* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.26: (1090 commits)
[NET]: Fix and allocate less memory for ->priv'less netdevices
[IPV6]: Fix dangling references on error in fib6_add().
[NETLABEL]: Fix NULL deref in netlbl_unlabel_staticlist_gen() if ifindex not found
[PKT_SCHED]: Fix datalen check in tcf_simp_init().
[INET]: Uninline the __inet_inherit_port call.
[INET]: Drop the inet_inherit_port() call.
SCTP: Initialize partial_bytes_acked to 0, when all of the data is acked.
[netdrvr] forcedeth: internal simplifications; changelog removal
phylib: factor out get_phy_id from within get_phy_device
PHY: add BCM5464 support to broadcom PHY driver
cxgb3: Fix __must_check warning with dev_dbg.
tc35815: Statistics cleanup
natsemi: fix MMIO for PPC 44x platforms
[TIPC]: Cleanup of TIPC reference table code
[TIPC]: Optimized initialization of TIPC reference table
[TIPC]: Remove inlining of reference table locking routines
e1000: convert uint16_t style integers to u16
ixgb: convert uint16_t style integers to u16
sb1000.c: make const arrays static
sb1000.c: stop inlining largish static functions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
[SCSI] iscsi: bidi support for iscsi_tcp
[SCSI] iscsi: bidi support at the generic libiscsi level
[SCSI] iscsi: extended cdb support
[SCSI] zfcp: Fix error handling for blocked unit for send FCP command
[SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
[SCSI] zfcp: fix 31 bit compile warnings
[SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
[SCSI] bsg: remove minor in struct bsg_device
[SCSI] bsg: use better helper list functions
[SCSI] bsg: replace kobject_get with blk_get_queue
[SCSI] bsg: takes a ref to struct device in fops->open
[SCSI] qla1280: remove version check
[SCSI] libsas: fix endianness bug in sas_ata
[SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
[SCSI] aacraid: Do not describe check_reset parameter with its value
[SCSI] aacraid: Fix down_interruptible() to check the return value
[SCSI] sun3_scsi_vme: add MODULE_LICENSE
[SCSI] st: rename flush_write_buffer()
[SCSI] tgt: use KMEM_CACHE macro
[SCSI] initio: fix big endian problems for auto request sense
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (43 commits)
firewire: cleanups
firewire: fix synchronization of gap counts
firewire: wait until PHY configuration packet was transmitted (fix bus reset loop)
firewire: remove unused struct member
firewire: use bitwise and to get reg in handle_registers
firewire: replace more hex values with defined csr constants
firewire: reread config ROM when device reset the bus
firewire: replace static ROM cache by allocated cache
firewire: fw-ohci: work around generation bug in TI controllers (fix AV/C and more)
firewire: fw-ohci: extend logging of bus generations and node ID
firewire: fw-ohci: conditionally log busReset interrupts
firewire: fw-ohci: don't append to AT context when it's not active
firewire: fw-ohci: log regAccessFail events
firewire: fw-ohci: make sure HCControl register LPS bit is set
firewire: fw-ohci: missing PPC PMac feature calls in failure path
firewire: fw-ohci: untangle a mixed unsigned/signed expression
firewire: debug interrupt events
firewire: fw-ohci: catch self_id_count == 0
firewire: fw-ohci: add self ID error check
firewire: fw-ohci: refactor probe, remove, suspend, resume
...
This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Bernhard Kaindl <bk@suse.de>
* 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc:
Remove DEBUG_SEMAPHORE from Kconfig
Improve semaphore documentation
Simplify semaphore implementation
Add down_timeout and change ACPI to use it
Introduce down_killable()
Generic semaphore implementation
Add semaphore.h to kernel_lock.c
Fix quota.h includes
This patch adds in the ability to compile the kgdb internal test
string into the kernel so as to run the tests at boot without changing
the kernel boot arguments. This patch also changes all the error
paths to invoke WARN_ON(1) which will emit the line number of the file
and dump the kernel stack when an error occurs.
You can disable the tests in a kernel that is built this way
using "kgdbts="
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds regression tests for testing the kgdb core and arch
specific implementation.
The kgdb test suite is designed to be built into the kernel and not as
a module because it uses a number of low level kernel and kgdb
primitives which should not be exported externally.
The kgdb test suite is designed as a KGDB I/O module which
simulates the communications that a debugger would have with kgdb.
The tests are broken up in to a line by line and referenced here as
a "get" which is kgdb requesting input and "put" which is kgdb
sending a response.
The kgdb suite can be invoked from the kernel command line
arguments system or executed dynamically at run time. The test
suite uses the variable "kgdbts" to obtain the information about
which tests to run and to configure the verbosity level. The
following are the various characters you can use with the kgdbts=
line:
When using the "kgdbts=" you only choose one of the following core
test types:
A = Run all the core tests silently
V1 = Run all the core tests with minimal output
V2 = Run all the core tests in debug mode
You can also specify optional tests:
N## = Go to sleep with interrupts of for ## seconds
to test the HW NMI watchdog
F## = Break at do_fork for ## iterations
S## = Break at sys_open for ## iterations
NOTE: that the do_fork and sys_open tests are mutually exclusive.
To invoke the kgdb test suite from boot you use a kernel start
argument as follows:
kgdbts=V1 kgdbwait
Or if you wanted to perform the NMI test for 6 seconds and do_fork
test for 100 forks, you could use:
kgdbts=V1N6F100 kgdbwait
The test suite can also be invoked at run time with:
echo kgdbts=V1N6F100 > /sys/module/kgdbts/parameters/kgdbts
Or as another example:
echo kgdbts=V2 > /sys/module/kgdbts/parameters/kgdbts
When developing a new kgdb arch specific implementation or
using these tests for the purpose of regression testing,
several invocations are required.
1) Boot with the test suite enabled by using the kernel arguments
"kgdbts=V1F100 kgdbwait"
## If kgdb arch specific implementation has NMI use
"kgdbts=V1N6F100
2) After the system boot run the basic test.
echo kgdbts=V1 > /sys/module/kgdbts/parameters/kgdbts
3) Run the concurrency tests. It is best to use n+1
while loops where n is the number of cpus you have
in your system. The example below uses only two
loops.
## This tests break points on sys_open
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
echo kgdbts=V1S10000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
fg # and hit control-c
## This tests break points on do_fork
while [ 1 ] ; do date > /dev/null ; done &
while [ 1 ] ; do date > /dev/null ; done &
echo kgdbts=V1F1000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
kgdb core code. Handles the protocol and the arch details.
[ mingo@elte.hu: heavily modified, simplified and cleaned up. ]
[ xemul@openvz.org: use find_task_by_pid_ns ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Alpha and FRV mutexes had an option to print lots of debugging messages
in their semaphore implementation. This feature has not been carried
over to the generic semaphores, so remove the stale Kconfig option.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
kernel_lock.c uses DECLARE_MUTEX, up() and down() without explicitly
including asm/semaphore.h. This is fragile and leaves it vulnerable
to breakage during header reorganisations.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
There is a potential bug in __lmb_alloc_base where we subtract `size'
from the base address of a reserved region without checking whether
the subtraction could wrap around and produce a very large unsigned
value. In fact it probably isn't possible to hit the bug in practice
since it would only occur in the situation where we can't satisfy the
allocation request and there is a reserved region starting at 0.
This fixes the potential bug by breaking out of the loop when we get
to the point where the base of the reserved region is less than the
size requested. This also restructures the loop to be a bit easier to
follow.
The same logic got copied into lmb_alloc_nid_unreserved, so this makes
a similar change there. Here the bug is more likely to be hit because
the outer loop (in lmb_alloc_nid) goes through the memory regions in
increasing order rather than decreasing order as __lmb_alloc_base
does, and we are therefore more likely to hit the case where we are
testing against a reserved region with a base address of 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes no semantic changes. It fixes the whitespace and formatting
a bit, gets rid of a local DBG macro and uses the equivalent pr_debug
instead, and restructures one while loop that had a function call and
assignment in the condition to be a bit more readable. Some comments
about functions being called with relocation disabled were also removed
as they would just be confusing to most readers now that the code is
in lib/.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A variant of lmb_alloc() that tries to allocate memory on a specified
NUMA node 'nid' but falls back to normal lmb_alloc() if that fails.
The caller provides a 'nid_range' function pointer which assists the
allocator. It is given args 'start', 'end', and pointer to integer
'this_nid'.
It places at 'this_nid' the NUMA node id that corresponds to 'start',
and returns the end address within 'start' to 'end' at which memory
assosciated with 'nid' ends.
This callback allows a platform to use lmb_alloc_nid() in just
about any context, even ones in which early_pfn_to_nid() might
not be working yet.
This function will be used by the NUMA setup code on sparc64, and also
it can be used by powerpc, replacing it's hand crafted
"careful_allocation()" function in arch/powerpc/mm/numa.c
If x86 ever converts it's NUMA support over to using the LMB helpers,
it can use this too as it has something entirely similar.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
count_partial() is used by both slabinfo and the sysfs proc support. Move
the function directly before the beginning of the sysfs code so that it can
be easily found. Rework the preprocessor conditional to take into account
that slub sysfs support depends on CONFIG_SYSFS *and* CONFIG_SLUB_DEBUG.
Make CONFIG_SLUB_STATS depend on CONFIG_SLUB_DEBUG and CONFIG_SYSFS. There
is no point of keeping statistics if no one can restrive them.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Shift of a LE value seems strange, probably meant to shift the cpu-order
variable as in the prvious section of the switch statement.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds new three helper functions to copy data between an SG
list and a linear buffer.
- sg_copy_from_buffer copies data from linear buffer to an SG list
- sg_copy_to_buffer copies data from an SG list to a linear buffer
When the APIs copy data from a linear buffer to an SG list,
flush_kernel_dcache_page is called. It's not necessary for everyone
but it's a no-op on most architectures and in general the API is not
used in performance critical path.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Let it update the state of all CPUs. The network stack goes
into pains to feed the current IP addresses in, but it is not very
effective if that is only done for some random CPU instead of all.
So change it to feed bits into all CPUs. I decided to do that lockless
because well somewhat random results are ok.
v2: Drop rename so that this patch doesn't depend on x86 maintainers
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This does not look good, but there is no other choice. The compilation
without CONFIG_NET is broken and can not be fixed with ease.
After that there is no need for the following commits:
1567ca7eec3edf8fa5cc2d38f9a4f8
Revert them.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Lord wrote:
>
> On boot, syslog is flooded with "uevent: unsupported action-string;" messages.
