The fsmc_nand driver uses cpu to read/write onto the device. This is inefficient
because of two reasons
- the cpu gets locked on AHB bus while reading from NAND
- the cpu is unnecessarily used when dma can do the job
This patch adds the support for accessing the device through DMA
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The default way of accessing nand device is using the nand width. This means
that 8bit devices are using u8 * and 16bit devices are accessed using u16 *.
This results in a non-optimal performance since the FSMC is designed to
translate the normal word accesses into device width based accesses. This patch
implements read_buf and write_buf callbacks using word by word accesses.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
FSMC controllers provide registers to program the required timing values for
attached NAND device. The timing values used until now are relaxed and should
work for all devices.
Although, for read/write performance improvements, the fsmc nand driver should
accept nand timings as a platform data and program the timing parameters into
fsmc registers accordingly.
This patch implements this modification. Additionally, it programs the default
timing parameters if these are not passed via platform data.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds 'ecc_strength' to struct mtd_info. This stores the maximum number of
bit errors that can be corrected in one writesize region.
For consistency with the nand code, 'strength' is similiarly added to struct
nand_ecc_ctrl. This stores the maximum number of bit errors that can be
corrected in one ecc step.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adds power management code with fine granularity. Every flash control
command is enclosed by runtime_put()/get()s. To make sure that no
overhead is generated by too frequent power state switches, a quality of
service request is issued.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Address Latch Enable (ALE) and Command Latch Enable (CLE) defines are
platform specific and were wrongly put in driver specific fsmc.h file.
Move such defines to their respective platform.
Also instead of relying on fsmc driver, pass ALE, CLE offsets explicitly
from individual platform.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ALE and CLE offsets can be different on different devices. Let devices
pass these offsets to the fsmc driver through platform data.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a register used in new FLCTL hardware and a feature flag for it.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of reading out the register, use a cached value. This will
make way for a proper runtime power management implementation.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for a new hardware generation. The meaning of some bits
of the FLCMNCR register changed, so some new defines are added
parallel to the existing ones to keep backward compatibility.
The defines allow to choose an appropriate clocking scheme.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move the header to a more common place.
The mxs dma engine is not only used in mx23/mx28, but also used
in mx50/mx6q. It will also be used in the future chips.
Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to
store the Freescale's header files.
change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver
to the new header file.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch changes all the OTP functions like 'mtd_get_fact_prot_info()' and
makes them return zero immediately if the input 'len' parameter is 0. This is
not really needed currently, but most of the other functions do this, and it is
just consistent to do the same in the OTP functions.
This patch also moves the OTP functions from the header file to mtdcore.c
because they become a bit too big for being inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.
And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add verification of the offset and length to MTD API functions and verify that
MTD device offset and length are within MTD device size.
The modified API functions are:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch also uninlines these functions and exports in mtdcore.c because they
are not performance-critical and do not have to be inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.
Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* bootloader cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The description for badblockbits is incorrect. I think someone just made
up a false description on the spot to satisfy some kerneldoc warning.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Because it is useless to call it if the device is opened in R/O mode, and also
harmful: on CFI NOR flash it may block for long time waiting for erase
operations to complete is another partition with a R/W file-system on this
chip.
Artem Bityutskiy: write commit message, amend the patch to match the latest
tree (we use mtd_sync(), not mtd->sync() nowadays).
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The struct is duplicated, plus causes the following flood:
CC drivers/power/ab8500_fg.o
ab8500_fg.c: In function ‘ab8500_fg_get_ext_psy_data’:
b8500_fg.c:2081:8: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The struct is duplicated, plus when used it causes the following
warnings:
CHECK drivers/power/ab8500_fg.c
ab8500_fg.c:818:13: warning: incorrect type in assignment (different base types)
ab8500_fg.c:818:13: expected struct v_to_cap *tbl
ab8500_fg.c:818:13: got struct abx500_v_to_cap *const v_to_cap_tbl
CC drivers/power/ab8500_fg.o
ab8500_fg.c: In function 'ab8500_fg_volt_to_capacity':
ab8500_fg.c:818:6: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This is the same as abx500_adc_therm, but when the former is used,
the following warning flood pops up:
drivers/power/ab8500_btemp.c: In function 'ab8500_btemp_batctrl_volt_to_res':
ab8500_btemp.c:150:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_curr_source_enable':
ab8500_btemp.c:212:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c:244:32: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_measure_temp':
ab8500_btemp.c:462:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c: In function 'ab8500_btemp_id':
ab8500_btemp.c:528:121: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
ab8500_btemp.c:551:25: warning: comparison between 'enum abx500_adc_therm' and 'enum adc_therm' [-Wenum-compare]
This patch fixes the issue by switching the driver to use more
namespace-friendly enum.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This driver is responsible for detecting the ac/usb plugin and also includes
function to enable ac/usb charging and re-kick the watchdog.
It registers with the power supply class and provides information to the user
space. The information include status of ac/usb charger device.
This information in turn will be used by the abx500 charging algorithm driver
to enable/disable and monitor charging.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This is a charging algorithm driver for abx500 variants. It is the central
entity for battery driver and is responsible for charging and monitoring
the battery driver. It is a hardware independant driver and also monitors
other abx500 power supply devices.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Driver support for the Summit I²C battery charger. This is used in some
Intel devices.
Signed-off-by: Bruce E. Robertson <bruce.e.robertson@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add brief description of lp8727_platform_data and lp8727_chg_param.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add 'Texas Instruments' because TI acquired National semiconductor at 2011.
And the driver information is added in the header file.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add power on reset (POR) init procedure defined by the maxim
appnote. Using this procedure ensures that the part is
configured/initialized correctly at POR and improves early accuracy of
the fuel gauge and informs the fuel gauge with the battery
characterization parameters. The battery characterization parameters
come from the maxim characterization procedure.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The daemon takes a versioned binary struct. Hopefully this should allow
us to revise the struct later if it becomes necessary.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Dummy functions for the newly added cpu access ops need variable names for
arguments.
Also, the introduction of flags in dma_buf_fd needs to be added to dummy
functions as well.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Big differences to other contenders in the field (like ion) is
that this also supports highmem, so we have to split up the cpu
access from the kernel side into a prepare and a kmap step.
Prepare is allowed to fail and should do everything required so that
the kmap calls can succeed (like swapin/backing storage allocation,
flushing, ...).
More in-depth explanations will follow in the follow-up documentation
patch.
Changes in v2:
- Clear up begin_cpu_access confusion noticed by Sumit Semwal.
- Don't automatically fallback from the _atomic variants to the
non-atomic variants. The _atomic callbacks are not allowed to
sleep, so we want exporters to make this decision explicit. The
function signatures are explicit, so simpler exporters can still
use the same function for both.
- Make the unmap functions optional. Simpler exporters with permanent
mappings don't need to do anything at unmap time.
Changes in v3:
- Adjust the WARN_ON checks for the new ->ops functions as suggested
by Rob Clark and Sumit Semwal.
- Rebased on top of latest dma-buf-next git.
Changes in v4:
- Fixup a missing - in a return -EINVAL; statement.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
The mutex protects the attachment list and hence needs to be held
around the callbakc to the exporters (optional) attach/detach
functions.
Holding the mutex around the map/unmap calls doesn't protect any
dma_buf state. Exporters need to properly protect any of their own
state anyway (to protect against calls from their own interfaces).
So this only makes the locking messier (and lockdep easier to anger).
Therefore let's just drop this.
v2: Rebased on top of latest dma-buf-next git.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Works in a similar way to get_file(), and is needed in cases such as
when the exporter needs to also keep a reference to the dmabuf (that
is later released with a dma_buf_put()), and possibly other similar
cases.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
We need to pass the flags into dma_buf_fd at this point,
so the flags end up doing the right thing for O_CLOEXEC.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Some exporters may use DMA map/unmap APIs in dma-buf ops, which require
enum dma_data_direction for both map and unmap operations.
Thus, the unmap dma_buf_op also needs to have enum dma_data_direction as
a parameter.
Reported-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
This patch adds a set of macros that can be used to declare
kernel parameters to be parsed _before_ initcalls at a chosen
level are executed. We rename the now-unused "flags" field of
struct kernel_param as the level. It's signed, for when we
use this for early params as well, in future.
Linker macro collating init calls had to be modified in order
to add additional symbols between levels that are later used
by the init code to split the calls into blocks.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
This eliminates that code (though leaves the flags field in the struct,
for impending use).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Support of PCI mode for the dw_mmc driver. This Patch adds the
support for the scenario where the Synopsys Designware IP
is present on the PCI bus. The patch adds the minimal modifications
necessary for the driver to work on PCI platform. Also added separate
files for PCI and PLATFORM modes of operation.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The only users of ARCH_HAS_DMA_SET_COHERENT_MASK are 2 ARM platforms:
ixp4xx and pxa cm_x2xx. We've been getting lucky that the define is
implicitly included before dma-mapping.h, but the removal of io.h broke
things (c334bc1 ARM: make mach/io.h include optional). Since memory.h
is the correct place, but no longer exists, convert the define to a
kconfig entry.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
skb_add_rx_frag() API is misleading.
Network skbs built with this helper can use uncharged kernel memory and
eventually stress/crash machine in OOM.
Add a 'truesize' parameter and then fix drivers in followup patches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Add fast-EOI acking of interrupts (clear a bit instead of hypercall)
And bug-fixes:
* Fix CPU bring-up code missing a call to notify other subsystems.
* Fix reading /sys/hypervisor even if PVonHVM drivers are not loaded.
* In Xen ACPI processor driver: remove too verbose WARN messages, fix up
the Kconfig dependency to be a module by default, and add dependency on
CPU_FREQ.
* Disable CPU frequency drivers from loading when booting under Xen
(as we want the Xen ACPI processor to be used instead).
* Cleanups in tmem code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPbc3DAAoJEFjIrFwIi8fJTQkIAMnH2fPhcHAb4mNaz+3gdmsZ
Flo6V1gMBcO8xKZlUkFgKKPYoOm7lLmvoceXLVSH5oOKSnSJo1zSinzKmcdJQo/D
kPo4/EguNwtzcAcQh2dmT6/IM9O3ihMKUli7Oajif9PLCFFFqTaG3Y3YNBo/rxTY
D3HAnJrIfmIyG0NpLnaFCWhCzUvcB4M7ysutECqcF8l5gnbHxRVeCKD0blM+n9GH
Wyum00dQCwo6h6wTduhPOAxHAM4rncyR3heOB2vDxq9YJHSUhhcva5QCgQ+tdUVt
6U2TQT1L2Px8iXXzr2w9YBpepOVajZReoKhajLjJ5VbkpBZFz5dVNfJ8LpF8RV8=
=z8IB
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull more xen updates from Konrad Rzeszutek Wilk:
"One tiny feature that accidentally got lost in the initial git pull:
* Add fast-EOI acking of interrupts (clear a bit instead of
hypercall)
And bug-fixes:
* Fix CPU bring-up code missing a call to notify other subsystems.
