mmc_gpiod_free_cd() is paired with mmc_gpiod_request_cd()
and both must reference the same device which is the
actual host controller device not the mmc_host class
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.
For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previously only the ACPI PM domain was supported by the sdio bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Checks EXT_CSD_PARTITION_SETTING_COMPLETED bit before
computing enhanced user area offset and size, and
adding mmc general purpose partitions. The two needs
EXT_CSD_PARTITION_SETTING_COMPLETED bit be set to be
valid (as described in JEDEC standard).
Warn user in case of misconfiguration.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace ext_csd "enhanced_area_en" attribute by
"partition_setting_completed". It was used whether or
not enhanced user area is defined and without checks of
EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move code that manages user area and general purpose
partitions into functions.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This switches the central MMC OF parser to use gpio descriptors
instead of grabbing GPIOs explicitly from the device tree.
This strips out an unecessary use of the integer-based GPIO
API that we want to get rid of, cuts down on code as the
gpio descriptor code will handle active low flags.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This makes it possible to get the write protect (read only)
GPIO line from a GPIO descriptor. Written to exactly mirror
the card detect function.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the slot GPIO driver gets the GPIO to be used for card
detect, it is now possible to specify a flag to have the line
set up as input. Get rid of the explicit setup call for input
and use the flag.
The extra argument works as there are transition varargs
macros in place in the <linux/gpio/consumer.h> header, in
the future we will make the flags argument compulsory.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even (e)MMC card can support 3.3v to 1.2v vccq in DDR, but not all
host controller can support this, like some of the SDHCI host
which connect to an eMMC device. Some of these host controller
still needs to use 1.8v vccq for supporting DDR mode.
So the sequence will be:
if (host and device can both support 1.2v IO)
use 1.2v IO;
else if (host and device can both support 1.8v IO)
use 1.8v IO;
so if host and device can only support 3.3v IO, this is the last choice.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Tested-by: Jean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.
For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.
This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().
Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:
dwmmc_exynos 12220000.mmc: Failed getting OCR mask: -22
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
781e989cf5 ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec66b ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently when the device secure discard implementation is
blacklisted (MMC_QUIRK_SEC_ERASE_TRIM_BROKEN quirk is set)
instead of secure discard we're going to do normal discard,
which is wrong.
When the secure discard is known to be broken we should just
disallow it entirely and not advertise this functionality to
the user. Fix it.
Also move mmc_fixup_device() in from of mmc_blk_alloc() so we
can get quirks set before we attempt to set queue information.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As stated by the eMMC 5.0 specification, a chip should not be rejected
only because of the revision stated in the EXT_CSD_REV field of the
EXT_CSD register.
Remove the control on this value, the control of the CSD_STRUCTURE field
should be sufficient to reject future incompatible changes.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initialization of some SD-cards fails because the card never
leaves the busy state. Aid trouble shooting by indicating this in the
kernel log.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for an output like this:
> mmcblk mmc1:0001: calling add_quirk_mmc+0x0/0x20
Instead use this one:
> mmcblk mmc1:0001: calling add_quirk_mmc
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The runtime PM core handles a runtime_idle callback set to NULL as one
returning 0. So, let's just set it to NULL instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Rather than the SDIO support spawning it's own thread for handling card
interrupts, use the generic IRQ infrastructure for this, triggering it
from the host interface's interrupt handling directly.
This avoids a race between the parent thread waiting to receive an
interrupt response from the card, and the slow startup from the sdio
irq thread, which can occur as a result of high system load (eg, while
udev is running.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Callers of mmc_regulator_get_supply could benefit from knowing if either
of the regulators are present but not yet available. Since callers do
not currently examine the return value, modify this function to return
zero or -EPROBE_DEFER if either regulator get returns the same.
Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal
with absent regulators, switch to devm_regulator_get_optional. This has
the added benefit of allowing this function to behave correctly even in
the !CONFIG_REGULATOR case such that the stub can be removed.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host,
for those host driver's that can't distinguish this in runtime.
Specially, if host can support HS400, it means that host can also
support HS200.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high
speed DDR interface timing from HS200. Clock frequency is up to 200MHz
and only 8-bit bus width is supported. In addition, tuning process of
HS200 is required to synchronize the command response on the CMD line
because CMD input timing for HS400 mode is the same as HS200 mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Jackey Shen <jackey.shen@amd.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Current implementation for bus speed mode selection is too
complicated. This patch is to simplify the codes and remove
some duplicate parts.
The following changes are including:
* Adds functions for each mode selection(HS, HS-DDR, HS200 and etc)
* Rearranged the mode selection sequence with supported device type
* Adds maximum speed for HS200 mode(hs200_max_dtr)
* Adds field definition for HS_TIMING of EXT_CSD
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Power class is changed once only after selection of bus modes
including speed and bus-width finishes finally.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Device types which are supported by both host and device can be
identified when EXT_CSD is read. There is no need to check host's
capability anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The eMMC signalling voltage is determined by VCCQ which is provided to
the card by the host. Signalling is not required to begin at 3.3v and,
if the host and card both support a particular VCC/VCCQ combination, it
can be used immediately.
In contrast, SD Cards must begin with 3.3v signalling and may switch to
a lower voltage signalling if instructed to do so in CMD11. A message
is required to coordinate this operation because the card only receives
a 3.3v VDD and must know when to use the 1.8v produced by its internal
regulator.
It makes sense for the core to begin with 3.3v signalling but when that
can't be set, 1.8v and 1.2v signalling also should be attempted. This
is especially important when an external regulator with a limited range
is used to supply VCCQ to an eMMC part.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The sdio func device is added to the driver model after the card
device.
This means the sdio func device will be suspend before the card device
and thus resumed after. The consequence are the mmc core don't
explicity need to protect itself from receiving sdio requests in
suspended state. Instead that can be handled from the sdio bus, which
is thus invokes the PM callbacks instead of old dummy function.
In the case were the sdio func driver don't implement the PM callbacks
the mmc core will in the early phase of system suspend, remove the
card from the driver model and thus power off it.