..
> Mar 28 14:43:29 shrimp kernel: tty ptyqd: uevent: unsupported
> action-string; this will be ignored in a future kernel version
> Mar 28 14:43:29 shrimp kernel: tty ptyqe: uevent: unsupported
> action-string; this will be ignored in a future kernel version
> Mar 28 14:43:29 shrimp kernel: tty ptyqf: uevent: unsupported
> action-string; this will be ignored in a future kernel version
> Mar 28 14:43:29 shrimp kernel: tty ptyr0: uevent: unsupported
> action-string; this will be ignored in a future kernel version
..
These messages are a regression compared with 2.6.24, which did not
flood the syslog with them.
The actual underlying problem was introduced in 2.6.23, when somebody
made the string parsing no longer accept nul-terminated strings as a
valid input to store_uevent().
Eg. "add\0" was valid prior to 2.6.23, where the code regressed to
require "add" without the '\0'.
This patch fixes the 2.6.23 / 2.6.24 regressions, by having the code
once again tolerate the trailing '\0', if present.
According to GregKH, this mainly affects older Ubuntu systems, such as
the one I have here that requires this fix.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The knock-out. The pcounter abstraction is not used any longer in the
kernel.
Not sure whether this should go via netdev tree, but as far as I
remember it was added via this one, and besides Eric thinks that
Andrew shouldn't mind this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix broken compilation for 'allnoconfig'. This was introduced by
Introduced by commit 1218854afa ("[NET]
NETNS: Omit seq_net_private->net without CONFIG_NET_NS.")
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".
Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: H. Peter Anvin <hpa@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers need to reserve all PCI BARs to prevent other drivers
misusing unoccupied BARs. pcim_iomap_regions_request_all() requests
all BARs and iomap specified BARs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 681cc5cd3e ("iommu sg merging:
swiotlb: respect the segment boundary limits") introduced two
possibilities for entering an endless loop in lib/swiotlb.c:
- if max_slots is zero (possible if mask is ~0UL)
- if the number of slots requested fits into a swiotlb segment, but is
too large for the part of a segment which remains after considering
offset_slots
This fixes them
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
debugfs: fix sparse warnings
Driver core: Fix cleanup when failing device_add().
driver core: Remove dpm_sysfs_remove() from error path of device_add()
PM: fix new mutex-locking bug in the PM core
PM: Do not acquire device semaphores upfront during suspend
kobject: properly initialize ksets
sysfs: CONFIG_SYSFS_DEPRECATED fix
driver core: fix up Kconfig text for CONFIG_SYSFS_DEPRECATED
iommu_is_span_boundary is used internally in the IOMMU helper
(lib/iommu-helper.c), a primitive function that judges whether a memory area
spans LLD's segment boundary or not.
It's difficult to convert some IOMMUs to use the IOMMU helper but
iommu_is_span_boundary is still useful for them. So this patch exports it.
This is needed for the parisc iommu fixes.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kset_initialize was calling kobject_init_internal() which didn't
initialize the kobject as well as kobject_init() was. So have
kobject_init() call kobject_init_internal() and move the logic to
initalize the kobject there.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lib/vsprintf.c: Fix bug omitting minus sign of numbers (module_param)
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make LKDTM depend on BLOCK to prevent build failures with certain configs.
Signed-off-by: Chris Snook <csnook@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We introduced a bug in fixing lmb_add_region to handle an initial
region being non-zero. Before that fix it was impossible to insert a
region at the head of the list since the first region always started
at zero.
Now that its possible for the first region to be non-zero we need to
check to see if the new region should be added at the head and if so
actually add it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We started to see patches enabling this - so explain why
it is disabled and the condition to enable it again.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Convert the lmb code to use u64 instead of unsigned long for physical
addresses and sizes. This is needed to support large amounts of RAM
on 32-bit systems that support 36-bit physical addressing.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we add to an empty lmb region with a non-zero base we will not
coalesce the number of regions down to one. This causes problems on
ppc32 for the memory region as its assumed to only have one region.
We can fix this be easily specially casing the initial add to just
replace the dummy region.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check lmb_add_region() for errors, it can run out
of regions etc.
Also, the size needs to be padded to the given alignment
or else the lmb.reserved regions don't get expanded and
instead we get tons of holes and eventually run out of
regions prematurely.
Signed-off-by: David S. Miller <davem@davemloft.net>
In arch/x86/boot/printf.c gets rid of unused tail of digits: const char
*digits = "0123456789abcdefghijklmnopqrstuvwxyz"; (we are using 0-9a-f
only)
Uses smaller/faster lowercasing (by ORing with 0x20)
if we know that we work on numbers/digits. Makes
strtoul smaller, and also we are getting rid of
static const char small_digits[] = "0123456789abcdefx";
static const char large_digits[] = "0123456789ABCDEFX";
since this works equally well:
static const char digits[16] = "0123456789ABCDEF";
Size savings:
$ size vmlinux.org vmlinux
text data bss dec hex filename
877320 112252 90112 1079684 107984 vmlinux.org
877048 112252 90112 1079412 107874 vmlinux
It may be also a tiny bit faster because code has less
branches now, but I doubt it is measurable.
[ hugh@veritas.com: uppercase pointers fix ]
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Other than the defconfigs, remove the entry in compiler-gcc4.h,
Kconfig.debug and feature-removal-schedule.txt.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
lib/scatterlist.c is needed by drivers/media/video/videobuf-dma-sg.c, and
we would like to be able to use the latter without PCI too, for example, on
PXA270 ARM CPU. It is then possible to create a configuration with
CONFIG_BLOCK=n, where only module code will need scatterlist.c. Therefore
it must be in obj-y.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, for every sysfs node, the callers will be responsible for
implementing store operation, so many many callers are doing duplicate
things to validate input, they have the same mistakes because they are
calling simple_strtol/ul/ll/uul, especially for module params, they are
just numeric, but you can echo such values as 0x1234xxx, 07777888 and
1234aaa, for these cases, module params store operation just ignores
succesive invalid char and converts prefix part to a numeric although input
is acctually invalid.
This patch tries to fix the aforementioned issues and implements
strict_strtox serial functions, kernel/params.c uses them to strictly
validate input, so module params will reject such values as 0x1234xxxx and
returns an error:
write error: Invalid argument
Any modules which export numeric sysfs node can use strict_strtox instead of
simple_strtox to reject any invalid input.
Here are some test results:
Before applying this patch:
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000g > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000gggggggg > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 010000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0100008 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 010000aaaaa > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]#
After applying this patch:
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000g > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000gggggggg > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# echo 010000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# echo 0100008 > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# echo 010000aaaaa > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo -n 4096 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]#
[akpm@linux-foundation.org: fix compiler warnings]
[akpm@linux-foundation.org: fix off-by-one found by tiwai@suse.de]
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes simple attributes might need to return an error, e.g. for
acquiring a mutex interruptibly. In fact we have that situation in
spufs already which is the original user of the simple attributes. This
patch merged the temporarily forked attributes in spufs back into the
main ones and allows to return errors.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stefano.brivio@polimi.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The statistics provided here allow the monitoring of allocator behavior but
at the cost of some (minimal) loss of performance. Counters are placed in
SLUB's per cpu data structure. The per cpu structure may be extended by the
statistics to grow larger than one cacheline which will increase the cache
footprint of SLUB.
There is a compile option to enable/disable the inclusion of the runtime
statistics and its off by default.
The slabinfo tool is enhanced to support these statistics via two options:
-D Switches the line of information displayed for a slab from size
mode to activity mode.
-A Sorts the slabs displayed by activity. This allows the display of
the slabs most important to the performance of a certain load.
-r Report option will report detailed statistics on
Example (tbench load):
slabinfo -AD ->Shows the most active slabs
Name Objects Alloc Free %Fast
skbuff_fclone_cache 33 111953835 111953835 99 99
:0000192 2666 5283688 5281047 99 99
:0001024 849 5247230 5246389 83 83
vm_area_struct 1349 119642 118355 91 22
:0004096 15 66753 66751 98 98
:0000064 2067 25297 23383 98 78
dentry 10259 28635 18464 91 45
:0000080 11004 18950 8089 98 98
:0000096 1703 12358 10784 99 98
:0000128 762 10582 9875 94 18
:0000512 184 9807 9647 95 81
:0002048 479 9669 9195 83 65
anon_vma 777 9461 9002 99 71
kmalloc-8 6492 9981 5624 99 97
:0000768 258 7174 6931 58 15
So the skbuff_fclone_cache is of highest importance for the tbench load.
Pretty high load on the 192 sized slab. Look for the aliases
slabinfo -a | grep 000192
:0000192 <- xfs_btree_cur filp kmalloc-192 uid_cache tw_sock_TCP
request_sock_TCPv6 tw_sock_TCPv6 skbuff_head_cache xfs_ili
Likely skbuff_head_cache.
Looking into the statistics of the skbuff_fclone_cache is possible through
slabinfo skbuff_fclone_cache ->-r option implied if cache name is mentioned
.... Usual output ...
Slab Perf Counter Alloc Free %Al %Fr
--------------------------------------------------
Fastpath 111953360 111946981 99 99
Slowpath 1044 7423 0 0
Page Alloc 272 264 0 0
Add partial 25 325 0 0
Remove partial 86 264 0 0
RemoteObj/SlabFrozen 350 4832 0 0
Total 111954404 111954404
Flushes 49 Refill 0
Deactivate Full=325(92%) Empty=0(0%) ToHead=24(6%) ToTail=1(0%)
Looks good because the fastpath is overwhelmingly taken.
skbuff_head_cache:
Slab Perf Counter Alloc Free %Al %Fr
--------------------------------------------------
Fastpath 5297262 5259882 99 99
Slowpath 4477 39586 0 0
Page Alloc 937 824 0 0
Add partial 0 2515 0 0
Remove partial 1691 824 0 0
RemoteObj/SlabFrozen 2621 9684 0 0
Total 5301739 5299468
Deactivate Full=2620(100%) Empty=0(0%) ToHead=0(0%) ToTail=0(0%)
Descriptions of the output:
Total: The total number of allocation and frees that occurred for a
slab
Fastpath: The number of allocations/frees that used the fastpath.
Slowpath: Other allocations
Page Alloc: Number of calls to the page allocator as a result of slowpath
processing
Add Partial: Number of slabs added to the partial list through free or
alloc (occurs during cpuslab flushes)
Remove Partial: Number of slabs removed from the partial list as a result of
allocations retrieving a partial slab or by a free freeing
the last object of a slab.