* Fix reading /sys/hypervisor even if PVonHVM drivers are not loaded.
* In Xen ACPI processor driver: remove too verbose WARN messages, fix
up the Kconfig dependency to be a module by default, and add
dependency on CPU_FREQ.
* Disable CPU frequency drivers from loading when booting under Xen
(as we want the Xen ACPI processor to be used instead).
* Cleanups in tmem code."
* tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: Fix Kconfig dependency on CPU_FREQ
xen: initialize platform-pci even if xen_emul_unplug=never
xen/smp: Fix bringup bug in AP code.
xen/acpi: Remove the WARN's as they just create noise.
xen/tmem: cleanup
xen: support pirq_eoi_map
xen/acpi-processor: Do not depend on CPU frequency scaling drivers.
xen/cpufreq: Disable the cpu frequency scaling drivers from loading.
provide disable_cpufreq() function to disable the API.
This was part of the for-next branch earlier but for some reasons
a rebuild of the tree missed it, so I'm putting it back in now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
https://lkml.org/lkml/2012/3/4/159
--
Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then
one to delete the device.h includes from the linux/include/ dir
wherever possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3j4+
-----END PGP SIGNATURE-----
Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/device.h> avoidance patches from Paul Gortmaker:
"Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then one
to delete the device.h includes from the linux/include/ dir wherever
possible."
* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
device.h: audit and cleanup users in main include dir
device.h: cleanup users outside of linux/include (C files)
"[RFC - PATCH 0/7] consolidation of BUG support code."
https://lkml.org/lkml/2012/1/26/525
--
The changes shown here are to unify linux's BUG support under
the one <linux/bug.h> file. Due to historical reasons, we have
some BUG code in bug.h and some in kernel.h -- i.e. the support for
BUILD_BUG in linux/kernel.h predates the addition of linux/bug.h,
but old code in kernel.h wasn't moved to bug.h at that time. As
a band-aid, kernel.h was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions.
Here is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.]
Ugh - very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and
hence relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2.
But to ensure that git history for bisect doesn't get needless
build failures introduced, the commits have been reorderd to fix
the problem areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PYQT
-----END PGP SIGNATURE-----
Merge tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/bug.h> cleanup from Paul Gortmaker:
"The changes shown here are to unify linux's BUG support under the one
<linux/bug.h> file. Due to historical reasons, we have some BUG code
in bug.h and some in kernel.h -- i.e. the support for BUILD_BUG in
linux/kernel.h predates the addition of linux/bug.h, but old code in
kernel.h wasn't moved to bug.h at that time. As a band-aid, kernel.h
was including <asm/bug.h> to pseudo link them.
This has caused confusion[1] and general yuck/WTF[2] reactions. Here
is an example that violates the principle of least surprise:
CC lib/string.o
lib/string.c: In function 'strlcat':
lib/string.c:225:2: error: implicit declaration of function 'BUILD_BUG_ON'
make[2]: *** [lib/string.o] Error 1
$
$ grep linux/bug.h lib/string.c
#include <linux/bug.h>
$
We've included <linux/bug.h> for the BUG infrastructure and yet we
still get a compile fail! [We've not kernel.h for BUILD_BUG_ON.] Ugh -
very confusing for someone who is new to kernel development.
With the above in mind, the goals of this changeset are:
1) find and fix any include/*.h files that were relying on the
implicit presence of BUG code.
2) find and fix any C files that were consuming kernel.h and hence
relying on implicitly getting some/all BUG code.
3) Move the BUG related code living in kernel.h to <linux/bug.h>
4) remove the asm/bug.h from kernel.h to finally break the chain.
During development, the order was more like 3-4, build-test, 1-2. But
to ensure that git history for bisect doesn't get needless build
failures introduced, the commits have been reorderd to fix the problem
areas in advance.
[1] https://lkml.org/lkml/2012/1/3/90
[2] https://lkml.org/lkml/2012/1/17/414"
Fix up conflicts (new radeon file, reiserfs header cleanups) as per Paul
and linux-next.
* tag 'bug-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
kernel.h: doesn't explicitly use bug.h, so don't include it.
bug: consolidate BUILD_BUG_ON with other bug code
BUG: headers with BUG/BUG_ON etc. need linux/bug.h
bug.h: add include of it to various implicit C users
lib: fix implicit users of kernel.h for TAINT_WARN
spinlock: macroize assert_spin_locked to avoid bug.h dependency
x86: relocate get/set debugreg fcns to include/asm/debugreg.
The pxa regulator branch removes the bq24022 driver, while a lot of
other regulator drivers got added in the regulator tree. This
resolves the trivial conflicts by merging in the regulator patches
that are already merged into v3.4.
Conflicts:
drivers/regulator/Kconfig
drivers/regulator/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull sysctl updates from Eric Biederman:
- Rewrite of sysctl for speed and clarity.
Insert/remove/Lookup in sysctl are all now O(NlogN) operations, and
are no longer bottlenecks in the process of adding and removing
network devices.
sysctl is now focused on being a filesystem instead of system call
and the code can all be found in fs/proc/proc_sysctl.c. Hopefully
this means the code is now approachable.
Much thanks is owed to Lucian Grinjincu for keeping at this until
something was found that was usable.
- The recent proc_sys_poll oops found by the fuzzer during hibernation
is fixed.
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl: (36 commits)
sysctl: protect poll() in entries that may go away
sysctl: Don't call sysctl_follow_link unless we are a link.
sysctl: Comments to make the code clearer.
sysctl: Correct error return from get_subdir
sysctl: An easier to read version of find_subdir
sysctl: fix memset parameters in setup_sysctl_set()
sysctl: remove an unused variable
sysctl: Add register_sysctl for normal sysctl users
sysctl: Index sysctl directories with rbtrees.
sysctl: Make the header lists per directory.
sysctl: Move sysctl_check_dups into insert_header
sysctl: Modify __register_sysctl_paths to take a set instead of a root and an nsproxy
sysctl: Replace root_list with links between sysctl_table_sets.
sysctl: Add sysctl_print_dir and use it in get_subdir
sysctl: Stop requiring explicit management of sysctl directories
sysctl: Add a root pointer to ctl_table_set
sysctl: Rewrite proc_sys_readdir in terms of first_entry and next_entry
sysctl: Rewrite proc_sys_lookup introducing find_entry and lookup_entry.
sysctl: Normalize the root_table data structure.
sysctl: Factor out insert_header and erase_header
...
Pull cpufreq updates for 3.4 from Dave Jones: new drivers and some fixes.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
provide disable_cpufreq() function to disable the API.
EXYNOS5250: Add support cpufreq for EXYNOS5250
EXYNOS4X12: Add support cpufreq for EXYNOS4X12
[CPUFREQ] CPUfreq ondemand: update sampling rate without waiting for next sampling
[CPUFREQ] Add S3C2416/S3C2450 cpufreq driver
[CPUFREQ] Fix exposure of ARM_EXYNOS4210_CPUFREQ
[CPUFREQ] EXYNOS4210: update the name of EXYNOS clock register
[CPUFREQ] EXYNOS: Initialize locking_frequency with initial frequency
[CPUFREQ] s3c64xx: Fix mis-cherry pick of VDDINT
Fix up trivial conflicts in Kconfig and Makefile due to just changes
next to each other (OMAP2PLUS changes vs some new EXYNOS cpufreq
drivers).
Pull #2 ARM updates from Russell King:
"Further ARM AMBA primecell updates which aren't included directly in
the previous commit. I wanted to keep these separate as they're
touching stuff outside arch/arm/."
* 'amba' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driver
ARM: 7335/1: mach-u300: do away with MMC config files
ARM: 7280/1: mmc: mmci: Cache MMCICLOCK and MMCIPOWER register
ARM: 7309/1: realview: fix unconnected interrupts on EB11MP
ARM: 7230/1: mmc: mmci: Fix PIO read for small SDIO packets
ARM: 7227/1: mmc: mmci: Prepare for SDIO before setting up DMA job
ARM: 7223/1: mmc: mmci: Fixup use of runtime PM and use autosuspend
ARM: 7221/1: mmc: mmci: Change from using legacy suspend
ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handler
ARM: 7218/1: mmc: mmci: Provide option to configure bus signal direction
ARM: 7217/1: mmc: mmci: Put power register deviations in variant data
ARM: 7216/1: mmc: mmci: Do not release spinlock in request_end
ARM: 7215/1: mmc: mmci: Increase max_segs from 16 to 128
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
Merge second batch of patches from Andrew Morton:
- various misc things
- core kernel changes to prctl, exit, exec, init, etc.
- kernel/watchdog.c updates
- get_maintainer
- MAINTAINERS
- the backlight driver queue
- core bitops code cleanups
- the led driver queue
- some core prio_tree work
- checkpatch udpates
- largeish crc32 update
- a new poll() feature for the v4l guys
- the rtc driver queue
- fatfs
- ptrace
- signals
- kmod/usermodehelper updates
- coredump
- procfs updates
* emailed from Andrew Morton <akpm@linux-foundation.org>: (141 commits)
seq_file: add seq_set_overflow(), seq_overflow()
proc-ns: use d_set_d_op() API to set dentry ops in proc_ns_instantiate().
procfs: speed up /proc/pid/stat, statm
procfs: add num_to_str() to speed up /proc/stat
proc: speed up /proc/stat handling
fs/proc/kcore.c: make get_sparsemem_vmemmap_info() static
coredump: add VM_NODUMP, MADV_NODUMP, MADV_CLEAR_NODUMP
coredump: remove VM_ALWAYSDUMP flag
kmod: make __request_module() killable
kmod: introduce call_modprobe() helper
usermodehelper: ____call_usermodehelper() doesn't need do_exit()
usermodehelper: kill umh_wait, renumber UMH_* constants
usermodehelper: implement UMH_KILLABLE
usermodehelper: introduce umh_complete(sub_info)
usermodehelper: use UMH_WAIT_PROC consistently
signal: zap_pid_ns_processes: s/SEND_SIG_NOINFO/SEND_SIG_FORCED/
signal: oom_kill_task: use SEND_SIG_FORCED instead of force_sig()
signal: cosmetic, s/from_ancestor_ns/force/ in prepare_signal() paths
signal: give SEND_SIG_FORCED more power to beat SIGNAL_UNKILLABLE
Hexagon: use set_current_blocked() and block_sigmask()
...
Process accounting applications as top, ps visit some files under
/proc/<pid>. With seq_put_decimal_ull(), we can optimize /proc/<pid>/stat
and /proc/<pid>/statm files.
This patch adds
- seq_put_decimal_ll() for signed values.