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: xiaoming wang <xiaoming.wang@intel.com>
Tested-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
When plugging a specific micro SD card at MMC socket of a custom i.MX28 board,
we get the following kernel warning:
WARNING: CPU: 0 PID: 30 at drivers/mmc/host/mxs-mmc.c:342 mxs_mmc_start_cmd+0x34c/0x378()
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:1 Not tainted 3.14.0-rc5 #8
Workqueue: kmmcd mmc_rescan
[<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14)
[<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c)
[<c001daf8>] (warn_slowpath_common) from [<c001db34>] (warn_slowpath_null+0x1c/0x24)
[<c001db34>] (warn_slowpath_null) from [<c0349478>] (mxs_mmc_start_cmd+0x34c/0x378)
[<c0349478>] (mxs_mmc_start_cmd) from [<c0338fa0>] (mmc_start_request+0xc4/0xf4)
[<c0338fa0>] (mmc_start_request) from [<c03390b4>] (mmc_wait_for_req+0x50/0x164)
[<c03390b4>] (mmc_wait_for_req) from [<c03405b8>] (mmc_app_send_scr+0x158/0x1c8)
[<c03405b8>] (mmc_app_send_scr) from [<c033ee1c>] (mmc_sd_setup_card+0x80/0x3c8)
[<c033ee1c>] (mmc_sd_setup_card) from [<c033f788>] (mmc_sd_init_card+0x124/0x66c)
[<c033f788>] (mmc_sd_init_card) from [<c033fd7c>] (mmc_attach_sd+0xac/0x174)
[<c033fd7c>] (mmc_attach_sd) from [<c033a658>] (mmc_rescan+0x25c/0x2d8)
[<c033a658>] (mmc_rescan) from [<c003597c>] (process_one_work+0x1b4/0x4ec)
[<c003597c>] (process_one_work) from [<c0035de4>] (worker_thread+0x130/0x464)
[<c0035de4>] (worker_thread) from [<c003c824>] (kthread+0xb4/0xd0)
[<c003c824>] (kthread) from [<c000f420>] (ret_from_fork+0x14/0x34)
The error is due to an invalid value in CSD register of a specific 2GB
micro SD card. The CSD version of this card is 1.0 but the TACC field
has the invalid value 0.
cid:0000005553442020000000000000583f
csd:00000032535a83bfedb7ffbf1680003f
date:08/2005
erase_size:512
fwrev:0x0
hwrev:0x0
manfid:0x000000
name:USD
oemid:0x0000
preferred_erase_size:4194304
scr:0225000000000000
serial:0x00000000
type:SD
Since the kernel is making use of this TACC field to calculate the SD
card timeout, an invalid value 0 leads to a warning at
mxs_ns_to_ssp_ticks() and later the following misleading error message
appears in a loop:
mxs-mmc 80010000.ssp: card claims to support voltages below defined range
mxs-mmc 80010000.ssp: no support for card's volts
mmc0: error -22 whilst initialising MMC card
This error is only found on this 2GB SD card on mxs platform.
On x86 this card works without any problems.
The following patch based on the work of Peter Chan and Otavio Salvador.
It catches the case that the determined timeout is still 0 and sets it
to a valid value.
Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use new ATTRIBUTE_GROUPS macro to declare attribute groups.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This change removes the callback from atomic context which it doesn't
need to be in, and puts it in line with the debounced rescan.
This code is based on these e-mail threads with Christian Daudt:
https://lkml.org/lkml/2013/8/19/539https://lkml.org/lkml/2014/3/19/79
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
Add functions to request a CD GPIO using the GPIO descriptor API.
Note that the new request function is paired with mmc_gpiod_free_cd()
not mmc_gpio_free_cd(). Note also that it must be called prior to
mmc_add_host() otherwise the caller must also call
mmc_gpiod_request_cd_irq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
In preparation for adding a descriptor-based CD GPIO API, split out
CD IRQ request into a separate function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
In preparation for adding a descriptor-based CD GPIO API, switch from
recording GPIO numbers to recording GPIO descriptors.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
When sending the sleep command for host drivers supporting
MMC_CAP_WAIT_WHILE_BUSY, we need to confirm that max_busy_timeout is
big enough comparing to the sleep timeout specified from card's
EXT_CSD. If this isn't case, we use a R1 response instead of R1B and
fallback to use a delay instead.
Do note that a max_busy_timeout set to zero by the host, is interpreted
as it can cope with whatever timeout the mmc core provides it with.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Conform to the eMMC spec and use the CMD6 generic timeout from the
EXT_CSD register, when switching to HS200 mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
If the host controller supports busy detection in HW, we expect the
MMC_CAP_WAIT_WHILE_BUSY to be set. Likewise the corresponding
host->max_busy_timeout should reflect the maximum busy detection
timeout supported by the host.
Previously we expected a host that supported MMC_CAP_WAIT_WHILE_BUSY to
cope with any timeout, which just isn't feasible due to HW limitations.
For most switch operations, R1B responses are expected and thus we need
to check for busy detection completion. To cope with cases where the
requested busy detection timeout is greater than what the host are able
to support, we fallback to use a R1 response instead. This will prevent
the host from doing HW busy detection.
In those cases, busy detection completion is handled by polling the for
the card's status using CMD13. This is the same mechanism used when the
host doesn't support MMC_CAP_WAIT_WHILE_BUSY.
Do note, a host->max_busy_timeout set to zero, is interpreted by the
mmc core as it don't know what the host supports. It will then provide
the host with whatever timeout the mmc core finds suitable.
For some cases the mmc core has unfurtunate no clue of what timeout to
use. In these cases we provide the host with a timeout value of zero,
which the host may interpret as use whatever timeout it finds suitable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Instead of using several references to card->host, let's use a local
variable. That means we can remove the BUG_ON verifications for the
same pointers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.
This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.
Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
There are no reason to why the use of a non-volatile internal eMMC
cache should be controlled by a host cap. Instead let's just enable it
if the eMMC card supports it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Earlier we disabled the cache during suspend, which meant a flush was
internally at the eMMC performed as well.
To simplify code we can make use of the mmc_flush_cache(), during mmc
suspend, which makes the mmc_cache_ctrl() redundant so then we can
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
There are no active users of this host capability. The primary reason
for adding this cap was due to a bug in ux500 boot loader code, which
is not a relevant issue any more. So, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Due to the removal of the Kconfig option MMC_UNSAFE_RESUME, several
validations of a present bus_ops callback became redundant. Let's
remove these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Invoking system suspend or shutdown without using the Kconfig option
MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card.
To improve the situation, change the behavior to always make use of the
available bus_ops callbacks that handles system suspend and shutdown
properly.
By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- Avoid get_cd() on cards marked nonremovable.
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC.
- dwmmc: Support Hisilicon K3 SoC controllers.
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM.
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540.
