Pull libata updates from Tejun Heo:
"Mostly low level driver specific changes.
Two changes are somewhat noteworthy. First, Dan's patchset to support
per-port msix interrupt handling for ahci, which was tried last cycle
but had to be backed out due to a couple issues, is back and seems to
be working fine. Second, libata exception handling now uses
usleep_range() instead of msleep() for sleeps < 20ms which can make
things snappier in some corner cases"
* 'for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: skip debounce delay on link resume
ata: ahci_brcmstb: disable DIPM support
ata: ahci_brcmstb: enable support for ALPM
drivers: libata-core: Use usleep_range() instead of msleep() for short sleeps (<20 ms)
sata_sx4: correctly handling failed allocation
ata: ahci_brcmstb: add support for MIPS-based platforms
ahci: qoriq: Adjust the default register values on ls1021a
ahci: qoriq: Update the default Rx watermark value
ahci: qoriq: Adjust the default register values on ls1043a
ahci: compile out msi/msix infrastructure
ata: core: fix irq description on AHCI single irq systems
ata: ahci_brcmstb: remove unused definitions
ata: ahci_brcmstb: add a quirk for MIPS-based platforms
ata: ahci_brcmstb: disable NCQ for MIPS-based platforms
ata: sata_rcar: Remove obsolete platform_device_id entries
sata_rcar: Add compatible string for r8a7795
ahci: kill 'intr_status'
ahci: switch from 'threaded' to 'hardirq' interrupt handling
ahci: per-port msix support
Quoting Arnd:
The AHCI driver is used for some on-chip devices that do not use PCI
for probing, and it can be built even when CONFIG_PCI is disabled, but
that now results in a build failure:
ata/libahci.c: In function 'ahci_host_activate_multi_irqs':
ata/libahci.c:2475:4: error: invalid use of undefined type 'struct msix_entry'
ata/libahci.c:2475:21: error: dereferencing pointer to incomplete type 'struct msix_entry'
Add ifdef CONFIG_PCI_MSI infrastructure to compile out the multi-msi and
multi-msix code.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested--by: Arnd Bergmann <arnd@arndb.de>
[arnd: fix up pci enabled case]
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes: d684a90d38 ("ahci: per-port msix support")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Current code doesn't update port value of Port Multiplier(PM) when
sending FIS of softreset to device, command will fail if FBS is
enabled.
There are two ways to fix the issue: the first is to disable FBS
before sending softreset command to PM device and the second is
to update port value of PM when sending command.
For the first way, i can't find any related rule in AHCI Spec. The
second way can avoid disabling FBS and has better performance.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
For high frequency I/O the overhead of threaded interrupts impacts
performance. A quick out-of-the-box test (i.e. no affinity tuning)
shows ~10% random read performance at ~20% less cpu. The cpu wins
appear to be from reduced lock contention.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some AHCI controllers support per-port MSI-X vectors. At the same time
the Linux AHCI driver needs to support one-off architectures that
implement a single MSI-X vector for all ports. The heuristic for
enabling AHCI ports becomes, in order of preference:
1/ per-port multi-MSI-X
2/ per-port multi-MSI
3/ single MSI
4/ single MSI-X
5/ legacy INTX
This all depends on AHCI implementations with potentially broken MSI-X
requesting less vectors than the number of ports. If this assumption is
violated we will need to start explicitly white-listing AHCI-MSIX
implementations.
Reported-by: Ricardo Neri <ricardo.neri@intel.com>
[ricardo: fix struct msix_entry handling]
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
With devm there is no need to explicitly free irqs on error.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
MSI messages are per-device, so there will never be another "shared"
device in the interrupt chain.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the AHCI ports' HPCP or ESP bits are set, the port
should be considered external (e.g. eSATA) and is marked
as removable. Userspace tools like udisks then treat it
like an usb drive.
With this patch applied, when I plug a drive into the esata port,
KDE pops up a window asking what to do with the drives(s), just
like it does for any random USB stick.
