function empty, so remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add properties for charge empty and charge full thresholds.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The Microsemi Ocelot SoC has a register allowing to reset the MIPS core.
Unfortunately, the syscon-reboot driver can't be used directly (but almost)
as the reset control may be disabled using another register.
Cc: linux-pm@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* bq27xxx: add bq27521 support
* drop unused imx-snvs-poweroff driver
* improve axp288 driver
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=XIx5
-----END PGP SIGNATURE-----
Merge tag 'for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- bq27xxx: add bq27521 support
- drop unused imx-snvs-poweroff driver
- improve axp288 driver
- misc fixes
* tag 'for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (32 commits)
power: supply: max17042_battery: Always fall back to default platform-data
power: supply: max17042_battery: Check battery current for status when supplied
MAINTAINERS: Add AXP288 PMIC entry
power: supply: axp288_fuel_gauge: Do not register our psy on (some) HDMI sticks
power: supply: axp288_fuel_gauge: Optimize get_current()
power: supply: axp288_fuel_gauge: Rework get_status()
power: reset: account for const type of of_device_id.data
power: supply: account for const type of of_device_id.data
bq24190: Simplify code in property_is_writeable
power: supply: axp288_fuel_gauge: Get iio-channels once during boot
power: supply: axp288_charger: Properly stop work on probe-error / remove
power: supply: axp288_charger: Simplify extcon cable handling
power: supply: axp288_charger: Use the right property for the input current limit
power: supply: axp288_charger: Pick lower input current limit not higher
power: supply: axp288_charger: Do not cache input current limit value
power: supply: axp288_charger: Remove no longer needed locking
power: supply: axp288_charger: Use regmap_update_bits to set the input limits
power: supply: axp288_charger: Cleanup some double empty lines
power: supply: axp288_charger: Remove charger-enabled state tracking
power: supply: axp288_charger: Add missing newlines to some messages
...
It is possible to have CONFIG_OF enabled on x86 builds, where we have no
firmware provided max17042_platform_data. The CONFIG_OF implementation of
max17042_get_pdata would return NULL in this case, causing the probe to
fail.
Instead always fallback to the default platform-data, as used on x86 sofar,
when there is no firmware provided pdata, independent of CONFIG_OF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Even though the system is supplied, it may still be discharging if the
supply is e.g. only delivering 5V 0.5A. Check the avg battery current if
available for more accurate status reporting.
Cc: James <kernel@madingley.org>
Suggested-by: James <kernel@madingley.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The Intel Compute Stick (Cherry Trail version) and the Meegopad T08 HDMI
stick, both use an axp288 PMIC. They also both have this wired up in such
a way that the detection logic in the PMIC claims that a valid battery is
present, resuling in GNOME and KDE showing a full-battery in their status
bar and power-settings, while these devices do not have a battery.
For lack of a better fix add a DMI blacklist and do not register the
axp288_fuel_gauge psy on devices on the blacklist.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
First check the discharge current, and when that is non 0 use that without
also checking the charge current (which will be 0 then). This makes
get_current() do only 1 i2c read instead of 2 when on battery.
This is esp. important given the pmic i2c bus mutex stuff used on boards
with an axp288 because the SoC's own punit also may access the axp288,
which makes i2c accesses more expensive then normal.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Relying on the (dis)charge current reporting for reporting FULL back to
userspace does not work really well and often leads to the reported status
getting stuck at e.g. 98/99% (the fuelgauge is not perfect) for hours.
What happens is that when the battery is full the axp288 keeps charging it
with a very low current. Until it is really really full and once really
really full, some inaccuracies in the adc lead to it then sometimes
reporting a small discharging rate, even though an external pwr source is
used. So we end up with a status of "charging" for hours after the battery
is actually already full and sometimes this then flip-flops to discharging.
This commit fixes this by first checking if a valid Vbus is present and if
it is present using the fuel-gauge's reported percentage to check for a
full battery.
This commit also changes how get_status() determines if the battery is
charging or discharging when not reporting it as full. We still use the
current direction for this, but instead of reading 4 extra registers for
this (2 16 bit regs), simplify things by using the current-direction bit
in the power-status register, which already gets read anyways.
This also reduces the amount of i2c reads to 1 when on battery and 2
when a valid Vbus is present.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver creates a const structure that it stores in the data
field of an of_device_id array.