- tegra: Support Tegra124 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wZBx
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.14:
Core:
- Avoid get_cd() on cards marked nonremovable
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC
- dwmmc: Support Hisilicon K3 SoC controllers
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540
- tegra: Support Tegra124 SoCs"
* tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (55 commits)
mmc: sdhci-pci: Fix possibility of chip->fixes being null
mmc: sdhci-pci: Fix BYT sd card getting stuck in runtime suspend
mmc: sdhci: Allow for long command timeouts
mmc: sdio: add a quirk for broken SDIO_CCCR_INTx polling
mmc: sdhci: fix lockdep error in tuning routine
mmc: dw_mmc: k3: remove clk_table
mmc: dw_mmc: fix dw_mci_get_cd
mmc: dw_mmc: fix sparse non static symbol warning
mmc: sdhci-esdhc-imx: fix warning during module remove function
mmc: sdhci-esdhc-imx: fix access hardirq-unsafe lock in atomic context
mmc: core: sd: implement proper support for sd3.0 au sizes
mmc: atmel-mci: add vmmc-supply support
mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield
mmc: sdhci: add quirk for broken HS200 support
mmc: arasan: Add driver for Arasan SDHCI
mmc: dw_mmc: add dw_mmc-k3 for k3 platform
mmc: dw_mmc: use slot-gpio to handle cd pin
mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts
mmc: sdhci-pci: break out definitions to header file
mmc: tmio: fixup compile error
...
Conflicts:
MAINTAINERS
Polling SDIO_CCCR_INTx could create a fake interrupt with Marvell
SD8797 card. Add a quirk to handle this case. The fixup here is
to issue a dummy CMD52 read to function 0 register 0xff, and this
dummy read must be right after SDIO_CCCR_INTx is read.
Patch has been verified on a dw_mmc controller (Samsung Chromebook)
with MMC_CAP_SDIO_IRQ disabled.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This reverts and updates commit 77776fd0a4 ("mmc: sd: fix the
maximum au_size for SD3.0"). The au_size for SD3.0 cannot be achieved
by a simple bit shift, so this needs to be implemented differently.
Also, don't print the warning in case of 0 since 'not defined' is
different from 'invalid'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: stable <stable@vger.kernel.org> # [3.12, 3.13]
Signed-off-by: Chris Ball <chris@printf.net>
Non removable cards are always present, so do not call get_cd for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC_CAP_UHS_DDR50 must work on 1.8v.
However, the eMMC DDR mode can work on either 1.8v or 3.3v and
should not depend on UHS_DDR50.
So get rid of this limitation to let controller without 1.8v
signal voltage support can also work for eMMC DDR mode if it claims.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Modify acpi_preset_companion() to take a struct acpi_device pointer
instead of an ACPI handle as its second argument and redefine it as
a static inline wrapper around ACPI_COMPANION_SET() passing the
return value of acpi_find_child_device() directly as the second
argument to it. Update its users to pass struct acpi_device
pointers instead of ACPI handles to it.
This allows some unnecessary acpi_bus_get_device() calls to be
avoided.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Aaron Lu <aaron.lu@intel.com> # for ATA binding
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=JDGc
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
In some environments it is to prefer to postpone the resume of the card
device until runtime_resume is being carried out, since it will mean a
signficant decrease of the total system resume time.
The reason of the decreased resume time is simply because of the actual
re-initalization of the card, which typically takes hundreds of
milliseconds, is performed outside the resume sequence and wont thus
affect it.
For removable card, the detect work tries to re-detect the card to make
sure it is still present, as a part of that sequence the card will also
be runtime_resumed and thus also fully resumed.
For a non-removable card, typically a mmc blk request will trigger a
runtime_resume and thus fully resume the card. This also means the
first request will likely suffer from an inital latency since the
re-initialization of the card needs to be performed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The card device is considered as in-active after it has been suspended.
To prevent any further runtime PM requests in suspend state, we then
disable runtime PM.
After the card device has been resumed, we shall consider it as active,
like we also do after a probe sequence. When resumed, we can safely
enable runtime PM again.
This will make sure the PM core can request the card device to go to
in-active state after a resume has been completed. Previously we had to
wait for new pm_runtime_get->pm_runtime_put cycle to be executed.
Additionally, once a resume has been carried out, update the last busy
mark. At the moment this will have no effect but if the PM core will
respect autosuspend enabled devices, when it directly triggers a
runtime_suspend from a runtime_idle, it will mean the card device will
be scheduled for a delayed runtime_suspend instead of done immediately.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: core: Push common suspend|resume code into each bus_ops"
moved the responsibility for doing mmc_power_up|off into each
suspend/resume bus_ops. When using MMC_CAP_AGGRESSIVE_PM, through the
runtime callbacks, calls to mmc_power_up|off became redundant.
When removing them, we are also able to remove the calls to
mmc_claim|release_host, thus simplifing code a bit more.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By adding a card state that records if it is suspended or resumed, we
can accept asyncronus suspend/resume requests for the mmc and sd
bus_ops.
MMC_CAP_AGGRESSIVE_PM, will at request inactivity through the runtime
bus_ops callbacks, execute a suspend of the the card. In the state were
this has been done, we can receive a suspend request for the mmc bus,
which for sd and mmc forced the card to active state by a
pm_runtime_get_sync. In other words, the card was resumed and then
immediately suspended again, completely unnecessary.
Since the suspend/resume bus_ops callbacks for sd and mmc are now
capable of handling asynchronous requests, we no longer need to force
the card to active state before executing suspend. Evidently preventing
the above sequence for MMC_CAP_AGGRESSIVE_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The are no more users of the deprecated mmc_suspend|resume_host API,
so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We want to give user space provision to fully consume a card
insert/remove event, when the event was caused by a wakeup irq.
By signaling the wakeup event for a time of 5 s for devices configured
as wakeup capable, we likely will be prevent a sleep long enough to let
user space consume the event.
To enable this feature, host drivers must thus configure their devices
as wakeup capable.
This is a reworked implementation of the old wakelocks for the mmc
subsystem, originally authored by Colin Cross and San Mehat for the
Android kernel. Zoran Markovic shall also be given cred for recently
re-trying to upstream this feature.
Cc: San Mehat <san@google.com>
Cc: Colin Cross <ccross@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Zoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since mmc_select_voltage now only gets called from the attach sequence,
it makes sense to move the out of spec validations of the card ocr into
this function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to eMMC/SD/SDIO specs, the VDD (VCC) voltage level must be
maintained during the initialization sequence. If we want/need to tune
the voltage level, a complete power cycle of the card must be executed.
Most host drivers conforms to the specifications by only allowing to
change VDD voltage level at the MMC_POWER_UP state, but some also cares
about MMC_POWER_ON state, which they should'nt. This patch will not
break those drivers, but they could clean up code to better reflect
what is expected from the protocol layer.
A big re-work of the mmc_select_voltage function is done to only change
VDD voltage level if the host supports MMC_CAP2_FULL_PWR_CYCLE.
Otherwise only validation of the host and card ocr mask will be done.
