Headset was declared previously as a Headphone widget connecting
HSMIC and HSOL/HSOR pins of TWL4030 codec in SDP430 machine driver.
The capture path becomes invalid as the Headphone widget is not a
valid input endpoint.
Instead of that, the Headset is declared as separate Microphone
and Headphone widgets. Current patch modifies audio map:
- Headset Mic: HSMIC with bias
- Headset Stereophone: HSOL, HSOR
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add functions "Headset" and "Mic" to the control "Jack Function" for
activating and de-activating codec input pin LINE1L which is connected to
the mic pin of 4-pole Nokia AV connecter.
Note there is no mic bias voltage management here since bias is coming from
Nokia ASIC and driver for it is not in mainline.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
So far, the prepare callback is called multiple times, BDL entries
are reset and re-programmed at each time.
This patch adds the check to avoid the reset of BDL entries when the
same parameters are used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the hw_ptr_interrupt reaches the boundary, it must check whether
the hw_base was already lapped and corret the delta value appropriately.
Also, rebasing the hw_ptr needs a correction because buffer_size isn't
always aligned to period_size.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Always reset the invalind hw_ptr position returned by the pointer
callback. The behavior should be consitent independently from the
debug option.
Also, add the printk_ratelimit() check to avoid flooding debug
prints.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is an AVDD supply as well, normally one or more of the other
upplies would be tied to it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The active discharge does not bring sufficient benefit to justify the
lengthy times involved so don't do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop inbound packets that are smaller than expected. This has been
observed at the very beginning of the streaming transaction.
And when the hardware is in panic mode (which can only very rarely
happen in case of massive EMI chaos), mute the input channels.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Limit the number of printed warnings to one in case of streaming errors.
printk() happens to be expensive, especially in code called as often as
here.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In snd_free_sgbuf_pags(), vunmap() is called after releasing the SG
pages, and it causes errors on Xen as Xen manages the pages
differently. Although no significant errors have been reported on
the actual hardware, this order should be fixed other way round,
first vunmap() then free pages.
Cc: Jan Beulich <jbeulich@novell.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is an omitted unlock in one snd_mixart_hw_params fail path. Fix it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
s/mutex_lock/mutex_unlock/ on 2 fail paths in snd_pcm_oss_proc_write.
Probably a typo, lock should be unlocked when leaving the function.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At the time of initialization, SNDRV_MIXER_OSS_PRESENT_PVOLUME bit is not
set for MIC (slot 7).
So, the same should not be checked when an application tries to do gain
control for audio recording devices.
Just check slot->present for SNDRV_MIXER_OSS_PRESENT_CVOLUME independently.
Verified with a simple application which opens /dev/dsp for recording and
/dev/mixer for volume control.
Have tested two usb audio mic devices.
Signed-off-by: Viral Mehta <viral.mehta@einfochips.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If ratesp or formatsp values are zero, wrong values are passed to ALSA's
the PCM midlevel code. The bug is showed more later than expected.
Also, clean a bit the code.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The position-buffer on ATI controllers are unreliable as well as
on VIA chips, thus the same workaround for DMA position reading as
VIA is useful for ATI.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI controllers (at least some SB0600 models) appear buggy to handle
64bit DMA. As a workaround, reset GCAP bit0 and let the driver to
use only 32bit DMA on these controllers.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It depends on L3 support from 2.4 kernel (CONFIG_L3) that never got
merged into mainline. Since there's no way to use it on any of
supported machines (iPaq h3100 or h3600), better drop it for now.
It can be reimplemented later using ASoC infrastructure (there's
already a driver for uda1341 codec in mainline, so only CPU and machine
parts need to be written).
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 14fa43f53f ("ASoC: Only
register AC97 bus if it's not done already") added a condition for
calling of soc_ac97_dev_register() but not added for calling of
soc_ac97_dev_unregister(). This patch adds same condition for
soc_ac97_dev_unregister(). Without this fix, kernel crashes when
unloading an asoc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the OOPS during a opl3sa2 card suspend
and resume if the driver is loaded but the card
is not found.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Traditionally, changes to struct file->f_flags have been done under BKL
protection, or with no protection at all. This patch causes all f_flags
changes after file open/creation time to be done under protection of
f_lock. This allows the removal of some BKL usage and fixes a number of
longstanding (if microscopic) races.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The previous commit breaks the (digital-) beep on ALC662.
ALC662 has the connection index 0x05 while ALC662 and ALC272 have the
index 0x04 for the beep widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC662/663 codecs have Beep Amplifier Index 0x04 not 0x05 in 0x0b NID.
Confirmed by testing on real hardware.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CC sound/soc/codecs/twl4030.o
sound/soc/codecs/twl4030.c:1400: warning: braces around scalar initializer
sound/soc/codecs/twl4030.c:1400: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1401: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: warning: initialization from incompatible pointer type
sound/soc/codecs/twl4030.c:1402: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1402: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1402: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1402: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1403: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1403: warning: (near initialization for 'twl4030_dai.ops')
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this patch the drivers do not set the vmixer volume anymore at startup
because it is actually the output volume of the voices and ALSA mandates
that the volume must be 0 by default.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a long standing bug in the drivers for cards with a vmixer because
I overlooked a detail in the c++ generic driver by echoaudio. Those cards
do not have a line-out volume control. It is a virtual control provided by
the generic driver. The bug is harmless because the DSP just ignores the
command to change the volume.
*NB:* It breaks alsa-tools/echomixer. A patch for it will follow.
This patch removes the line-out volume control from vmixer-equipped cards.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the PXA27x series allow 2 gpios to reset the ac97 bus,
allow through platform data configuration the definition of
the correct gpio which will reset the AC97 bus.
