Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
On SGI Origin 2k/Onyx2 and SGI Octane systems, there can exist multiple PCI
buses attached to the Xtalk bus. The current code will stop counting PCI buses
after it finds the first one. If one installs the optional PCI cardcage
("shoebox") into these systems, because of the order of the Xtalk widgets, the
current PCI code will find the cardcage first, and fail to detect the BaseIO
PCI devices, which are on a higher Xtalk widget ID.
This patch adds the hooks needed for resolving this issue in the IP27 PCI code
(in a later patch).
Verified on both an SGI Onyx2 and an SGI Octane.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Linux MIPS List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9074/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Return errors immediately so the straightline path is the normal,
no-error path. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, pci_scan_root_bus() created a root PCI bus, enumerated the
devices on it, and called pci_bus_add_devices(), which made the devices
available for drivers to claim them.
Most callers assigned resources to devices after pci_scan_root_bus()
returns, which may be after drivers have claimed the devices. This is
incorrect; the PCI core should not change device resources while a driver
is managing the device.
Remove pci_bus_add_devices() from pci_scan_root_bus() and do it after any
resource assignment in the callers.
Note that ARM's pci_common_init_dev() already called pci_bus_add_devices()
after pci_scan_root_bus(), so we only need to remove the first call:
pci_common_init_dev
pcibios_init_hw
pci_scan_root_bus
pci_bus_add_devices # first call
pci_bus_assign_resources
pci_bus_add_devices # second call
[bhelgaas: changelog, drop "root_bus" var in alpha common_init_pci(),
return failure earlier in mn10300, add "return" in x86 pcibios_scan_root(),
return early if xtensa platform_pcibios_fixup() fails]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
CC: David Howells <dhowells@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Chris Metcalf <cmetcalf@ezchip.com>
CC: Chris Zankel <chris@zankel.net>
CC: Max Filippov <jcmvbkbc@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
This patch converts the pci_load_of_ranges function to use the new common
of_pci_range_parser.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Andrew Murray <Andrew.Murray@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Patchwork: https://patchwork.linux-mips.org/patch/5625/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We currently enable PCI bridges after scanning a bus and assigning
resources. This is often done in arch code.
This patch changes this so we don't enable a bridge until necessary, i.e.,
until we enable a PCI device behind the bridge. We do this in the generic
pci_enable_device() path, so this also removes the arch-specific code to
enable bridges.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The of_node field of the device assigned to a
PCI bus is used during scanning of the PCI bus.
However on MIPS, the of_node field is assigned
only after the bus has been scanned.
Implement the architecture specific version of
'pcibios_get_phb_of_node'. Which ensures that the
PCI driver core will initialize the of_node field
before starting the scan.
Also remove the local assignment of bus->dev.of_node,
it is not needed after the patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The IO and memory resources of a PCI controller
might already have a parent resource set when
they are passed to 'register_pci_controller'.
If the parent resource is set, the request_resource
call will fail due to resource conflict and the
current code will not be able to register the
PCI controller.
Use the parent resource if it is available in the
request_resource call to avoid the isssue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4910/
Signed-off-by: John Crispin <blogic@openwrt.org>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most architectures implement this in exactly the same way. Instead of
having each architecture duplicate this function, provide a single
implementation in the core and make it a weak symbol so that it can be
overridden on architectures where it is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the __init annotations in order to keep pci_fixup_irqs() around
after init (e.g. for hotplug). This requires the same change for the
implementation of pcibios_update_irq() on all architectures. While at
it, all __devinit annotations are removed as well, since they will be
useless now that HOTPLUG is always on.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pci/myron-pcibios_setup:
xtensa/PCI: factor out pcibios_setup()
x86/PCI: adjust section annotations for pcibios_setup()
unicore32/PCI: adjust section annotations for pcibios_setup()
tile/PCI: factor out pcibios_setup()
sparc/PCI: factor out pcibios_setup()
sh/PCI: adjust section annotations for pcibios_setup()
sh/PCI: factor out pcibios_setup()
powerpc/PCI: factor out pcibios_setup()
parisc/PCI: factor out pcibios_setup()
MIPS/PCI: adjust section annotations for pcibios_setup()
MIPS/PCI: factor out pcibios_setup()
microblaze/PCI: factor out pcibios_setup()
ia64/PCI: factor out pcibios_setup()
cris/PCI: factor out pcibios_setup()
alpha/PCI: factor out pcibios_setup()
PCI: pull pcibios_setup() up into core
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Implement pci_load_of_ranges on MIPS. Due to lack of test hardware only 32bit
bus width is supported. This function is based on pci_process_bridge_OF_ranges
from powerpc.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
Here's the wrinkle on Cobalt: we can't generate normal I/O port addresses
on PCI because the GT-64111 doesn't do any address translation, so we have
this:
CPU I/O port addresses [io 0x0000-0xffffff]
PCI bus I/O port addresses [io 0x10000000-0x10ffffff]
Legacy-mode IDE controllers start out with the legacy bus addresses, e.g.,
0x1f0, assigned by pci_setup_device(). These are outside the range of
addresses GT-64111 can generate on PCI, but pcibios_fixup_device_resources()
converted them to CPU addresses anyway by adding io_offset. Therefore, we
had to pre-adjust them in cobalt_legacy_ide_fixup().