RemoteObj/Froz: How many times were remotely freed object encountered when a
slab was about to be deactivated. Frozen: How many times was
free able to skip list processing because the slab was in use
as the cpuslab of another processor.
Flushes: Number of times the cpuslab was flushed on request
(kmem_cache_shrink, may result from races in __slab_alloc)
Refill: Number of times we were able to refill the cpuslab from
remotely freed objects for the same slab.
Deactivate: Statistics how slabs were deactivated. Shows how they were
put onto the partial list.
In general fastpath is very good. Slowpath without partial list processing is
also desirable. Any touching of partial list uses node specific locks which
may potentially cause list lock contention.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
- Account for debug_smp_processor_id()'s own preempt_disable() when
displaying the preempt_count().
- 80 cols, not 800.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most pagecache (and some other) radix tree insertions have the great
opportunity to preallocate a few nodes with relaxed gfp flags. But the
preallocation is squandered when it comes time to allocate a node, we
default to first attempting a GFP_ATOMIC allocation -- that doesn't
normally fail, but it can eat into atomic memory reserves that we don't
need to be using.
Another upshot of this is that it removes the sometimes highly contended
zone->lock from underneath tree_lock. Pagecache insertions are always
performed with a radix tree preload, and after this change, such a
situation will never fall back to kmem_cache_alloc within
radix_tree_node_alloc.
David Miller reports seeing this allocation fail on a highly threaded
sparc64 system:
[527319.459981] dd: page allocation failure. order:0, mode:0x20
[527319.460403] Call Trace:
[527319.460568] [00000000004b71e0] __slab_alloc+0x1b0/0x6a8
[527319.460636] [00000000004b7bbc] kmem_cache_alloc+0x4c/0xa8
[527319.460698] [000000000055309c] radix_tree_node_alloc+0x20/0x90
[527319.460763] [0000000000553238] radix_tree_insert+0x12c/0x260
[527319.460830] [0000000000495cd0] add_to_page_cache+0x38/0xb0
[527319.460893] [00000000004e4794] mpage_readpages+0x6c/0x134
[527319.460955] [000000000049c7fc] __do_page_cache_readahead+0x170/0x280
[527319.461028] [000000000049cc88] ondemand_readahead+0x208/0x214
[527319.461094] [0000000000496018] do_generic_mapping_read+0xe8/0x428
[527319.461152] [0000000000497948] generic_file_aio_read+0x108/0x170
[527319.461217] [00000000004badac] do_sync_read+0x88/0xd0
[527319.461292] [00000000004bb5cc] vfs_read+0x78/0x10c
[527319.461361] [00000000004bb920] sys_read+0x34/0x60
[527319.461424] [0000000000406294] linux_sparc_syscall32+0x3c/0x40
The calltrace is significant: __do_page_cache_readahead allocates a number
of pages with GFP_KERNEL, and hence it should have reclaimed sufficient
memory to satisfy GFP_ATOMIC allocations. However after the list of pages
goes to mpage_readpages, there can be significant intervals (including disk
IO) before all the pages are inserted into the radix-tree. So the reserves
can easily be depleted at that point. The patch is confirmed to fix the
problem.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes swiotlb not allocate a memory area spanning LLD's segment
boundary.
is_span_boundary() judges whether a memory area spans LLD's segment boundary.
If map_single finds such a area, map_single tries to find the next available
memory area.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds IOMMU helper functions for the free area management. These
functions take care of LLD's segment boundary limit for IOMMUs. They would be
useful for IOMMUs that use bitmap for the free area management.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
scsi: fix dependency bug in aic7 Makefile
kbuild: add svn revision information to setlocalversion
kbuild: do not warn about __*init/__*exit symbols being exported
Move Kconfig.instrumentation to arch/Kconfig and init/Kconfig
Add HAVE_KPROBES
Add HAVE_OPROFILE
Create arch/Kconfig
Fix ARM to play nicely with generic Instrumentation menu
kconfig: ignore select of unknown symbol
kconfig: mark config as changed when loading an alternate config
kbuild: Spelling/grammar fixes for config DEBUG_SECTION_MISMATCH
Remove __INIT_REFOK and __INITDATA_REFOK
kbuild: print only total number of section mismatces found
Including additional fixes from Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
We have too many section mismatches detected at the moment.
So silence modpost and prevent the option from being
set in a typical allyesconfig build.
Tell the user how to see all the deteils in the summary
message from modpost.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Change latencytop Kconfig entry so it doesn't list the archictectures
that support it. Instead introduce HAVE_LATENCY_SUPPORT which any
architecture can set. Should reduce patch conflicts.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Holger Wolf <wolf@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.
If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.
With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.
In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.
An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.
A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt
It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diff
Signed-Off-By: Bernhard Kaindl <bk@suse.de>
Tested-By: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
During the work on the x86 32 and 64 bit backtrace code I found it useful
to have a simple test module to test a process and irq context backtrace.
Since the existing backtrace code was buggy, I figure it might be useful
to have such a test module in the kernel so that maybe we can even
detect such bugs earlier..
[ mingo@elte.hu: build fix ]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
introduce the "asmregparm" calling convention: for functions
implemented in assembly with a fixed regparm input parameters
calling convention.
mark the semaphore and rwsem slowpath functions with that.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here is a quick and naive smoke test for kprobes. This is intended to
just verify if some unrelated change broke the *probes subsystem. It is
self contained, architecture agnostic and isn't of any great use by itself.
This needs to be built in the kernel and runs a basic set of tests to
verify if kprobes, jprobes and kretprobes run fine on the kernel. In case
of an error, it'll print out a message with a "BUG" prefix.
This is a start; we intend to add more tests to this bucket over time.
Thanks to Jim Keniston and Masami Hiramatsu for comments and suggestions.
Tested on x86 (32/64) and powerpc.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.25: (1470 commits)
[IPV6] ADDRLABEL: Fix double free on label deletion.
[PPP]: Sparse warning fixes.
[IPV4] fib_trie: remove unneeded NULL check
[IPV4] fib_trie: More whitespace cleanup.
[NET_SCHED]: Use nla_policy for attribute validation in ematches
[NET_SCHED]: Use nla_policy for attribute validation in actions
[NET_SCHED]: Use nla_policy for attribute validation in classifiers
[NET_SCHED]: Use nla_policy for attribute validation in packet schedulers
[NET_SCHED]: sch_api: introduce constant for rate table size
[NET_SCHED]: Use typeful attribute parsing helpers
[NET_SCHED]: Use typeful attribute construction helpers
[NET_SCHED]: Use NLA_PUT_STRING for string dumping
[NET_SCHED]: Use nla_nest_start/nla_nest_end
[NET_SCHED]: Propagate nla_parse return value
[NET_SCHED]: act_api: use PTR_ERR in tcf_action_init/tcf_action_get
[NET_SCHED]: act_api: use nlmsg_parse
[NET_SCHED]: act_api: fix netlink API conversion bug
[NET_SCHED]: sch_netem: use nla_parse_nested_compat
[NET_SCHED]: sch_atm: fix format string warning
[NETNS]: Add namespace for ICMP replying code.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (79 commits)
Remove references to "make dep"
kconfig: document use of HAVE_*
Introduce new section reference annotations tags: __ref, __refdata, __refconst
kbuild: warn about ld added unique sections
kbuild: add verbose option to Section mismatch reporting in modpost
kconfig: tristate choices with mixed tristate and boolean values
asm-generic/vmlix.lds.h: simplify __mem{init,exit}* dependencies
remove __attribute_used__
kbuild: support ARCH=x86 in buildtar
kconfig: remove "enable"
kbuild: simplified warning report in modpost
kbuild: introduce a few helpers in modpost
kbuild: use simpler section mismatch warnings in modpost
kbuild: link vmlinux.o before kallsyms passes
kbuild: introduce new option to enhance section mismatch analysis
Use separate sections for __dev/__cpu/__mem code/data
compiler.h: introduce __section()
all archs: consolidate init and exit sections in vmlinux.lds.h
kbuild: check section names consistently in modpost
kbuild: introduce blacklisting in modpost
...
This function is used by the ext4 multi block allocator patches.
Also add generic_find_next_le_bit
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Before pushing pcounter to Linus tree, I would like to make some adjustments.
Goal is to reduce kernel text size, by unlining too big functions.
When a pcounter is bound to a statically defined per_cpu variable,
we define two small helpers functions. (No more folding function
using the fat for_each_possible_cpu(cpu) ... )
static DEFINE_PER_CPU(int, NAME##_pcounter_values);
static void NAME##_pcounter_add(struct pcounter *self, int val)
{
__get_cpu_var(NAME##_pcounter_values) += val;
}
static int NAME##_pcounter_getval(const struct pcounter *self, int cpu)
{
return per_cpu(NAME##_pcounter_values, cpu);
}
Fast path is therefore unchanged, while folding/alloc/free is now unlined.
This saves 228 bytes on i386
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This just generalises what was introduced by Eric Dumazet for the struct proto
inuse field in 286ab3d46058840d68e5d7d52e316c1f7e98c59f:
[NET]: Define infrastructure to keep 'inuse' changes in an efficent SMP/NUMA way.
Please look at the comment in there to see the rationale.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the config option CONFIG_SECTION_MISMATCH is not set and
we see a Section mismatch present the following to the user:
modpost: Found 1 section mismatch(es).
To see additional details select "Enable full Section mismatch analysis"
in the Kernel Hacking menu (CONFIG_SECTION_MISMATCH).
If the option CONFIG_SECTION_MISMATCH is selected
then be verbose in the Section mismatch reporting from mdopost.
Sample outputs:
WARNING: o-x86_64/vmlinux.o(.text+0x7396): Section mismatch in reference from the function discover_ebda() to the variable .init.data:ebda_addr
The function discover_ebda() references
the variable __initdata ebda_addr.
This is often because discover_ebda lacks a __initdata
annotation or the annotation of ebda_addr is wrong.
WARNING: o-x86_64/vmlinux.o(.data+0x74d58): Section mismatch in reference from the variable pci_serial_quirks to the function .devexit.text:pci_plx9050_exit()
The variable pci_serial_quirks references
the function __devexit pci_plx9050_exit()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: o-x86_64/vmlinux.o(__ksymtab+0x630): Section mismatch in reference from the variable __ksymtab_arch_register_cpu to the function .cpuinit.text:arch_register_cpu()
The symbol arch_register_cpu is exported and annotated __cpuinit
Fix this by removing the __cpuinit annotation of arch_register_cpu or drop the export.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Setting the option DEBUG_SECTION_MISMATCH will
report additional section mismatch'es but this
should in the end makes it possible to get rid of
all of them.