- allow delimiter == 0.
- convert seq_printf() to seq_put_decimal_ull/ll in /proc/stat, statm.
Test result on a system with 2000+ procs.
Before patch:
[kamezawa@bluextal test]$ top -b -n 1 | wc -l
2223
[kamezawa@bluextal test]$ time top -b -n 1 > /dev/null
real 0m0.675s
user 0m0.044s
sys 0m0.121s
[kamezawa@bluextal test]$ time ps -elf > /dev/null
real 0m0.236s
user 0m0.056s
sys 0m0.176s
After patch:
kamezawa@bluextal ~]$ time top -b -n 1 > /dev/null
real 0m0.657s
user 0m0.052s
sys 0m0.100s
[kamezawa@bluextal ~]$ time ps -elf > /dev/null
real 0m0.198s
user 0m0.050s
sys 0m0.145s
Considering top, ps tend to scan /proc periodically, this will reduce cpu
consumption by top/ps to some extent.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
== stat_check.py
num = 0
with open("/proc/stat") as f:
while num < 1000 :
data = f.read()
f.seek(0, 0)
num = num + 1
==
perf shows
20.39% stat_check.py [kernel.kallsyms] [k] format_decode
13.41% stat_check.py [kernel.kallsyms] [k] number
12.61% stat_check.py [kernel.kallsyms] [k] vsnprintf
10.85% stat_check.py [kernel.kallsyms] [k] memcpy
4.85% stat_check.py [kernel.kallsyms] [k] radix_tree_lookup
4.43% stat_check.py [kernel.kallsyms] [k] seq_printf
This patch removes most of calls to vsnprintf() by adding num_to_str()
and seq_print_decimal_ull(), which prints decimal numbers without rich
functions provided by printf().
On my 8cpu box.
== Before patch ==
[root@bluextal test]# time ./stat_check.py
real 0m0.150s
user 0m0.026s
sys 0m0.121s
== After patch ==
[root@bluextal test]# time ./stat_check.py
real 0m0.055s
user 0m0.022s
sys 0m0.030s
[akpm@linux-foundation.org: remove incorrect comment, use less statck in num_to_str(), move comment from .h to .c, simplify seq_put_decimal_ull()]
[andrea@betterlinux.com: avoid breaking the ABI in /proc/stat]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrea Righi <andrea@betterlinux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Turner <pjt@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we no longer need the VM_ALWAYSDUMP flag, let's use the freed bit
for 'VM_NODUMP' flag. The idea is is to add a new madvise() flag:
MADV_DONTDUMP, which can be set by applications to specifically request
memory regions which should not dump core.
The specific application I have in mind is qemu: we can add a flag there
that wouldn't dump all of guest memory when qemu dumps core. This flag
might also be useful for security sensitive apps that want to absolutely
make sure that parts of memory are not dumped. To clear the flag use:
MADV_DODUMP.
[akpm@linux-foundation.org: s/MADV_NODUMP/MADV_DONTDUMP/, s/MADV_CLEAR_NODUMP/MADV_DODUMP/, per Roland]
[akpm@linux-foundation.org: fix up the architectures which broke]
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The motivation for this patchset was that I was looking at a way for a
qemu-kvm process, to exclude the guest memory from its core dump, which
can be quite large. There are already a number of filter flags in
/proc/<pid>/coredump_filter, however, these allow one to specify 'types'
of kernel memory, not specific address ranges (which is needed in this
case).
Since there are no more vma flags available, the first patch eliminates
the need for the 'VM_ALWAYSDUMP' flag. The flag is used internally by
the kernel to mark vdso and vsyscall pages. However, it is simple
enough to check if a vma covers a vdso or vsyscall page without the need
for this flag.
The second patch then replaces the 'VM_ALWAYSDUMP' flag with a new
'VM_NODUMP' flag, which can be set by userspace using new madvise flags:
'MADV_DONTDUMP', and unset via 'MADV_DODUMP'. The core dump filters
continue to work the same as before unless 'MADV_DONTDUMP' is set on the
region.
The qemu code which implements this features is at:
http://people.redhat.com/~jbaron/qemu-dump/qemu-dump.patch
In my testing the qemu core dump shrunk from 383MB -> 13MB with this
patch.
I also believe that the 'MADV_DONTDUMP' flag might be useful for
security sensitive apps, which might want to select which areas are
dumped.
This patch:
The VM_ALWAYSDUMP flag is currently used by the coredump code to
indicate that a vma is part of a vsyscall or vdso section. However, we
can determine if a vma is in one these sections by checking it against
the gate_vma and checking for a non-NULL return value from
arch_vma_name(). Thus, freeing a valuable vma bit.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes. It is not sane to use UMH_KILLABLE with enum
umh_wait, but obviously we do not want another argument in
call_usermodehelper_* helpers. Kill this enum, use the plain int.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement UMH_KILLABLE, should be used along with UMH_WAIT_EXEC/PROC.
The caller must ensure that subprocess_info->path/etc can not go away
until call_usermodehelper_freeinfo().
call_usermodehelper_exec(UMH_KILLABLE) does
wait_for_completion_killable. If it fails, it uses
xchg(&sub_info->complete, NULL) to serialize with umh_complete() which
does the same xhcg() to access sub_info->complete.
If call_usermodehelper_exec wins, it can safely return. umh_complete()
should get NULL and call call_usermodehelper_freeinfo().
Otherwise we know that umh_complete() was already called, in this case
call_usermodehelper_exec() falls back to wait_for_completion() which
should succeed "very soon".
Note: UMH_NO_WAIT == -1 but it obviously should not be used with
UMH_KILLABLE. We delay the neccessary cleanup to simplify the back
porting.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PTRACE_SEIZE code is tested and ready for production use, remove the
code which requires special bit in data argument to make PTRACE_SEIZE
work.
Strace team prepares for a new release of strace, and we would like to
ship the code which uses PTRACE_SEIZE, preferably after this change goes
into released kernel.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PTRACE_EVENT_foo and PTRACE_O_TRACEfoo used to match.
New PTRACE_EVENT_STOP is the first event which has no corresponding
PTRACE_O_TRACE option. If we will ever want to add another such option,
its PTRACE_EVENT's value will collide with PTRACE_EVENT_STOP's value.
This patch changes PTRACE_EVENT_STOP value to prevent this.
While at it, added a comment - the one atop PTRACE_EVENT block, saying
"Wait extended result codes for the above trace options", is not true
for PTRACE_EVENT_STOP.
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Exchange PT_TRACESYSGOOD and PT_PTRACE_CAP bit positions, which makes
PT_option bits contiguous and therefore makes code in
ptrace_setoptions() much simpler.
Every PTRACE_O_TRACEevent is defined to (1 << PTRACE_EVENT_event)
instead of using explicit numeric constants, to ensure we don't mess up
relationship between bit positions and event ids.
PT_EVENT_FLAG_SHIFT was not particularly useful, PT_OPT_FLAG_SHIFT with
value of PT_EVENT_FLAG_SHIFT-1 is easier to use.
PT_TRACE_MASK constant is nuked, the only its use is replaced by
(PTRACE_O_MASK << PT_OPT_FLAG_SHIFT).
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ptrace_event(PTRACE_EVENT_EXEC) sends SIGTRAP if PT_TRACE_EXEC is not
set. This is because this SIGTRAP predates PTRACE_O_TRACEEXEC option,
we do not need/want this with PT_SEIZED which can set the options during
attach.
Suggested-by: Pedro Alves <palves@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Chris Evans <scarybeasts@gmail.com>
Cc: Indan Zupancic <indan@nul.nu>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another old/known problem. If the tracee is killed after it reports
syscall_entry, it starts the syscall and debugger can't control this.
This confuses the users and this creates the security problems for
ptrace jailers.
Change tracehook_report_syscall_entry() to return non-zero if killed,
this instructs syscall_trace_enter() to abort the syscall.
Reported-by: Chris Evans <scarybeasts@gmail.com>
Tested-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases the poll() implementation in a driver has to do different
things depending on the events the caller wants to poll for. An example
is when a driver needs to start a DMA engine if the caller polls for
POLLIN, but doesn't want to do that if POLLIN is not requested but instead
only POLLOUT or POLLPRI is requested. This is something that can happen
in the video4linux subsystem among others.
Unfortunately, the current epoll/poll/select implementation doesn't
provide that information reliably. The poll_table_struct does have it: it
has a key field with the event mask. But once a poll() call matches one
or more bits of that mask any following poll() calls are passed a NULL
poll_table pointer.
Also, the eventpoll implementation always left the key field at ~0 instead
of using the requested events mask.
This was changed in eventpoll.c so the key field now contains the actual
events that should be polled for as set by the caller.
The solution to the NULL poll_table pointer is to set the qproc field to
NULL in poll_table once poll() matches the events, not the poll_table
pointer itself. That way drivers can obtain the mask through a new
poll_requested_events inline.
The poll_table_struct can still be NULL since some kernel code calls it
internally (netfs_state_poll() in ./drivers/staging/pohmelfs/netfs.h). In
that case poll_requested_events() returns ~0 (i.e. all events).
Very rarely drivers might want to know whether poll_wait will actually
wait. If another earlier file descriptor in the set already matched the
events the caller wanted to wait for, then the kernel will return from the
select() call without waiting. This might be useful information in order
to avoid doing expensive work.
A new helper function poll_does_not_wait() is added that drivers can use
to detect this situation. This is now used in sock_poll_wait() in
include/net/sock.h. This was the only place in the kernel that needed
this information.
Drivers should no longer access any of the poll_table internals, but use
the poll_requested_events() and poll_does_not_wait() access functions
instead. In order to enforce that the poll_table fields are now prepended
with an underscore and a comment was added warning against using them
directly.
This required a change in unix_dgram_poll() in unix/af_unix.c which used
the key field to get the requested events. It's been replaced by a call
to poll_requested_events().
For qproc it was especially important to change its name since the
behavior of that field changes with this patch since this function pointer
can now be NULL when that wasn't possible in the past.
Any driver accessing the qproc or key fields directly will now fail to compile.
Some notes regarding the correctness of this patch: the driver's poll()
function is called with a 'struct poll_table_struct *wait' argument. This
pointer may or may not be NULL, drivers can never rely on it being one or
the other as that depends on whether or not an earlier file descriptor in
the select()'s fdset matched the requested events.
There are only three things a driver can do with the wait argument:
1) obtain the key field:
events = wait ? wait->key : ~0;
This will still work although it should be replaced with the new
poll_requested_events() function (which does exactly the same).
This will now even work better, since wait is no longer set to NULL
unnecessarily.
2) use the qproc callback. This could be deadly since qproc can now be
NULL. Renaming qproc should prevent this from happening. There are no
kernel drivers that actually access this callback directly, BTW.