Removability is indicated to the upper layers by way of the
SCSI RMB bit, as I haven't found another way to signal
userspace to treat a sata disk like any usb stick.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- a number of libata core changes to better support NCQ TRIM.
- ahci now supports MSI-X in single IRQ mode to support a new
controller which doesn't implement MSI or INTX.
- ahci now supports edge-triggered IRQ mode to support a new controller
which for some odd reason did edge-triggered IRQ.
- the usual controller support additions and changes.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
libata: Do not blacklist Micron M500DC
ata: ahci_mvebu: add suspend/resume support
ahci, msix: Fix build error for !PCI_MSI
ahci: Add support for Cavium's ThunderX host controller
ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
libata: finally use __initconst in ata_parse_force_one()
drivers: ata: add support for Ceva sata host controller
devicetree:bindings: add devicetree bindings for ceva ahci
ahci: added support for Freescale AHCI sata
ahci: Store irq number in struct ahci_host_priv
ahci: Move interrupt enablement code to a separate function
Doc: libata: Fix spelling typo found in libata.xml
ata:sata_nv - Change 1 to true for bool type variable.
ata: add Broadcom AHCI SATA3 driver for STB chips
Documentation: devicetree: add Broadcom SATA binding
libata: Fix regression when the NCQ Send and Receive log page is absent
ata: hpt366: fix constant cast warning
ata: ahci_xgene: potential NULL dereference in probe
ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
...
Currently, ahci supports only msi and intx. To also support msix the
handling of the irq number need to be changed. The irq number for msix
devices is taken from msi_list instead of pci_dev. Thus, the irq
number of a device needs to be stored in struct ahci_host_priv now.
This allows the host controller to be activated in a generic way.
This change is only intended for ahci drivers. For that reason the irq
number is stored in struct ahci_host_priv used only by ahci drivers.
Thus, the ABI changes only for ahci_host_activate(), but existing ata
drivers (about 50) are unaffected and keep unchanged. All users of
ahci_host_activate() have been updated.
While touching drivers/ata/libahci.c, doing a small code cleanup in
ahci_port_start().
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the support to handle HOST_IRQ_STAT as edge trigger
latch.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch refactors the ahci_single_irq_intr function and also rename
it to ahci_single_level_irq_intr as it handles a level triggered latch.
Signed-off-by: Suman tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is a preparation commit that will allow to add other criteria
according to which PHY events should be dropped.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
According to the Serial ATA AHCI specification, Device Sleep is an
optional feature and as such no errors should be printed if it's
missing. Keep informing users, but use dev_info() instead of dev_err().
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 33fb0d01ce.
18dcf433f3 ("AHCI: Optimize single IRQ interrupt processing") is
scheduled to be reverted. This is an optimization dependent on the
mentioned commit. Revert it first.
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no need to acquire ata_host::lock spinlock from
hardware context single IRQ interrupt handler since the
handler does not access host data that could be altered
by concurrent processors.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Split interrupt service routine into hardware context handler
and threaded context handler. That allows to protect ports with
individual locks rather than with a single host-wide lock and
move port interrupts handling out of the hardware interrupt
context.
Testing was done by transferring 8GB on two hard drives in
parallel using command 'dd if=/dev/sd{a,b} of=/dev/null'. With
lock_stat statistics I measured access times to ata_host::lock
spinlock (since interrupt handler code is fully embraced with
this lock). The average lock's holdtime decreased eight times
while average waittime decreased two times.
Both before and after the change the transfer time is the same,
while 'perf record -e cycles:k ...' shows 1%-4% CPU time spent
in ahci_single_irq_intr() routine before the update and not even
sampled/shown ahci_single_irq_intr() after the update.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
As described in AHCI v1.0 specification chapter 10.6.2.2
"Multiple MSI Based Messages" generation of interrupts
is not controlled through the HOST_IRQ_STAT register.