With io_offset = 0xf0000000, we had this:
res->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x100001f0 -= io_offset in cobalt_legacy_ide_fixup()
res->start = 0x1f0 += io_offset in pcibios_fixup_device_resources()
The difference after this patch is that the generic pci_bus_to_resource()
only adds the offset if the bus address is inside a host bridge window.
Since 0x1f0 is not a valid bus address and is not inside any windows, it is
unaffected, so we now have this:
region->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x1f0 no offset by pci_bus_to_resource()
That means we can remove both pcibios_fixup_device_resources() and
cobalt_legacy_ide_fixup().
I would *rather* set the host bridge offset to zero (which corresponds
to what the GT-64111 actually does), and have both CPU and PCI addresses
of [io 0x10000000-0x10ffffff]. However, that would require changes to
generic code that assumes legacy I/O addresses, such as pic1_io_resource
([io 0x0020-0x00021]), and we'd have to keep a Cobalt IDE fixup.
Of course, none of this changes the fact that references to I/O port
0x1f0 actually go to port 0x100001f0, not 0x1f0, on the Cobalt PCI bus.
Fortunately the VT82C586 IDE controller only decodes the low 24 address
bits, so it does work.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We never assign anything other than PCI_ASSIGN_ALL_BUSSES to pci_probe,
so just remove the indirection. If configurability is required in the
future, please use the pci_flags/PCI_REASSIGN_ALL_BUS functionality
as is done for powerpc.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves mips to the pci_flags approach so
generic code can use the same test across all architectures.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On MIPS the generic PCI code has always defaulted to L1_CACHE_BYTES
because the architecutre PCI code did not provide a better default.
In particular on systems with S-caches or T-caches this was suboptimal.
Provide a better default by setting pci_dfl_cache_line_size based on
the size of the line size of the lowest level of the cache hierarchy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2982/
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
Based on original patch by Deng-Cheng Zhu.
Reference: https://lkml.org/lkml/2011/8/26/89
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Deng-Cheng Zhu <dczhu@mips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).
There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The GT-64111 PCI host bridge has no address translation mechanism, so
it can't generate legacy port accesses. This quirk fixes legacy device
port resources to contain the bus addresses actually generated by the
GT-64111.
I think this is the approach Ben Herrenschmidt suggested long ago:
http://marc.info/?l=linux-kernel&m=119733290624544&w=2
This allows us to remove the IORESOURCE_PCI_FIXED hack from
pcibios_fixup_device_resources(), which converts bus addresses to CPU
addresses. IORESOURCE_PCI_FIXED denotes resources that can't be moved;
it has nothing to do with converting bus to CPU addresses.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-mips@linux-mips.org
Tested-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/998/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the mips common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented. This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.
Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below changes register_pci_controller() such that controllers
being added after pcibios_init() has run are be scanned immediately.
This is needed for example by the BCM47xx PCI controller, which is located
on the SSB bus, which is now initialized after the PCI subsystem.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The pcibios_max_latency variable is needlessly defined global, and this
patch makes it static.
Build-tested using malta_defconfig.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following symbols
hose_head
hose_tail
are needlessly defined global in arch/mips/pci/pci.c, and
this patch makes them static.
The variable pci_isa_hose is not used, and is removed by
this patch.
Spotted by namespacecheck. Tested by booting a Malta 4Kc
board up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS version of pcibios_enalbe_resources did not have the fixes
from ed6d14f976 yet which under circumstances
similar to x86 might result in failures.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There might be other reasons why a resource might be marked as fixed
such as a PCI UART holding the system console but until we use
IORESOURCE_PCI_FIXED that way also this will work.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d several callers of
pcibios_resource_to_bus are no longer marked __devinit resulting in a
pile of modpost warnings if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x15dde8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_map_rom_copy')
WARNING: vmlinux.o(.text+0x15e140): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0x15f0cc): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f0f0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f114): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f138): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f438): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
WARNING: vmlinux.o(.text+0x15f4f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
Removing __devinit from pcibios_resource_to_bus make the same necessary
for pcibios_fixup_device_resources as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d pcibios_fixup_bus's caller
pci_scan_child_bus is no longer marked __devinit resulting in this modpost
warning if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x158b9c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes this warning:
arch/mips/pci/pci.c:284:18: warning: symbol 'dev' shadows an earlier one
arch/mips/pci/pci.c:272:17: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Bjorn Helgaas
Lorenzo Pieralisi
Linus Torvalds
Joshua Kinard
Yijing Wang
Andrew Murray
Yinghai Lu
Gabor Juhos
Ralf Baechle
Greg Kroah-Hartman
Bill Pemberton
Thierry Reding
Myron Stowe
John Crispin
Myron Stowe
Paul Gortmaker
Lucas De Marchi
Bjorn Helgaas
Dominik Brodowski
Aurelien Jarno
Atsushi Nemoto
Dmitri Vorobiev