A very nice side-effect of this patch is that we now don't need to
reset the negotiated ocr mask at the mmc_power_off function, since now
it will actually reflect the present voltage level, which safely can be
used at the next power up and re-initialization. Moreover, we then only
need to execute mmc_select_voltage from the attach sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The negotiated ocr mask is directly related to the card. Once a card
gets removed, the mask shall be dropped. By moving the cache of the ocr
mask from the host struct to the card struct we have accomplished this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
At several places in mmc_sdio_init_card function the cached mask in
host->ocr were being updated. To simplify code, we make use of an
local ocr parameter instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The retry and fallback mechanism when failing to switch to 1.8V
signaling voltage is handled by the SDIO card init function. Thus we
can remove the duplicated old code from the attach function.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is yet another step of restructure code to be able to fixup the
setup of the negotiated ocr mask.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As a step to fixup the setup of the negotiated ocr mask, we need the
mmc_power_up|cycle functions to take the ocr as a parameter.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some switch operations like poweroff notify, shall according to the
spec not be followed by any other new commands. For these cases and
when the host does'nt support MMC_CAP_WAIT_WHILE_BUSY, we must not
send status commands to poll for busy detection. Instead wait for
the stated timeout from the EXT_CSD before completing the request.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the MMC bus code to use the
correct field.
Cc: Chris Ball <cjb@laptop.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Konstantin Dorfman <kdorfman@codeaurora.org>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While speed mode is changed, CMD13 cannot be guaranteed.
According to the spec., it is not recommended to use CMD13
to check the busy completion of the timing change.
If CMD13 is used in this case, CRC error must be ignored.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
cscope says there are no callers for mmc_try_claim_host in the kernel.
No reason to keep it.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=+EYB
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
Add function to support getting voltage from device-tree.
If voltage-range is specified in device-tree node, this function
will parse it and return the available voltage mask.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since SD Physical Layer specification V3.0, AU_SIZE is supported up
to 0xf. So If SD-card is supported v3.0, then max_au should be 0xf.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In function mmc_sd_init_card, if command 3/9/7 got failed, mmc_card
allocated just before won't be freed. This would cause memory leak.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use regulator_get_optional() to tell the core that requests for the vmmcq
regulator can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Core:
- Add support for eMMC 5.1 devices.
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power management
of eMMC/SD between requests, using runtime PM.
- Add an ioctl to perform the eMMC 4.5 Sanitize command; sample code at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs.
- dw_mmc: Add support for Altera SoCFPGAs.
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable cards.
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs.
- sdhi/tmio: Add DT DMA support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=c/CM
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.11:
Core:
- Add support for eMMC 5.1 devices
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power
management of eMMC/SD between requests, using runtime PM
- Add an ioctl to perform the eMMC 4.5 Sanitize command. Sample code
at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs
- dw_mmc: Add support for Altera SoCFPGAs
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable
cards
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs
- sdhi/tmio: Add DT DMA support"
* tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (87 commits)
mmc: bcm281xx SDHCI driver
mmc: sdhci: add card_event callback to sdhci
mmc: core: Fixup Oops for SDIO shutdown
mmc: sdhci-pci: add another device id
mmc: esdhc: Fix bug when writing to SDHCI_HOST_CONTROL register
mmc: esdhc: Add support for 8-bit bus width and non-removable card
mmc: core: production year for eMMC 4.41 and later
mmc: omap: remove unnecessary #if 0's
mmc: sdhci: fix ctrl_2 on super-speed selection
mmc: dw_mmc-pltfm: add Rockchip variant
mmc: dw_mmc-pltfm: move probe and remove below dt match table
mmc: dw_mmc-pltfm: remove static from dw_mci_pltfm_remove
mmc: sdhci-acpi: add support for eMMC hardware reset for HID 80860F14
mmc: sdhci-pci: add support for eMMC hardware reset for BYT eMMC.
mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
mmc: sdhci: fix caps2 for HS200
sdhci-pxav3: Fix runtime PM initialization
mmc: core: Add DT-bindings for MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Invent MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Enable power_off_notify for eMMC shutdown sequence
...
Commit "mmc: core: Handle card shutdown from mmc_bus" introduced an
Oops in the shutdown sequence for SDIO.
The drv pointer, does not exist for SDIO since the probing of the SDIO
card from the mmc_bus perspective is expected to fail by returning
-ENODEV.
This patch adds the proper check for the pointer before calling it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The field containing the production date in the CID register only uses
4 bits to encode the year, starting from 1997 in the original standard.
In 2013, the production year field contains 0, and the kernel reports a
1997 production date.
The eMMC 4.51 specification adds a new interpretation rule. For all
devices implementing the 4.41 specification or later, the production
year field will be interpreted as a value between 2010 and 2025, with
0 corresponding to 2013.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The DT-binding for MMC_CAP2_FULL_PWR_CYCLE, is used to indicate whether
it is possible to perform a full power cycle of the card.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC_CAP2_FULL_PWR_CYCLE shall be set by host drivers which are able to
do a complete power cycle of the card. In the eMMC case that includes
both vcc and vccq.
This CAP is providing the protocol layer with important information,
needed to take optimized decisions during card initialization and in
the suspend/resume sequence.
MMC_CAP2_POWEROFF_NOTIFY is replaced by MMC_CAP2_FULL_PWR_CYCLE, since
it makes sense to use a wider scope for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In suspend mode it is important to save power. If the host is able to
cut buth vcc and vccq, the MMC_CAP2_POWEROFF_NOTIFY shall be set. It
will mean the card will be completely powered down at suspend and the
power off notification cmd will be sent prior power down.
It seems common not being able to cut both vcc and vccq for a host. In
this situation we issue the sleep cmd in favor of the power off
notification cmd, to save more power.
While maintainng the above policy, we also want to make use of the
power off notification in the shutdown sequence, even in the case were
the host has not set MMC_CAP2_POWEROFF_NOTIFY, since we know vcc and
vccq will regardless be cut.
We accomplish this by always enabling the power off notification byte
in the EXT_CSD and issue the power off notification when either
MMC_CAP2_POWEROFF_NOTIFY is set or we are executing a shutdown.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The shutdown sequence of an (e)MMC is very similar to a suspend. We
re-use the suspend function and tell it we are not in suspend context.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Depending on the context of the operation while powering down the card,
either POWER_OFF_NOTIFY_SHORT or POWER_OFF_NOTIFY_LONG will be used. In
suspend context a short timeout is preferred while a long timeout would
be acceptable in a shutdown/hibernation context.
We add a new parameter to the mmc_suspend function so we can provide an
indication of what notification type to use.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For the SD .shutdown callback we re-use the SD suspend function since
it performs the relevant actions.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By adding an optional .shutdown callback to the bus_ops struct we
provide the possibility to let each bus type handle it's shutdown
requirements.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Considering shutdown of the card, the responsibility to initate this
sequence shall be driven from the mmc_bus.