See help text in lib/Kconfig.debug for details.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
SCSI sg table allocation has a maximum size (of SCSI_MAX_SG_SEGMENTS,
currently 128) and this will cause a BUG_ON() in SCSI if something
tries an allocation over it. This patch adds a size limit to the
chaining allocator to allow the specification of the maximum
allocation size for chaining, so we always chain in units of the
maximum SCSI allocation size.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Manually doing chained sg lists is not trivial, so add some helpers
to make sure that drivers get it right.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
LatencyTOP kernel infrastructure; it measures latencies in the
scheduler and tracks it system wide and per process.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no in-kernel users of kobject_unregister() so it should be
removed.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We save the current state in the object itself, so we can do proper
cleanup when the last reference is dropped.
If the initial reference is dropped, the object will be removed from
sysfs if needed, if an "add" event was sent, "remove" will be send, and
the allocated resources are released.
This allows us to clean up some driver core usage as well as allowing us
to do other such changes to the rest of the kernel.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No one is calling this anymore, so just remove it and hard-code the one
internal-use of it.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function is no longer used by anyone in the kernel, and it prevents
the proper sending of the kobject uevent after the needed files are set
up by the caller. kobject_init_and_add() can be used in its place.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the old kobject_init() function is gone, rename
kobject_init_ng() to kobject_init() to clean up the namespace.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The old kobject_init() function is on longer in use, so let us remove it
from the public scope (kset mess in the kobject.c file still uses it,
but that can be cleaned up later very simply.)
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the old kobject_add() function is gone, rename kobject_add_ng()
to kobject_add() to clean up the namespace.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The old kobject_add() function is on longer in use, so let us remove it
from the public scope (kset mess in the kobject.c file still uses it,
but that can be cleaned up later very simply.)
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1015) reverts changes that were made to the driver core
about four years ago. The intent back then was to avoid certain kinds
of invalid memory accesses by leaving kernel objects allocated as long
as any of their children were still allocated. The original and
correct approach was to wait only as long as any children were still
_registered_; that's what this patch reinstates.
This fixes a problem in the SCSI core made visible by the class_device
to regular device conversion: A reference loop (scsi_device holds
reference to request_queue, which is the child of a gendisk, which is
the child of the scsi_device) prevents the data structures from being
released, even though they are deregistered okay.
It's possible that this change will cause a few bugs to surface,
things that have been hidden for several years. They can be fixed
easily enough by having the child device take an explicit reference to
the parent whenever needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kobject debugging messages are a mess. This provides a unified
message that makes them actually useful.
The format for new kobject debug messages should be:
kobject: 'KOBJECT_NAME' (ADDRESS): FUNCTION_NAME: message.\n
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_init should not be grabing any references, but only initializing
the object. This patch fixes this, and makes the lock hold-time shorter
for when a kset is present in the kobject.
The current kernel tree has been audited to verify that this change
should be safe.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These functions are no longer used and are the last remants of the old
subsystem crap. So delete them for good.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the no longer needed subsys_attributes, they are all converted to
the more sensical kobj_attributes.
There is no longer a magic fallback in sysfs attribute operations, all
kobjects which create simple attributes need explicitely a ktype
assigned, which tells the core what was intended here.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch all dynamically created ksets, that export simple attributes,
to kobj_attribute from subsys_attribute. Struct subsys_attribute will
be removed.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mike Halcrow <mhalcrow@us.ibm.com>
Cc: Phillip Hellewell <phillip@hellewell.homeip.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add kobj_sysfs_ops to replace subsys_sysfs_ops. There is no
need for special kset operations, we want to be able to use
simple attribute operations at any kobject, not only ksets.
The whole concept of any default sysfs attribute operations
will go away with the upcoming removal of subsys_sysfs_ops.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_kset_add_dir is only called in one place so remove it and use
kobject_create() instead.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_create_and_add is the same as kobject_add_dir, so drop
kobject_add_dir.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now ksets can be dynamically created on the fly, no static definitions
are required. Thanks to Miklos for hints on how to make this work
better for the callers.
And thanks to Kay for finding some stupid bugs in my original version
and pointing out that we need to handle the fact that kobject's can have
a kset as a parent and to handle that properly in kobject_add().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also add a kobject_init_and_add function which bundles up what a lot of
the current callers want to do all at once, and it properly handles the
memory usages, unlike kobject_register();
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is what the kobject_add function is going to become.
Add this to the kernel and then we can convert the tree over to use it.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is what the kobject_init function is going to become.
Add this to the kernel and then we can convert the tree over to use it.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kay pointed out that kobject_set_name was being very stupid, doing two
allocations for every call, when it should just be using the kernel
function kvasprintf() instead.
This change adds the internal kobject_set_name_vargs() function, which
other follow-on patches will be using.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds kref_set() to the kref api for future use by people who really
know what they are doing with krefs...
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Zhe Jiang noticed that its possible to underflow pl->events in
prop_norm_percpu() when the value returned by percpu_counter_read() is less
than the error on that read and the period delay > 1. In that case half might
not trigger the batch increment and the value will be identical on the next
iteration, causing the same half to be subtracted again and again.
Fix this by rewriting the division as a single subtraction instead of a
subtraction loop and using percpu_counter_sum() when the value returned by
percpu_counter_read() is smaller than the error.
The latter is still needed if we want pl->events to shrink properly in the
error region.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This following commit
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=fdf8cb0909b531f9ae8f9b9d7e4eb35ba3505f07
un-inlined a low-level rwsem function, but did not mark it as __sched.
The result is that it now shows up as thread wchan (which also affects
/proc/profile stats). The following simple patch fixes this by properly
marking rwsem_down_failed_common() as a __sched function.
Also in this patch, which is up for discussion, marks down_read() and
down_write() proper as __sched. For profiling, it is pretty much
useless to know that a semaphore is beig help - it is necessary to know
_which_ one. By going up another frame on the stack, the information
becomes much more useful.
In summary, the below change to lib/rwsem.c should be applied; the
changes to kernel/rwsem.c could be applied if other kernel hackers agree
with my proposal that down_read()/down_write() in the profile is not
enough.
[ akpm@linux-foundation.org: build fix ]
Signed-off-by: Livio Soares <livio@eecg.toronto.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thanks to Dave Young <hidave.darkstar@gmail.com> for pointing out that I
forgot to update the comment when I rewrote kobject_set_name.
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
If a zero length pattern is passed then return EINVAL.
Avoids infinite loops (bm) or invalid memory accesses (kmp).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As Herbert Xu pointed out, bytes (chars) with bit 7 (0x80) set are true
with isprint() but they may not be isascii() but be Unicode instead, so
don't try to print them in hex dumps.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes two typos from commit
34358c26a2.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mac80211 has a reference to __bitmap_empty() via bitmap_empty(). In
lib/bitmap.c this is flagged with an EXPORT_SYMBOL(), but this is
ultimately ineffective due to bitmap.o being linked in lib-y, resulting in:
ERROR: "__bitmap_empty" [net/mac80211/mac80211.ko] undefined!
Moving bitmap.o to obj-y fixes this up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
crypto/crc32.c:chksum_final() is computing the digest as
*(__le32 *)out = ~cpu_to_le32(mctx->crc);
so the low-level crc32c_le routines should just keep
the crc in cpu order, otherwise it is getting swabbed
one too many times on big-endian machines.
Signed-off-by: Benny Halevy <bhalevy@fs1.bhalevy.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When a bitmap is empty bitmap_scnlistprintf() would leave the buffer
uninitialized. Set it to an empty string in this case.
I didn't see any in normal kernel callers hitting this, but some custom
debug code of mine did.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should catch any duplicate names before we try to tell sysfs to
rename the object. This happens a lot with older versions of udev and
the network rename scripts.
Cc: David Miller <davem@davemloft.net>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The __deprecated marker is quite useful in highlighting the remnants of
old APIs that want removing.
However, it is quite normal for one or more years to pass, before the
(usually ancient, bitrotten) code in question is either updated or
deleted.
Thus, like __must_check, add a Kconfig option that permits the silencing
of this compiler warning.
This change mimics the ifdef-ery and Kconfig defaults of MUST_CHECK as
closely as possible.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6:
[MTD] [NOR] Fix deadlock in Intel chip driver caused by get_chip recursion
[JFFS2] Fix return value from jffs2_write_end()
[MTD] [OneNAND] Fix wrong free the static address in onenand_sim
[MTD] [NAND] Replace -1 with -EBADMSG in nand error correction code
[RSLIB] BUG() when passing illegal parameters to decode_rs8() or decode_rs16()
[MTD] [NAND] treat any negative return value from correct() as an error
[MTD] [NAND] nandsim: bugfix in initialization
[MTD] Fix typo in Alauda config option help text.
[MTD] [NAND] add s3c2440-specific read_buf/write_buf
[MTD] [OneNAND] onenand-sim: fix kernel-doc and typos
[JFFS2] Tidy up fix for ACL/permissions problem.
Magic numerical values are just bad style. Particularly so when
undocumented.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Replace an irrelevant include of bug.h with the more appropriate
includes of slab.h and module.h.
it's not as if the original inclusion is an error, it's simply not
related to the contents of that source file, while the other two are.
compile-tested on i386.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Begin infrastructure for kernel code samples in the samples/ directory.
Add its Kconfig and Kbuild files.
Source its Kconfig file in all arch/ Kconfigs.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the per-cpu counters and thus their locks are accessed from IRQ
contexts. This can cause a deadlock if it interrupts a cpu-offline thread
which is transferring a dead-cpu's counts to the global counter.
Add appropriate IRQ protection in the cpu-hotplug callback path.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
remove asm/bitops.h includes
including asm/bitops directly may cause compile errors. don't include it
and include linux/bitops instead. next patch will deny including asm header
directly.
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cause writes to cpuset "cpus" file to update cpus_allowed for member tasks:
- collect batches of tasks under tasklist_lock and then call
set_cpus_allowed() on them outside the lock (since this can sleep).
- add a simple generic priority heap type to allow efficient collection
of batches of tasks to be processed without duplicating or missing any
tasks in subsequent batches.
- make "cpus" file update a no-op if the mask hasn't changed
- fix race between update_cpumask() and sched_setaffinity() by making
sched_setaffinity() post-check that it's not running on any cpus outside
cpuset_cpus_allowed().