Considering MMIO access is expensive remove unnecessary
reading and writing of HOST_IRQ_STAT register.
Further, serializing access to the host data is no longer
needed and the interrupt service routine can avoid competing
on the host lock.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Suggested-by: "Jiang, Dave" <dave.jiang@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Jiang, Dave" <dave.jiang@intel.com>
Cc: linux-ide@vger.kernel.org
Currently host activation done by calling either function
ahci_host_activate() or ata_host_activate(). Consolidate
the code by only calling ahci_host_activate() for all AHCI
devices.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
This update is a prerequisite for consolidation of
AHCI host activation code within ahci_host_activate()
function.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
This patch moves force_port_map and mask_port_map into the
ahci_host_priv structure. This allows to modify them into the AHCI
framework. This is needed by the new dt bindings representing ports as
the port_map mask is computed automatically.
Parameters modifying force_port_map, mask_port_map and flags have been
removed from the ahci_platform_init_host() function, and inputs in the
ahci_host_priv structure are now directly filed.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The subsequent patch will make use of them.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting - another ahci platform driver variant,
additional controller support, minor fixes and cleanups"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device ID for HighPoint RocketRaid 642L
ata: ep93xx: use dmaengine_prep_slave_sg api instead of internal callback
ahci: add PCI ID for Marvell 88SE91A0 SATA Controller
sata_fsl: remove check for CONFIG_MPC8315_DS
ahci: add support for Hisilicon sata
libahci_platform: add host_flags parameter in ahci_platform_init_host()
ata: ahci: append new hflag AHCI_HFLAG_NO_FBS
ata: use CONFIG_PM_SLEEP instead of CONFIG_PM where applicable in host drivers
ata: ahci_mvebu: new driver for Marvell Armada 380 AHCI interfaces
Documentation: dt-bindings: reformat and order list of ahci-platform compatibles
libata-sff: remove dead code
ata: SATL compliance for Inquiry Product Revision
pata_octeon_cf: use devm_kzalloc() to allocate cf_port
Append AHCI_HFLAG_NO_FBS to force turning off FBS flag.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
On Intel Valleyview SoC, SATA device sleep is not reliable. When
DEVSLP is attempted on certain SSDs, port_devslp write would fail
and result in malfunction of AHCI controller. AHCI controller may
be not shown in PCI enumeration after reset. Complete power source
removal may be required to recover from this failure. So we blacklist
this device and override host device reported capabilities such that
device LPM will only attempt slumber but not DEVSLP.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Unreferenced casts of void * types are unnecessary so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Allwinner A10 and A20 ARM SoCs have an AHCI sata controller which needs a
special register to be poked before starting the DMA engine.
This register gets reset on an ahci_stop_engine call, so there is no other
place then ahci_start_engine where this poking can be done.
This commit allows drivers to override ahci_start_engine behavior for use by
the Allwinner AHCI driver (and potentially other drivers in the future).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
sparse says:
drivers/ata/libahci.c:1390:5: warning:
symbol 'ahci_pmp_retry_softreset' was not declared. Should it be static?
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch marks the function ahci_port_intr() and
ahci_hw_port_interrupt() as static in libahci.c because they are not
used outside this file.