This patch enables the mmc_bus to handle this sequence properly. A new
.shutdown callback is added in the mmc_driver struct which is used to
shutdown the blk device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host should be responsible to suspend|resume the host and not the
card. This patch changes this behaviour, by moving the responsiblity
to the mmc bus instead which already holds the card device.
The exported functions mmc_suspend|resume_host are now to be considered
as depcrecated. Once all host drivers moves away from using them, we
can remove them. As of now, a successful error code is always returned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
By moving code from the mmc_suspend|resume_host down into each
.suspend|resume bus_ops callback, we get a more flexible solution.
Some nice side effects are that we get a better understanding of each
bus_ops suspend|resume sequence and the common code don't have to take
care of specific corner cases, especially for the SDIO case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch moves the validation for all the suspend prerequisites to be
done at SUSPEND_PREPARE notification. Previously in the SDIO case parts
of the validation was done from mmc_suspend_host.
This patch invents a new pre_suspend bus_ops callback and implements it
for SDIO. Returning an error code from it, will mean at SUSPEND_PREPARE
notification, the card will be removed before proceeding with the
suspend sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For every bus_ops type the .remove callback always exist, thus there
are no need to check the existence of it, before we decide to call it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the new eMMC5.1 spec, there is a new EXT_CSD register with
the revision number(EXT_CSD_REV) 7. This patch updates the check
for ext-csd.rev number as 7.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In addition to just logging errors encountered during DT parsing or
allocating GPIO slots for CD/WP, mmc_of_parse() now returns with an error.
In particular, this is needed if the GPIO allocation may return
EPROBE_DEFER.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Use the saved values in card->ext_csd when selecting power class.
By doing this the power class will be selected even if mmc_init_card
is called with oldcard != NULL, which is the case after a suspend/resume.
Today ext_csd is NULL if mmc_init_card is called with oldcard != NULL
and power class will not be selected.
According to the eMMC specification the POWER_CLASS value is reset after
power failure, H/W reset assertion and any CMD0 reset.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Acked By: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.
We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.
Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Aggressive power management is suitable when saving power is
essential. At request inactivity timeout, aka pm runtime
autosuspend timeout, the card will be suspended.
Once a new request arrives, the card will be re-initalized and
thus the first request will suffer from a latency. This latency
is card-specific, experiments has shown in general that SD-cards
has quite poor initialization time, around 300ms-1100ms. eMMC is
not surprisingly far better but still a couple of hundreds of ms
has been observed.
Except for the request latency, it is important to know that
suspending the card will also prevent the card from executing
internal house-keeping operations in idle mode. This could mean
degradation in performance.
To use this feature make sure the request inactivity timeout is
chosen carefully. This has not been done as a part of this patch.
Enable this feature by using host cap MMC_CAP_AGGRESSIVE_PM and
by setting CONFIG_MMC_UNSAFE_RESUME.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO is the only protocol that uses runtime pm for the card device
right now. To provide the option for sd and mmc to use runtime pm as
well the bus_ops callback are extended with two new functions. One for
runtime_suspend and one for runtime_resume.
This patch will also implement the callbacks for SDIO to make sure
existing functionality is maintained. It also prepares to move
away from using the mmc_power_restore_host API, since it is not
needed when using runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move mmc suspend specific operations to be executed from the .suspend
callback in the mmc bus_ops. This simplifies the mmc_suspend_host
function which is supposed to handle nothing but common suspend tasks.
Since eMMC can be considered non-removable there are no need to check
for ongoing bkops at PM_SUSPEND_PREPARE notification so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously the MMC_CAP2_DETECT_ON_ERR was invented for detecting
slow card removal. In was never a realy good solution and a proper
fix has been merged using gpio debouncing instead. We remove this
cap in this patch.
Although when using polling card detect mode, the code invented for
MMC_CAP2_DETECT_ON_ERR is re-used to complete card removal in an
earlier phase. There are no need waiting for the polling timeout to
elapse in this case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only execute tuning for sd and sdio devices that are using
SDR50 or SDR104.
Make sure clock is hold during tuning for sdio devices.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Acked-by: Johan Rudholm <jrudholm@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping mmc_power_up()
at boot/initialization time if it's already happened, for performance
(faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being put
into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed slowly;
we were missing card removal events if the card retained contact with
the slot pads for long enough to reply to a CMD13 while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use mmc_of_parse().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Pr7P
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.10:
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
mmc_power_up() at boot/initialization time if it's already
happened, for performance (faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being
put into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed
slowly; we were missing card removal events if the card retained
contact with the slot pads for long enough to reply to a CMD13
while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use
mmc_of_parse()"
* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
mmc: core: fix init controller performance regression, updated patch
mmc: mxcmmc: enable DMA support on mpc512x
mmc: mxcmmc: constify mxcmci_devtype
mmc: mxcmmc: use slot-gpio API for write-protect detection
mmc: mxcmmc: add mpc512x SDHC support
mmc: mxcmmc: fix race conditions for host->req and host->data access
mmc: mxcmmc: DT support
mmc: dw_mmc: let device core setup the default pin configuration
mmc: mxs-mmc: add broken-cd property
mmc: mxs-mmc: add non-removable property
mmc: mxs-mmc: add cd-inverted property
mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
mmc: mxcmmc: Fix bug when card is present during boot
mmc: core: fix performance regression initializing MMC host controllers
Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
mmc: atmel-mci: pio hang on block errors
mmc: core: Fix bit width test failing on old eMMC cards
mmc: dw_mmc: Use pr_info instead of printk
mmc: dw_mmc: Check return value of regulator_enable
...
Use preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add MMC_CAP2_NO_PRESCAN_POWERUP to sdhci-pci.c also, use mmc_power_off()
for MMC_CAP2_NO_PRESCAN_POWERUP.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[cjb: previously applied v1 of this patch instead of v4]
Signed-off-by: Chris Ball <cjb@laptop.org>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put_noidle in such case.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit fa5501890d introduced a performance
regression by adding mmc_power_up() to mmc_start_host(). mmc_power_up()
is not necessary to host controller initialization, it is part of card
initialization and is performed anyway asynchronously.
This patch allows a driver to leave the power up in asynchronous code
(as it was before).
On my current target platform this reduces driver initialization from:
[ 1.313220] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 102008 usecs
to this:
[ 1.217209] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 8331 usecs
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 3500ed90b2.
The reverted patch caused a significant performance regression when
booting with the root file system on eMMC.
Before the patch:
[ 1.625623] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
After the patch:
[ 1.935851] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
That was an addition of 310 ms which is a 19% performance degradation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
PARTITION_SUPPORT needs to be set before doing the compare on version
number so the bit width test does not get invalid data. Before this
patch, a Sandisk iNAND eMMC card would detect 1-bit width although
the hardware supports 4-bit.
Only affects old emmc devices - pre 4.4 devices.