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Menage <menage@google.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To be consistent with the use of attributes in the rest of the kernel
replace all use of __attribute_pure__ with __pure and delete the definition
of __attribute_pure__.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Negative shifts are not allowed in C (the result is undefined). Same thing
with full-width shifts.
It works on most platforms but not on the VAX with gcc 4.0.1 (it results in an
"operand reserved" fault).
Shifting by more than the width of the value on the left is also not
allowed. I think the extra '>> 1' tacked on at the end in the original
code was an attempt to work around that. Getting rid of that is an extra
feature of this patch.
Here's the chapter and verse, taken from the final draft of the C99
standard ("6.5.7 Bitwise shift operators", paragraph 3):
"The integer promotions are performed on each of the operands. The
type of the result is that of the promoted left operand. If the
value of the right operand is negative or is greater than or equal
to the width of the promoted left operand, the behavior is
undefined."
Thank you to Jan-Benedict Glaw, Christoph Hellwig, Maciej Rozycki, Pekka
Enberg, Andreas Schwab, and Christoph Lameter for review. Special thanks
to Andreas for spotting that my fix only removed half the undefined
behaviour.
Signed-off-by: Peter Lund <firefly@vax64.dk>
Christoph Lameter <clameter@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andreas Schwab <schwab@suse.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: WU Fengguang <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various architectures may call bust_spinlocks() recursively; the function
itself, however, doesn't appear to be meant to be called in this manner.
Nevertheless, this doesn't appear to be a problem as long as
bust_spinlocks(0) doesn't get called twice in a row (otherwise,
unblank_screen() may enter the scheduler). However, at least on i386 die()
has been capable of returning (and on other architectures this should
really be that way, too) when notify_die() returns NOTIFY_STOP.
Short of getting a reply to a respective query, this patch makes
bust_spinlocks() increment/decrement oops_in_progress, and wake klogd only
when the count drops back to zero.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hello, I fixed and tested a small bug in lib/sort.c file, heap sort
function.
The fix avoids unnecessary swap of contents when i is 0 (saves few loads
and stores), which happens every time sort function is called. I felt the
fix is worth bringing it to your attention given the importance and
frequent use of the sort function.
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every file should include the headers containing the prototypes for its global
functions (in this case ioremap_page_range()).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It would be nice if the argv_split library function could gracefully handle
a NULL pointer in the argcp parameter, so as to allow functions using it
that did not care about the value of argc to not have to declare a useless
variable. This patch accomplishes that. Tested by me, with successful
results.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given a set of objects, floating proportions aims to efficiently give the
proportional 'activity' of a single item as compared to the whole set. Where
'activity' is a measure of a temporal property of the items.
It is efficient in that it need not inspect any other items of the set
in order to provide the answer. It is not even needed to know how many
other items there are.
It has one parameter, and that is the period of 'time' over which the
'activity' is measured.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
provide a way to tell lockdep about percpu_counters that are supposed to be
used from irq safe contexts.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_percpu can fail, propagate that error.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide an accurate version of percpu_counter_read.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s/percpu_counter_sum/&_positive/
Because its consitent with percpu_counter_read*
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide a method to set a percpu counter to a specified value.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu_counter is a s64 counter, make _add consitent.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because the current batch setup has an quadric error bound on the counter,
allow for an alternative setup.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s/percpu_counter_mod/percpu_counter_add/
Because its a better name, _mod implies modulo.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sg list elements might not be continuous.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch marks a number of allocations that are either short-lived such as
network buffers or are reclaimable such as inode allocations. When something
like updatedb is called, long-lived and unmovable kernel allocations tend to
be spread throughout the address space which increases fragmentation.
This patch groups these allocations together as much as possible by adding a
new MIGRATE_TYPE. The MIGRATE_RECLAIMABLE type is for allocations that can be
reclaimed on demand, but not moved. i.e. they can be migrated by deleting
them and re-reading the information from elsewhere.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A while back, Nick Piggin introduced a patch to reduce the node memory
usage for small files (commit cfd9b7df4a):
-#define RADIX_TREE_MAP_SHIFT 6
+#define RADIX_TREE_MAP_SHIFT (CONFIG_BASE_SMALL ? 4 : 6)
Unfortunately, he didn't take into account the fact that the
calculation of the maximum path was based on an assumption of having
to round up:
#define RADIX_TREE_MAX_PATH (RADIX_TREE_INDEX_BITS/RADIX_TREE_MAP_SHIFT + 2)
So, if CONFIG_BASE_SMALL is set, you will end up with a
RADIX_TREE_MAX_PATH that is one greater than necessary. The practical
upshot of this is just a bit of wasted memory (one long in the
height_to_maxindex array, an extra pre-allocated radix tree node per
cpu, and extra stack usage in a couple of functions), but it seems
worth getting right.
It's also worth noting that I never build with CONFIG_BASE_SMALL.
What I did to test this was duplicate the code in a small user-space
program and check the results of the calculations for max path and the
contents of the height_to_maxindex array.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than sign direct radix-tree pointers with a special bit, sign the
indirect one that hangs off the root. This means that, given a lookup_slot
operation, the invalid result will be differentiated from the valid
(previously, valid results could have the bit either set or clear).
This does not affect slot lookups which occur under lock -- they can never
return an invalid result. Is needed in future for lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce radix_tree_next_hole(root, index, max_scan) to scan radix tree for
the first hole. It will be used in interleaved readahead.
The implementation is dumb and obviously correct. It can help debug(and
document) the possible smart one in future.
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Optionally add a boot delay after each kernel printk() call, crudely
measured in milliseconds, with a maximum delay of 10 seconds per printk.
Enable CONFIG_BOOT_PRINTK_DELAY=y and then add (e.g.):
"lpj=loops_per_jiffy boot_delay=100"
to the kernel command line.
It has been useful in cases like "during boot, my machine just reboots or the
screen goes black" by slowing down printk, (and adding initcall_debug), we can
usually see the last thing that happened before the lights went out which is
usually a valuable clue.
[akpm@linux-foundation.org: not all architectures implement CONFIG_HZ]
[akpm@linux-foundation.org: fix lots of stuff]
[bunk@stusta.de: kernel/printk.c: make 2 variables static]
[heiko.carstens@de.ibm.com: fix slow down printk on boot compile error]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (37 commits)
PCI: merge almost all of pci_32.h and pci_64.h together
PCI: X86: Introduce and enable PCI domain support
PCI: Add 'nodomains' boot option, and pci_domains_supported global
PCI: modify PCI bridge control ISA flag for clarity
PCI: use _CRS for PCI resource allocation
PCI: avoid P2P prefetch window for expansion ROMs
PCI: skip ISA ioresource alignment on some systems
PCI: remove transparent bridge sizing
pci: write file size to inode on proc bus file write
pci: use size stored in proc_dir_entry for proc bus files
pci: implement "pci=noaer"
PCI: fix IDE legacy mode resources
MSI: Use correct data offset for 32-bit MSI in read_msi_msg()
PCI: Fix incorrect argument order to list_add_tail() in PCI dynamic ID code
PCI: i386: Compaq EVO N800c needs PCI bus renumbering
PCI: Remove no longer correct documentation regarding MSI vector assignment
PCI: re-enable onboard sound on "MSI K8T Neo2-FIR"
PCI: quirk_vt82c586_acpi: Omit reading PCI revision ID
PCI: quirk amd_8131_mmrbc: Omit reading pci revision ID
cpqphp: Use PCI_CLASS_REVISION instead of PCI_REVISION_ID for read
...
On at least ARM (and I'm told MIPS too) dma_free_coherent() has a newish
call context requirement: unlike its dma_alloc_coherent() sibling, it may
not be called with IRQs disabled. (This was new behavior on ARM as of late
2005, caused by ARM SMP updates.) This little surprise can be annoyingly
driver-visible.
Since it looks like that restriction won't be removed, this patch changes
the definition of the API to include that requirement. Also, to help catch
nonportable drivers, it updates the x86 and swiotlb versions to include the
relevant warnings. (I already observed that it trips on the
bus_reset_tasklet of the new firewire_ohci driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Miller <davem@davemloft.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sysfs file poll implementation is scattered over sysfs and kobject.
Event numbering is done in sysfs_dirent but wait itself is done on
kobject. This not only unecessarily bloats both kobject and
sysfs_dirent but is also buggy - if a sysfs_dirent is removed while
there still are pollers, the associaton betwen the kobject and
sysfs_dirent breaks and kobject may be freed with the pollers still
sleeping on it.
This patch moves whole poll implementation into sysfs_open_dirent.
Each time a sysfs_open_dirent is created, event number restarts from 1
and pollers sleep on sysfs_open_dirent. As event sequence number is
meaningless without any open file and pollers should have open file
and thus sysfs_open_dirent, this ephemeral event counting works and is
a saner implementation.
This patch fixes the dnagling sleepers bug and reduces the sizes of
kobject and sysfs_dirent by one pointer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move uevent specific logic from the core into kobject_uevent.c, which
does no longer require to link the unused string array if hotplug
is not compiled in.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While shadow directories appear to be a good idea, the current scheme
of controlling their creation and destruction outside of sysfs appears
to be a locking and maintenance nightmare in the face of sysfs
directories dynamically coming and going. Which can now occur for
directories containing network devices when CONFIG_SYSFS_DEPRECATED is
not set.
This patch removes everything from the initial shadow directory support
that allowed the shadow directory creation to be controlled at a higher
level. So except for a few bits of sysfs_rename_dir everything from
commit b592fcfe7f is now gone.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to historical reasons, struct kobject contained a static array for
the name, and a dynamic pointer in case the name got bigger than the
array. That's just dumb, as people didn't always know which variable to
reference, even with the accessor for the kobject name.
This patch removes the static array, potentially saving a lot of memory
as the majority of kobjects do not have a very long name.
Thanks to Kay for the idea to do this.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more subsystems, it's a kset now so remove the function and
the only two users, which are in the driver core.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more subsystems, it's a kset now so remove the function and
the only two users, which are in the driver core.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel creates a process for every event that is send, even when
there is no binary it could execute. We are needlessly creating around
200-300 failing processes during early bootup, until we have the chance
to disable it from userspace.
This change allows us to disable /sbin/hotplug entirely, if you want to,
by setting UEVENT_HELPER_PATH="" in the kernel config.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move zlib_inflate_blob() out into it's own source file,
infutil.c, so that things like the powerpc zImage builder
in arch/powerpc/boot/Makefile don't end up trying to
compile it.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each netlink socket will live in exactly one network namespace,
this includes the controlling kernel sockets.