Add const to the declaration of the location that receives a value
from the data field to ensure that the compiler will continue to check
that the value is not modified and remove the const-dropping cast on
the access to the data field.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver creates two const structures that it stores in the data
field of an of_device_id array.
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.
Furthermore, adding const to the declaration of the location that
receives a const value from such a field ensures that the compiler
will continue to check that the value is not modified. The
const-discarding cast on the extraction from the data field is thus
no longer needed.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify function that should be trivial.
Signed-off-by: Pavel machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Get iio-channels once during boot, delaying the probe if the axp288_adc
drivers has not loaded yet, instead of getting them on demand each time
we need them.
This fixes the following errors in dmesg:
axp288_fuel_gauge axp288_fuel_gauge: ADC charge current read failed:-19
Which were caused by the ondemand iio-channel read code not finding the
channel when the axp288_adc driver had not loaded yet.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Properly stop any work we may have queued on probe-errors / remove.
Rather then adding a remove driver callback for this, and goto style
error handling to probe, use a devm_action for this.
The devm_action gets registered before we register any of the extcon
notifiers which may queue the work, devm does cleanup in reverse order,
so this ensures that the notifiers are removed before we cancel the work.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify extcon cable handling using the new
devm_extcon_register_notifier_all function to listen to all cables
in one go.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use the right property for the input current limit and make it writable.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The code before this commit would pick 900 mA when asking for an input
current limit of 600mA, rather then 500 mA, not good.
While touching almost all code using the silly xxxMA defines anyways,
also get rid of these simply typing out the numbers and switch the
unit to uA as that is the psy class standard unit for currents.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The hardware may change this underneath us.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Now that we use regmap to do read-modify-write ops everywhere, we can
rely on the regmap lock and no longer need our own lock.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use regmap_update_bits in axp288_charger_set_vbus_inlmt, instead of DIY
code.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
While we are doing cleanups, also remove some double blank lines.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The extcon code is the only one to trigger our worker (outside of the
initial run) and we can rely on it to only call us if things have
changed, so there is no need to track the charger-enabled state.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add missing (terminating) "\n"-s to some dev_dbg messages.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Before this commit we were relying solely on the extcon interface for
cable detection, including to determine if a cable providing vbus is
connected at all. This caused us to turn off charging at boot, because
when we run the initial state processing the axp288-extcon driver is still
running charger-type detection most of the time, so all charger cable
types read as disconnected when we run the initial state processing.
This commit reworks the axp288_charger_extcon_evt_worker flow to use the
VBUS_VALID bit from the PWR_INPUT_STATUS register to determine if we
should turn charging on/off. Note this is the same bit as we use for the
online property.
If VBUS_VALID is set, but the extcon code has not completed the charger
type detection yet, we now simply bail leaving things as configured by
the BIOS (we will get a notifier call when the extcon code is done and
reschedule the axp288_charger_extcon_evt_worker).
The extcon code is the only one to trigger the worker (outside of the
initial run) and we can rely on it to only call us if things have changed,
so while we are completely refactoring axp288_charger_extcon_evt_worker,
also remove the code to check if the state has changed.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There's no user of it in kernel now and it basically functions the same
as the generic syscon-poweroff.c to which we have already switched.
So let's remove it.
Cc: Robin Gong <yibin.gong@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When PSHOLD in a Qualcomm platform is deasserted the PMIC will perform
either a power off or a restart of the system. The action to take is
configured in the PON block, which is controlled by a separate driver.
As the configuration logic was added to the pm8941-pwrkey driver the
comment in do_msm_poweroff() is no longer valid and the name
do_msm_restart() is misleading. Update the naming and drop the comment.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver creates a number of const structures that it stores in the
data field of an of_device_id array.
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.
Furthermore, adding const to the declaration of the location that
receives a const value from such a field ensures that the compiler
will continue to check that the value is not modified. The
const-discarding cast on the extraction from the data field is
thus no longer needed.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds basic support for BQ27521 battery monitor, used in Nokia N9
and N950. In particular, battery voltage is important to be able to
tell when the battery is almost empty. Emptying battery on N950 is
pretty painful, as flasher needs to be used to recover phone in such case.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Now that drivers/i2c/busses/i2c-cht-wc.c uses
"input-current-limit-from-supplier" instead of "extcon-name" the last
user of the bq24190 extcon code is gone, remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The driver sets the fuel gauge to continuous monitoring on startup, for
the models that support this. When the board shuts down, the chip remains
in that mode, causing a few mA drain on the battery every 2 or 10 seconds.
