In Commit 1f45f78f8e ("sctp: allow GSO frags to access the chunk too"),
it held the chunk in sctp_ulpevent_make_rcvmsg to access it safely later
in recvmsg. However, it also added sctp_chunk_put in fail_mark err path,
which is only triggered before holding the chunk.
syzbot reported a use-after-free crash happened on this err path, where
it shouldn't call sctp_chunk_put.
This patch simply removes this call.
Fixes: 1f45f78f8e ("sctp: allow GSO frags to access the chunk too")
Reported-by: syzbot+141d898c5f24489db4aa@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs, 'mlx4_en_destroy_netdev()' is called.
It then calls 'mlx4_en_free_resources()' which does the needed resources
cleanup.
So, doing some explicit kfree in the error handling path would lead to
some double kfree.
Simplify code to avoid such a case.
Fixes: 67f8b1dcb9 ("net/mlx4_en: Refactor the XDP forwarding rings scheme")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This version has some suggestions by Eric Dumazet:
- Use a local variable for the mark in IPv6 instead of ctl_sk to avoid SMP
races.
- Use the more elegant "IP4_REPLY_MARK(net, skb->mark) ?: sk->sk_mark"
statement.
- Factorize code as sk_fullsock() check is not necessary.
Aidan McGurn from Openwave Mobility systems reported the following bug:
"Marked routing is broken on customer deployment. Its effects are large
increase in Uplink retransmissions caused by the client never receiving
the final ACK to their FINACK - this ACK misses the mark and routes out
of the incorrect route."
Currently marks are added to sk_buffs for replies when the "fwmark_reflect"
sysctl is enabled. But not for TW sockets that had sk->sk_mark set via
setsockopt(SO_MARK..).
Fix this in IPv4/v6 by adding tw->tw_mark for TIME_WAIT sockets. Copy the the
original sk->sk_mark in __inet_twsk_hashdance() to the new tw->tw_mark location.
Then progate this so that the skb gets sent with the correct mark. Do the same
for resets. Give the "fwmark_reflect" sysctl precedence over sk->sk_mark so that
netfilter rules are still honored.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INET_CSK_DEBUG is always set and only is used for 2 pr_debug calls.
EXPORT_SYMBOL(inet_csk_timer_bug_msg) is only used by these 2
pr_debug calls and is also unnecessary as the exported string can
be used directly by these calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hyper-v transparent bonding should have used master_dev_link.
The netvsc device should look like a master bond device not
like the upper side of a tunnel.
This makes the semantics the same so that userspace applications
looking at network devices see the correct master relationshipship.
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* WMM element validation
* SAE timeout
* add-BA timeout
* docbook parsing
* a few memory leaks in error paths
-----BEGIN PGP SIGNATURE-----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=mJ4m
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We only have a few fixes this time:
* WMM element validation
* SAE timeout
* add-BA timeout
* docbook parsing
* a few memory leaks in error paths
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The liquidio_watchdog kernel thread is watching over only 12 cores of the
Octeon CN23XX; it's neglecting the other 4 cores that are present in the
CN2360. Fix it by defining LIO_MAX_CORES as 16.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-05-09
This series contains updates to fm10k only.
Jake provides all the changes in the series, starting with adding
support for accelerated MACVLAN devices. Reduced code duplication by
implementing a macro to be used when setting up the type specific
macros. Avoided potential bugs with stats by using a macro to calculate
the array size when passing to ensure that the size is correct.
v2: changed macro reference '#' with __stringify() as suggested by
Joe Perches to patch 2 of the series. Also made sure the updated
series of patches is actually pushed to my kernel.org tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- correct a typo in the value of 'matchPattern' of test 282d, potentially
causing false negative
- allow errors when 'teardown' executes '$TC action flush action bpf' in
test 282d, to fix false positive when it is run with act_bpf unloaded
- correct the value of 'matchPattern' in test e939, causing false positive
in case the BPF JIT is enabled
Fixes: 440ea4ae18 ("tc-testing: add selftests for 'bpf' action")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Misc bug fixes for HNS3 Ethernet Driver
Fixes to some of the bugs found during system test, internal review
and clean-up
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the loopback related function in order
to support the serdes loopback.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The head or tail in hardware is not longer valid when resetting,
current hns3_clear_all_ring use them to clean the ring, which
will cause problem during resetting.