This patch updates all of the existing netlink protocols
to only support the initial network namespace. Request
by clients in other namespaces will get -ECONREFUSED.
As they would if the kernel did not have the support for
that netlink protocol compiled in.
As each netlink protocol is updated to be multiple network
namespace safe it can register multiple kernel sockets
to acquire a presence in the rest of the network namespaces.
The implementation in af_netlink is a simple filter implementation
at hash table insertion and hash table look up time.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide some documentation for CONFIG_LOCK_STAT.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add CONFIG_DEBUG_PREEMPT support to ppc64: it was useful for testing
get_paca() preemption. Cheat a little, just use debug_smp_processor_id()
in the debug version of get_paca(): it contains all the right checks and
reporting, though get_paca() doesn't really use smp_processor_id().
Use local_paca for what might have been called __raw_get_paca().
Silence harmless warnings from io.h and lparcfg.c with local_paca -
it is okay for iseries_lparcfg_data to be referencing shared_proc
with preemption enabled: all cpus should show the same value for
shared_proc.
Why do other architectures need TRACE_IRQFLAGS_SUPPORT for DEBUG_PREEMPT?
I don't know, ppc64 appears to get along fine without it.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Run k8t_sound_hostbridge quirk only when needed
PCI: disable MSI on RX790
PCI: disable MSI on RD580
PCI: disable MSI on RS690
PCI: make pcie_get_readrq visible in pci.h
PCI: lets kill the 'PCI hidden behind bridge' message
pci/hotplug/cpqphp_ctrl.c: remove stale BKL use
PCI: Document pci_iomap()
PCI: quirk_e100_interrupt() called too early
PCI: Move prototypes for pci_bus_find_capability to include/linux/pci.h
Introduce CONFIG_CHECK_SIGNATURE to control inclusion of check_signature()
and avoid problems on platforms that don't have readb().
Let the few legacy (ISA || PCI || X86) drivers that need check_signature()
select CONFIG_CHECK_SIGNATURE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial fix: mark the buffer to hexdump as const so callers could avoid
casting their const buffers when calling print_hex_dump().
The patch is really trivial and I suggest to consider it as a fix
(it fixes GCC warnings) and push it to current tree.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kasprintf pulls in kmalloc which proved to be fatal for at least
bootimage target on alpha.
Move it to a separate file so only users of kasprintf are exposed
to the dependency on kmalloc.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jay Estabrook <jay.estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some casts to the LZO compression algorithm after they were removed
during cleanup and shouldn't have been.
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Cc: Edward Shishkin <edward@namesys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leaving kobject_actions[] in kobject_uevent.c, but putting it outside
the #ifdef looks indeed like the best solution to me. This way, we
avoid adding #ifdef CONFIG_HOTPLUG into core.c, when all other
functions called do not need such a thing.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lib/fault-inject.c:168: warning: 'debugfs_create_ul_MAX_STACK_TRACE_DEPTH' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the swiotlb maps a multi-slab region, swiotlb_sync_single_range() can be
invoked to sync a sub-region which does not include the first slab.
Unfortunately io_tlb_orig_addr[] is only initialised for the first slab,
and hence the call to sync_single() will read a garbage orig_addr in this
case.
This patch fixes the issue by initialising all mapped slabs in
io_tlb_orig_addr[]. It also correctly adjusts the buffer pointer in
sync_single() to handle the case that the given dma_addr is not aligned on
a slab boundary.
Signed-off-by: Keir Fraser <keir.fraser@cl.cam.ac.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Introduce the core lock statistics code.
Lock statistics provides lock wait-time and hold-time (as well as the count
of corresponding contention and acquisitions events). Also, the first few
call-sites that encounter contention are tracked.
Lock wait-time is the time spent waiting on the lock. This provides insight
into the locking scheme, that is, a heavily contended lock is indicative of
a too coarse locking scheme.
Lock hold-time is the duration the lock was held, this provides a reference for
the wait-time numbers, so they can be put into perspective.
1)
lock
2)
... do stuff ..
unlock
3)
The time between 1 and 2 is the wait-time. The time between 2 and 3 is the
hold-time.
The lockdep held-lock tracking code is reused, because it already collects locks
into meaningful groups (classes), and because it is an existing infrastructure
for lock instrumentation.
Currently lockdep tracks lock acquisition with two hooks:
lock()
lock_acquire()
_lock()
... code protected by lock ...
unlock()
lock_release()
_unlock()
We need to extend this with two more hooks, in order to measure contention.
lock_contended() - used to measure contention events
lock_acquired() - completion of the contention
These are then placed the following way:
lock()
lock_acquire()
if (!_try_lock())
lock_contended()
_lock()
lock_acquired()
... do locked stuff ...
unlock()
lock_release()
_unlock()
(Note: the try_lock() 'trick' is used to avoid instrumenting all platform
dependent lock primitive implementations.)
It is also possible to toggle the two lockdep features at runtime using:
/proc/sys/kernel/prove_locking
/proc/sys/kernel/lock_stat
(esp. turning off the O(n^2) prove_locking functionaliy can help)
[akpm@linux-foundation.org: build fixes]
[akpm@linux-foundation.org: nuke unneeded ifdefs]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows the uevent file to handle any type of uevent action to be
triggered by userspace instead of just the "add" uevent.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than using a tri-state integer for the wait flag in
call_usermodehelper_exec, define a proper enum, and use that. I've
preserved the integer values so that any callers I've missed should
still work OK.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: David Howells <dhowells@redhat.com>
argv_split() is a helper function which takes a string, splits it at
whitespace, and returns a NULL-terminated argv vector. This is
deliberately simple - it does no quote processing of any kind.
[ Seems to me that this is something which is already being done in
the kernel, but I couldn't find any other implementations, either to
steal or replace. Keep an eye out. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Add CRC7 routines, used for example in MMC over SPI communication.
Kerneldoc updates
[akpm@linux-foundation.org: fix funny mix of const and non-const]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmalloc_node() and kmem_cache_alloc_node() were not available in a zeroing
variant in the past. But with __GFP_ZERO it is possible now to do zeroing
while allocating.
Use __GFP_ZERO to remove the explicit clearing of memory via memset whereever
we can.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should avoid build problems on architectures without a "readb()",
that got bitten by check_signature() being uninlined.
Noted by Heiko Carstens.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Optimize integer-to-string conversion in vsprintf.c for base 10. This is
by far the most used conversion, and in some use cases it impacts
performance. For example, top reads /proc/$PID/stat for every process, and
with 4000 processes decimal conversion alone takes noticeable time.
Using code from
http://www.cs.uiowa.edu/~jones/bcd/decimal.html
(with permission from the author, Douglas W. Jones)
binary-to-decimal-string conversion is done in groups of five digits at
once, using only additions/subtractions/shifts (with -O2; -Os throws in
some multiply instructions).
On i386 arch gcc 4.1.2 -O2 generates ~500 bytes of code.
This patch is run tested. Userspace benchmark/test is also attached.
I tested it on PIII and AMD64 and new code is generally ~2.5 times
faster. On AMD64:
# ./vsprintf_verify-O2
Original decimal conv: .......... 151 ns per iteration
Patched decimal conv: .......... 62 ns per iteration
Testing correctness
12895992590592 ok... [Ctrl-C]
# ./vsprintf_verify-O2
Original decimal conv: .......... 151 ns per iteration
Patched decimal conv: .......... 62 ns per iteration
Testing correctness
26025406464 ok... [Ctrl-C]
More realistic test: top from busybox project was modified to
report how many us it took to scan /proc (this does not account
any processing done after that, like sorting process list),
and then I test it with 4000 processes:
#!/bin/sh
i=4000
while test $i != 0; do
sleep 30 &
let i--
done
busybox top -b -n3 >/dev/null
on unpatched kernel:
top: 4120 processes took 102864 microseconds to scan
top: 4120 processes took 91757 microseconds to scan
top: 4120 processes took 92517 microseconds to scan
top: 4120 processes took 92581 microseconds to scan
on patched kernel:
top: 4120 processes took 75460 microseconds to scan
top: 4120 processes took 66451 microseconds to scan
top: 4120 processes took 67267 microseconds to scan
top: 4120 processes took 67618 microseconds to scan
The speedup comes from much faster generation of /proc/PID/stat
by sprintf() calls inside the kernel.
Signed-off-by: Douglas W Jones <jones@cs.uiowa.edu>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* There is no point in having full "0...9a...z" constant vector,
if we use only "0...9a...f" (and "x" for "0x").
* Post-decrement usually needs a few more instructions, so use
pre decrement instead where makes sense:
- while (i < precision--) {
+ while (i <= --precision) {
* if base != 10 (=> base 8 or 16), we can avoid using division
in a loop and use mask/shift, obtaining much faster conversion.
(More complex optimization for base 10 case is in the second patch).
Overall, size vsprintf.o shows ~80 bytes smaller text section
with this patch applied.
Signed-off-by: Douglas W Jones <jones@cs.uiowa.edu>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current generic bug implementation has a call to dump_stack() in case a
WARN_ON(whatever) gets hit. Since report_bug(), which calls dump_stack(),
gets called from an exception handler we can do better: just pass the
pt_regs structure to report_bug() and pass it to show_regs() in case of a
warning. This will give more debug informations like register contents,
etc... In addition this avoids some pointless lines that dump_stack()
emits, since it includes a stack backtrace of the exception handler which
is of no interest in case of a warning. E.g. on s390 the following lines
are currently always present in a stack backtrace if dump_stack() gets
called from report_bug():
[<000000000001517a>] show_trace+0x92/0xe8)
[<0000000000015270>] show_stack+0xa0/0xd0
[<00000000000152ce>] dump_stack+0x2e/0x3c
[<0000000000195450>] report_bug+0x98/0xf8
[<0000000000016cc8>] illegal_op+0x1fc/0x21c
[<00000000000227d6>] sysc_return+0x0/0x10
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a rather bizarre thing to have inlined in io.h. Stick it in lib/
instead.
While we're there, despaghetti it a bit, and fix its off-by-one behaviour when
passed a zero length.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have implemented hotunplug-time counter spilling,
percpu_counter_sum() only needs to look at online CPUs.
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
per-cpu counters presently must iterate over all possible CPUs in the
exhaustive percpu_counter_sum().
But it can be much better to only iterate over the presently-online CPUs. To
do this, we must arrange for an offlined CPU's count to be spilled into the
counter's central count.
We can do this for all percpu_counters in the machine by linking them into a
single global list and walking that list at CPU_DEAD time.