This patch registers a shutdown handler that turns off the monitoring to
prevent this battery drain.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The platform_get_irq_byname() function returns -1 if an error occurs.
zero or positive number on success. platform_get_irq_byname() error
checking for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
If an error occurs when we enable the backup battery charging, we should
go through the error handling path directly.
Before commit db43e6c473 ("ab8500-bm: Add usb power path support") this
was the case, but this commit has added some code between the last test and
the 'out' label.
So, in case of error, this added code is executed and the error may be
silently ignored.
Fix it by adding the missing 'goto out', as done in all other error
handling paths.
Fixes: db43e6c473 ("ab8500-bm: Add usb power path support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
'ret' is know to be 0 at this point, because it has not been updated by the
the previous call to 'abx500_mask_and_set_register_interruptible()'.
Fix it by updating 'ret' before checking if an error occurred.
Fixes: 84edbeeab6 ("ab8500-charger: AB8500 charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Should be discharging_max_duration_ms, not charging_max_duration_ms.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/power/reset/zx-reboot.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The original code does this: "1 << (1 << 11)" which is undefined in C.
Fixes: dbc4deda03 ("power: Adds support for Smart Battery System Manager")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Pull i2c updates from Wolfram Sang:
"This contains two bigger than usual tree-wide changes this time. They
all have proper acks, caused no merge conflicts in linux-next where
they have been for a while. They are namely:
- to-gpiod conversion of the i2c-gpio driver and its users (touching
arch/* and drivers/mfd/*)
- adding a sbs-manager based on I2C core updates to SMBus alerts
(touching drivers/power/*)
Other notable changes:
- i2c_boardinfo can now carry a dev_name to be used when the device
is created. This is because some devices in ACPI world need fixed
names to find the regulators.
- the designware driver got a long discussed overhaul of its PM
handling. img-scb and davinci got PM support, too.
- at24 driver has way better OF support. And it has a new maintainer.
Thanks Bartosz for stepping up!
The rest is regular driver updates and fixes"
* 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (55 commits)
ARM: sa1100: simpad: Correct I2C GPIO offsets
i2c: aspeed: Deassert reset in probe
eeprom: at24: Add OF device ID table
MAINTAINERS: new maintainer for AT24 driver
i2c: nuc900: remove platform_data, too
i2c: thunderx: Remove duplicate NULL check
i2c: taos-evm: Remove duplicate NULL check
i2c: Make i2c_unregister_device() NULL-aware
i2c: xgene-slimpro: Support v2
i2c: mpc: remove useless variable initialization
i2c: omap: Trigger bus recovery in lockup case
i2c: gpio: Add support for named gpios in DT
dt-bindings: i2c: i2c-gpio: Add support for named gpios
i2c: gpio: Local vars in probe
i2c: gpio: Augment all boardfiles to use open drain
i2c: gpio: Enforce open drain through gpiolib
gpio: Make it possible for consumers to enforce open drain
i2c: gpio: Convert to use descriptors
power: supply: sbs-message: fix some code style issues
power: supply: sbs-battery: remove unchecked return var
...
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_usb_init_irq(), positive IRQ numbers are also taken as error
cases. Use "if (irq < 0)" instead of "if (!irq)" to validate the return
value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* pm-pci:
PCI / PM: Add dev_dbg() to print device suspend power states
PCI / PM: Do not resume any devices in pci_pm_prepare()
* pm-avs:
PM / AVS: Use %pS printk format for direct addresses
* pm-docs:
PM: docs: Fix formatting typo in devices.rst
Use kernel preferred dev_* family of functions in place of pr_*,
wherever a device object is present.
Done with the help of coccinelle.
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Variable charging_start is being set but is never read, it is therefore
redundant and can be removed. Cleans up sparse warning:
drivers/power/supply/pcf50633-charger.c:61:3: warning: Value stored to
'charging_start' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Pointer pdata is assigned but never used, so remove it. Cleans up the
clang warning:
drivers/power/supply/generic-adc-battery.c:211:2: warning: Value
stored to 'pdata' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 'unsigned int' and curly braces for 'else'.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since the return value is not checked anyhow, we don't need to store it.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Those variables are immediately assigned a value afterwards.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently when a gpio is defined for battery presence it is only used in
the sbs_get_battery_presence_and_health function for 2 properties.
All other properties currently try to read data form the battery before
returning an error if not present. We should know in advance that no
data is going to returned.