3) test whether wait == NULL to determine whether poll would return without
waiting. This is no longer sufficient as the correct test is now
wait == NULL || wait->_qproc == NULL.
However, the worst that can happen here is a slight performance hit in
the case where wait != NULL and wait->_qproc == NULL. In that case the
driver will assume that poll_wait() will actually add the fd to the set
of waiting file descriptors. Of course, poll_wait() will not do that
since it tests for wait->_qproc. This will not break anything, though.
There is only one place in the whole kernel where this happens
(sock_poll_wait() in include/net/sock.h) and that code will be replaced
by a call to poll_does_not_wait() in the next patch.
Note that even if wait->_qproc != NULL drivers cannot rely on poll_wait()
actually waiting. The next file descriptor from the set might match the
event mask and thus any possible waits will never happen.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reuse the existing crc32 code to stamp out a crc32c implementation.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Bob Pearson <rpearson@systemfabricworks.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's equivalent to __printf, so prefer __scanf.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* add 'struct lm3530_pwm_data' in the platform data
The pwm data is the platform specific functions which generate the pwm.
The pwm data is only valid when brightness is pwm input mode.
Functions should be implemented by the pwm driver.
pwm_set_intensity() : set duty of pwm.
pwm_get_intensity() : get current the brightness.
* brightness control by pwm
If the control mode is pwm, then brightness is changed by the duty of
pwm=. So pwm platform function should be called in lm3530_brightness_set().
* do not update brightness register when pwm input mode
In pwm input mode, brightness register is not used.
If any value is updated in this register, then the led will be off.
* when input mode is changed, set duty of pwm to 0 if unnecessary.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lp5521 has autonomous operation mode without external control.
Using lp5521_platform_data, various led patterns can be configurable.
For supporting this feature, new functions and device attribute are
added.
Structure of lp5521_led_pattern: 3 channels are supported - red, green
and blue. Pattern(s) of each channel and numbers of pattern(s) are
defined in the pla= tform data. Pattern data are hexa codes which
include pattern commands such like set pwm, wait, ramp up/down, branch
and so on.
Pattern mode functions:
* lp5521_clear_program_memory
Before running new led pattern, program memory should be cleared.
* lp5521_write_program_memory
Pattern data updated in the program memory via the i2c.
* lp5521_get_pattern
Get pattern from predefined in the platform data.
* lp5521_run_led_pattern
Stop current pattern or run new pattern.
Transition time is required between different operation mode.
Device attribute - 'led_pattern': To load specific led pattern, new device
attribute is added.
When the lp5521 driver is unloaded, stop current led pattern mode.
Documentation updated : description about how to define the led patterns
and example.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The value of CONFIG register(Addr 08h) is configurable. For supporting
this feature, update_config is added in the platform data. If
'update_config' is not defined, the default value is 'LP5521_PWRSAVE_EN |
LP5521_CP_MODE_AUTO | LP5521_R_TO_BATT'.
To define CONFIG register in the platform data, the bit definitions were
mo= ved to the header file.
Documentation updated : description about 'update_config' and example.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of each led channel can be configurable. For the compatibility,
the name is set to default value(xx:channelN) when 'name' is not defined.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arun MURTHY <arun.murthy@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce for_each_clear_bit() and for_each_clear_bit_from(). They are
similar to for_each_set_bit() and list_for_each_set_bit_from(), but they
iterate over all the cleared bits in a memory region.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stefano Panella <stefano.panella@csr.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove for_each_set_bit_cont() after confirming that no one uses
for_each_set_bit_cont() anymore.
[sfr@canb.auug.org.au: regmap: cope with bitops API change]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This renames for_each_set_bit_cont() to for_each_set_bit_from() because
it is analogous to list_for_each_entry_from() in list.h rather than
list_for_each_entry_continue().
This doesn't remove for_each_set_bit_cont() for now.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
THis driver supports TI LP8550/LP8551/LP8552/LP8553/LP8556 backlight
devices.
The brightness can be controlled by the I2C or PWM input. The lp855x
driver provides both modes. For the PWM control, pwm-specific functions
can be defined in the platform data. And some information can be read
via the sysfs(lp855x device attributes).
For details, please refer to Documentation/backlight/lp855x-driver.txt.
[axel.lin@gmail.com: add missing mutex_unlock in lp855x_read_byte() error path]
[axel.lin@gmail.com: check platform data in lp855x_probe()]
[axel.lin@gmail.com: small cleanups]
[dan.carpenter@oracle.com: silence a compiler warning]
[axel.lin@gmail.com: use id->driver_data to differentiate lp855x chips]
[akpm@linux-foundation.org: simplify boolean return expression]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Userspace service managers/supervisors need to track their started
services. Many services daemonize by double-forking and get implicitly
re-parented to PID 1. The service manager will no longer be able to
receive the SIGCHLD signals for them, and is no longer in charge of
reaping the children with wait(). All information about the children is
lost at the moment PID 1 cleans up the re-parented processes.
With this prctl, a service manager process can mark itself as a sort of
'sub-init', able to stay as the parent for all orphaned processes
created by the started services. All SIGCHLD signals will be delivered
to the service manager.
Receiving SIGCHLD and doing wait() is in cases of a service-manager much
preferred over any possible asynchronous notification about specific
PIDs, because the service manager has full access to the child process
data in /proc and the PID can not be re-used until the wait(), the
service-manager itself is in charge of, has happened.
As a side effect, the relevant parent PID information does not get lost
by a double-fork, which results in a more elaborate process tree and
'ps' output:
before:
# ps afx
253 ? Ss 0:00 /bin/dbus-daemon --system --nofork
294 ? Sl 0:00 /usr/libexec/polkit-1/polkitd
328 ? S 0:00 /usr/sbin/modem-manager
608 ? Sl 0:00 /usr/libexec/colord
658 ? Sl 0:00 /usr/libexec/upowerd
819 ? Sl 0:00 /usr/libexec/imsettings-daemon
916 ? Sl 0:00 /usr/libexec/udisks-daemon
917 ? S 0:00 \_ udisks-daemon: not polling any devices
after:
# ps afx
294 ? Ss 0:00 /bin/dbus-daemon --system --nofork
426 ? Sl 0:00 \_ /usr/libexec/polkit-1/polkitd
449 ? S 0:00 \_ /usr/sbin/modem-manager
635 ? Sl 0:00 \_ /usr/libexec/colord
705 ? Sl 0:00 \_ /usr/libexec/upowerd
959 ? Sl 0:00 \_ /usr/libexec/udisks-daemon
960 ? S 0:00 | \_ udisks-daemon: not polling any devices
977 ? Sl 0:00 \_ /usr/libexec/packagekitd
This prctl is orthogonal to PID namespaces. PID namespaces are isolated
from each other, while a service management process usually requires the
services to live in the same namespace, to be able to talk to each
other.
Users of this will be the systemd per-user instance, which provides
init-like functionality for the user's login session and D-Bus, which
activates bus services on-demand. Both need init-like capabilities to
be able to properly keep track of the services they start.
Many thanks to Oleg for several rounds of review and insights.
[akpm@linux-foundation.org: fix comment layout and spelling]
[akpm@linux-foundation.org: add lengthy code comment from Oleg]
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to the alignment of following variables, these typically consume
more than just the single byte that 'bool' requires, and as there are a
few hundred instances, the cache pollution (not so much the waste of
memory) sums up. Put these variables into their own section, outside of
any half way frequently used memory range.
Do the same also to the __warned variable of rcu_lockdep_assert().
(Don't, however, include the ones used by printk_once() and alike, as
they can potentially be hot.)
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This addresses some header check warnings. DRM headers which include
"drm.h" have been excluded, as they indirectly include types.h.
Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARCH_HAS_NMI_WATCHDOG is a macro defined by arch, but config
HARDLOCKUP_DETECTOR depends on it. This is wrong, ARCH_HAS_NMI_WATCHDOG
has to be a Kconfig config, and arch's need it should select it
explicitly.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Move open-coded filesystem magic numbers into magic.h
- Rearrange magic.h so that the filesystem-related constants are grouped
together.
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9863c90f68 (x86, vmware: Remove
deprecated VMI kernel support) removed the only place which set
no_sync_cmos_clock. Since that commit, this variable is never set.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull media updates from Mauro Carvalho Chehab:
- V4L2 API additions to better support JPEG compression control
- media API additions to properly support MPEG decoders
- V4L2 API additions for image crop/scaling
- a few other V4L2 API DocBook fixes/improvements
- two new DVB frontend drivers: m88rs2000 and rtl2830
- two new DVB drivers: az6007 and rtl28xxu
- a framework for ISA drivers, that removed lots of common code found
at the ISA radio drivers
- a new FM transmitter driver (radio-keene)
- a GPIO-based IR receiver driver
- a new sensor driver: mt9m032
- some new video drivers: adv7183, blackfin, mx2_emmaprp, sii9234_drv,
vs6624
- several new board additions, driver fixes, improvements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (295 commits)
[media] update CARDLIST.em28xx
[media] partially reverts changeset fa5527c
[media] stb0899: fix the limits for signal strength values
[media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
[media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
[media] -EINVAL -> -ENOTTY
[media] gspca - sn9c20x: Cleanup source
[media] gspca - sn9c20x: Simplify register write for capture start/stop
[media] gspca - sn9c20x: Add automatic JPEG compression mechanism
[media] gspca - sn9c20x: Greater delay in case of sensor no response
[media] gspca - sn9c20x: Optimize the code of write sequences
[media] gspca - sn9c20x: Add the JPEG compression quality control
[media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
[media] gspca - sn9c20x: Propagate USB errors to higher level
[media] gspca - sn9c20x: Use the new video control mechanism
[media] gspca - sn9c20x: Fix loss of frame start
[media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
[media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
[media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
[media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
...
they contain two new IOMMU drivers for the ARM Tegra 2 and 3 platforms.
Besides that there are also a few patches for the AMD IOMMU which
prepare the driver for adding intr-remapping support and a couple of
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lCBm
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"The IOMMU updates for this round are not very large patch-wise. But
they contain two new IOMMU drivers for the ARM Tegra 2 and 3
platforms. Besides that there are also a few patches for the AMD
IOMMU which prepare the driver for adding intr-remapping support and a
couple of fixes."
* tag 'iommu-updates-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix section mismatch
iommu/amd: Move interrupt setup code into seperate function
iommu/amd: Make sure IOMMU interrupts are re-enabled on resume
iommu/amd: Fix section warning for prealloc_protection_domains
iommu/amd: Don't initialize IOMMUv2 resources when not required
iommu/amd: Update git-tree in MAINTAINERS
iommu/tegra-gart: fix spin_unlock in map failure path
iommu/amd: Fix double free of mem-region in error-path
iommu/amd: Split amd_iommu_init function
ARM: IOMMU: Tegra30: Add iommu_ops for SMMU driver
ARM: IOMMU: Tegra20: Add iommu_ops for GART driver
Pull i2c embedded updates from Wolfram Sang:
"Nothing special from i2c-embedded for this merge window. Two new
drivers, minor feature additions, bugfixes, cleanups.