(I hope. Might have race windows in which the percpu_counter_sum() count is
inaccurate?)
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new configuration variable
CONFIG_SLUB_DEBUG_ON
If set then the kernel will be booted by default with slab debugging
switched on. Similar to CONFIG_SLAB_DEBUG. By default slab debugging
is available but must be enabled by specifying "slub_debug" as a
kernel parameter.
Also add support to switch off slab debugging for a kernel that was
built with CONFIG_SLUB_DEBUG_ON. This works by specifying
slub_debug=-
as a kernel parameter.
Dave Jones wanted this feature.
http://marc.info/?l=linux-kernel&m=118072189913045&w=2
[akpm@linux-foundation.org: clean up switch statement]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove all ids from the given idr tree. idr_destroy() only frees up
unused, cached idp_layers, but this function will remove all id mappings
and leave all idp_layers unused.
A typical clean-up sequence for objects stored in an idr tree, will use
idr_for_each() to free all objects, if necessay, then idr_remove_all() to
remove all ids, and idr_destroy() to free up the cached idr_layers.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an iterator function for the idr data structure. Compared
to just iterating through the idr with an integer and idr_find, this
iterator is (almost, but not quite) linear in the number of elements, as
opposed to the number of integers in the range covered by the idr. This
makes a difference for sparse idrs, but more importantly, it's a nicer way
to iterate through the elements.
The drm subsystem is moving to idr for tracking contexts and drawables, and
with this change, we can use the idr exclusively for tracking these
resources.
[akpm@linux-foundation.org: fix comment]
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (37 commits)
[XFS] Fix lockdep annotations for xfs_lock_inodes
[LIB]: export radix_tree_preload()
[XFS] Fix XFS_IOC_FSBULKSTAT{,_SINGLE} & XFS_IOC_FSINUMBERS in compat mode
[XFS] Compat ioctl handler for handle operations
[XFS] Compat ioctl handler for XFS_IOC_FSGEOMETRY_V1.
[XFS] Clean up function name handling in tracing code
[XFS] Quota inode has no parent.
[XFS] Concurrent Multi-File Data Streams
[XFS] Use uninitialized_var macro to stop warning about rtx
[XFS] XFS should not be looking at filp reference counts
[XFS] Use is_power_of_2 instead of open coding checks
[XFS] Reduce shouting by removing unnecessary macros from dir2 code.
[XFS] Simplify XFS min/max macros.
[XFS] Kill off xfs_count_bits
[XFS] Cancel transactions on xfs_itruncate_start error.
[XFS] Use do_div() on 64 bit types.
[XFS] Fix remount,readonly path to flush everything correctly.
[XFS] Cleanup inode extent size hint extraction
[XFS] Prevent ENOSPC from aborting transactions that need to succeed
[XFS] Prevent deadlock when flushing inodes on unmount
...
XFS filestreams functionality uses radix trees and the preload
functions. XFS can be built as a module and hence we need
radix_tree_preload() exported. radix_tree_preload_end() is a
static inline, so it doesn't need exporting.
Signed-Off-By: Dave Chinner <dgc@sgi.com>
Signed-Off-By: Tim Shimmin <tes@sgi.com>
As kobj sysfs dentries and inodes are gonna be made reclaimable,
dentry can't be used as naming token for sysfs file/directory, replace
kobj->dentry with kobj->sd. The only external interface change is
shadow directory handling. All other changes are contained in kobj
and sysfs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement idr based id allocator. ida is used the same way idr is
used but lacks id -> ptr translation and thus consumes much less
memory. struct ida_bitmap is attached as leaf nodes to idr tree which
is managed by the idr code. Each ida_bitmap is 128bytes long and
contains slightly less than a thousand slots.
ida is more aggressive with releasing extra resources acquired using
ida_pre_get(). After every successful id allocation, ida frees one
reserved idr_layer if possible. Reserved ida_bitmap is not freed
automatically but only one ida_bitmap is reserved and it's almost
always used right away. Under most circumstances, ida won't hold on
to memory for too long which isn't actively used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Separate out idr_mark_full() from sub_alloc() and make marking the
allocated slot full the responsibility of idr_get_new_above_int().
Allocation part of idr_get_new_above_int() is renamed to
idr_get_empty_slot(). New idr_get_new_above_int() allocates a slot
using the function, install the user pointer and marks it full using
idr_mark_full().
This change doesn't introduce any behavior change. This will be
used by ida.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In sub_alloc(), when bitmap search fails, it goes up one level to
continue search. This is done by updating the id cursor and searching
the upper level again. If the cursor was at the end of the upper
level, we need to go further than that.
This wasn't implemented and when that happens the part of the cursor
which indexes into the upper level wraps and sub_alloc() ends up
searching the wrong bitmap. It allocates id which doesn't match the
actual slot.
This patch fixes this by restarting from the top if the search needs
to go higher than one level.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We get uevents for a bus/class going away, but not one registering.
Add the missing uevent in kset_register(), which will send an
event for a new bus/class. Suppress all unwanted uevents for bus
subdirectories like /bus/*/devices/, /bus/*/drivers/.
Now we get for module usbcore:
add /module/usbcore (module)
add /bus/usb (bus)
add /class/usb_host (class)
add /bus/usb/drivers/hub (drivers)
add /bus/usb/drivers/usb (drivers)
remove /bus/usb/drivers/usb (drivers)
remove /bus/usb/drivers/hub (drivers)
remove /class/usb_host (class)
remove /bus/usb (bus)
remove /module/usbcore (module)
instead of:
add /module/usbcore (module)
add /bus/usb/drivers/hub (drivers)
add /bus/usb/drivers/usb (drivers)
remove /bus/usb/drivers/usb (drivers)
remove /bus/usb/drivers/hub (drivers)
remove /class/usb_host (class)
remove /bus/usb/drivers (bus)
remove /bus/usb/devices (bus)
remove /bus/usb (bus)
remove /module/usbcore (module)
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a hybrid version of the patch to add the LZO1X compression
algorithm to the kernel. Nitin and myself have merged the best parts of
the various patches to form this version which we're both happy with (and
are jointly signing off).
The performance of this version is equivalent to the original minilzo code
it was based on. Bytecode comparisons have also been made on ARM, i386 and
x86_64 with favourable results.
There are several users of LZO lined up including jffs2, crypto and reiser4
since its much faster than zlib.
Signed-off-by: Nitin Gupta <nitingupta910@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a prefix string parameter. Callers are responsible for any string
length/alignment that they want to see in the output. I.e., callers should
pad strings to achieve alignment if they want that.
Add rowsize parameter. This is the number of raw data bytes to be printed
per line. Must be 16 or 32.
Add a groupsize parameter. This allows callers to dump values as 1-byte,
2-byte, 4-byte, or 8-byte numbers. Default is 1-byte numbers. If the
total length is not an even multiple of groupsize, 1-byte numbers are
printed.
Add an "ascii" output parameter. This causes ASCII data output following
the hex data output.
Clean up some doc examples.
Align the ASCII output on all lines that are produced by one call.
Add a new interface, print_hex_dump_bytes(), that is a shortcut to
print_hex_dump(), using default parameter values to print 16 bytes in
byte-size chunks of hex + ASCII output, using printk level KERN_DEBUG.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to Jean Delvare <khali@linux-fr.org> for pointing it out to me.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make timer-stats have almost zero overhead when enabled in the config but
not used. (this way distros can enable it more easily)
Also update the documentation about overhead of timer_stats - it was
written for the first version which had a global lock and a linear list
walk based lookup ;-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There have been a number of instances where people have accidentally compiled
rcutorture into the kernel (CONFIG_RCU_TORTURE_TEST=y), which has never been
useful, and has often resulted in great frustration.
The attached patch prohibits rcutorture from being compiled into the
kernel. It may be excluded altogether or compiled as a module. People
wishing to have rcutorture hammer their machine immediately upon boot
are free to hand-edit lib/Kconfig.debug to remove the "depends on m"
line.
Thanks to Randy Dunlap for the trick that makes this work.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Josh Triplett <josh@kernel.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable stacktrace filter support for x86-64 for now. Will be enable when we
can get the dwarf2 unwinder back.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'audit.b38' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] Abnormal End of Processes
[PATCH] match audit name data
[PATCH] complete message queue auditing
[PATCH] audit inode for all xattr syscalls
[PATCH] initialize name osid
[PATCH] audit signal recipients
[PATCH] add SIGNAL syscall class (v3)
[PATCH] auditing ptrace
Based on ace_dump_mem() from Grant Likely for the Xilinx SystemACE
CompactFlash interface.
Add print_hex_dump() & hex_dumper() to lib/hexdump.c and linux/kernel.h.
This patch adds the functions print_hex_dump() & hex_dumper().
print_hex_dump() can be used to perform a hex + ASCII dump of data to
syslog, in an easily viewable format, thus providing a common text hex dump
format.
hex_dumper() provides a dump-to-memory function. It converts one "line" of
output (16 bytes of input) at a time.
Example usages:
print_hex_dump(KERN_DEBUG, DUMP_PREFIX_ADDRESS, frame->data, frame->len);
hex_dumper(frame->data, frame->len, linebuf, sizeof(linebuf));
Example output using %DUMP_PREFIX_OFFSET:
0009ab42: 40414243 44454647 48494a4b 4c4d4e4f-@ABCDEFG HIJKLMNO
Example output using %DUMP_PREFIX_ADDRESS:
ffffffff88089af0: 70717273 74757677 78797a7b 7c7d7e7f-pqrstuvw xyz{|}~.
[akpm@linux-foundation.org: cleanups, add export]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When auditing syscalls that send signals, log the pid and security
context for each target process. Optimize the data collection by
adding a counter for signal-related rules, and avoiding allocating an
aux struct unless we have more than one target process. For process
groups, collect pid/context data in blocks of 16. Move the
audit_signal_info() hook up in check_kill_permission() so we audit
attempts where permission is denied.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'juju' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (138 commits)
firewire: Convert OHCI driver to use standard goto unwinding for error handling.
firewire: Always use parens with sizeof.
firewire: Drop single buffer request support.
firewire: Add a comment to describe why we split the sg list.
firewire: Return SCSI_MLQUEUE_HOST_BUSY for out of memory cases in queuecommand.
firewire: Handle the last few DMA mapping error cases.
firewire: Allocate scsi_host up front and allocate the sbp2_device as hostdata.
firewire: Provide module aliase for backwards compatibility.
firewire: Add to fw-core-y instead of assigning fw-core-objs in Makefile.
firewire: Break out shared IEEE1394 constant to separate header file.
firewire: Use linux/*.h instead of asm/*.h header files.
firewire: Uppercase most macro names.
firewire: Coding style cleanup: no spaces after function names.
firewire: Convert card_rwsem to a regular mutex.
firewire: Clean up comment style.
firewire: Use lib/ implementation of CRC ITU-T.