This patch fixes it by using next_to_use and next_to_clean in
the ring struct.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The add/del_tunnel_udp is not implemented in hclge_main moulde,
the NETIF_F_RX_UDP_TUNNEL_PORT feature bit is added automatically
by stack when ndo_udp_tunnel_add is not null in dev->netdev_ops.
This patch removes the add/del_tunnel_udp related function, for
we do not support this feature now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_init_mac_addr is called during reset process, it will
get the mac address from NCL_CONFIG and set it to hardware. If
user has changed the mac address, then the mac address set by
user is lost during resetting.
This patch fixes it by not getting the mac address from NCL_CONFIG
when resetting.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix simple misspelling kashkey_offset should be hashkey_offset.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A well timed kernel preemption in the time_after() loop
in wait_for_idle() can result in a spurious timeout
error to be returned.
Fix it by using readl_poll_timeout() which takes care of
this issue.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: cleanup Global Control 2 register
The mv88e6xxx driver still writes arbitrary values in the Global 1
Control 2 register at setup, which layout differs a lot between chips.
This results in an inconsistent configuration, for example with the
Remote Management Unit (RMU).
The first patch adds an operation for the Cascade Port bits, the second
patch sets the device number in the device mapping function and the
third patch adds an operation to correctly disable the RMU.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The RMU mode bits moved a lot within the Global Control 2 register of
the Marvell switch families. Add an .rmu_disable op to support at least
3 known alternatives.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switches supported by mv88e6xxx have to set their device
number in the Global Control 2 register. Extract this in a read then
write function, called from the device mapping setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the 88E6185 family has bits 15:12 Cascade Port bits in the Global
Control 2 register. Hence inconsistent values are actually written in
this register for other families.
Add a .set_cascade_port operation to isolate the 88E6185 case, and call
it from the device mapping setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx4 modify cq limits the coalescing time parameter and
coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.
Change type of sample-interval and adaptive_rx_coal parameters in mlx4
driver to u32 as the ethtool holds them as u32 and these parameters are
not limited due to mlx4 HW.
Fixes: c27a02cd94 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
mlx4_core misc for 4.18
This patchset contains misc enhancements from the team
to the mlx4 Core driver.
Patch 1 by Eran adds driver version report in FW.
Patch 2 by Yishai implements suspend/resume PCI callbacks.
Patch 3 extends the range of an existing module param from boolean to numerical.
Series generated against net-next commit:
53a7bdfb2a dt-bindings: dsa: Remove unnecessary #address/#size-cells
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the boolean interpretation of msi_x module parameter
to numerical, as follows:
0 - Don't use MSI-X.
1 - Use MSI-X, driver decides the num of MSI-X irqs.
>=2 - Use MSI-X, limit number of MSI-X irqs to msi_x.
In SRIOV, this limits the number of MSI-X irqs per VF.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com>
Reviewed-by: Ajaykumar Hotchandani <ajaykumar.hotchandani@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in struct pci_driver.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If supported, write a driver version string to FW as part of the
INIT_HCA command.
Example of driver version: "Linux,mlx4_core,4.0-0"
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy mbox size to adapter instances of PF0-3 to avoid
mbox log overflow. This fixes the possible protection
fault.
Fixes: baf5086840 ("cxgb4: restructure VF mgmt code")
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
firmware expects HMA memory to be zeroed, use __GFP_ZERO
for HMA memory allocation.
Fixes: 8b4e6b3ca2 ("cxgb4: Add HMA support")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Damir reported a breakage of SO_BINDTODEVICE for UDP sockets.
In absence of VRF devices, after commit fb74c27735 ("net:
ipv4: add second dif to udp socket lookups") the dif mismatch
isn't fatal anymore for UDP socket lookup with non null
sk_bound_dev_if, breaking SO_BINDTODEVICE semantics.
This changeset addresses the issue making the dif match mandatory
again in the above scenario.
Reported-by: Damir Mansurov <dnman@oktetlabs.ru>
Fixes: fb74c27735 ("net: ipv4: add second dif to udp socket lookups")
Fixes: 1801b570dd ("net: ipv6: add second dif to udp socket lookups")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After route cache is flushed via ipv4_sysctl_rtcache_flush(), we forget
to reset fnhe_mtu_locked in rt_bind_exception(). When pmtu is updated
in __ip_rt_update_pmtu(), it will return directly since the pmtu is
still locked. e.g.
