The first pass of fixes to cause the driver to continue streaming even when
there is no video arriving over the ITU656 bus were not adequate. Continue
the work from the previous patch.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need the au0828 to continue delivering frames even when the device is not
delivering video, or else applications such as tvtime will block indefinitely.
Unfortunately, the au8522 doesn't have any sort of free-running mode or "blue
screen on no video" like some other decoders.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tweak the comb filter config when in s-video mode to match the Hauppauge
Windows driver values (based on register dumps).
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Straighten out the clamp control configurations for the various video modes,
based off of register diffs done against the Hauppauge Windows driver.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup the routine which disables the audio decoder. In particular, the i2s
output was being shut off but the audio processor itself was not, resulting
in more power being consumed than needed.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the alignment of fields being delivered by the driver, which was
resulting in jerky video when there was horizontal motion (since the bottom
field of the frame was being sent with the top field of the previous frame)
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We had the max packets per URB set to an incredibly low "10" as opposed to
the Windows driver which has it as 128. Set the value to match the
Windows driver, which will reduce interrupts considerably.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The chip's default value for the brightness didn't match what we were sending
back in the queryctrl ioctl(), so if the application actually set the
brightness to the "default", it would actually end up being way too bright.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bad value prevented the autogain to work correctly
and some images were truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Generate a release button event when the button is still pressed when the
stream stops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_xirlink_cit: Add support camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least on the ibm netcam pro frames have a 4 byte footer, take this
into account when calculating sizeimage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following usb bandwidth allocation changes were made to the ibm netcam
pro code:
- Don't restart negotiation at max packet size on stop0, as that gets called
by gspca_main during negotiation. Move this to sd_isoc_init.
- Don't ask for full bandwidth when running at 160x120, that does not need
full bandwidth
- Make minimum acceptable bandwidth depend upon resolution
[mchehab@redhat.com: Fix CodingStyle problems at switch statements]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently alloc_and_submit_int_urb() is setting gspca->int_urb
as soon as the allocation has succeeded, but if the subsequent
submit fails, the urb gets destroyed. And then later will
get destroyed again in gspca_input_destroy_urb() because
gspca->int_urb is set, leading to a double free.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently gspca supported usb-1.1 webcams for which we support the input
button through an interrupt endpoint won't stream (not enough bandwidth
error) when used through an USB-2.0 hub.
After much debugging I've found out that the cause for this is that the
ehci-sched.c schedeling code does not like it when there are already urb's
scheduled when (large) isoc urbs are queued. By moving the submission
of the interrupt urbs to after submitting the isoc urbs the camera
starts working again through usb-2.0 hubs.
Note that this does not fix isoc. streaming through a usb-hub while another
1.1 usb device (like the microphone of the same cam) is also active
at the same time :(
I've spend a long time analyzing the linux kernel ehci scheduler code,
resulting in this (long) mail:
http://www.spinics.net/lists/linux-usb/msg37982.html
The conclusion of the following mail thread is that yes there are several
issues when using usb-1.1 devices through a usb-2.0 hub, but these are not
easily fixable in the current code. Fixing this in ehci-sched.c requires
an almost full rewrite, which is not bound to happen anytime soon.
So with this patch gspca driven usb-1.1 webcams will atleast work when
connected through an usb-2.0 hub when the microphone is not used.
As an added bonus this patch avoids extra destroy/create input urb cycles
when we end up falling back to a lower speed alt setting because of bandwidth
limitations.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DM04/QQBOX USB Timing change.
Improved timing to avoid USB corruptions on some systems.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improved frontend handling.
Frontend now remains open at all times, with signal lock, snr & signal level
polled from Interupt.
Updated driver for DM04/QQBOX USB DVB-S BOXES to version 1.70.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you suspend and resume during video capture, the video colours
are corrupted on resume. This is because the sensor is being unconditionally
powered off during the resume path.
Only power down during resume if the camera is not in use, and correctly
reconfigure the sensor during resume.
Fixes http://dev.laptop.org/ticket/10190
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although cx231xx has a very good IR support, already supported by
mceusb driver, some designs decided to add a separate I2C
microcontroller chip in order to handle IR.
Due to that, add a glue to ir-kbd-i2c is needed, in order to support
those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By comparing the traffic between Pixelview (cx23102-based and Kworld
(saa7134-based), the only difference is at register 0xd5. After some
tests, It seems that it is used to change mode between serial and parallel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the trivial bits to mb86a20s. As the driver won't touch
at the channel/layer parameters, this may not be enough for
receiving all channels, especially ISDB-Tsb, but the driver worked
properly for receiving video channels on my tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses an em2874B + Sharp 921 One Seg frontend.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On our tests with Leadership ISDBT, the s921 frontend were not work. As its
design contained some weird things, it ended to be easier to just re-write
it, getting another frontend as an example (cx24123).
As the old s921 driver weren't used, there's no regression. Some info from
the old frontend were used as a way to double check the behavior that were
noticed on the USB dumps retrieved from Leadership driver.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent patch has introduced a regression, whereby a second open of an
soc-camera video device breaks the running capture. This patch fixes this bug
by guaranteeing, that video buffers get initialised only during the first open
of the device node.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the remaining users of flush_scheduled_work() in
media/video.
* bttv-input.c and cx23885-input.c don't use workqueue at all. No
need to flush.