All patches have been in linux-next for some time, too."
* 'i2c-embedded/for-3.4' of git://git.pengutronix.de/git/wsa/linux:
i2c-eg20t: Remove write-only variables
i2c-eg20t: Rework pch_i2c_wait_for_bus_idle to reduce wait time
i2c-s3c2410: Add stub runtime power management
i2c-s3c2410: Convert to devm_kzalloc()
i2c: add CSR SiRFprimaII on-chip I2C controllers driver
i2c: tegra: Remove unnecessary write to INT_STATUS
i2c: imx: fix imx driver to work though signal is pending
i2c: designware: dw_i2c_init_driver as subsys initcall
misc: at24: describe platform_data with kernel_doc
i2c: Move I2C_EG20T option to the right place.
i2c: Support for Netlogic XLR/XLS I2C controller.
i2c: mpc: Add support for SMBUS_READ_BLOCK_DATA
i2c: versatile: Add Device Tree support
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
New features include:
- Add NFS client support for containers.
This should enable most of the necessary functionality, including
lockd support, and support for rpc.statd, NFSv4 idmapper and
RPCSEC_GSS upcalls into the correct network namespace from
which the mount system call was issued.
- NFSv4 idmapper scalability improvements
Base the idmapper cache on the keyring interface to allow concurrent
access to idmapper entries. Start the process of migrating users from
the single-threaded daemon-based approach to the multi-threaded
request-key based approach.
- NFSv4.1 implementation id.
Allows the NFSv4.1 client and server to mutually identify each other
for logging and debugging purposes.
- Support the 'vers=4.1' mount option for mounting NFSv4.1 instead of
having to use the more counterintuitive 'vers=4,minorversion=1'.
- SUNRPC tracepoints.
Start the process of adding tracepoints in order to improve debugging
of the RPC layer.
- pNFS object layout support for autologin.
Important bugfixes include:
- Fix a bug in rpc_wake_up/rpc_wake_up_status that caused them to fail
to wake up all tasks when applied to priority waitqueues.
- Ensure that we handle read delegations correctly, when we try to
truncate a file.
- A number of fixes for NFSv4 state manager loops (mostly to do with
delegation recovery).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LuHE
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.4-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates for Linux 3.4 from Trond Myklebust:
"New features include:
- Add NFS client support for containers.
This should enable most of the necessary functionality, including
lockd support, and support for rpc.statd, NFSv4 idmapper and
RPCSEC_GSS upcalls into the correct network namespace from which
the mount system call was issued.
- NFSv4 idmapper scalability improvements
Base the idmapper cache on the keyring interface to allow
concurrent access to idmapper entries. Start the process of
migrating users from the single-threaded daemon-based approach to
the multi-threaded request-key based approach.
- NFSv4.1 implementation id.
Allows the NFSv4.1 client and server to mutually identify each
other for logging and debugging purposes.
- Support the 'vers=4.1' mount option for mounting NFSv4.1 instead of
having to use the more counterintuitive 'vers=4,minorversion=1'.
- SUNRPC tracepoints.
Start the process of adding tracepoints in order to improve
debugging of the RPC layer.
- pNFS object layout support for autologin.
Important bugfixes include:
- Fix a bug in rpc_wake_up/rpc_wake_up_status that caused them to
fail to wake up all tasks when applied to priority waitqueues.
- Ensure that we handle read delegations correctly, when we try to
truncate a file.
- A number of fixes for NFSv4 state manager loops (mostly to do with
delegation recovery)."
* tag 'nfs-for-3.4-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (224 commits)
NFS: fix sb->s_id in nfs debug prints
xprtrdma: Remove assumption that each segment is <= PAGE_SIZE
xprtrdma: The transport should not bug-check when a dup reply is received
pnfs-obj: autologin: Add support for protocol autologin
NFS: Remove nfs4_setup_sequence from generic rename code
NFS: Remove nfs4_setup_sequence from generic unlink code
NFS: Remove nfs4_setup_sequence from generic read code
NFS: Remove nfs4_setup_sequence from generic write code
NFS: Fix more NFS debug related build warnings
SUNRPC/LOCKD: Fix build warnings when CONFIG_SUNRPC_DEBUG is undefined
nfs: non void functions must return a value
SUNRPC: Kill compiler warning when RPC_DEBUG is unset
SUNRPC/NFS: Add Kbuild dependencies for NFS_DEBUG/RPC_DEBUG
NFS: Use cond_resched_lock() to reduce latencies in the commit scans
NFSv4: It is not safe to dereference lsp->ls_state in release_lockowner
NFS: ncommit count is being double decremented
SUNRPC: We must not use list_for_each_entry_safe() in rpc_wake_up()
Try using machine credentials for RENEW calls
NFSv4.1: Fix a few issues in filelayout_commit_pagelist
NFSv4.1: Clean ups and bugfixes for the pNFS read/writeback/commit code
...
Get rid of INLINE_SPIN_UNLOCK entirely replacing it with
UNINLINE_SPIN_UNLOCK instead of the reverse meaning.
Whoever wants to change the default spinlock inlining
behavior and uninline the spinlocks for some weird reason,
such as spinlock debugging, paravirt etc. can now all just
select UNINLINE_SPIN_UNLOCK
Original discussion at: https://lkml.org/lkml/2012/3/21/357
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20120322095502.30866.75756.sendpatchset@codeblue
[ tidied up the changelog a bit ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Complete the syscall-less self-profiling feature and address
all complaints, namely:
- capabilities, so we can detect what is actually available at runtime
Add a capabilities field to perf_event_mmap_page to indicate
what is actually available for use.
- on x86: RDPMC weirdness due to being 40/48 bits and not sign-extending
properly.
- ABI documentation as to how all this stuff works.
Also improve the documentation for the new features.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vweaver1@eecs.utk.edu>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1332433596.2487.33.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
. Short term fix for 'diff' tool breakage related to perf.data files
with multiple events. From Jiri Olsa
. Cleanup for event id tracepoint reading routine, from Borislav Petkov
. 32-bit compilation fixes from Jiri Olsa
. Event parsing modifier assignment fixes from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=V7d9
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Cleanups and fixes for perf/core:
. Short term fix for 'diff' tool breakage related to perf.data files
with multiple events. From Jiri Olsa
. Cleanup for event id tracepoint reading routine, from Borislav Petkov
. 32-bit compilation fixes from Jiri Olsa
. Event parsing modifier assignment fixes from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It includes:
- drivers for Samsung Exynos MIPI DSI and display port
- i740fb to support those old Intel chips
- large updates to OMAP, viafb and sh_mobile_lcdcfb
- some updates to s3c-fb and udlfb, few patches to others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=uO8m
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.4' of git://github.com/schandinat/linux-2.6
Pull fbdev updates for 3.4 from Florian Tobias Schandinat:
- drivers for Samsung Exynos MIPI DSI and display port
- i740fb to support those old Intel chips
- large updates to OMAP, viafb and sh_mobile_lcdcfb
- some updates to s3c-fb and udlfb, few patches to others
Fix up conflicts in drivers/video/udlfb.c due to Key Sievers' fix making
it in twice.
* tag 'fbdev-updates-for-3.4' of git://github.com/schandinat/linux-2.6: (156 commits)
Revert "video:uvesafb: Fix oops that uvesafb try to execute NX-protected page"
OMAPDSS: register dss drivers in module init
video: pxafb: add clk_prepare/clk_unprepare calls
fbdev: bfin_adv7393fb: Drop needless include
fbdev: sh_mipi_dsi: add extra phyctrl for sh_mipi_dsi_info
fbdev: remove dependency of FB_SH_MOBILE_MERAM from FB_SH_MOBILE_LCDC
Revert "MAINTAINERS: add entry for exynos mipi display drivers"
fbdev: da8xx: add support for SP10Q010 display
fbdev: da8xx:: fix reporting of the display timing info
drivers/video/pvr2fb.c: ensure arguments to request_irq and free_irq are compatible
OMAPDSS: APPLY: fix clearing shadow dirty flag with manual update
fbdev: sh_mobile_meram: Implement system suspend/resume
fbdev: sh_mobile_meram: Remove unneeded sanity checks
fbdev: sh_mobile_meram: Don't perform update in register operation
arm: mach-shmobile: Constify sh_mobile_meram_cfg structures
fbdev: sh_mobile_lcdc: Don't store copy of platform data
fbdev: sh_mobile_meram: Remove unused sh_mobile_meram_icb_cfg fields
arm: mach-shmobile: Don't set MERAM ICB numbers in platform data
fbdev: sh_mobile_meram: Allocate ICBs automatically
fbdev: sh_mobile_meram: Use genalloc to manage MERAM allocation
...
seeing a trickle of new features coming in they're getting much smaller
than they were. It's also nice to have some features which support
other subsystems building infrastructure on top of regmap. Highlights
include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring the
register state. This is intended to be used to apply updates supplied by
manufacturers for tuning the performance of the device (many of which
are to undocumented registers which aren't otherwise covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for other
subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Eo9
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Things are really quieting down with the regmap API, while we're still
seeing a trickle of new features coming in they're getting much
smaller than they were. It's also nice to have some features which
support other subsystems building infrastructure on top of regmap.
Highlights include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring
the register state. This is intended to be used to apply updates
supplied by manufacturers for tuning the performance of the device
(many of which are to undocumented registers which aren't otherwise
covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for
other subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (41 commits)
regmap: Fix future missing prototype of devres_alloc() and friends
regmap: Rejig struct declarations for stubbed API
regmap: Fix rbtree block base in sync
regcache: Make sure we sync register 0 in an rbtree cache
regmap: delete unused module.h from drivers/base/regmap files
regmap: Add stub for regcache_sync_region()
mfd: Improve performance of later WM1811 revisions
regmap: Fix x86_64 breakage
regmap: Allow drivers to sync only part of the register cache
regmap: Supply ranges to the sync operations
regmap: Add tracepoints for cache only and cache bypass
regmap: Mark the cache as clean after a successful sync
regmap: Remove default cache sync implementation
regmap: Skip hardware defaults for LZO caches
regmap: Expose the driver name in debugfs
mfd: wm8400: Convert to devm_regmap_init_i2c()
mfd: wm831x: Convert to devm_regmap_init()
mfd: wm8994: Convert to devm_regmap_init()
mfd/ASoC: Convert WM8994 driver to use regmap patches
mfd: Add __devinit and __devexit annotations in wm8994
...