This comes from a silicon defect on the PXA27x series, where
the gpio must be manually controlled in warm reset cases.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two issues are fixed here:
- I2S transmits the left frame with the clock low but I don't seem to
get LRCLK out without SFRMDLY being set so invert SFRMP and set a
delay.
- I2S has a clock cycle prior to the first data byte in each channel
so we need to delay the data by one cycle.
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the pxa ssp port usage from network mode to PSP mode.
Removed some comments and checks for configured TDM channels.
A special case is added to support configuration where BCLK = 64fs. We
need to do some black magic in this case which doesn't look nice but
there is unfortunately no other option than that.
Diagnosed-by: Tim Ruetz <tim@caiaq.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move headset jack registration to the codec/machine specific
initialization. Having the jack registration in machine init
causes that the jack device gets initialized but not registered
since the sound card is registered before the jack. Moving jack
registration to device initialization will register the jack
device along with all other devices associated to the card when
the card is registed. As a consequence of jack device registered
properly, the jack is detected as an input device.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the power state of each widget before starting the initialization
work so that all verbs are executed properly.
Also, keep power-up during hwdep reconfiguration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The drivers are basically duplicating the same code over and over.
As snd_soc_cnew is going to be made static some time after the next
merge window, we might as well convert them now.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor the WM8580 device registration to probe via standard I2C device
registration, registering the DAIs once the device has probed via I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the places where the 0x1d widget is used for Conexant 5047, fixing
mismatch introduced after changing the connection.
Signed-off-by: Gregorio Guidi <gregorio.guidi@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8400 is a highly integrated audio CODEC and power management unit
intended for mobile multimedia application. This driver supports the
primary audio CODEC features, including:
- 1W speaker driver
- Fully differential headphone output
- Up to 4 differential microphone inputs
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Buildfix:
CC sound/soc/omap/osk5912.o
sound/soc/omap/osk5912.c: In function 'osk_soc_init':
sound/soc/omap/osk5912.c:189: error: implicit declaration of function 'clk_get_usecount'
make[3]: *** [sound/soc/omap/osk5912.o] Error 1
There's no such (standard) clock interface.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In pxa_ssp_set_dai_fmt(), check whether there is anything to do at all.
If there would be but the SSP port is in use already, bail out.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Clean up Conexant 5047 pareser code:
- Split mixer elements to separate arrays to reduce the duplicated
entires
- Fix mixer element names to the standard ones
- Remove unneeded cxt5047_hp2_unsol_event; the normal unsol_event
handler works fine.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the initial connections of output pins 0x13 and 0x1d for Conexant
5047 codec to point to the mixer amp properly.
Removed unneeded (doubly) verbs from arrays, also removed the unneeded
changing of widget 0x1c, which is now completely unused.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove superfluous verbs from cxt5047_toshiba_init_verbs[].
Also fix comments and minor coding style issues.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create "Capture Source" control dynamically for Conexant codecs.
If only one capture item is available, don't create such a control
since it's just useless.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of binding volumes, create a virtual master volume for Conexant
codecs. This allows separate HP and speaker volume controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Code rework, comments of mail tiwai@suse.de (2009-03-09) incorporated.
Code tested on HP HDX16 (not tested on HDX18 yet).
Signed-off-by: Christoph Plattner <christoph.plattner@gmx.at>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added codec recognition of HP HDX platforms and added support of the
MUTE LED (orange/white). For this feature the CONFIG_SND_HDA_POWER_SAVE
is needed to use event handling for mute control.
Signed-off-by: Christoph Plattner <christoph.plattner@gmx.at>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will break any boards that don't register the AC97 controller
device due to using ASoC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the standard linked list for snd_monitor_file management.
Also, move the list deletion of shutdown_list element into
snd_disconnect_release() (for simplification).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added snd_ctl_add_slave_uncached() function to add a slave element
with volatile controls. The values of normal slave elements are
supposed to be cachable, i.e. they are changed only via the put
callbacks. OTOH, when a slave element is volatile and its values may
be changed by other reason (e.g. hardware status change), the values
will get inconsistent.
The new function allows the slave elements with volatile changes.
When the slave is tied with this call, the native get callback is
issued at each time so that the values are always updated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The timer callbacks are called in the protected status by the lock
of the timer instance, so there is no need for an extra lock in the
PCM substream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up and improve snd_pcm_update_hw_ptr*() functions.
snd_pcm_update_hw_ptr() tries to detect the unexpected hwptr jumps
more strictly to avoid the position mess-up, which often results in
the bad quality I/O with pulseaudio.
The hw-ptr skip error messages are printed when xrun proc is set to
non-zero.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a driver for the SPI connected AK4104 S/PDIF transmitter
device. Its features are fairly simple, but as there is need to set up
certain bits in the IEC958 information, this better goes into a real
driver.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On the HT-Omega Claro (halo) sound cards, the headphone amplifier must
be enabled explicitly by setting a GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removes numbers from the list of features/limitations and makes it
reflect recent changes to the code.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix headphone-detect regression with multiple HP jacks
ALSA: hda - Fix typos in slave controls in patch_sigmatel.c
Wolfram Sang
Takashi Iwai
Lopez Cruz, Misael
Jarkko Nikula
Mark Brown
Giuliano Pochini
Daniel Mack
Jiri Slaby
Viral Mehta
Jaroslav Kysela
Dmitry Artamonow
Atsushi Nemoto
Krzysztof Helt
Paul Mundt
Jonathan Corbet
Joonyoung Shim
Robert Jarzmik
Russell King
Philipp Zabel
Gregorio Guidi
David Brownell
Hugo Villeneuve
Christoph Plattner
Roel Kluin
Risto Suominen
Eric Miao
Clemens Ladisch
Linus Torvalds