* Make omap24xxcam.c and saa7134-empress.c flush the used work
directly.
* In fd_defio.c, replace cancel_delayed_work() +
flush_scheduled_work() with cancel_delayed_work_sync(). While at
it, replace the deprecated cancel_rearming_delayed_work() with
cancel_delayed_work_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Video drivers request submodules using a work during probe and calls
flush_scheduled_work() on exit to make sure the work is complete
before being unloaded. This patch makes these drivers flush the work
directly instead of using flush_scheduled_work().
While at it, relocate request_submodules() call in saa7134_initdev()
right right before successful return as in other drivers to avoid
failing after the work is scheduled and returning failure without the
work still active.
This is in preparation for the deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
flush_scheduled_work() is deprecated and scheduled to be removed.
* Flush the used works directly.
* Replace the deprecated cancel_rearming_delayed_work() +
flush_scheduled_work() -> cancel_delayed_work_sync().
* Make sure mantis->uart_work isn't running on exit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (21 commits)
[media] mceusb: set a default rx timeout
[media] mceusb: fix inverted mask inversion logic
[media] mceusb: add another Fintek device ID
[media] lirc_dev: fixes in lirc_dev_fop_read()
[media] lirc_dev: stray unlock in lirc_dev_fop_poll()
[media] rc: fix sysfs entry for mceusb and streamzap
[media] streamzap: merge timeout space with trailing space
[media] mceusb: fix keybouce issue after parser simplification
[media] IR: add tv power scancode to rc6 mce keymap
[media] mceusb: buffer parsing fixups for 1st-gen device
[media] mceusb: fix up reporting of trailing space
[media] nuvoton-cir: improve buffer parsing responsiveness
[media] mceusb: add support for Conexant Hybrid TV RDU253S
[media] s5p-fimc: Fix output DMA handling in S5PV310 IP revisions
[media] s5p-fimc: Use correct fourcc code for 32-bit RGB format
[media] s5p-fimc: Convert m2m driver to unlocked_ioctl
[media] s5p-fimc: Explicitly add required header file
[media] s5p-fimc: Fix vidioc_g_crop/cropcap on camera sensor
[media] s5p-fimc: BKL lock removal - compilation fix
[media] soc-camera: fix static build of the sh_mobile_csi2.c driver
...
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Its possible for the call to read rx timeout from the hardware to fail,
in which case we end up with a bogus rx timeout value. Set a default one
when filling in the rc struct, and we'll just overwrite it later w/the
value from hardware, but if that read fails, we've at least got a sane
rx timeout value to work with (1000ms is the default value I've seen
returned on most if not all mceusb hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As it turns out, somewhere along the way, we managed to invert the
meaning of the tx_mask_inverted flag. Looking back over the old lirc
driver, tx_mask_inverted was set to 0 if the device was in tx_mask_list.
Now we have a tx_mask_inverted flag set to 1 for all the devices that
were in the list, and set tx_mask_inverted to that flag value, which is
actually the opposite of what we used to set, causing set_tx_mask to use
the wrong mask setting option. Since there seem to be more devices with
inverted masks than not (using the original device as the baseline for
inverted vs. normal), lets just call the ones currently marked as
inverted normal instead, and flip the if/else actions that key off of
the inverted flag.
Note: the problem only cropped up if a call to set_tx_mask was made, if
no mask was set, the device would work just fine, which is why this
managed to slip though w/o getting noticed until now.
Tested successfully by myself and Dennis Gilmore.
Reported-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes several changes but they're in one function and sort of
related:
"buf" was leaked on error. The leak if we try to read an invalid
length is the main concern because it could be triggered over and
over.
If the copy_to_user() failed, then the original code returned the
number of bytes remaining. read() is supposed to be the opposite way,
where we return the number of bytes copied. I changed it to just return
-EFAULT on errors.
Also I changed the debug output from "-EFAULT" to just "<fail>" because
it isn't -EFAULT necessarily. And since we go though that path if the
length is invalid now, there was another debug print that I removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We shouldn't unlock here. I think this was a cut and paste error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more
difficult to make use of the devices in userspace as their names can
change.
Signed-off-by: Paul Bender <pebender@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are cases where we get an ending space, and our trailing timeout
space then gets sent right after it, which breaks repeat, at least for
lirc userspace decoding. Merge the two spaces by way of using
ir_raw_event_store_filter, set a timeout value, and we're back to good.
Successfully tested with streamzap and windows mce remotes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Something I failed to notice while testing the mceusb RLE buffer
decoding simplification patches was that we were getting an extra event
from the previously pressed key.
As was pointed out to me on irc by Maxim, this is actually due to using
ir_raw_event_store_with_filter without having set up a timeout value.
The hardware has a timeout value we're now reading and storing, which
properly enables the transition to idle in the raw event storage
process, and makes IR decode behave correctly w/o keybounce.
Also remove no-longer-used ir_raw_event struct from mceusb_dev struct
and add as-yet-unused enable flags for carrier reports and learning
mode, which I'll hopefully start wiring up sooner than later. While
looking into that, found evidence that 0x9f 0x15 responses are only
non-zero when the short-range learning sensor is used, so correct the
debug spew message, and then suppress it when using the standard
long-range sensor.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.
Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than waiting for trigger bits, the formula for which was slightly
messy, and apparently, not actually 100% complete for some remotes, just
call ir_raw_event_handle whenever we finish parsing a chunk of data from
the rx fifo, similar to mceusb, as well as whenever we see an 'end of
signal data' 0x80 packet.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial values of the registers 0x01 and 0x17 are taken from the sensor
table at capture start and updated according to the flag PDN_INV.
Their values are updated at each step of the capture initialization and
memorized for reuse in capture stop.
This patch also fixed automatically some bad hardcoded values of these
registers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The flag PDN_INV indicates that the sensor pin S_PWR_DN has not the same
value as other webcams with the same sensor. For now, only two webcams have
been so detected: the Microsoft's VX1000 and VX3000.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After Mauro's "bttv: Fix locking issues due to BKL removal code" there
are a number of comments that are no longer needed about lock ordering.
Remove them.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression where bttv driver causes oopses when loading, since it
were using some non-initialized mutexes. While it would be possible to
fix the issue, there are some other lock troubles, like to the presence of
lock code at free_btres_lock().
It is possible to fix, but the better is to just use the core-assisted
locking schema. This way, V4L2 core will serialize access to all
ioctl's/open/close/mmap/read/poll operations, avoiding to have two
processes accessing the hardware at the same time. Also, as there's just
one lock, instead of 3, there's no risk of dead locks.
The net result is a cleaner code, with just one lock.
Reported-by: Dan Carpenter <error27@gmail.com>
Reported-by: Brandon Philips<brandon@ifup.org>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Really fix build break on symbol-prefixed archs
[media] Fix Kconfig errors due to two visible menus
i2c/algos: convert Kconfig to use the menu's `visible' keyword
media/video: convert Kconfig to use the menu's `visible' keyword
Revert "i2c: Fix Kconfig dependencies"
kconfig: regen parser
kconfig: add an option to determine a menu's visibility
Drivers should append their name on exported symbols, to avoid
conflicts with allyesconfig:
drivers/staging/built-in.o: In function `format_by_fourcc':
/home/v4l/work_trees/linus/drivers/staging/cx25821/cx25821-video.c:96: multiple definition of `format_by_fourcc'
drivers/media/built-in.o:/home/v4l/work_trees/linus/drivers/media/common/saa7146_video.c:88: first defined here
Let's rename both occurences with a small shellscript:
for i in drivers/staging/cx25821/*.[ch]; do sed s,format_by_fourcc,cx25821_format_by_fourcc,g <$i >a && mv a $i; done
for i in drivers/media/common/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
for i in include/media/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvcvideo driver now locks all ioctls correctly on its own, the BKL
isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The stream mutex protects access to the struct uvc_streaming ctrl,
cur_format and cur_frame fields as well as to the hardware probe
control. Lock it appropriately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mmap() implementation belongs to the video buffers queue, move it
there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callers outside uvc_queue.c should not be forced to lock/unlock the
queue mutex manually. Move the mutex operations inside
uvc_free_buffers().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
uvc_find_control() must be called with the controls mutex locked. Fix
uvc_query_v4l2_menu() accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The unregister function had a race condition with the v4l2_open
function. Ensure that both functions test and clear the REGISTER
flag from within a critical section.
Thanks to Laurent Pinchart for finding this race.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL replacement mutex had some serious performance side-effects on
V4L drivers. It is replaced by a better heuristic that works around the
worst of the side-effects.
Read the v4l2-dev.c comments for the whole sorry story. This is a
temporary measure only until we can convert all v4l drivers to use
unlocked_ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Where reasonable use mutex_lock_interruptible instead of mutex_lock.
Also fix the poll, read and write error codes when called with an unregistered
device (e.g. after a USB device was disconnected). Poll must return
POLLERR|POLLHUP and read/write must return -ENODEV.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also added locking around snd_cx18_pcm_ioctl as a precaution
as requested by Andy Walls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial conversion, this driver used a mutex already.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These drivers could be trivially converted to unlocked_ioctl since they
already did locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the typhoon driver from ioctl to unlocked_ioctl.
When doing this I noticed a bug where curfreq was not initialized correctly
to mutefreq (it wasn't multiplied by 16).
The initialization is now also done before the device node is created.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert ioctl to unlocked_ioctl. Note that for this driver the locking
is done inside the sub-device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert from ioctl to unlocked_ioctl using the v4l2 core lock.
Also removed the 'exclusive access' limitation. There was no need for it
and it violates the v4l2 spec as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted from ioctl to unlocked_ioctl.
This driver already used an internal lock, but it was missing in cadet_open and
cadet_release and it was not used correctly in cadet_read.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch converts a bunch of V4L2 radio drivers to unlocked_ioctl.
These are all simple conversions: most already had a lock and so the ioctl
fop could simply be replaced by unlocked_ioctl.
radio-miropcm20.c was converted to use the new V4L2 core lock.
While doing this work I noticed that many of these drivers initialized
some more fields or muted audio or something like that *after* creating
the device node. This should be done before the device node is created
to prevent problems. Especially hal tends to grab a device node as soon
as it is created.
