Fix this from the logs:
usb 7-1: New USB device found, idVendor=046d, idProduct=08ca
...
usb 7-1: Warning! Unlikely big volume range (=3072), cval->res is probably wrong.
usb 7-1: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Spotted by sparse:
sound/usb/bcd2000/bcd2000.c:73:1: warning: symbol 'devices_used' was not declared. Should it be static?
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Microsoft LifeCam Studio (045e:0772) needs a similar quirk for
suppressing the wrong sample rate inquiry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Roland SC-D70 reports its device class as vendor specific class and
the quirk QUIRK_AUDIO_FIXED_ENDPOINT was used for audio output.
In the quirks table the sampling rate was hard-coded to 44100 Hz
and therefore not worked when the sound module was in 48000 Hz mode.
In this change the quirk is changed to QUIRK_AUDIO_STANDARD_INTERFACE
but as the sound module reports incorrect bSubframeSize in its
descriptors, additional change is made in format.c to detect it and
to override it (which uses the existing code for Edirol SD-90).
Tested both when the sound module was in 44100 Hz mode and 48000 Hz
mode and both audio input and output. MIDI related part of the driver
is not touched.
Signed-off-by: Takamichi Horikawa <takamichiho@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds Microsoft LifeCam Cinema USB ID to the snd_usb_get_sample_rate_quirk list as the Lifecam Cinema does not appear to support getting the sample rate.
Fixes the issue where the LifeCam Cinema would wait for USB timeout and log the message "cannot get freq at ep 0x82" when accessed.
Addresses bug report https://bugzilla.kernel.org/show_bug.cgi?id=95961.
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds an entry for Creative USB X-Fi to the rc_config array in
mixer_quirks.c to allow use of volume knob on the device.
Adds support for newer X-Fi Pro card, known as "Model No. SB1095"
with USB ID "041e:3237"
Signed-off-by: Dmitry M. Fedin <dmitry.fedin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding this quirk allows us to avoid the noisy
"cannot get freq at ep 0x1" message in dmesg output every time
playback starts.
This ought to affect other Benchmark DAC1 variations using the same
"Microchip Technology, Inc." chip as well, but I have only tested
with the "Pre" variant.
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Cc: Joe Turner <joe@oampo.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device complies to the UAC1 standard but hides that fact with
proprietary descriptors. The autodetect quirk for Roland devices
catches the audio interface but misses the MIDI part, so a specific
quirk is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Rafa Lafuente <rafalafuente@gmail.com>
Tested-by: Raphaël Doursenaud <raphael@doursenaud.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usages of clamp() macro in sound/usb/line6/playback.c are just
wrong, the low and high values are swapped.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix problem where playback of Denon DA-300USB DAC sometimes does not
start and leads to error messages like "clock source 41 is not valid,
cannot use".
Solution: Treat this device the same as other Denon/Marantz devices in
sound/usb/quirks.c.
Tested with both PCM and DSD formats.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93261
Signed-off-by: Frank C Guenther <bugzilla.frnkcg@spamgourmet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds a quirk to disable the check that the sample rate has been set correctly, as the Lifecam does not support getting the sample rate.
This means that we don't need to wait for the USB timeout when attempting to get the sample rate. Waiting for the timeout causes problems in some applications, which give up on the device acquisition process before it has had time to complete, resulting in no sound.
[minor tidy up by tiwai]
Signed-off-by: Joe Turner <joe@oampo.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The address cannot be negative so make it unsigned. Also, an unsigned
int is always sufficient for the length, so no need to overdo it with a
size_t. Finally, add in range checks to see if the values passed in
actually fit where they are used.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The firmware version is a single byte so have the variable type agree.
Since the address to this member is passed to the read function, using
an int is not even portable.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put an upper bound on how long we will wait for the device to respond to
a read/write request (i.e., 100 milliseconds) and return an error if
this is reached.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device indicates the result of a read/write operation by making the
status available on a subsequent request from the driver. This is not
ready immediately, though, so the driver is currently slamming the
device with hundreds of pointless requests before getting the expected
response. Add a two millisecond delay before each attempt. This is
approximately the behavior observed with version 4.2.7.1 of the Windows
driver.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The first URBs are submitted during the prepare stage. When .trigger is
called, the ALSA core saves a trigger tstamp that doesn't correspond to
the actual time when the samples are submitted. The trigger_tstamp is
now updated when the first data are submitted to avoid any time offsets.