Thus, it also eliminates the following warnings in libahci.c:
drivers/ata/libahci.c:1767:6: warning: no previous prototype for ‘ahci_port_intr’ [-Wmissing-prototypes]
drivers/ata/libahci.c:1800:6: warning: no previous prototype for ‘ahci_hw_port_interrupt’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Pull libata changes from Tejun Heo:
"Nothing too interesting. Only two minor fixes in libata core. Most
changes are specific to hardware which isn't too common"
* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device IDs for Intel Wildcat Point-LP
sata_rcar: Convert to clk_prepare/unprepare
drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH drive
libata: Add some missing command descriptions
sata_highbank: clear whole array in highbank_initialize_phys()
ahci: disabled FBS prior to issuing software reset
libata: Fix display of sata speed
ahci: imx: setup power saving methods
ata_piix: minor typo and a printk fix
ahci: Changing two module params with static and __read_mostly
Tested with Marvell 88se9125, attached with one port mulitplier(5 ports)
and one disk, we will get following boot log messages if using current
code:
ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f
ahci 0000:03:00.0: FBS is enabled
ata8.00: hard resetting link
ata8.00: SATA link down (SStatus 0 SControl 330)
ata8.01: hard resetting link
ata8.01: SATA link down (SStatus 0 SControl 330)
ata8.02: hard resetting link
ata8.02: SATA link down (SStatus 0 SControl 330)
ata8.03: hard resetting link
ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133)
ata8.04: hard resetting link
ata8.04: failed to resume link (SControl 133)
ata8.04: failed to read SCR 0 (Emask=0x40)
ata8.04: failed to read SCR 0 (Emask=0x40)
ata8.04: failed to read SCR 1 (Emask=0x40)
ata8.04: failed to read SCR 0 (Emask=0x40)
ata8.03: native sectors (2) is smaller than sectors (976773168)
ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133
ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata8.03: configured for UDMA/133
ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100)
ata8.15: hard resetting link
ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
ata8.15: PMP revalidation failed (errno=-19)
ata8.15: hard resetting link
ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
ata8.15: PMP revalidation failed (errno=-19)
ata8.15: limiting SATA link speed to 3.0 Gbps
ata8.15: hard resetting link
ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
ata8.15: PMP revalidation failed (errno=-19)
ata8.15: failed to recover PMP after 5 tries, giving up
ata8.15: Port Multiplier detaching
ata8.03: disabled
ata8.00: disabled
ata8: EH complete
The reason is that current detection code doesn't follow AHCI spec:
First,the port multiplier detection process look like this:
ahci_hardreset(link, class, deadline)
if (class == ATA_DEV_PMP) {
sata_pmp_attach(dev) /* will enable FBS */
sata_pmp_init_links(ap, nr_ports);
ata_for_each_link(link, ap, EDGE) {
sata_std_hardreset(link, class, deadline);
if (link_is_online) /* do soft reset */
ahci_softreset(link, class, deadline);
}
}
But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software
reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to
'0'.
The patch test ok with kernel 3.11.1.
tj: Patch white space contaminated, applied manually with trivial
updates.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
If EM Transmit bit is busy during init ata_msleep() is called. It is
wrong - msleep() should be used instead of ata_msleep(), because if EM
Transmit bit is busy for one port, it will be busy for all other ports
too, so using ata_msleep() causes wasting tries for another ports.
The most common scenario looks like that now
(six ports try to transmit a LED meaasege):
- port #0 tries for the 1st time and succeeds
- ports #1-5 try for the 1st time and sleeps
- port #1 tries for the 2nd time and succeeds
- ports #2-5 try for the 2nd time and sleeps
- port #2 tries for the 3rd time and succeeds
- ports #3-5 try for the 3rd time and sleeps
- port #3 tries for the 4th time and succeeds
- ports #4-5 try for the 4th time and sleeps
- port #4 tries for the 5th time and succeeds
- port #5 tries for the 5th time and sleeps
At this moment port #5 wasted all its five tries and failed to
initialize. Because there are only 5 (EM_MAX_RETRY) tries available
usually only five ports succeed to initialize. The sixth port and next
ones usually will fail.
If msleep() is used instead of ata_msleep() the first port succeeds to
initialize in the first try and next ones usually succeed to
initialize in the second try.
tj: updated comment
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In order to save power consumption as much as possible.
* Disable sata phy internal pll reference clock when sysetem enter
into suspend mode, enable it after resume.
* Setup module parameter used to enable imx ahci test power down
mode(PDDQ) or not, when there is no device detected on the port
* minor modifications:
- The format of the copyright is changed, because that the original
one can't pass fsl internal patch reivew without the character
'(c)'.