+ ip netns exec client ping 10.10.1.1 -c 1 -s 1400 -M do
PING 10.10.1.1 (10.10.1.1) 1400(1428) bytes of data.
>From 10.10.0.254 icmp_seq=1 Frag needed and DF set (mtu = 0)
Signed-off-by: David S. Miller <davem@davemloft.net>
On older windows hosts the net_device instance is returned to
the caller of rndis_filter_device_add() without having the presence
bit set first. This would cause any subsequent calls to network device
operations (e.g. MTU change, channel change) to fail after the device
is detached once, returning -ENODEV.
Instead of returning the device instabce, we take the exit path where
we call netif_device_attach()
Fixes: 7b2ee50c0c ("hv_netvsc: common detach logic")
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 29a5dcae27 ("nfp: flower: offload phys port MTU change") we
take encapsulation headroom into account when calculating the max allowed
MTU. This is unnecessary as the max MTU advertised by firmware should have
already accounted for encap headroom.
Subtracting headroom twice brings the max MTU below what's necessary for
some deployments.
Fixes: 29a5dcae27 ("nfp: flower: offload phys port MTU change")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be47e41d77 ("tipc: fix use-after-free in tipc_nametbl_stop")
we fixed a problem caused by premature release of service range items.
That fix is correct, and solved the problem. However, it doesn't address
the root of the problem, which is that we don't lookup the tipc_service
-> service_range -> publication items in the correct hierarchical
order.
In this commit we try to make this right, and as a side effect obtain
some code simplification.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_warn message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in error string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in res_strings string array
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon says:
====================
qed*: Rdma fixes
This patch series include two fixes for bugs related to rdma.
The first has to do with loading the driver over an iWARP
device.
The second fixes a previous commit that added proper link
indication for iWARP / RoCE.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
A previous commit 4609adc271 ("qede: Fix qedr link update")
added a flow that could allocate rdma event objects from an
interrupt path (link notification). Therefore the kzalloc call
should be done with GFP_ATOMIC.
fixes: 4609adc271 ("qede: Fix qedr link update")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qede driver was loaded on a device configured for iWARP
the l2 mutex wouldn't be allocated, and some l2 related
resources wouldn't be freed.
fixes: c851a9dc43 ("qed: Introduce iWARP personality")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net ns of tun device is assigned on the device creation,
and it never changes, we do not need to use any lock to get it
from alive tun.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davidlohr Bueso says:
====================
net: Update static keys to modern api
The following patches update pretty much all core net static key users
to the modern api. Changes are mostly trivial conversion without affecting
any semantics. The motivation is a resend of patches 1 and 2 from a while[1]
back, and the rest are added patches, specific for -net.
Applies against today's linux-next. Compile tested only.
[1] lkml.kernel.org/r/20180326210929.5244-1-dave@stgolabs.net
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in refcount semantics -- key init is false; replace
static_key_enable with static_branch_enable
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Added a '_key' suffix to udp and udpv6 encap_needed, for better
self documentation.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in refcount semantics -- key init is false; replace
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Added a '_key' suffix to generic_xdp_needed, for better self
documentation.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in refcount semantics -- key init is false; replace
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Added a '_key' suffix to netstamp_needed, for better self
documentation.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in semantics -- key init is false; replace
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Added a '_key' suffix to both ingress_needed and egress_needed,
for better self documentation.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in refcount semantics -- key init is false; replace
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Added a '_key' suffix to memalloc_socks, for better self
documentation.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
No changes in refcount semantics -- key init is false; replace
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long
Christophe JAILLET
Jon Maxwell
Joe Perches
Stephen Hemminger
David S. Miller
Felix Manlunas
Eric Dumazet
Davide Caratti
Yunsheng Lin
Sekhar Nori
Vivien Didelot
Moshe Shemesh
Tariq Toukan
Yishai Hadas
Eran Ben Elisha
Ganesh Goudar
Paolo Abeni
Hangbin Liu
Mohammed Gamal
Pieter Jansen van Vuuren
Jon Maloy
Colin Ian King
Michal Kalderon
Kirill Tkhai
Davidlohr Bueso