In one or two cases the mutex_init was even done after the device creation!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The argument isn't used anymore by the functions, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL in the cafe-ccic, via-camera and s5p-fimc drivers.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the new visible Kconfig keyword to avoid producing error for two menus
that are visible only if Tuner/frontend customise options are enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch (as1436) takes care of leftover references to
udev->autosuspend_delay that didn't get removed during the earlier
conversion to the runtime-PM autosuspend API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
mx2-camera got broken during the last merge window. This patch
fixes this and removes some unused variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a followup patch that addresses two minor issues left in the recently
added ov6650 sensor driver, as I've promised to the subsystem maintainer:
- remove a pair of extra brackets,
- drop useless case for not possible v4l2_mbus_pixelcode enum value of 0.
Created against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix an outstanding typo in the recently added driver, as requested by
the subsystem maintainer.
Created against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recent locking related videobuf changes has not been incorporated into the new
OMAP1 camera driver. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The recently added OMAP1 camera driver was not ready for one video queue per
device framework changes. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have two dma engines in MX3 systems: The IPU and the SDMA
engine. We have to check if we got a channel from the correct
engine before proceeding with a channel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason, commit 1aafeb30104a is missing one change that was
included in the email submission.
The sensor configuration must be passed down to the ov7670 subdev.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The entries for those cards are after the generic entries,
so they don't work, in practice. Moving them to happen before the
generic entres fix the issue.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All of the hard problems for BKL removal appear to be solved in the
v4l-dvb/master tree. This removes the BKL from the various open
functions that do not need it, or only use it to protect an
open count.
The zoran driver is nontrivial in this regard, so I introduce
a new mutex that locks both the open/release and the ioctl
functions. Someone with access to the hardware can probably
improve that by using the existing lock in all cases.
Finally, all drivers that still use the locked version of the
ioctl function now get called under a new mutex instead of
the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit a90f933507 accidentally removed
the piece of code setting the i2c algo pointer. Restore it.
That's what happens when you put two code statements on the same
line...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We were forgetting to set up proper return value in success path causing
ir_getkeycode() to fail intermittently:
drivers/media/IR/ir-keytable.c: In function 'ir_getkeycode':
drivers/media/IR/ir-keytable.c:363: warning: 'retval' may be used
uninitialized in this function
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The input-large-scancode patches changed the binary search in
drivers/media/IR/ir-keytable.c to use unsigned integers, but
signed integers are actually necessary for the algorithm to work.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
Changeset 1724c8fa7e added an option to change
the maximum I2C size to 8 bytes. However, it forgot to replace the previous
usage at af9015 to use the newly defined macro value
(TDA18271_16_BYTE_CHUNK_INIT).
A latter changeset (e350d44fed) extended the
possible values for .small_i2c field and, instead of using a random sequence
of numbers, it used a number that makes more sense (e. g. the actual limit,
in terms of bytes).
However, as af9015 were using .small_i2c = 1, this become undefined, and the
restriction of a max size of 16 was gone.
While here, fix the reported msg size at tda18271-common.c.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Few drivers still have assumption that ir_raw_event
consists of duration and pulse flag.
Fix that.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
I managed to trigger a divide by 0 in the v4l compat code
with the mem2mem test module; I suspect perhaps it shouldn't
have been returning a 0 pixel wide picture, but either way it seems
right to guard this divide by 0 in the compatibility layer.
Tested on 2.6.36 (ubuntu build, but the code in this is the same as upstream),
but ***not tested with a real video device***.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
cc: stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pointed out by Bonne Eggleston on the lirc list.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a redundant call to imon_ir_change_protocol -- its already
getting called from ir_input_register. Also do some minor housekeeping
with var names and formatting.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Somehow, I managed to screw things up when reworking the rdev/idev split
patch from David, and started trying to get ir_input_dev from idev
instead of rdev, thus resulting in button presses hanging the system.
This fixes it.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Force smbus communication, disable QCIF mode, and set the correct
clock speed on the OLPC XO-1.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These parameters need to be configurable based on the host system.
They can now be communicated through the s_config call.
The old CONFIG_OLPC_XO_1 selector was not correct; this kind of
arrangement wouldn't allow for a universal kernel that would work on both
laptops.
Certain parts of the probe routine had to be moved later (into s_config),
because we can't do any I/O until we know which I/O method has been
selected through this mechanism.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is AF9015+AF9013+2xMXL5007T.
Tanks to Bernard Giannetti and DigitalNow for the help!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Renura Enterprises Pty Ltd <renura@digitalnow.com.au>
Cc: Bernard Giannetti <thebernmeister@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Read all remote controller registers at once to reduce USB remote polling traffic.
Use .rc_codes() to disable / enable remote polling instead of .rc_query().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Digital Everywhere firmware have the shortcoming that ca_info_enq and
ca_info are not supported. This means that we can never retrieve the correct
ca_system_id to present in the CI message CA_INFO. Currently the driver uses
the application id retrieved using app_info_req and app_info, but this id
only match the correct ca_system_id as given in ca_info in some cases.
This patch adds a parameter to the driver in order for the user to override
what will be returned in the CA_INFO CI message. Up to four ca_system_ids can
be specified.
This is needed for users with CAMs that have different manufacturer id and
ca_system_id and that uses applications that take this into account, like
MythTV.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Lawrence Rust <lawrence@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- serialize the suspend and resume functions using the global lock.
- do not call usb_autopm_put_interface after a disconnect.
- fix a race when disconnecting the device.
Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: David Ellingsworth<david@identd.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Indent the branch of an if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These include
-later kill of usb_buffer to avoid kernel crash on hot unplugging.