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=oWbr
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates post v3.3 from Stefan Richter:
- Some SBP-2 initiator fixes, side product from ongoing work on a target.
- Reintroduction of an isochronous I/O feature of the older ieee1394 driver
stack (flush buffer completions); it was evidently rarely used but not
actually unused. Matching libraw1394 code is already available.
- Be sure to prefix all kernel log messages with device name or card name,
and other logging related cleanups.
- Misc other small cleanups, among them a small API change that affects
sound/firewire/ too. Clemens Ladisch is aware of it.
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394: (26 commits)
firewire: allow explicit flushing of iso packet completions
firewire: prevent dropping of completed iso packet header data
firewire: ohci: factor out iso completion flushing code
firewire: ohci: simplify iso header pointer arithmetic
firewire: ohci: optimize control bit checks
firewire: ohci: remove unused excess_bytes field
firewire: ohci: copy_iso_headers(): make comment match the code
firewire: cdev: fix IR multichannel event documentation
firewire: ohci: fix too-early completion of IR multichannel buffers
firewire: ohci: move runtime debug facility out of #ifdef
firewire: tone down some diagnostic log messages
firewire: sbp2: replace a GFP_ATOMIC allocation
firewire: sbp2: Fix SCSI sense data mangling
firewire: sbp2: Ignore SBP-2 targets on the local node
firewire: sbp2: Take into account Unit_Unique_ID
firewire: nosy: Use the macro DMA_BIT_MASK().
firewire: core: convert AR-req handler lock from _irqsave to _bh
firewire: core: fix race at address_handler unregistration
firewire: core: remove obsolete comment
firewire: core: prefix log messages with card name
...
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Gg7v
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates for v3.4 from Linus Walleij (*):
- Switches the PXA 168, 910 and MMP over to use pinctrl
- Locking revamped
- Massive refactorings...
- Reform the driver API to use multiple states
- Support pin config in the mapping tables
- Pinctrl drivers for the nVidia Tegra series
- Generic pin config support lib for simple pin controllers
- Implement pin config for the U300
* tag 'pinctrl-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
ARM: u300: configure some pins as an example
pinctrl: support pinconfig on the U300
pinctrl/coh901: use generic pinconf enums and parameters
pinctrl: introduce generic pin config
pinctrl: fix error path in pinconf_map_to_setting()
pinctrl: allow concurrent gpio and mux function ownership of pins
pinctrl: forward-declare struct device
pinctrl: split pincontrol states into its own header
pinctrl: include machine header to core.h
ARM: tegra: Select PINCTRL Kconfig variables
pinctrl: add a driver for NVIDIA Tegra
pinctrl: Show selected function and group in pinmux-pins debugfs
pinctrl: enhance mapping table to support pin config operations
pinctrl: API changes to support multiple states per device
pinctrl: add usecount to pins for muxing
pinctrl: refactor struct pinctrl handling in core.c vs pinmux.c
pinctrl: fix and simplify locking
pinctrl: fix the pin descriptor kerneldoc
pinctrl: assume map table entries can't have a NULL name field
pinctrl: introduce PINCTRL_STATE_DEFAULT, define hogs as that state
...
(*) What is it with all these Linuses these days? There's a Linus at
google too. Some day I will get myself my own broadsword, and run
around screaming "There can be only one".
I used to be _special_ dammit. Snif.
Pull input subsystem updates from Dmitry Torokhov:
"- we finally merged driver for USB version of Synaptics touchpads
(I guess most commonly found in IBM/Lenovo keyboard/touchpad combo);
- a bunch of new drivers for embedded platforms (Cypress
touchscreens, DA9052 OnKey, MAX8997-haptic, Ilitek ILI210x
touchscreens, TI touchscreen);
- input core allows clients to specify desired clock source for
timestamps on input events (EVIOCSCLOCKID ioctl);
- input core allows querying state of all MT slots for given event
code via EVIOCGMTSLOTS ioctl;
- various driver fixes and improvements."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: ili210x - add support for Ilitek ILI210x based touchscreens
Input: altera_ps2 - use of_match_ptr()
Input: synaptics_usb - switch to module_usb_driver()
Input: convert I2C drivers to use module_i2c_driver()
Input: convert SPI drivers to use module_spi_driver()
Input: omap4-keypad - move platform_data to <linux/platform_data>
Input: kxtj9 - who_am_i check value and initial data rate fixes
Input: add driver support for MAX8997-haptic
Input: tegra-kbc - revise device tree support
Input: of_keymap - add device tree bindings for simple key matrices
Input: wacom - fix physical size calculation for 3rd-gen Bamboo
Input: twl4030-vibra - really switch from #if to #ifdef
Input: hp680_ts_input - ensure arguments to request_irq and free_irq are compatible
Input: max8925_onkey - avoid accessing input device too early
Input: max8925_onkey - allow to be used as a wakeup source
Input: atmel-wm97xx - convert to dev_pm_ops
Input: atmel-wm97xx - set driver owner
Input: add cyttsp touchscreen maintainer entry
Input: cyttsp - remove useless checks in cyttsp_probe()
Input: usbtouchscreen - add support for Data Modul EasyTouch TP 72037
...
- PV multiconsole support, so that there can be hvc1, hvc2, etc;
- P-state and C-state power management driver that uploads said
power management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPZ0qkAAoJEFjIrFwIi8fJjCgH/jeJ39E8ML8DP9tCS2HQnMqM
uTEjLcqvoJ7sEhHvtBLPeG2p0jyBvOWjLbSc7P8nESBAMPvSYol8L6WqfWrdSU4r
lHrma2sg9UYzRog5NyxAgkp7bBsBBFOnhVL3Cxb5Ig78cPWzeSWGpqGZ8M/d51Wf
1iE0tHuU4DpN+fg1SZqPqEm8ecEJ/eSrVTnyTx/Qo2Ak+Zw98SqzX7SV5lo8mudd
WFL1F2K9FyTNk79ndGhqFt36x6nEbFgMLbmCDWumLuWN6bMd1Uq0wNkCqW4F1h28
3yqnY+rfQh4y3eXK1B9nttCUTs+/66U5ZWrT6B1IJumGTAIqcWfgeUX/Vn/HVC4=
=tfMc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
into debugfs, and use __read_mostly as neccessary.
Also add a MAINTAINER file for cleancache API files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPZ1sjAAoJEFjIrFwIi8fJCSkIALqBBCkuPSusvdebT59Oq145
EW2eEwJzVft0vlvS/IPl+W37TH5VWhBVCW8frAYMpLaY5X/W1ZwzFpx76T4acAiM
wkXwsyYXs6N13OOFoH5gmf3cwproAioRxbEeALucxeMR4rK5Yw+oZXT+hSu2KaLh
1LtHyx+u+NLb0QOseAuDcmyjY9r6aLBA1HMcVD2z+4UW1n/9NWexQP3ShYP9uMDs
GnyDzZ8vWXTcoc4Auj0rpaNsT5d47ltGegKASZmmvS3QyMHbZ4sk2HECnQY4wSee
alPJwDyb6mOJmQ3e4s940onjfZPgd8/cW/DVEUrveH+dz6Eqjxqz41dVRVXiLz8=
=tUNC
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm
Pull cleancache changes from Konrad Rzeszutek Wilk:
"This has some patches for the cleancache API that should have been
submitted a _long_ time ago. They are basically cleanups:
- rename of flush to invalidate
- moving reporting of statistics into debugfs
- use __read_mostly as necessary.
Oh, and also the MAINTAINERS file change. The files (except the
MAINTAINERS file) have been in #linux-next for months now. The late
addition of MAINTAINERS file is a brain-fart on my side - didn't
realize I needed that just until I was typing this up - and I based
that patch on v3.3 - so the tree is on top of v3.3."
* tag 'stable/for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
MAINTAINERS: Adding cleancache API to the list.
mm: cleancache: Use __read_mostly as appropiate.
mm: cleancache: report statistics via debugfs instead of sysfs.
mm: zcache/tmem/cleancache: s/flush/invalidate/
mm: cleancache: s/flush/invalidate/
Since commit 7dffa3c673 the ntp
subsystem has used an hrtimer for triggering the leapsecond
adjustment. However, this can cause a potential livelock.
Thomas diagnosed this as the following pattern:
CPU 0 CPU 1
do_adjtimex()
spin_lock_irq(&ntp_lock);
process_adjtimex_modes(); timer_interrupt()
process_adj_status(); do_timer()
ntp_start_leap_timer(); write_lock(&xtime_lock);
hrtimer_start(); update_wall_time();
hrtimer_reprogram(); ntp_tick_length()
tick_program_event() spin_lock(&ntp_lock);
clockevents_program_event()
ktime_get()
seq = req_seqbegin(xtime_lock);
This patch tries to avoid the problem by reverting back to not using
an hrtimer to inject leapseconds, and instead we handle the leapsecond
processing in the second_overflow() function.
The downside to this change is that on systems that support highres
timers, the leap second processing will occur on a HZ tick boundary,
(ie: ~1-10ms, depending on HZ) after the leap second instead of
possibly sooner (~34us in my tests w/ x86_64 lapic).
This patch applies on top of tip/timers/core.
CC: Sasha Levin <levinsasha928@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Diagnoised-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch introduces nf_conntrack_l4proto_find_get() and
nf_conntrack_l4proto_put() to fix module dependencies between
timeout objects and l4-protocol conntrack modules.
Thus, we make sure that the module cannot be removed if it is
used by any of the cttimeout objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull radeon southern islands / trinity support from Dave Airlie:
"This is support from AMD for their newest GPU and APUs. The products
called RadeonHD 7xxx, and the Trinity APU series.
This did come in a bit late, due to some over-complicated AMD internal
review process, which from the outside seems unnecessary once the
company has decided it wants to support open source. However as I
said previously I'd rather not put the people who've got this hw for 3
months now being forced to use fglrx on it if there is open code.
Its pretty well self contained and just plugs into the driver in
various places."
* 'drm-radeon-sitn-support' of git://people.freedesktop.org/~airlied/linux: (48 commits)
drm/radeon/kms: update duallink checks for DCE6
drm/radeon/kms: add trinity pci ids
drm/radeon/kms: add radeon_asic struct for trinity
drm/radeon/kms: add support for ucode loading on trinity (v2)
drm/radeon/kms/vm: set vram base offset properly for TN
drm/radeon/kms: Update evergreen functions for trinity
drm/radeon/kms: cayman gpu init updates for trinity
drm/radeon/kms: Add checks for TN in the DP bridge code
drm/radeon/kms/DCE6.1: ss is not supported on the internal pplls
drm/radeon/kms: disable PPLL0 on DCE6.1 when not in use
drm/radeon/kms: Adjust pll picker for DCE6.1
drm/radeon/kms: DCE6.1 disp eng pll updates
drm/radeon/kms: DCE6.1 watermark updates for TN
drm/radeon/kms: no support for internal thermal sensor on TN yet
drm/radeon/kms: add trinity (TN) chip family
drm/radeon/kms: Add SI pci ids
drm/radeon: Update radeon_info_ioctl for SI. (v2)
drm/radeon/kms: add radeon_asic struct for SI
drm/radeon/kms: add support for compute rings in CS ioctl on SI
drm/radeon/kms: fill in startup/shutdown callbacks for SI
...