Reported-by: Elad Yi <elad.yi@gmail.com>
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC hosts are added asynchronously. We need to wait until detect returns to
avoid failed root filesystem mounts.
VFS: Cannot open root device "mmcblk0p1" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
mmc0: host does not support reading read-only switch. assuming write-enable.
1f00 256 mtdblock0 (driver?)
1f01 256 mtdblock1 (driver?)
1f02 2560 mtdblock2 mmc0: new SDHC card at address b368
(driver?)
1f03 29696 mtdblock3 (driver?)
1f04 16384 mtdblock4 mmcblk0: mmc0:b368 USD 3.72 GiB
(driver?)
mmcblk0: p1
b300 3910656 mmcblk0 driver: mmcblk
b301 3906560 mmcblk0p1 00000000-01
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ACPI spec 5 defined the _ADR encoding for sdio bus as:
High word - slot number (0 based)
Low word - function number
This patch adds support for binding sdio function device with acpi node,
and if successful, involve acpi into its power management.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Function _mmc_detect_card_removed will be called to know whether
the card is still present when host->bus_ops->detect is called.
In current code, the return value of this function generally only
depend on the result of sending cmd13 to card, which may not safe
for card with detection support like slot gpio detection.
Because the communication status between host and card may out of
sync with the detect status if remove the card slowly or hands shake
during the process. The direct reason is the async between card
detect switch and card/slot pad contaction in hardware, which is
defined by spec.
The spec define card insert/remove sequence as below (both standard size
SD card and MicroSD card have the same sequence):
"Part 1 Standard Size SD Card Mechanical Addendum Ver4.00 Final,
Appendix C: Card Detection Switch" (Take normally open type as example)
a)SD card insertion sequence:
The card detection switch should be turned on after all SD card
contact pads are connected to the host connector contact pads.
b)SD removal sequence:
The card detection switch should be turned off when the SD card
is just going to be removed and before any SD card contact pad is
disconnected from the host connector contact pad.
Below is the sequence when this issue occur (Take slot gpio detection
as example and remove the card slowly during the process):
1. gpio level changed and card detect interrupt triggered.
2. mmc_rescan was launched.
3. the card pads were still contacted with the slot pads because of slow
removal. So _mmc_detect_card_removed and mmc_rescan think card was
still present (cmd13 succeed).
4. card pads were discontacted from the card slot pads.
So the card was actually removed finally but the card removal event
has been missed by system.
The interval length between step 1 and step 4 depends on the
card removal speed. If it's longer than the detect work schedule
delay which is 200ms, this issue will likely happen.
This patch add the card detect status check in function
_mmc_detect_card_removed if cmd13 check succeed and host->ops->get_cd
provided. If get_cd detect no card present then schedule another detect
work 200ms later.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The JEDEC MMC v4 spec defines a new PRV value in place of the original
fwrev and hwrev specified in v1. We can expose this in the kernel to enable
user space to more easily determine the product revision of a given MMC.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=dYdW
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch supports packed write command of eMMC4.5 devices. Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally. As a result, packed command help
write throughput be improved. The following tables show the results
of packed write.
Type A:
test none | packed
iozone 25.8 | 31
tiotest 27.6 | 31.2
lmdd 31.2 | 35.4
Type B:
test none | packed
iozone 44.1 | 51.1
tiotest 47.9 | 52.5
lmdd 51.6 | 59.2
Type C:
test none | packed
iozone 19.5 | 32
tiotest 19.9 | 34.5
lmdd 22.8 | 40.7
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds packed command feature of eMMC4.5. The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_regulator_set_ocr() depends on the ability of regulator to change the
voltage value. When regulator cannot change its voltage output, some code
is skipped to avoid reporting false errors on some boards, which use MMC
hosts with fixed regulators (e.g. Samsung Goni and UniversalC210 boards).
This patch replaces a hacky workaround based on regulator_count_voltages()
value with the correct call to recently introduced
regulator_can_change_voltage() function in regulators core.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is derived from:
"mmc: fix async request mechanism for sequential read scenarios".
According as async transfer, a request is handled with twice mmc_start_req.
When the card is removed, the request is actually not issued in the first
mmc_start_req [__mmc_start_data_req]. And then mmc_wait_for_data_req_done
will come in the next mmc_start_req. But there is no event for completions.
wake_up_interruptible is needed in __mmc_start_data_req for the case of
removed card.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.
Below are the enhancements introduced by this patch:
1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one. The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.
2. In current code, preset value is disabled at the beginning of
mmc_attach_sd. It's too late since low freq (400khz) should be set in
mmc_power_up. So move preset value disable to sdhci_set_ios which will
be called during power up.
3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.
4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.
This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.
Add a retry mechanism for the SDIO case.
If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.
This patch places a couple of requirements on the host driver:
1) mmc_set_ios with ios.clock = 0 must gate the clock
2) mmc_power_off must actually cut the power to the card
3) The card_busy host_ops member must be implemented
if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.
Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add mmc_power_cycle which can be used to power cycle for instance
SD-cards.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
SET_BLOCK_COUNT CMD23 is needed for all access to RPMB partition. If
block count is not set by CMD23, all subsequent read/write commands fail
as per eMMC specification. So, If the host does not support CMD23, do not
expose RPMB partition.
Accessing RPMB partition can cause hang / huge delay for hosts which do
not support CMD23.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-and-Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cache control is an eMMC feature and in therefore should be
part of MMC's bus resume operations, performed in mmc_suspend,
rather than in the generic mmc_suspend_host().
Signed-off-by: Maya Erez <merez@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.
This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.
With this change read throughput is improved by 16%.
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use devm_* managed functions, so that slot-gpio users do not have to
call mmc_gpio_free_ro/cd to free up resources requested in
mmc_gpio_request_ro/cd.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When SDIO3.0 card is detected, incorrect bus speed mode
is printed as part of card detection print in kernel logs.
This change fixes it so that user won't be confused by
looking at incorrect card detection message in logs.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Jackey Shen <Jackey.Shen@amd.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If SDIO keep power flag (MMC_PM_KEEP_POWER) is not set, card would
be reinitialized during resume but as we are not resetting
(CMD52 reset) the SDIO card during this reinitialization, card may
fail to respond back to subsequent commands (CMD5 etc...).