-DiSEqC functions.
-LNB Power switch
-Faster channel change.
-support for LG tuner on LME2510C.
-firmware switching for LG tuner.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
> From: Dan Carpenter [mailto:error27@gmail.com]
>
> These are signed so instead of being 1 and 0 as intended they are -1 and
> 0. It doesn't cause a bug in the current code but Sparse warns about
> it:
>
> drivers/media/video/s5p-fimc/fimc-core.h:226:28:
> error: dubious one-bit signed bitfield
> struct fimc_scaler {
> - int scaleup_h:1;
> - int scaleup_v:1;
> - int copy_mode:1;
> - int enabled:1;
> + unsigned int scaleup_h:1;
> + unsigned int caleup_v:1;
> + unsigned int copy_mode:1;
> + unsigned int enabled:1;
In general I agree, however this patch would change scaleup_v:1
to caleup_v, so it cannot be applied in current form.
Here is the corrected patch:
Reported-by: Dan Carpenter <error27@gmail.com<
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was an unlock missing if kzalloc() failed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
The sub-devices without a listed module name don't result in and I2C
sub-device being created, as they either are IR devices or don't have an
I2C address listed. It's thus safe to rely on modaliases only.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the cx18 driver
uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
The sub-devices without a listed module name don't result in and I2C
sub-device being created, as they either are IR devices or don't have an
I2C address listed. It's thus safe to rely on modaliases only.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the ivtv driver
uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, don't use the module names hardcoded in platform
data by passing a NULL module name to those functions.
The only platform using the VPIF capture device (DM646x EVM) hardcodes
the module names to invalid values (tvp514x-0 and tvp514x-1). As this is
already broken, there's no risk of breaking it more.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, don't use the module names hardcoded in platform
data by passing a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the vpif_display
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, don't use the module names hardcoded in platform
data by passing a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the vpfe_capture
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the soc_camera
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
As no board seems to use this driver, no platform data has been checked.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the sh_vou
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the pvrusb2
driver uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-By: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the zoran driver
uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When creating a new sub-device, The V4L I2C subdev API has historically
required drivers to pass the name of the module that implements support
for the I2C device.
I2C modules can be loaded based on modaliases instead of the module
name. As the I2C device type name is already available to the
v4l2_i2c_new_subdev* functions, make the module name argument optional
and create a modalias based on the type name when no module name is
provided.
All in-tree drivers call those functions with a non-NULL module name
argument, this change is thus harmless.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was supposed to be an unlock on the error path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Cc: Palash Bandyopadhyay < palash.bandyopadhyay@conexant.com>
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes a gcc warning:
drivers/media/video/cx88/cx88-video.c:772:
warning: ‘core’ may be used uninitialized in this function
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch allows this device successfully to show video, at least from
its composite input.
I have no information about the true hardware contents of this device and so
this patch is based solely on fiddling with things until it worked. The
chip appears to be em2860, and the closest device with equivalent inputs
is the Typhoon DVD Maker. Copying the settings for that device appears
to do the trick. That's what this patch does.
[mchehab@redhat.com: update CARDLIST.em28xx accordingly, via script]
Signed-off-by: Adrian Taylor <adrian.taylor@realvnc.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provides more complete debug spew, parses individual commands and raw IR
data one chunk at a time.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
And replace usage of hex values w/symbolic names wherever possible
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is better to use a per-model device name, especially on
multi-function devices like Polaris. So, allow overriding the
default name at the mceusb model table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Especially when used with Polaris boards, devices may have different
types of remotes shipped. So, we need a per-model rc-map.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
The previous logic needed duplicate USB table structs, one to store
the list of the devices, and 3 sets of other structs, to store the
quirks list.
With this change, devices that require expecial quirks just need to
have a .driver_info = <quirk entry>.
It also allows adding some extra quirks, like per-model RC tables.
As a bonus, this patch reduced in 10% the data segment size:
text data bss dec hex filename
15487 5008 4 20499 5013 old/mceusb.ko
15438 4496 4 19938 4de2 new/mceusb.ko
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Switch to a state machine that properly handles all incoming urb data
packets, and reads much cleaner and corrects some minor parsing errors
that were hindering decode on cx231xx/Polaris integrated IR. Also tested
with four different mceusb variants, and works perfectly with all of
them (at least for the rc6a mce remotes).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Fixes an oops when an lirc driver that doesn't provide its own fops is
unplugged while the lirc cdev is open. Tested with lirc_igorplugusb,
with a special thanks to Timo Boettcher for providing the test hardware.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Can't explain it (yet), but I've seen the 'get irctl via private_data'
setup fail for a number of people (ioctl called before its filled in?),
so lets go back to a variant of the old way, but one that still works
with unlocked_ioctl.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If an lirc device driver doesn't specify its own fops, we set set
ir->cdev.owner to THIS_MODULE. If it does specify its own fops, we
set ir->cdev.owner to ir->d.owner. Subsequent module_{get,put} calls
should be using ir->cdev.owner, not ir->d.owner.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use names that clearly identify functions as lirc functions.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'config' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
BKL: introduce CONFIG_BKL.
dabusb: remove the BKL
sunrpc: remove the big kernel lock
init/main.c: remove BKL notations
blktrace: remove the big kernel lock
rtmutex-tester: make it build without BKL
dvb-core: kill the big kernel lock
dvb/bt8xx: kill the big kernel lock
tlclk: remove big kernel lock
fix rawctl compat ioctls breakage on amd64 and itanic
uml: kill big kernel lock
parisc: remove big kernel lock
cris: autoconvert trivial BKL users
alpha: kill big kernel lock
isapnp: BKL removal
s390/block: kill the big kernel lock
hpet: kill BKL, add compat_ioctl
The errors were found by checkpatch.pl. Most fixes are:
- remove spaces followed by TAB(s),
- split lines greater than 80 characters,
- move most '{'s from start of line to end of previous line.