- Exports ahci_platform_ops and ahci_error_handler().
NOTE:
* The hot-plug can't be supported when PDDQ mode is ever enabled.
* module parameter usage how-to:
- default: enable PDDQ mode when no device detected.
- add "ahci-imx.hotplug=1" into kernel command line if your don't
want to enable PDDQ mode when no device detected on the port.
tj: Slightly updated description and comments.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here module parameters ahci_em_messages and devslp_idle_timeout can
be set as static and __read_mostly.
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.
Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes. The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times. The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_hardreset() and ahci_p5wdh_hardreset() use bare numbers for the
BSY bit of the ATA status register, despite it's #define'd in
<linux/ata.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2
Reported-by: Yu Liu <liuyu.ac@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Create a new ata_port_operations function pointer called
transmit_led_message and give it the default value of
ahci_transmit_led_message. This allows AHCI controllers with
non-standard LED interfaces to use the existing em_ interface.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff moved on to a greener pasture.
s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Take advantage of multiple MSIs implementation on x86 - on
systems with IRQ remapping AHCI ports not only get assigned
separate MSI vectors - but also separate IRQs. As result,
interrupts generated by different ports could be serviced on
different CPUs rather than on a single one.
In cases when number of allocated MSIs is less than requested
the Sharing Last MSI mode does not get used, no matter
implemented in hardware or not. Instead, the driver assumes the
advantage of multiple MSIs is negated and falls back to the
single MSI mode as if MRSM bit was set (some Intel chips
implement this strategy anyway - MRSM bit gets set even if the
number of allocated MSIs exceeds the number of implemented ports).
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/15bf7ee314dd55f21ec7d2a01c47613cd8190a7c.1353324359.git.agordeev@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either
because it is only the sufficient condition of Identify Device data
log, not the necessary condition.
This patch replaced ata_device->sata_settings with ->devslp_timing
to only save DevSlp timing variables(8 bytes), instead of the whole
SATA Settings page(512 bytes).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=51881
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using ata_link_warn() instead of ata_link_printk().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal.
This feature enables an HBA and SATA storage device to enter the DevSleep
interface state, enabling lower power SATA-based systems.
Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as
soon as there are no commands outstanding to the device and the port
specific Device Sleep idle timer has expired. This enables autonomous
entry into the DevSleep interface state without waiting for software
in power sensitive systems.
This patch enables Aggressive Device Sleep only if both host controller
and device support it.
Tested on AMD reference board together with Device Sleep supported device
sample.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Aaron Lu <aaron.lwe@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make ahci_dev_classify available to the ahci platform driver for custom
hard reset function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following commit was intended to fix problems with specific AHCI
controller(s) that would become bricks if the AHCI specification was not
followed strictly (that is, if ahci_start_engine() was called while the
controller was in the wrong state):
commit 7faa33da9b
ahci: start engine only during soft/hard resets
However, some devices currently have issues with that fix, so we must
implement a flag that delays the ahci_start_engine() call only for specific
controllers.
This commit simply introduces the flag, without enabling it in any driver.
Note that even when AHCI_HFLAG_DELAY_ENGINE is not enabled, this patch does
not constitue a full revert to commit 7faa33da; there is still a change in
behavior to the ahci_port_suspend() failure path.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Linus Torvalds
Dan Williams
Xiangliang Yu
Dan Williams
Manuel Lauss
Robert Richter
Suman Tripathi
Gabriele Mazzotta
Tejun Heo
Alexander Gordeev
Antoine Ténart
Kefeng Wang
Jacob Pan
Joe Perches
Hans de Goede
Daeseok Youn
Paul Gortmaker
Rashika Kheria
xiangliang yu
Lukasz Dorau
Richard Zhu
Chuansheng Liu
Sergei Shtylyov
Shane Huang
Mark Langsdorf
Wei Yongjun
Rob Herring
Brian Norris