This change resets the card before the reinitialization of card
during resume.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Chris Ball <cjb@laptop.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Chris Ball <cjb@laptop.org>
The slot-gpio API provides a generic card-detection handler. To support a
wider range of hosts it has to call the host's card-event callback, if
implemented. Also increase the debounce interval to 200ms to match the
SDHCI driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If "caps2" host capabilities does not indicate support for MMC
HS200, don't allow clock speeds >52MHz. Currently, for MMC, the
clock speed is set to the lesser of the max speed the eMMC module
supports (card->ext_csd.hs_max_dtr) or the max base clock of the
host controller (host->f_max based on BASE_CLK_FREQ in the host
CAPS register). This means that a host controller that doesn't
support HS200 mode but has a base clock of 100MHz and an eMMC module
that supports HS200 speeds will end up using a 100MHz clock.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend methods provided by SDIO drivers are not supposed to be called by
the PM core. Instead, when the SDIO core gets to suspend a device's
ancestor, it calls the device driver's suspend routine. However, the PM
core executes suspend callback routines directly for device drivers whose
bus types don't provide suspend callbacks. In consequece, because the
SDIO bus type doesn't provide a suspend callback, the SDIO drivers'
suspend routines will be executed by the PM core (which shouldn't
happen).
To prevent this from happening, add empty system suspend/resume callbacks
for the SDIO bus type.
An analogous change had been made already by commit (e841a7c mmc: sdio:
Use empty system suspend/resume callbacks at the bus level), but then it
was reverted inadvertently by commit (d8e2ac3 mmc: sdio: Fix PM_SLEEP
related build warnings) that attempted to fix build warnings introduced
by commit e841a7c.
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide support for automatically sending Set Block Count
(CMD23) messages. Used at least for RPMB support.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Following JEDEC standard, if the mmc supports RPMB partition,
a new interface is created and exposed via /dev/block.
Users will be able to access RPMB partition using standard
mmc IOCTL commands.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are discrepancies with regards to how MMC capabilities
are carried throughout the subsystem. Let's standardise them
to eliminate any confusion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Before this patch, we always used only single sg entry for SDIO transfer.
This patch switches to using multiple sg entries. In the case of dwmci,
it supports only up to 4KB size per single sg entry. So if we want to
transfer more than 4KB, we should send more than 1 command.
When we tested before applying this patch, it took around 335 us for
5K(5120) bytes transfer with dwmci controller. After applying this patch,
it takes 242 us for 5K bytes. So this patch makes around 38% performance
improvement for 5K bytes transfer. If the transfer size is bigger, then
the performance improvement ratio will be increased.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Add DT properties for card detection (broken-cd, cd-gpios, non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't already
have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qyY5
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
This patch fixes up the broken suspend sequence for eMMC with sleep
support. Additionally it reworks the eMMC4.5 Power Off Notification
feature so it fits together with the existing sleep feature.
The CMD0 based re-initialization of the eMMC at resume is re-introduced
to maintain compatiblity for devices using sleep.
A host shall use MMC_CAP2_POWEROFF_NOTIFY to enable the Power Off
Notification feature. We might be able to remove this cap later on,
if we think that Power Off Notification always is preferred over
sleep, even if the host is not able to cut the eMMC VCCQ power.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Before this patch, we were using MMC_CAP2_BROKEN_VOLTAGE as a way to
avoid calling regulator_set_voltage() on a fixed regulator, but that's
just duplicating information that already exists -- we should test
whether the regulator is fixed directly, instead of via a capability.
This patch implements that test. We can't reclaim the capability bit
just yet, since there are still boards in arch/arm/ that reference it;
those references can be removed now.
Reported-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable eMMC background operations (BKOPS) feature.
If URGENT_BKOPS is set after a response, note that BKOPS are required.
Immediately run BKOPS if required. Read/write operations should be
requested during BKOPS(LEVEL-1), then issue HPI to interrupt the
ongoing BKOPS and service the foreground operation.
(This patch only controls the LEVEL2/3.)
When repeating the writing 1GB data, at a certain time, performance is
decreased. At that time, card triggers the Level-3 or Level-2. After
running bkops, performance is recovered.
Future considerations:
* Check BKOPS_LEVEL=1 and start BKOPS in a preventive manner.
* Interrupt ongoing BKOPS before powering off the card.
* How do we get BKOPS_STATUS value (periodically send ext_csd command)?
* If using periodic bkops, also consider runtime_pm control.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Power management callbacks defined by SIMPLE_DEV_PM_OPS are only used if
the PM_SLEEP Kconfig symbol has been defined. If not, the compiler will
complain about them being unused. However, since the callback for this
driver doesn't do anything it can just as well be dropped.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
It is expected that Extended CSD register (the size of this register
is larger than CID/CSD) will be referenced more frequently as more
fields have been added to Extended CSD and it seems that it is not
a good option to double the memory used.
This patch is intended to avoid the use of bounce buffer for reading
Extended CSD register in mmc_send_cxd_data(). It will provide a better
performance gain by removing memcpy() overhead for a half KiB and
a redundant bounce buffer allocated repeatedly at the cost of providing
DMA-capable buffer from upper caller (but on-stack buffer is allowed
with no performance gain).
Signed-off-by: Kyungsik Lee <kyungsik.lee@lge.com>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_gpio_request_ro() doesn't store the requested gpio in ctx->ro_gpio.
As a result, subsequent calls to mmc_gpio_get_ro() will always fail
with -ENOSYS because the gpio number isn't available to that function.
Cc: stable <stable@vger.kernel.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If MMC_CAP_NONREMOVABLE is set, only issue a detect job on init.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
ext_csd exported through debugfs is printed in reverse order (from
byte 511 to 0), which causes confusion.
Fix the for loop to print ext_csd in natural order.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
HPI can be issued only in programming state to bring the card to
transfer state. If the card is already in transfer state, doing
a HPI is redundant.
Fix this by adding transfer state to the list of exceptions to
doing HPI and return without error.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
system_nrt[_freezable]_wq are now spurious. Mark them deprecated and
convert all users to system[_freezable]_wq.
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant, so there's no reason to use system_nrt[_freezable]_wq.
Please use system[_freezable]_wq instead.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-By: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Add a call to mmc_set_signal_voltage() to set signal voltage to 3.3v in
mmc_power_up so that we do not need to touch signal voltage setting in
mmc/sd/sdio init functions and rescan function.
For mmc/sd cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will lose its power and when powered on again, we
will set signal voltage to 3.3v in mmc_power_up before its resume function
gets called, which will re-init the card.
And for sdio cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will either lose its power or not depending on if it
wants to wakeup the host. If power is not maintained, it is the same case as
mmc/sd cards. If power is maintained, mmc_power_up will not be called and
the card's signal voltage will remain at the last setting.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host has different current capabilities at different voltages, we need
to record these settings seperately. The defined voltages are 1.8/3.0/3.3.
For other voltages, we do not touch current limit setting.
Before we set the current limit for the sd card, find out the host's
operating voltage first and then find out the current capabilities of
the host at that voltage to set the current limit.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When debugging one bad issue, got lots of pr_warning messages
"queuing unknown CIS tuple" which caused a printk storm and
flooded the console.