(Some '{'s at start of line remain when the '}'s are on the same line)
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PO2030N sensor chip found in hama AC-150 webcam supports horizontal
and vertical flipping the image by hardware.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number 0xdd is used for marking delay init sequence steps.
Replace 0xdd values only if the meaning is delay.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by commit d5aa3856fd
removing the probe sequence of hv7131r with bridge sn9c120 and so, letting
the sensor inactive.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by commit 23a98274cc
applying values of sensor sp80708 to sensors hv7131r and mi0360.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for the video capture port on VIA integrated chipsets. This
version has a remaining OLPCism or two and expects to be talking to an
ov7670; those can be improved as the need arises.
This work was supported by the One Laptop Per Child project.
Thanks to Laurent Pinchart for a number of useful comments.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The QVGA mode has a green horizontal line on the left hand side, and a red
(or sometimes blue) vertical line at the bottom. Tweak the visible area
to remove them.
Thanks to Mauro for explaining how to fix this.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes the name of the av7110 driver from the
generic "dvb" to "av7110", to be descriptive of the driver.
I've included Oliver Endriss's ack from the original post, which
contained a mangled patch. The content of the patch is unchanged.
Signed-off-by: Derek Kelly <user.vdr@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Polaris design uses MCE support. Instead of reinventing the wheel,
just let mceusb handle the remote controller.
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Sri Devi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Interface 0 is used by IR. The current driver starts initializing
on it, finishing on interface 6. Change the logic to only handle
interface 1. This allows another driver (mceusb) to take care of
the IR interface.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Sri Devi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For now, it adds support for Conexant EVK and for Pixelview.
We should probably find a better way to specify all Conexant
Polaris devices, to avoid needing to repeat this setup on
both mceusb and cx231xx-cards.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Sri Devi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With all the patches we have queued in the BKL removal tree, only a
few dozen modules are left that actually rely on the BKL, and even
there are lots of low-hanging fruit. We need to decide what to do
about them, this patch illustrates one of the options:
Every user of the BKL is marked as 'depends on BKL' in Kconfig,
and the CONFIG_BKL becomes a user-visible option. If it gets
disabled, no BKL using module can be built any more and the BKL
code itself is compiled out.
The one exception is file locking, which is practically always
enabled and does a 'select BKL' instead. This effectively forces
CONFIG_BKL to be enabled until we have solved the fs/lockd
mess and can apply the patch that removes the BKL from fs/locks.c.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is just unnessesary, and now more logical
Also a lot of refactoring
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new event types for timeout & carrier report
Move timeout handling from ir_raw_event_store_with_filter to
ir-lirc-codec, where it is really needed.
Now lirc bridge ensures proper gap handling.
Extend lirc bridge for carrier & timeout reports
Note: all new ir_raw_event variables now should be initialized
like that: DEFINE_IR_RAW_EVENT(ev);
To clean an existing event, use init_ir_raw_event(&ev);
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patches adjusts the tuner delay to be longer in response to
several users experiencing tuner timeouts. This change fixes that
problem and allows those users to be able to tune.
Signed-off-by: Derek Kelly <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch updates the name of the dvb-usb-gp8psk driver
from "Genpix 8psk-to-USB2 DVB-S" to "Genpix DVB-S".
The old name doesn't reflect newer devices such as the
Skywalker line which also user this driver.
Signed-off-by: Derek Kelly <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the AUX_PLL in cx2583x chips which is available in
those although the audio part of the chip is not.
The AUX_PLL is used at least by Terratec in their Grabster AV400 device.
Signed-off-by: Sven Barth <pascaldragon@googlemail.com>
Acked-by: Mike Isely <isely@pobox.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes these build errors and warnings:
drivers/media/video/cx231xx/cx231xx-417.c: In function 'cx231xx_load_firmware':
drivers/media/video/cx231xx/cx231xx-417.c:943: error: implicit declaration of function 'vmalloc'
drivers/media/video/cx231xx/cx231xx-417.c:943: warning: cast to pointer from integer of different size
drivers/media/video/cx231xx/cx231xx-417.c:950: warning: cast to pointer from integer of different size
drivers/media/video/cx231xx/cx231xx-417.c:1039: error: implicit declaration of function 'vfree'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
The switch to the new control framework caused a regression where the audio was
no longer unmuted after the carrier scan finished.
The original code attempted to set the volume control to its current value in
order to have the set-volume control code to be called that handles the volume
and muting. However, the framework will not call that code unless the new volume
value is different from the old.
Instead we now call msp_s_ctrl directly.
It is a bit of a hack: we really need a v4l2_ctrl_refresh_ctrl function for this
(or something along those lines).
Thanks to Andy Walls for bisecting this and to Shane Shrybman for reporting it!