CRC ITU-T V.41
firewire: Rename fw-device-cdev.c to fw-cdev.c and move header to include/linux.
firewire: Future proof the iso ioctls by adding a handle for the iso context.
firewire: Add read/write and size annotations to IOC numbers.
...
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will add the CRC calculation according
to the CRC ITU-T V.41 to the kernel lib/ folder.
This code has been derived from the rt2x00 driver,
currently found only in the wireless-dev tree, but
this library is generic and could be used by more
drivers who currently use their own implementation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Also useful for the new firewire stack.
Signed-off-by: Kristian Hoegsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.infradead.org/mtd-2.6: (21 commits)
[MTD] [CHIPS] Remove MTD_OBSOLETE_CHIPS (jedec, amd_flash, sharp)
[MTD] Delete allegedly obsolete "bank_size" field of mtd_info.
[MTD] Remove unnecessary user space check from mtd.h.
[MTD] [MAPS] Remove flash maps for no longer supported 405LP boards
[MTD] [MAPS] Fix missing printk() parameter in physmap_of.c MTD driver
[MTD] [NAND] platform NAND driver: add driver
[MTD] [NAND] platform NAND driver: update header
[JFFS2] Simplify and clean up jffs2_add_tn_to_tree() some more.
[JFFS2] Remove another bogus optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remove broken insert_point optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remember to calculate overlap on nodes which replace older nodes
[JFFS2] Don't advance c->wbuf_ofs to next eraseblock after wbuf flush
[MTD] [NAND] at91_nand.c: CMDLINE_PARTS support
[MTD] [NAND] Tidy up handling of page number in nand_block_bad()
[MTD] block2mtd_paramline[] mustn't be __initdata
[MTD] [NAND] Support multiple chips in CAFÉ driver
[MTD] [NAND] Rename cafe.c to cafe_nand.c and remove the multi-obj magic
[MTD] [NAND] Use rslib for CAFÉ ECC
[RSLIB] Support non-canonical GF representations
[JFFS2] Remove dead file histo_mips.h
...
Since nonboot CPUs are now disabled after tasks and devices have been
frozen and the CPU hotplug infrastructure is used for this purpose, we need
special CPU hotplug notifications that will help the CPU-hotplug-aware
subsystems distinguish normal CPU hotplug events from CPU hotplug events
related to a system-wide suspend or resume operation in progress. This
patch introduces such notifications and causes them to be used during
suspend and resume transitions. It also changes all of the
CPU-hotplug-aware subsystems to take these notifications into consideration
(for now they are handled in the same way as the corresponding "normal"
ones).
[oleg@tv-sign.ru: cleanups]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several people have observed that perhaps LOG_BUF_SHIFT should be in a more
obvious place than under DEBUG_KERNEL. Under some circumstances (such as the
PARISC architecture), DEBUG_KERNEL can increase kernel size, which is an
undesirable trade off for something as trivial as increasing the kernel log
buffer size.
Instead, move LOG_BUF_SHIFT into "General Setup", so that people are more
likely to be able to change it such a circumstance that the default buffer
size is insufficient.
Signed-off-by: Alistair John Strachan <s0348365@sms.ed.ac.uk>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I was playing with some code that sometimes got a string where a %n
match should have been done where the input string ended, for example
like this:
sscanf("abc123", "abc%d%n", &a, &n); /* doesn't work */
sscanf("abc123a", "abc%d%n", &a, &n); /* works */
However, the scanf function in the kernel doesn't convert the %n in that
case because it has already matched the complete input after %d and just
completely stops matching then. This patch fixes that.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the Kconfig selection of semaphore debugging from the ALPHA and FRV
Kconfig files, and centralize it in lib/Kconfig.debug.
There doesn't seem to be much point in letting individual architectures
independently define the same Kconfig option when it can just as easily be
put in a single Kconfig file and made dependent on a subset of
architectures. that way, at least the option shows up in the same relative
location in the menu each time.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kbuild spits outs following warning on a
defconfig x86_64 build:
WARNING: swiotlb.o - Section mismatch: reference to .init.text:swiotlb_init from __ksymtab between '__ksymtab_swiotlb_init' (at offset 0xa0) and '__ksymtab_swiotlb_free_coherent'
This warning happens because the function swiotlb_init is marked __init and
EXPORT_SYMBOL(). A 'git grep swiotlb_init' showed no users in drivers/ so
remove the EXPORT_SYMBOL.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last zlib_inflate update broke certain corner cases for ppp_deflate
decompression handling. This patch fixes some logic to make things work
properly again. Users other than ppp_deflate (the only Z_PACKET_FLUSH
user) should be unaffected.
Fixes bug 8405 (confirmed by Stefan)
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Stefan Wenk <stefan.wenk@gmx.at>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the Analog Devices Blackfin processor architecture, and
currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561
(Dual Core) devices, with a variety of development platforms including those
avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP,
BF561-EZKIT), and Bluetechnix! Tinyboards.
The Blackfin architecture was jointly developed by Intel and Analog Devices
Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in
December of 2000. Since then ADI has put this core into its Blackfin
processor family of devices. The Blackfin core has the advantages of a clean,
orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC
(Multiply/Accumulate), state-of-the-art signal processing engine and
single-instruction, multiple-data (SIMD) multimedia capabilities into a single
instruction-set architecture.
The Blackfin architecture, including the instruction set, is described by the
ADSP-BF53x/BF56x Blackfin Processor Programming Reference
http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf
The Blackfin processor is already supported by major releases of gcc, and
there are binary and source rpms/tarballs for many architectures at:
http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete
documentation, including "getting started" guides available at:
http://docs.blackfin.uclinux.org/ which provides links to the sources and
patches you will need in order to set up a cross-compiling environment for
bfin-linux-uclibc
This patch, as well as the other patches (toolchain, distribution,
uClibc) are actively supported by Analog Devices Inc, at:
http://blackfin.uclinux.org/
We have tested this on LTP, and our test plan (including pass/fails) can
be found at:
http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel
[m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files]
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Aubrey Li <aubrey.li@analog.com>
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures that don't support DMA can say so by adding a config NO_DMA
to their Kconfig file. This will prevent compilation of some dma specific
driver code. Also dma-mapping-broken.h isn't needed anymore on at least
s390. This avoids compilation and linking of otherwise dead/broken code.
Other architectures that include dma-mapping-broken.h are arm26, h8300,
m68k, m68knommu and v850. If these could be converted as well we could get
rid of the header file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
"John W. Linville" <linville@tuxdriver.com>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: <James.Bottomley@SteelEye.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: <geert@linux-m68k.org>
Cc: <zippel@linux-m68k.org>
Cc: <spyro@f2s.com>
Cc: <uclinux-v850@lsi.nec.co.jp>
Cc: <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The nr_cpu_ids value is currently only calculated in smp_init. However, it
may be needed before (SLUB needs it on kmem_cache_init!) and other kernel
components may also want to allocate dynamically sized per cpu array before
smp_init. So move the determination of possible cpus into sched_init()
where we already loop over all possible cpus early in boot.
Also initialize both nr_node_ids and nr_cpu_ids with the highest value they
could take. If we have accidental users before these values are determined
then the current valud of 0 may cause too small per cpu and per node arrays
to be allocated. If it is set to the maximum possible then we only waste
some memory for early boot users.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We used to BUG_ON() for a badly mapped IO port, which is certainly
correct, but actually made it harder to debug the case where the ATA
drivers had incorrectly mapped a nonconnected ATA port.
So make badly mapped ports trigger a WARN_ON(), and throw the IO away
instead (and return all ones for reads). For things like broken driver
initialization - which is the most likely cause anyway - that should
mean that the machine comes up and is usable (at least that was the case
for the ATA breakage that triggered this patch).
It tends to be a whole lot easier to do a "dmesg" on a working machine
than to try to capture logs off a dead one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox
Linus Torvalds
Stefan Richter
David S. Miller
Jason Wessel
Paul Mackerras
Christoph Lameter
Harvey Harrison
FUJITA Tomonori
Andi Kleen
Denis V. Lunev
Mark Lord
Pavel Emelyanov
Tejun Heo
Jan Beulich
Linus Torvalds
Greg Kroah-Hartman
Hoang-Nam Nguyen
Chris Snook
Kumar Gala
Sam Ravnborg
Becky Bruce
Denys Vlasenko
Guennadi Liakhovetski
Yi Yang
Christoph Hellwig
David Howells
Andrew Morton
Eric Dumazet
Nick Piggin
FUJITA Tomonori
Joe Perches
Geert Uytterhoeven
Dave Young
Heiko Carstens
Bernhard Kaindl
Arjan van de Ven
Ingo Molnar
Ananth N Mavinakayanahalli
Aneesh Kumar K.V
Arnaldo Carvalho de Melo
James Bottomley
Jens Axboe
Arjan van de Ven
Kay Sievers
Alan Stern
Evgeniy Polyakov
Peter Zijlstra
Livio Soares
Pablo Neira Ayuso
Randy Dunlap
Johannes Berg
Mike Frysinger
Paul Mundt
Benny Halevy
Jeff Garzik
Jörn Engel
Simon Arlott
Robert P. J. Day
Mathieu Desnoyers
Gautham R Shenoy
Jiri Slaby
Paul Menage
Ralf Baechle
Rene Herman
Peter Lund
Subbaiah Venkata
Adrian Bunk
Neil Horman
Mel Gorman
Jeff Moyer
Fengguang Wu
Randy Dunlap
Al Viro
David Brownell
Eric W. Biederman
David S. Miller
Alexey Dobriyan
Hugh Dickins
Danny ter Haar
Geert Uytterhoeven
Rolf Eike Beer
Artem Bityutskiy
Oleg Nesterov
Richard Purdie
Cornelia Huck
Stephen Rothwell
Keir Fraser
Jeremy Fitzhardinge
Jan Nikitenko
Kristian Hoegsberg
David Chinner
Richard Purdie
Paul E. McKenney
Alexey Dobriyan
Akinobu Mita
Amy Griffis
Ivo van Doorn
Rafael J. Wysocki
Alistair John Strachan
Richard Purdie
Bryan Wu
Christoph Lameter