As the driver tries multiple times to access a property, this prevents
a lot of smbus accesses, which had a significant effect on device boot-up.
As when the device is registered lots of property accesses are attempted
during boot.
If no gpio is used for presence detection no change in behaviour should
occur.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds smb alert support via the smbus_alert driver to generate
power_supply_changed notifications when either external power is
removed / applied or a battery inserted / removed.
Use the i2c alert callback to notify the attached battery driver that a
change has occurred.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for Smart Battery System Manager.
A SBSM is a device listening at I2C/SMBus address 0x0a and is capable of
communicating up to four I2C smart battery devices. All smart battery
devices are listening at address 0x0b, so the SBSM muliplexes between
them. The driver makes use of the I2C-Mux framework to allow smart
batteries to be bound via device tree, i.e. the sbs-battery driver.
Via sysfs interface the online state and charge type are presented. If
the driver is bound as ltc1760 (an implementation of a Dual Smart Battery
System Manager) the charge type can also be changed from trickle to fast.
Signed-off-by: Karl-Heinz Schneider <karl-heinz@schneider-inet.de>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes some spelling typos found in Kconfig files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the %pS instead of the %pF printk format specifier for printing
symbols from direct addresses. This is needed for the ia64, ppc64 and
parisc64 architectures.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
- Drop the P-state selection algorithm based on a PID controller
from intel_pstate and make it use the same P-state selection
method (based on the CPU load) for all types of systems in the
active mode (Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to
take cross-CPU utilization updates into account and modify the
schedutil governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the
mediatek cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points
(OPP) DT bindings and update its whitelist of supported systems
(Viresh Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen,
Finley Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to
make it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number
of items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on
x86 in a more straightforward way and to use %pOF instead of
full_name (Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor
issues (Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mAiV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested on Pyra prototype with bq27421.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some devices the USB Type-C port power (USB PD 2.0) negotiation is
done by a separate port-controller IC, while the current limit is
controlled through another (charger) IC.
It has been decided to model this by modelling the external Type-C
power brick (adapter/charger) as a power-supply class device which
supplies the charger-IC, with its voltage-now and current-max representing
the negotiated voltage and max current draw.
This commit adds support for this to the bq24190_charger driver by adding
an external_power_changed callback and calling
power_supply_set_input_current_limit_from_supplier from this callback.
This callback will only get called if the bq24190 has a parent-supply.
Note this replaces the functionality to get the current-limit from an
extcon device, which will be removed in a follow-up commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Register the 5V boost converter as a regulator named "usb_otg_vbus".
This commit also adds support for bq24190_platform_data, through which
non device-tree platforms can pass the regulator_init_data (containing
mappings for the consumer amongst other things).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Set pre-charge and charge-term current, obtained from power_supply_battery_info.
Add sysfs attributes precharge_current & charge_term_current.
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Set minimum system voltage limit obtained from device property.
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add get_config(). Rename set_mode_host() to set_config().
Call get_config() and hw_init() after power_supply_register().
No functional changes.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Support data memory update on BQ27425. Parameters from TI datasheets are also
provided for BQ27500, 545, 421, 441, 621; however these are commented out,
as they are not tested.
Add BQ27XXX_O_CFGUP & _O_RAM for use in bq27xxx_chip_data[n].opts
and by data memory update functions.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
For the existing features, these chips act like others already ID'd,
so they had false but functional IDs. We will be adding features
which require correct IDs, so the following IDs are added:
BQ2752X, 531, 542, 546, 742, 425, 441, 621
Chip-specific features are now tracked by BQ27XXX_O_* flags in di->opts.
No functional changes to the driver.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
To support new features which require different data for each chip, we
unify the bq27xxx_regs and bq27xxx_battery_props tables into a single one.
No functional changes to the driver.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
bq24192i was previously only in ID table, so add it to DT table.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Export the input current limit of the charger as a
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT property on the charger
power_supply class device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some devices the USB Type-C port power (USB PD 2.0) negotiation is
done by a separate port-controller IC, while the current limit is
controlled through another (charger) IC.
It has been decided to model this by modelling the external Type-C
power brick (adapter/charger) as a power-supply class device which
supplies the charger-IC, with its voltage-now and current-max representing
the negotiated voltage and max current draw.