Reported-by: Shane Shrybman <shrybman@teksavvy.com>
Thanks-to: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When audio is present, some alternate settings were skipped.
This prevented some webcams to work, especially when bulk transfer was used.
This patch permits to use the last or only alternate setting.
Reported-by: Antonio Ospite <ospite@studenti.unina.it>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Siliconfile SR030PC30 VGA camera fails to compile with this error:
drivers/media/video/sr030pc30.c: In function ‘sr030pc30_probe’:
drivers/media/video/sr030pc30.c:834: error: implicit declaration of function ‘kzalloc’
drivers/media/video/sr030pc30.c:834: warning: assignment makes pointer from integer without a cast
drivers/media/video/sr030pc30.c: In function ‘sr030pc30_remove’:
drivers/media/video/sr030pc30.c:858: error: implicit declaration of function ‘kfree’
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
refine the firmware version test and print the version only once
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hauppauge released different firmwares using the same version number.
The firmware date can be used to identify the exact driver/firmware
combination.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed problem with DiSEqC communication. The message was wrongly modulated,
so the DiSEqC switch was not work.
This patch fixes DiSEqC messages, simple tone burst and tone on/off.
I verified it with osciloscope against the DiSEqC documentation.
Interface: PCI DVB-S TV tuner TeVii S420
Kernel: 2.6.32-24-generic (UBUNTU 10.4)
Signed-off-by: Josef Pavlik <josef@pavlik.it>
Tested-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch add support of TwinHan 1027 DVB-S card.
Refreshed version of https://patchwork.kernel.org/patch/79753/ patch.
(adapted for the new IR system), still works.
DVB-S support come from a patch originally authored by
Manu Abraham (abraham.manu@gmail.com).
IR Port support were added by Sergey.
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also sets to 0 the sequence of the first frame.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an I2C/v4l2-subdev driver for Siliconfile SR030PC30 VGA
camera sensor with Image Signal Processor. SR030PC30 is
the low resolution camera sensor on Samsung Aquila boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable FIMC operation on S5PC210 (S5PV310) SoCs. This a minimal
adaptation to obtain functionality of older FIMC IP revisions
(S5PC100, S5PC110) on S5PC210 SOcs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a video device driver per each FIMC entity to support
the camera capture input mode. Video capture node is registered
only if CCD sensor data is provided through driver's platfrom data
and board setup code.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not necessary to lock both capture and output buffer queue while
setting format for single queue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to errorneous swapping of image dimensions the rotation
control was not handled properly in subsequent calls.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register access functions refactored for camera capture interface
control. Removed the workqueue since it was only useful for FIFO
output mode which is not supported at this time.
Fixed errors on module unload. Comments and whitespace cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No need to duplicate default .get_parm() and .set_parm() operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds an initial driver for the IMXъ74 image sensor from Sony.
Lacking documentation, only very basic functionality in one specific image
format has been implemented and tested.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for g_parm / s_parm operations to the SoC Camera
framework. It is usefull for checking/setting camera frame rate.
Example usage can be found in the previous patch from this series,
"SoC Camera: add driver for OV6650 sensor".
Created and tested against linux-2.6.36-rc3 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides a V4L2 SoC Camera driver for OV6650 camera sensor, found
on OMAP1 SoC based Amstrad Delta videophone.
Since I have no experience with camera sensors, and the sensor documentation I
was able to find was not very comprehensive, I left most settings at their
default (reset) values, except for:
- those required for proper mediabus parameters and picture geometry and
format setup,
- those used by controls.
Resulting picture quality may be far from perfect, but better than nothing.
In order to be able to get / set the sensor frame rate from userspace, I
decided to provide two not yet SoC camera supported operations, g_parm and
s_parm. These can be used after applying patch 4/6 from this series,
"SoC Camera: add support for g_parm / s_parm operations".
Created and tested against linux-2.6.36-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a V4L2 driver for TI OMAP1 SoC camera interface.
Both videobuf-dma versions are supported, contig and sg, selectable with a
module option. The former uses less processing power, but often fails to
allocate contignuous buffer memory. The latter is free of this problem, but
generates tens of DMA interrupts per frame. If contig memory allocation ever
fails, the driver falls back to sg automatically on next open, but still can
be switched back to contig manually. Both paths work stable for me, even
under heavy load, on my OMAP1510 based Amstrad Delta videophone, that is the
oldest, least powerfull OMAP1 implementation.
The interface generally works in pass-through mode. Since input data byte
endianess can be swapped, it provides up to two v4l2 pixel formats per each of
several soc_mbus formats that have their swapped endian counterparts.
Boards using this driver can provide it with the following platform data:
- if and what freqency clock is expected by an on-board camera sensor,
- what is the maximum pixel clock that should be accepted from the sensor,
- what is the polarity of the sensor provided pixel clock,
- if the interface GPIO line is connected to a sensor reset/powerdown input
and what is the input polarity.