Pull drm main changes from Dave Airlie:
"This is the main drm pull request, I'm probably going to send two more
smaller ones, will explain below.
This contains a patch that is also in the fbdev tree, but it should be
the same patch, it added an API for hot unplugging framebuffer
devices, and I need that API for a new driver.
It also contains some changes to the i2c tree which Jean has acked,
and one change to moorestown platform stuff in x86.
Highlights:
- new drivers: UDL driver for USB displaylink devices, kms only,
should support correct hotplug operations.
- core: i2c speedups + better hotplug support, EDID overriding via
firmware interface - allows user to load a firmware for a broken
monitor/kvm from userspace, it even has documentation for it.
- exynos: new HDMI audio + hdmi 1.4 + virtual output driver
- gma500: code cleanup
- radeon: cleanups, CS optimisations, streamout support and pageflip
fix
- nouveau: NVD9 displayport support + more reclocking work
- i915: re-enabling GMBUS, finish gpu patch (might help hibernation
who knows), missed irq fixes, stencil tiling fixes, interlaced
support, aliasesd PPGTT support for SNB/IVB, swizzling for SNB/IVB,
semaphore fixes
As well as the usual bunch of cleanups and fixes all over the place.
I've got two things I'd like to merge a bit later:
a) AMD support for all their new radeonhd 7000 series GPU and APUs.
AMD dropped this a bit late due to insane internal review
processes, (please AMD just follow Intel and let open source guys
ship stuff early) however I don't want to penalise people who own
this hardware (since its been on sale for 3-4 months and GPU hw
doesn't exactly have a lifetime in years) and consign them to
using closed drivers for longer than necessary. The changes are
well contained and just plug into the driver new gpu functionality
so they should be fairly regression proof. I just want to give
them a bit of a run on the hw AMD kindly sent me.
b) drm prime/dma-buf interface code. This is just infrastructure
code to expose the dma-buf stuff to drm drivers and to userspace.
I'm not planning on pushing any driver support in this cycle
(except maybe exynos), but I'd like to get the infrastructure code
in so for the next cycle I can start getting the driver support
into the individual drivers. We have started driver support for
i915, nouveau and udl along with I think exynos and omap in
staging. However this code relies on the dma-buf tree being
pulled into your tree first since it needs the latest interfaces
from that tree. I'll push to get that tree sent asap.
(oh and any warnings you see in i915 are gcc's fault from what anyone
can see)."
Fix up trivial conflicts in arch/x86/platform/mrst/mrst.c due to the new
msic_thermal_platform_data() thermal function being added next to the
tc35876x_platform_data() i2c device function..
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (326 commits)
drm/i915: use DDC_ADDR instead of hard-coding it
drm/radeon: use DDC_ADDR instead of hard-coding it
drm: remove unneeded redefinition of DDC_ADDR
drm/exynos: added virtual display driver.
drm: allow loading an EDID as firmware to override broken monitor
drm/exynos: enable hdmi audio feature
drm/exynos: add default pixel format for plane
drm/exynos: cleanup exynos_hdmi.h
drm/exynos: add is_local member in exynos_drm_subdrv struct
drm/exynos: add subdrv open/close functions
drm/exynos: remove module of exynos drm subdrv
drm/exynos: release pending pageflip events when closed
drm/exynos: added new funtion to get/put dma address.
drm/exynos: update gem and buffer framework.
drm/exynos: added mode_fixup feature and code clean.
drm/exynos: add HDMI version 1.4 support
drm/exynos: remove exynos_mixer.h
gma500: Fix mmap frambuffer
drm/radeon: Drop radeon_gem_object_(un)pin.
drm/radeon: Restrict offset for legacy display engine.
...
Here is the first big update chunk of sound stuff for 3.4-rc1.
In the common sound infrastructure, there are a few changes for
dynamic PCM support (used in ASoC) and a few clean-ups. Majority of
changes are found, as usual, in HD-audio and ASoC.
Some highlights of HD-audio changes:
- All the long-standing static quirk codes for Realtek codec were
finally removed by fixing and extending the Realtek auto-parser.
- The mute-LED control is standardized over all HD-audio codec
drivers using the extended vmaster hook.
- The vmaster slave mixer elements are initialized to 0dB as default
so that the user won't be annoyed by the silent output after
updates, e.g. due to the additions of new elements.
- Other many fix-ups for the misc HD-audio devices.
In the ASoC side, this is a very active release, including a quite a
few framework enhancements. Some highlights:
- Support for widgets not associated with a CODEC, an important part
of the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based
DMA drivers contributed by Lars-Peter Clausen. This will save a lot
of code and make it much easier to deploy enhancements to
dmaengine.
- Support for binary controls, used for providing runtime
configuration of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do
without any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort
to put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to
DMAEngine.
- Conversion of EP93xx drivers to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics
WM2200.
- Move audmux driver from arc/arm to sound/soc
- McBSP move from arch/ to sound/ and updates
Also, a few small updates and fixes for other drivers like au88x0,
ymfpci, USB 6fire, USB usx2yaudio are included.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPawmuAAoJEGwxgFQ9KSmkdR0QALDDI/eUo4il40C33Gt/OSDz
Wkz+FOwp2ddbIqHc0n41sV7+FV1MuyzQ37uSw8zhK724Vd4tCqX6O5K1uvS1iSbh
jxHsy5XtfvCs2cjb61H6N+rfWcqC69gGhpc1mLoelj/PYl7S2iV5xOgTr4trVk2Y
UN7Y13b4hzZvubRUozoTldaIgdhrj8D8KO7qQNYehyG19b4bJ00Rk4K5JdjsFwbE
dTGl/ZUv50Fnx6PAWwqzh1a3cPabHA1TZDiKQM2nuE91e/Ecs4c7t1CRvW8m8mlr
u4D4N8PJcCN4SPDd2YuVBgan4SQ0kxKTaup11bHSvAWai2zPX5xMB1yoJNxgjSMt
5NHrGdR4+lQEVlBVXe2sWb4/3vE2kr2dtcGGR/FBFJTuLWDFFtRcnxeQJI8qRNUw
UdwDuGXdActoc1cZz2dsKvXMOs0TKT6OCdQH+dHBglW/W8wMkVocZclUgbQM66/X
gwvk0jfZ9p3UcKnYt3RkxiXQvAJsr8v0HhYcKvQCFhJArZufdeRHB7LCVRTm692Y
/BKZgK4QHxtGw3Yc7emYidKeRSP1ml5QlvC4zMIoGqiahqa8LI8Qcb5knvIEmU8q
kY5k0fVP+paf0dceAVXyFZsRB9AyX2eUdufDPifXtydQZgj4o9A7Sy/teWl77EgF
Mafq4QUzo1U4i8JpAM4d
=5FJq
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull updates of sound stuff from Takashi Iwai:
"Here is the first big update chunk of sound stuff for 3.4-rc1.
In the common sound infrastructure, there are a few changes for
dynamic PCM support (used in ASoC) and a few clean-ups. Majority of
changes are found, as usual, in HD-audio and ASoC.
Some highlights of HD-audio changes:
- All the long-standing static quirk codes for Realtek codec were
finally removed by fixing and extending the Realtek auto-parser.
- The mute-LED control is standardized over all HD-audio codec
drivers using the extended vmaster hook.
- The vmaster slave mixer elements are initialized to 0dB as default
so that the user won't be annoyed by the silent output after
updates, e.g. due to the additions of new elements.
- Other many fix-ups for the misc HD-audio devices.
In the ASoC side, this is a very active release, including a quite a
few framework enhancements. Some highlights:
- Support for widgets not associated with a CODEC, an important part
of the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based
DMA drivers contributed by Lars-Peter Clausen. This will save a
lot of code and make it much easier to deploy enhancements to
dmaengine.
- Support for binary controls, used for providing runtime
configuration of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do
without any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much
effort to put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to
DMAEngine.
- Conversion of EP93xx drivers to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics
WM2200.
- Move audmux driver from arc/arm to sound/soc
- McBSP move from arch/ to sound/ and updates
Also, a few small updates and fixes for other drivers like au88x0,
ymfpci, USB 6fire, USB usx2yaudio are included."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (446 commits)
ASoC: wm8994: Provide VMID mode control and fix default sequence
ASoC: wm8994: Add missing break in resume
ASoC: wm_hubs: Don't actively manage LINEOUT_VMID_BUF
ASoC: pxa-ssp: atomically set stream active masks
ASoC: fsl: p1022ds: tell the WM8776 codec driver that it's the master
ASoC: Samsung: Added to support mono recording
ALSA: hda - Fix build with CONFIG_PM=n
ALSA: au88x0 - Avoid possible Oops at unbinding
ALSA: usb-audio - Fix build error by consitification of rate list
ASoC: core: Fix obscure leak of runtime array
ALSA: pcm - Avoid GFP_ATOMIC in snd_pcm_link()
ALSA: pcm: Constify the list in snd_pcm_hw_constraint_list
ASoC: wm8996: Add 44.1kHz support
ALSA: hda - Fix build of patch_sigmatel.c without CONFIG_SND_HDA_POWER_SAVE
ASoC: mx27vis-aic32x4: Convert it to platform driver
ALSA: hda - fix printing of high HDMI sample rates
ALSA: ymfpci - Fix legacy registers on S3/S4 resume
ALSA: control - Fixe a trailing white space error
ALSA: hda - Add expose_enum_ctl flag to snd_hda_add_vmaster_hook()
ALSA: hda - Add "Mute-LED Mode" enum control
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
Mostly tidying up code in preparation for some bigger changes
next time.
A few bug fixes tagged for -stable.
Main functionality change is that some RAID10 arrays can now
grow to use extra space that may have been made available on the
individual devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=MGuM
-----END PGP SIGNATURE-----
Merge tag 'md-3.4' of git://neil.brown.name/md
Pull md updates for 3.4 from Neil Brown:
"Mostly tidying up code in preparation for some bigger changes next
time.
A few bug fixes tagged for -stable.
Main functionality change is that some RAID10 arrays can now grow to
use extra space that may have been made available on the individual
devices."
Fixed up trivial conflicts with the k[un]map_atomic() cleanups in
drivers/md/bitmap.c.