This commit adds a power_supply_set_input_current_limit_from_supplier
helper function which charger power-supply drivers can call to get
the max-current from their supplier and have this applied
through their set_property call-back to their input-current-limit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fix drivers/power/supply/max17042_battery.c:1059:6:
warning: 'acpi_id' may be used uninitialized in this function.
No idea why my gcc version did not catch this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Make these const as they are only passed as an argument to the
function device_create_file and device_remove_file and the corresponding
arguments are of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
On some x86/ACPI boards the DSDT defines an ACPI event handler for
the max17047 IRQ, this causes several problems:
1) We need to share the IRQ to avoid an error getting it
2) Even of we are willing to share, we may fail to share because some
DSDTs claim it exclusivly
3) If we are unable to share the IRQ, or the IRQ is only listed as an
ACPI event source and not in the max1704 firmware node, then the
charge threshold IRQ (which is used to give an IRQ every 1 percent
charge change) becomes a problem, the ACPI event handler will not
update this to the next 1 percent threshold, so the IRQ keeps firing
and we get an IRQ storm pegging 1 CPU core.
This happens despite the max17042 driver not setting the charge
threshold because Windows uses it and leaves it set on reboot.
So if we are unable to get the IRQ we need to reprogram the
charge threshold to its disabled setting.
This commit fixes al of the above, while at it it also makes the error
msg when being unable to get the IRQ consistent with other messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some x86 devices enumerate a max17047 fuel-gauge through a MAX17047
ACPI firmware-node, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds the necessary data for handling io voltage domains on the RV1108.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Integrate with the newly added USB charger interface to limit the current
we draw from the USB input based on the input device configuration
identified by the USB stack, allowing us to charge more quickly from high
current inputs without drawing more current than specified from others.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Don't populate various read only arrays on the stack but make them
static const, making the object code smaller and saves 148 bytes
overall:
Before:
text data bss dec hex filename
11940 4496 64 16500 4074 lp8788-charger.o
After:
text data bss dec hex filename
11472 4816 64 16352 3fe0 lp8788-charger.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use 'sizeof(*var)' instead of the equivalent 'sizeof(data structure type)'
because it is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Update a comment which is no more up to date since commit
2ed9e9b653.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
'devm_kzalloc()' can return NULL. Return -ENOMEM in this case in order to
avoid a NULL pointer dereference later on.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Commit 2848e039c5 ("power: supply: Make power_supply_am_i_supplied return
-ENODEV if there are no suppliers") was supposed to make
power_supply_am_i_supplied() return -ENODEV when there are no supplies
which supply the supply passed to it.
But instead it will only return -ENODEV when there are no supplies at
all as data->count++; is incremented on every call of the iterator, rather
then only when __power_supply_is_supplied_by returns true. This commit
fixes this.
Fixes: 2848e039c5 ("power: supply: Make power_supply_am_i_supplied ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add const to bin_attribute structures as they are only passed to the
functions sysfs_{remove/create}_bin_file or
device_{remove/create}_bin_file. The corresponding parameters
passed are of type const, so declare the structures to be const.
Done using Coccinelle:
@m disable optional_qualifier@
identifier s;
position p;
@@
static struct bin_attribute s@p={...};
@okay1@
position p;
identifier m.s;
@@
(
sysfs_create_bin_file(...,&s@p,...)
|
sysfs_remove_bin_file(...,&s@p,...)
)
@bad@
position p!={m.p,okay1.p};
identifier m.s;
@@
s@p
@change depends on !bad disable optional_qualifier@
identifier m.s;
@@
static
+const
struct bin_attribute s={...};
Same script was modified for device_{create/remove}_bin_file functions.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When the BQ27xxx driver was originally written the w1 subsystem only
allowed device drivers for w1 attached devices to live in the w1
subsystem. Kernel driver subsystems expect that the driver for a device
live in the directory of the subsystem for which it implements
functionality, not in the directory of the bus that it is attached. To
work around this, the BQ27xxx driver was implemented as a platform device
driver and the interface driver would instantiate this device from within
the w1 directory, then pass a w1 read callback as platform data.
As we can now have the w1 interface driver in the power/supply directory
(like we do already with the i2c interface driver) we can remove this
middle-layer platform driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The HDQ interface driver should be in this folder just like the I2C
interface driver. Move this driver out of drivers/w1/slave and into
drivers/power/supply.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
LTC2944 is compatible with LTC2943, but uses different
voltage and current computing constants.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
LTC2942 is pin compatible with LTC2941 providing additional
informations about battery voltage and temperature. It can
be runtime detected using bit A7 in the Status register.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In order to support LTC2942 which has temperature registers
at different offsets than LTC2943 use following register naming
scheme (prefixes):
- LTC294X_ common registers
- LTC2942_ chips specific registers
- LTC2943_ specific registers
LTC2944 is compatible with LTC2943 but uses different constants
to compute voltage and current, so replace num_regs misused
for device indentification with real device id to discriminate
between those two.