A usb-specific trigger_tstamp_pending_update flag is used for now,
at some point the flag would need to move to the ALSA core, USB
is not the only interface where silent block transfers are programmed
as part of the prepare stage, with actual data enabled when .trigger
is called.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide a unique name for each driver instead of using "line6usb" for
all of them. This will allow for different configurations based on the
driver type.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is unlikely this function would ever be used in a context without a
pointer to a `struct usb_line6_toneport', so grab the device type from
it rather than having the caller do it.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a predicate for testing if the device supports source selection to
make the conditional logic around this a bit cleaner.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
line6_start_timer passes an unsigned int as argument to be used in mod_timer
which is then used by mod_timer as unsigned long, this just fixes up the
argument type. This change helps make static code checkers happy.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use of this function ended with commits 3e58c868db ("staging: line6:
drop midi_mask_receive") and af89d2897a ("staging: line6: drop
midi_mask_transmit".)
[Removed the corresponding line in midibuf.h, too -- tiwai]
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function has not been used since merging the driver into the kernel
(and a good while before that.)
[Removed the corresponding line in midibuf.h, too -- tiwai]
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of them are rather relevant with the definitions in driver.h,
and there are only a few lines, so just rip it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just reformatting the comments and typos fixed, no functional
changes. Particularly,
- avoid the kerneldoc marker "/**",
- reduce multiple comment lines into single lines,
- corrected wrongly referred function names
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The user-space API definition for usb_stream stuff should be moved
to include/uapi/sound to be exposed publicly.
While we're at it, add the missing ifdef guard for double inclusion,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both playback and capture callbacks are identical, so let's merge
them.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code deals with the stream start / stop solely via
line6_pcm_acquire() and line6_pcm_release(). This was (supposedly)
intended to avoid the races, but it doesn't work as expected. The
concurrent acquire and release calls can be performed without proper
protections, thus this might result in memory corruption.
Furthermore, we can't take a mutex to protect the whole function
because it can be called from the PCM trigger callback that is an
atomic context. Also spinlock isn't appropriate because the function
allocates with kmalloc with GFP_KERNEL. That is, these function just
lead to singular problems.
This is an attempt to reduce the existing races. First off, separate
both the stream buffer management and the stream URB management. The
former is protected via a newly introduced state_mutex while the
latter is protected via each line6_pcm_stream lock.
Secondly, the stream state are now managed in opened and running bit
flags of each line6_pcm_stream. Not only this a bit clearer than
previous combined bit flags, this also gives a better abstraction.
These rewrites allows us to make common hw_params and hw_free
callbacks for both playback and capture directions.
For the monitor and impulse operations, still line6_pcm_acquire() and
line6_pcm_release() are used. They call internally the corresponding
functions for both playback and capture streams with proper lock or
mutex. Unlike the previous versions, these function don't take the
bit masks but the only single type value. Also they are supposed to
be applied only as duplex operations.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clearing prev_fsize in line6_pcm_acquire() is pretty racy.
This can be called at any time while the stream is being played.
Rather better to clear prev_fbuf and prev_fsize at the proper place
like the stream stop for capture, and just after copying the monitor /
impulse data inside the spinlock.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The impulse and monitor handling in submit_audio_out_urb() isn't
protected thus this can be racy with the capture stream handling.
This patch extends the range to protect via each stream's spinlock
(now the whole submit_audio_*_urb() are covered), and take the capture
stream lock additionally for the impulse and monitor handling part.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the check of multi configurations before snd_card_new() as a
short path, and reduce superfluous pointer references.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of allocating the private data individually in each driver's
probe at first, let snd_card_new() allocate the data that is called in
line6_probe(). This simplifies the primary probe functions.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interface argument is used just for retrieving the assigned
device, which can be already found in line6->ifcdev. Drop them from
the callbacks. Also, pass the usb id to private_init so that the
driver can deal with it there. This is a preliminary work for the
further cleanup to move the whole allocation into driver.c.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A minor optimization; while pausing, the driver just copies the zero
that doesn't need any volume changes.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM stream buffer allocation and free are identical for both
playback and capture streams. Provide single helper functions.
These are used only in pcm.c, thus they can be even static.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codes to unlink and sync URBs are identical for both playback and
capture streams. Consolidate to single helper functions.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a new line6_pcm_stream structure and group individual
fields of snd_line6_pcm struct to playback and capture groups.
This patch itself just does rename and nothing else. More
meaningful cleanups based on these fields shuffling will follow.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the problem still really remains, we should fix it instead of
papering over it like this...