Created and tested against linux-2.6.36-rc5 on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove usage of the BKL and instead used video_set_drvdata() during
open fops.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove V4L2_CAP_STREAMING capability flag, we don't support
the ioctls. It breaks VLC otherwise.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are lots of checkpatch complains about:
ERROR: space prohibited after that open parenthesis '('
ERROR: space prohibited after that open square bracket '['
ERROR: space prohibited before that close parenthesis ')'
ERROR: space prohibited before that close square bracket ']'
This script should fix all of them:
for i in drivers/media/video/saa7164/*.[ch]; do cat $i|perl -ne 's/\[\ +(.*)/[$1/; s/\ +\]/$1\]/g; s/\(\ +(.*)/($1/g; s/\ +\)/$1)/g; print $_;' >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with CodingStyle, drivers shouldn't use typedef, except on very
special cases. This is not the case of saa7164. So, convert all usecases
to struct/enum.
After changing the saa7164-types.h, all we need to do is to run those scripts
to fix all occurrences of the bad types and double check/fix everything that
might be broken after the test (of course, I did a small script to generate those scripts).
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmBusType_t/enum tmBusType/; print " \>a \&\& mv a tmBusType; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResCmd_t/enum tmComResCmd/; print " \>a \&\& mv a tmComResCmd; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResTermType_t/enum tmComResTermType/; print " \>a \&\& mv a tmComResTermType; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmBufferFlag_t/enum tmBufferFlag/; print " \>a \&\& mv a tmBufferFlag; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResHWDescr_t/struct tmComResHWDescr/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResInterfaceDescr_t/struct tmComResInterfaceDescr/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResBusDescr_t/struct tmComResBusDescr/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmBusType_t/struct tmBusType/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResBusInfo_t/struct tmComResBusInfo/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResInfo_t/struct tmComResInfo/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResCmd_t/struct tmComResCmd/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmDescriptor_t/struct tmDescriptor/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResDescrHeader_t/struct tmComResDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResExtDevDescrHeader_t/struct tmComResExtDevDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResGPIO_t/struct tmComResGPIO/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResPathDescrHeader_t/struct tmComResPathDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResTermType_t/struct tmComResTermType/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResAntTermDescrHeader_t/struct tmComResAntTermDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResTunerDescrHeader_t/struct tmComResTunerDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmBufferFlag_t/struct tmBufferFlag/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmBuffer_t/struct tmBuffer/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmHWStreamParameters_t/struct tmHWStreamParameters/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmStreamParameters_t/struct tmStreamParameters/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResDMATermDescrHeader_t/struct tmComResDMATermDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResTSFormatDescrHeader_t/struct tmComResTSFormatDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResSelDescrHeader_t/struct tmComResSelDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResProcDescrHeader_t/struct tmComResProcDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResEncVideoBitRate_t/struct tmComResEncVideoBitRate/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResEncVideoInputAspectRatio_t/struct tmComResEncVideoInputAspectRatio/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResEncVideoGopStructure_t/struct tmComResEncVideoGopStructure/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResEncoderDescrHeader_t/struct tmComResEncoderDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResAFeatureDescrHeader_t/struct tmComResAFeatureDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResAudioDefaults_t/struct tmComResAudioDefaults/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResEncAudioBitRate_t/struct tmComResEncAudioBitRate/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResTunerStandard_t/struct tmComResTunerStandard/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResTunerStandardAuto_t/struct tmComResTunerStandardAuto/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResPSFormatDescrHeader_t/struct tmComResPSFormatDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResVBIFormatDescrHeader_t/struct tmComResVBIFormatDescrHeader/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResProbeCommit_t/struct tmComResProbeCommit/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResDebugSetLevel_t/struct tmComResDebugSetLevel/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmComResDebugGetData_t/struct tmComResDebugGetData/g; print " $i >a && mv a $i; done
for i in drivers/media/video/saa7164/*.[ch]; do perl -ne "s/tmFwInfoStruct_t/struct tmFwInfoStruct/g; print " $i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/saa7164/saa7164-buffer.c: In function ‘saa7164_buffer_display’:
drivers/media/video/saa7164/saa7164-buffer.c:76: warning: cast to pointer from integer of different size
drivers/media/video/saa7164/saa7164-buffer.c:78: warning: cast to pointer from integer of different size
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... Also disable collection of messages via kernel thread.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark buffers free when the dvb dma engine stops.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller
Jean-François Moine
Hans de Goede
Malcolm Priestley
Daniel Drake
Joe Perches
Mauro Carvalho Chehab
Linus Torvalds
Guennadi Liakhovetski
Tejun Heo
Greg Kroah-Hartman
Jarod Wilson
Dan Carpenter
Paul Bender
Sylwester Nawrocki
Baruch Siach
Brandon Philips
Mauro Carvalho Chehab
Laurent Pinchart
Hans Verkuil
Arnaud Lacombe
Alan Stern
Arnd Bergmann
Jean Delvare
Wolfram Sang
Sascha Hauer
Janusz Krzysztofik
Dmitri Belimov
Dmitry Torokhov
David Härdeman
Zimny Lech
Maxim Levitsky
Dr. David Alan Gilbert
Antti Palosaari
Henrik Kurelid
lawrence rust
Matti Aaltonen
Julia Lawall
Adrian Taylor
Németh Márton
Jonathan Corbet
Derek Kelly
Michel Garnier
Sven Barth
Stephen Rothwell
Janne Grunau
Alan Young
James M McLaren
Andy Shevchenko
Pawel Osciak
Sergey Ivanov
Michael Grzeschik
Steven Toth
Gavin Hurlbut