This patch changes the pr_warning to use pr_warn_ratelimited.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In mmc_read_switch, just do a one time mode 0 switch command to get the
support bits information, no need to do multiple times as the support
bits do not change with different arguments.
And no need to check current limit support bits, as these bits are
fixed according to the signal voltage. If the signal voltage is 1.8V,
the support bits would be 0xf and if the signal voltage is 3.3V, the
support bits would be 0x01. We will check host's ability to set the
current limit.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The effect of the existing code is that we continue blindly when we
should warn about an invalid allocation unit.
Reported-by: dcb314@hotmail.com
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44061
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
max_current_caps can return 0 if not available from the sd controller.
If no regulator is present or the regulator specifies a current
less then 200ma, we no longer still set the 200mA caps bit anyway.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron_lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently mmc host drivers have to decide whether to enable card
detection before calling mmc_add_host() -- in which case a card
insertion event can arrive before the host has been completely
initialised -- or after mmc_add_host(), in which case the initial
card detection can be problematic.
This patch adds an explicit indication of when card detection should
not be carried out. With it in place enabling card detection before
calling mmc_add_host() should be safe. Similarly, disabling it again
after calling mmc_remove_host() will avoid any races.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Card Write-Protect pin is often implemented, using a GPIO, which makes
it simple to provide a generic handler for it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This prepares for the addition of further slot functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A simple extension of mmc slot functions add support for CD GPIO polling
for cases where the GPIO cannot produce interrupts, or where this is not
desired for some reason.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
struct mmc_host::hotplug is becoming a generic hook for slot functions.
Rename it accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a function to get regulators, supplying card's Vdd and Vccq on a
specific host. If a Vdd supplying regulator is found, the function checks,
whether a valid OCR mask can be obtained from it. The Vccq regulator is
optional. A failure to get it is not fatal.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The regulator API functions we're wrapping are exported as GPL, so our
wrappers for the same functions should be too.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_execute_hpi should send the HPI command only once, and only
if the card is in PRG state.
According to eMMC spec, the command's completion time is
not dependent on OUT_OF_INTERRUPT_TIME. Only the transition
out of PRG STATE is guarded by OUT_OF_INTERRUPT_TIME - which
is defined to begin at the end of sending the command itself.
Specify the default timeout for the actual sending of HPI
command, and then use OUT_OF_INTERRUPT_TIME to wait for
the transition out of PRG state.
Reported-by: Alex Lemberg <Alex.Lemberg@sandisk.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix a boot regression on Mackerel boards with sh_mobile_sdhi
in existing kernels causing:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq XXX
caused by 1c6c6952 (genirq: Reject bogus threaded irq requests).
This is backported from Guennadi's patch:
"mmc: extend and rename cd-gpio helpers to handle more slot GPIO functions"
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 3d93576e(skip card initialization if
power class selection fails).
Problem has been reported when this is used with eMMC4.41
card with Tegra Platform. Till the issue is root caused,
bus width selection failure should not be treated as fatal.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-Off-by: Venkatraman S <svenkatr@ti.com>
CC: Ulf Hansson <ulf.hansson@stericsson.com>
CC: Subhash Jadavani <subhashj@codeaurora.org>
CC: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When mmc_host is not spi mode, mmc/sd is doing mmc_deselect_cards().
mmc_deselect_cards could be returned error.
If returned error, we can know something wrong when enter suspend.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width
setting as below:
00b: 1-bit bus
01b: Reserved
10b: 4-bit bus
11b: 8-bit bus (only for embedded SDIO)
And sdio_enable_wide is for setting data bus width as 4-bit.
But currently, it first reads the register, second OR' 1b with
SDIO_CCCR_IF[1], and then writes it back.
As we can see, this is based on such assumption that the
SDIO_CCCR_IF[0] is always 0. Apparently, this is not right.
Signed-off-by: Yong Ding <yongd@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for large sector size of 4KB by disabling
emulation. This patch passes eMMC DATA_SECTOR_SIZE as the logical
block size during mmc_blk_alloc_req.
In order to use this patch for 4KB sector size, ensure that
USE_NATIVE_SECTOR is enabled, partition table is 4KB sector size
aligned and file system block and sector size are 4KB multiples.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
bus_width is passed to the function and when 0 (MMC_BUS_WIDTH_1)
will cause the function to return. So in in the second test it
definitely is different from 0, and the third test is redundant.
Signed-off-by: Philippe De Swert <philippedeswert@gmail.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For eMMC cards that has been initialized from a bootloader,
the VCC voltage supply must not be cut in an uncontrolled
manner, without first sending SLEEP or POWEROFF_NOTIFY.
The regulator_init_complete late initcall, may cut the VCC
regulator if it's reference counter is zero. To be able to
prevent the regulator from being cut, mmc_start_host, which
should execute at device init and thus before late init,
calls mmc_power_up. Then the host driver is able to increase
the reference to the regulator.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With current implementation of power class selection,
mmc_select_powerclass() should never fail. So treat any error
returned by this function as serious enough to skip the card
initialization.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adrian Hunter
Roger Tseng
Joe Perches
Stephen Boyd
Stephen Warren
Ulf Hansson
Grégory Soutadé
Linus Walleij
Chuanxiao.Dong
Javier Martinez Canillas
Sascha Hauer
Fu Zhonghui
Tim Kryger
Lukas Czerner
Romain Izard
Johan Rudholm
Alexander Stein
Russell King
Tim Kryger
Seungwon Jeon
Stefan Wahren
Axel Lin
Markus Mayer
Linus Torvalds
Alexander Shiyan
Jaehoon Chung
Bing Zhao
Wolfram Sang
Dong Aisheng
Rafael J. Wysocki
Greg Kroah-Hartman
Jackey Shen
Grant Grundler
Haijun Zhang
Laurent Pinchart
Minjian Wu
Wei WANG
Mark Brown
Yuvaraj Kumar C D
Simon Baatz
Fredrik Soderstedt
Maya Erez
Akinobu Mita
Li Fei
Philip Rakity
Sergey Yanovich
Aaron Lu
Kevin Liu
Bernie Thompson
Tejun Heo
Guennadi Liakhovetski
Marek Szyprowski
Johan Rudholm
Balaji T K
Konstantin Dorfman
Shawn Guo
Subhash Jadavani
Sujit Reddy Thumma
Kees Cook
Al Cooper
Sachin Kamat
Rafael J. Wysocki
Loic Pallardy
Lee Jones
Kyoungil Kim
Trey Ramsay
Chris Ball
Thierry Reding
Kyungsik Lee
Venkatraman S
Masanari Iida
Aaron Lu
Liu Chuansheng
Alan Cox
Philip Rakity
Yong Ding
Saugata Das
Philippe De Swert