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using a decremental loop without particular reasons worsens the
readability a lot. Use incremental loops instead.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The trigger callback is already spinlocked, so we need no more lock
here (even for the linked substreams). Let's drop it.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
line6_pcm_acquire() tries to restore the newly obtained resources at
the error path. But some flags aren't recorded and released properly
when the corresponding buffer is already present. These bits have to
be cleared in the error recovery, too.
Also, "flags_final" can be initialized to zero since we pass only the
subset of "channels" bits.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed a few places using bits OR wrongly for condition checks.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The midi_transmit_lock is used always inside the send_urb_lock, thus
it doesn't play any role. Let's kill it. Also, rename
"send_urb_lock" as a more simple name "lock" since this is the only
lock for midi.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function isn't used any longer after rewriting from sysfs to leds
class in toneport.c.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix memory leak at probe error path by rearranging the call order in
line6_destruct() so that the common destructor is always called.
Also this simplifies the error path to a single goto label.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of non-standard sysfs, reimplement the LED controls on
TonePort as LED class devices.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently disconnect callback is used as a driver's destructor, and
this has to be called not only at the disconnection time but also at
the error paths during probe.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... so that timer_del_sync() in the destructor can be called safely at
any time. Also move the mod_timer() call in toneport_setup(), which
is a bit clearer place.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interface and driver objects are always set when callbacks are
called. Drop such superfluous NULL checks in init and disconnect
calls of each driver.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's utterly unsafe to proceed further the disconnect procedure if the
assigned usbdev is inconsistent with the expected object. Better to
put a WARN_ON() for more cautions and abort immediately.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver version string was removed in an ealier commit for being
useless. These are equally useless.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The correct spelling includes the space. Fix this in strings and
comments that refer to the manufacturer.
Signed-off-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call line6_pcm_disconnect() at disconnect to make sure that all URBs
are cleared. Also reduce the superfluous snd_pcm_stop() calls from
the function (and remove the unused function) since the streams are
guaranteed to be stopped at this point via snd_card_disconnect().
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calling line6_pcm_disconnect() at suspend callback is superfluous and
rather confusing. Let's get rid of it.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Such a debug is needed in the core code, not in each lowlevel driver.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is rather useless for a driver that has been already merged into
the official tree.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a fairly big rewrite regarding the card resource management in
line6 drivers:
- The card creation is moved into line6_probe(). This adds the global
destructor to private_free, so that each driver doesn't have to call
it any longer.
- The USB disconnect callback handles the card release, thus each
driver needs to concentrate on only its own resources. No need to
snd_card_*() call in the destructor.
- Fix the potential stall in disconnection by removing
snd_card_free(). It's replaced with snd_card_free_when_closed()
for asynchronous release.
- The only remaining operation for the card in each driver is the call
of snd_card_register(). All the rest are dealt in the common module
by itself.
- These ended up with removal of audio.[ch] as a result of a reduction
of one layer. Each driver just needs to call line6_probe().
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM trigger callback is guaranteed to be called already in
spinlock / irq-disabled context.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The line6 drivers don't support the full resume although they set
SNDRV_PCM_INFO_RESUME. These flags have to be dropped to inform
properly to the user-space.
Also, drop the CONFIG_PM in trigger callbacks, too, which are rather
superfluous.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous fix for PCM, attach the card-specific resource into
rawmidi->private_data instead of handling in a snd_device object.
This simplifies the code and structure.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of handling the card-specific resource in snd_device, attach
it into pcm->private_data and release it directly in private_free.
This simplifies the code and structure.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of sysfs and the conditional build with Kconfig, implement the
handling of the impulse response controls via control API, and always
enable the build. Two new controls, "Impulse Response Volume" and
"Impulse Response Period" are added as a replacement for the former
sysfs files.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split to each individual driver for POD, PODHD, TonePort and Variax
with a core LINE6 helper module. The new modules follow the standard
ALSA naming rule with snd prefix: snd-usb-pod, snd-usb-podhd,
snd-usb-toneport and snd-usb-variax, together with the corresponding
CONFIG_SND_USB_* Kconfig items.
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Wolfram Sang
Takashi Iwai
Vittorio G (VittGam)
Takamichi Horikawa
Adam Honse
Dmitry M. Fedin
Eric Wong
Daniel Mack
Frank C Guenther
Joe Turner
Chris Rorvick
Pierre-Louis Bossart
Nicholas Mc Guire