There are no functional changes.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Dragos Bogdan <dragos.bogdan@analog.com>
Tested-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
At least with the Inspired Energy compatible batteries a delay is required
after setting the capacity mode bit from amp to watts or the reverse.
Setting the bit and then immediately pooling the status register results
in an unknown error being returned in the register. Add the delay results
in and ok status being return. This was also seen when reading the charge
and energy registers where the wrong value was returned for the requested
mode.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Tested-by: Michael Heinemann <committed@heine.so>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Sort the header includes prior to adding to the list.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
checkpatch issued an error in having the FSF address in the comment.
As address may change and Linux already includes a copy.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The MAX17211 monitor a single cell pack. The MAX17215 monitor and
balance a 2S or 3S pack or monitor a multiple-series cell pack.
Both device use 1-Wire interfce.
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2673 400 0 3073 c01 power/supply/pcf50633-charger.o
File size After adding 'const':
text data bss dec hex filename
2737 336 0 3073 bed power/supply/pcf50633-charger.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
of_irq_get() may return any negative error number as well as 0 on failure,
while the driver only checks for -EPROBE_DEFER, blithely continuing with
the call to devm_request_irq() -- that function expects *unsigned int*,
so would probably fail anyway when a large IRQ number resulting from a
conversion of a negative error number is passed to it... This, however,
is incorrect behavior -- error number is not IRQ number.
Check for 'irq <= 0' instead and return -ENXIO from probe if of_irq_get()
returned 0.
Fixes: a09209acd6 ("power: supply: act8945a_charger: Add status change update support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When CONFIG_OMAP_USB2 is set to 'm' and the charger driver is built-in,
we get this link failure:
drivers/power/supply/cpcap-charger.o: In function `cpcap_charger_probe':
cpcap-charger.c:(.text+0x48c): undefined reference to `omap_usb2_set_comparator'
drivers/power/supply/cpcap-charger.o: In function `cpcap_charger_remove':
cpcap-charger.c:(.text+0x774): undefined reference to `omap_usb2_set_comparator'
This adds a dependency to prevent that problem, while still allowing
compile-testing with the OMAP_USB2 driver completely disabled.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal CPCAP PMIC battery charger")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The capacity mode bit is bit 15. Currently it is written as
default initialized enum and never shifted. This leads to
a behaviour where the BATTERY_MODE is not correctly
recognized and set again.
This commit initializes the enum accordingly.
Signed-off-by: Michael Heinemann <committed@heine.so>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* two fixes for twl4030-charger
-----BEGIN PGP SIGNATURE-----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=shuZ
-----END PGP SIGNATURE-----
Merge tag 'for-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Reichel:
"I have two more fixes for the power-supply subsystem:
- two fixes for twl4030-charger"
* tag 'for-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: twl4030-charger: add deferred probing for phy and iio
power: supply: twl4030-charger: move irq allocation to just before irqs are enabled
* New drivers
- Linear ltc3651 charger driver
- Motorola CPCAP battery fuel-gauge driver
* New chip/feature support
- bq27xxx: prepare for chip data setup
- axp20x_battery: support max charge current setup
* New core features
- add Apple Brick ID type
- support "supplied-from" device property for generic ACPI/pdata support
- support strings for sysfs properties representing enums
- introduce battery-info (backend is DT only for now)
- provide reboot-mode header globally
* Misc. fixes
-----BEGIN PGP SIGNATURE-----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=SsiM
-----END PGP SIGNATURE-----
Merge tag 'for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"New drivers:
- Linear ltc3651 charger driver
- Motorola CPCAP battery fuel-gauge driver
New chip/feature support:
- bq27xxx: prepare for chip data setup
- axp20x_battery: support max charge current setup
New core features:
- add Apple Brick ID type
- support "supplied-from" device property for generic ACPI/pdata support
- support strings for sysfs properties representing enums
- introduce battery-info (backend is DT only for now)
- provide reboot-mode header globally
.. and misc fixes"
* tag 'for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (39 commits)
power: supply: sbs-battery: Don't needlessly set CAPACITY_MODE
power: supply: sbs-battery: Prevent CAPACITY_MODE races
power: supply: bq24735: remove incorrect le16_to_cpu calls
power: supply: sbs-battery: remove incorrect le16_to_cpu calls
power: supply: cpcap-charger: Add missing power_supply_config
power: supply: twl4030-charger: move allocation of iio channel to the beginning
power: supply: twl4030-charger: allocate iio by devm_iio_channel_get() and fix error path
power: supply: core: constify psy_tcd_ops.
dt-bindings: power: supply: cpcap-battery: Add power-supplies property
dt-bindings: power: supply: move max8903-charger.txt to proper location
dt-bindings: power: supply: move maxim,max14656.txt to proper location
power: supply: twl4030_charger: Use sysfs_match_string() helper
power: reset: reboot-mode: Make include file global
power: supply: axp20x_battery: add DT support for battery max constant charge current
power: supply: axp20x_battery: add support for DT battery
power: supply: bq27xxx: Add power_supply_battery_info support
power: supply: bq27xxx: Add chip data memory read/write support
power: supply: bq27xxx: Add bulk transfer bus methods
dt-bindings: power: supply: bq27xxx: Add monitored-battery documentation
power: supply: core: Add power_supply_prop_precharge
...
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
This fixes an issue if both this twl4030_charger driver and
phy-twl4030-usb are compiled as modules and loaded in random order.
It has been observed on GTA04 and OpenPandora devices that in worst
case the boot process hangs and in best case the AC detection fails
with a warning.
Therefore we add deferred probing checks for the usb_phy and the
iio channel for AC detection.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
And initialize workers and notifiers as soon as possible.
This avoids a potential race if irqs are enabled and triggered too early
before the worker is properly set up.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This adds the necessary data for handling io voltage domains on the rk3228.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to the smart battery spec (1), the CAPACITY_MODE bit does not
influence the value read from RelativeStateOfCharge(), so don't bother
changing CAPACITY_MODE when doing such a read.
(1) - Smart Battery Data Specification, Rev 1.1, Dec. 11, 1998
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
A subset of smart battery commands return charge or energy depending on
the CAPACITY_MODE bit setting of BatteryMode(). In order to
unambiguously read a charge or energy value, it is necessary to ensure
that CAPACITY_MODE is set as desired, and not changed for the duration
of the attribute read.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Rafael J. Wysocki
Yuanjiang Yu
Claudiu Beznea
Baolin Wang
Heiko Stuebner
Brian Masney
Jonathan Marek
Alexandre Belloni
Colin Ian King
Sebastian Reichel
Oskari Lemmela
Olliver Schinagl
Rob Herring
Lubomir Rintel
Randy Dunlap
Linus Torvalds
Johan Hovold
Gustavo A. R. Silva
Uwe Kleine-König
Vinod Koul
Liu Xiang
Andreas Kemnade
kbuild test robot
Tomasz Figa
Fabien Parent
Kuninori Morimoto
Dan Carpenter
David Lechner
Angus Ainslie (Purism)
Krzysztof Kozlowski
Ding Xiang
Arnd Bergmann
Sebastian Reichel
Sebastian Reichel
Daniel Mack
Stefan Popa
H. Nikolaus Schaller
Hans de Goede
Linus Walleij
Sudeep Holla
Benjamin Tissoires
Sameer Nanda
Alexey Khoroshilov
Enric Balletbo i Serra
Brian Norris
Kees Cook
Adam Thomson
David Wu
Sergiy Kibrik
Ladislav Michl
Wolfram Sang
Andrew F. Davis
Mike Looijmans
Pierre Bourdon
Carlo Caione
Moritz Fischer
Quentin Schulz
Tony Lindgren
Ognjen Galic
Alexandre Belloni
Julia Lawall
Pavel Machek
Dong Aisheng
Bjorn Andersson
Arvind Yadav
Christophe JAILLET
Ryosuke Saito
Jesse Chan
Pan Bian
Aishwarya Pant
Markus Elfring
Paul Burton
Greg Kroah-Hartman
Wolfram Sang
Phil Reid
Karl-Heinz Schneider
Chanwoo Choi
Masanari Iida
Helge Deller
Liam Breck
Bhumika Goyal
Dragos Bogdan
Alex A. Mihaylov
Sergei Shtylyov
Michael Heinemann
Shawn Nematbakhsh