* tag 'md-3.4' of git://neil.brown.name/md: (22 commits)
md: Add judgement bb->unacked_exist in function md_ack_all_badblocks().
md: fix clearing of the 'changed' flags for the bad blocks list.
md/bitmap: discard CHUNK_BLOCK_SHIFT macro
md/bitmap: remove unnecessary indirection when allocating.
md/bitmap: remove some pointless locking.
md/bitmap: change a 'goto' to a normal 'if' construct.
md/bitmap: move printing of bitmap status to bitmap.c
md/bitmap: remove some unused noise from bitmap.h
md/raid10 - support resizing some RAID10 arrays.
md/raid1: handle merge_bvec_fn in member devices.
md/raid10: handle merge_bvec_fn in member devices.
md: add proper merge_bvec handling to RAID0 and Linear.
md: tidy up rdev_for_each usage.
md/raid1,raid10: avoid deadlock during resync/recovery.
md/bitmap: ensure to load bitmap when creating via sysfs.
md: don't set md arrays to readonly on shutdown.
md: allow re-add to failed arrays.
md/raid5: use atomic_dec_return() instead of atomic_dec() and atomic_read().
md: Use existed macros instead of numbers
md/raid5: removed unused 'added_devices' variable.
...
Pull x86 platform changes from Ingo Molnar.
Removes the Moorestown platform that nobody ever used.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Move APIC ID validity check into platform APIC code
x86/olpc/xo15/sci: Enable lid close wakeup control
x86/geode/net5501: Add platform driver for Soekris Engineering net5501
x86/geode/alix2: Supplement driver to include GPIO button support
x86/mid/powerbtn: Use MSIC read/write instead of ipc_scu
x86/mid/thermal: Turn off thermistor
x86/mid/thermal: Add msic_thermal alias
x86/mid/thermal: Convert to use Intel MSIC API
x86/mid/scu_ipc: Remove Moorestown support
x86/mid: Kill off Moorestown
x86/mrst: Add msic_thermal platform support
x86/config: Select MSIC MFD driver on Intel Medfield platform
x86/mid: Remove Intel Moorestown
x86/mrst: Set ISA bus type for fake MP IRQs
x86/ioapic: Use legacy_pic to set correct gsi-irq mapping
Pull MCE changes from Ingo Molnar.
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix return value of mce_chrdev_read() when erst is disabled
x86/mce: Convert static array of pointers to per-cpu variables
x86/mce: Replace hard coded hex constants with symbolic defines
x86/mce: Recognise machine check bank signature for data path error
x86/mce: Handle "action required" errors
x86/mce: Add mechanism to safely save information in MCE handler
x86/mce: Create helper function to save addr/misc when needed
HWPOISON: Add code to handle "action required" errors.
HWPOISON: Clean up memory_failure() vs. __memory_failure()
Pull x86/asm changes from Ingo Molnar
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Include probe_roms.h in probe_roms.c
x86/32: Print control and debug registers for kerenel context
x86: Tighten dependencies of CPU_SUP_*_32
x86/numa: Improve internode cache alignment
x86: Fix the NMI nesting comments
x86-64: Improve insn scheduling in SAVE_ARGS_IRQ
x86-64: Fix CFI annotations for NMI nesting code
bitops: Add missing parentheses to new get_order macro
bitops: Optimise get_order()
bitops: Adjust the comment on get_order() to describe the size==0 case
x86/spinlocks: Eliminate TICKET_MASK
x86-64: Handle byte-wise tail copying in memcpy() without a loop
x86-64: Fix memcpy() to support sizes of 4Gb and above
x86-64: Fix memset() to support sizes of 4Gb and above
x86-64: Slightly shorten copy_page()
Merge first batch of patches from Andrew Morton:
"A few misc things and all the MM queue"
* emailed from Andrew Morton <akpm@linux-foundation.org>: (92 commits)
memcg: avoid THP split in task migration
thp: add HPAGE_PMD_* definitions for !CONFIG_TRANSPARENT_HUGEPAGE
memcg: clean up existing move charge code
mm/memcontrol.c: remove unnecessary 'break' in mem_cgroup_read()
mm/memcontrol.c: remove redundant BUG_ON() in mem_cgroup_usage_unregister_event()
mm/memcontrol.c: s/stealed/stolen/
memcg: fix performance of mem_cgroup_begin_update_page_stat()
memcg: remove PCG_FILE_MAPPED
memcg: use new logic for page stat accounting
memcg: remove PCG_MOVE_LOCK flag from page_cgroup
memcg: simplify move_account() check
memcg: remove EXPORT_SYMBOL(mem_cgroup_update_page_stat)
memcg: kill dead prev_priority stubs
memcg: remove PCG_CACHE page_cgroup flag
memcg: let css_get_next() rely upon rcu_read_lock()
cgroup: revert ss_id_lock to spinlock
idr: make idr_get_next() good for rcu_read_lock()
memcg: remove unnecessary thp check in page stat accounting
memcg: remove redundant returns
memcg: enum lru_list lru
...
Change the name (and type) of a few CRC-related Boolean local
variables so they contain the word "do", to distingish their purpose
from variables used for holding an actual CRC value.
Note that in the process of doing this I identified a fairly serious
logic error in write_partial_msg_pages(): the value of "do_crc"
assigned appears to be the opposite of what it should be. No
attempt to fix this is made here; this change preserves the
erroneous behavior. The problem I found is documented here:
http://tracker.newdream.net/issues/2064
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The messenger workqueue has no need to be public. So give it static
scope.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
ceph_parse_options() takes the address of a pointer as an argument
and uses it to return the address of an allocated structure if
successful. With this interface is not evident at call sites that
the pointer is always initialized. Change the interface to return
the address instead (or a pointer-coded error code) to make the
validity of the returned pointer obvious.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Each messenger allocates a page to be used when writing zeroes
out in the event of error or other abnormal condition. Instead,
use the kernel ZERO_PAGE() for that purpose.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Add functions to allow other modules to enable or disable apple_bl. This
will be used by the gmux driver to disable apple_bl when the gmux is
present, as it is a better and more reliable option for brightness
control.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
twl4030 is using a two level irq controllers infrastruture.
So far, only the first level was using dynamic irq_desc allocation
to be able to have irq_domain support for device tree.
There is a need to allocate separate irq_descs for the SIH too to
avoid hacking the first level with interrupts from the second level.
Add an irq_base parameter to allow the caller to provide the base from
pdata or from dynamic allocation.
Affect TWL4030_NR_IRQS to the twl-core IRQs only.
Moreover that will allow the extraction of the of_node pointer for further
Device Tree conversion.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Changed the METHOD_NAME* defines that define a full pathname to
the method to METHOD_PATHNAME* in order to make it clear that
it is not a simple 4-character ACPI name. Used for the various
sleep/wake methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Version 20120215.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Simplifies the code, especially the compile-time
ACPI_REDUCED_HARDWARE option.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface allows the host to override a table via a
physical address, instead of the logical address required by
acpi_os_table_override. This simplifies the host implementation.
Initial implementation by Thomas Renninger. ACPICA implementation
creates a single function for table overrides that attempts both
a logical and a physical override.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add new notify values, add support for "hardware specific" notifies.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change expands acpi_os_read_memory and acpi_os_write_memory to a
full 64 bits. This allows 64 bit transfers via the acpi_read and
acpi_write interfaces. Note: The internal acpi_hw_read and acpi_hw_write
interfaces remain at 32 bits, because 64 bits is not needed to
access the standard ACPI registers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add ACPI_REDUCED_HARDWARE flag that removes all hardware-related
code (about 10% code, 5% static data).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These prototypes were incorrectly declared in achware.h.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds sleep and wake support for systems with these registers.
One new file, hwxfsleep.c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ST's SPEAr13xx machines are based on CortexA9 ARM processors. These
machines contain a thermal sensor for junction temperature monitoring.
This patch adds support for this thermal sensor in existing thermal
framework.
[akpm@linux-foundation.org: little code cleanup]
[akpm@linux-foundation.org: print the pointer correctly]
[viresh.kumar@st.com: thermal/spear_thermal: add compilation dependency on PLAT_SPEAR]
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the 'sb_mark_dirty()', 'sb_mark_clean()' and 'sb_is_dirty()'
helpers which are not used. I introduced them 2 years and the
intention was to make all file-systems use them in order to be able to
optimize 'sync_supers()'. However, Al Viro vetoed my patches at the
end and asked me to push superblock management down to file-systems
and get rid of the 's_dirt' flag completely, as well as kill
'sync_supers()' altogether. Thus, remove the helpers.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
Pull gfs2 changes from Steven Whitehouse.
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
GFS2: Change truncate page allocation to be GFP_NOFS
GFS2: call gfs2_write_alloc_required for each chunk
GFS2: Clean up log flush header writing
GFS2: Remove a __GFP_NOFAIL allocation
GFS2: Flush pending glock work when evicting an inode
GFS2: make sure rgrps are up to date in func gfs2_blk2rgrpd
GFS2: Eliminate sd_rindex_mutex
GFS2: Unlock rindex mutex on glock error
GFS2: Make bd_cmp() static
GFS2: Sort the ordered write list
GFS2: FITRIM ioctl support
GFS2: Move two functions from log.c to lops.c
GFS2: glock statistics gathering
These macros will be used in a later patch, where all usages are expected
to be optimized away without #ifdef CONFIG_TRANSPARENT_HUGEPAGE. But to
detect unexpected usages, we convert the existing BUG() to BUILD_BUG().
[akpm@linux-foundation.org: fix build in mm/pgtable-generic.c]
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mem_cgroup_begin_update_page_stat() should be very fast because it's
called very frequently. Now, it needs to look up page_cgroup and its
memcg....this is slow.
This patch adds a global variable to check "any memcg is moving or not".
With this, the caller doesn't need to visit page_cgroup and memcg.
Here is a test result. A test program makes page faults onto a file,
MAP_SHARED and makes each page's page_mapcount(page) > 1, and free the
range by madvise() and page fault again. This program causes 26214400
times of page fault onto a file(size was 1G.) and shows shows the cost of
mem_cgroup_begin_update_page_stat().
Before this patch for mem_cgroup_begin_update_page_stat()
[kamezawa@bluextal test]$ time ./mmap 1G
real 0m21.765s
user 0m5.999s
sys 0m15.434s
27.46% mmap mmap [.] reader
21.15% mmap [kernel.kallsyms] [k] page_fault
9.17% mmap [kernel.kallsyms] [k] filemap_fault
2.96% mmap [kernel.kallsyms] [k] __do_fault
2.83% mmap [kernel.kallsyms] [k] __mem_cgroup_begin_update_page_stat
After this patch
[root@bluextal test]# time ./mmap 1G
real 0m21.373s
user 0m6.113s
sys 0m15.016s
In usual path, calls to __mem_cgroup_begin_update_page_stat() goes away.
Note: we may be able to remove this optimization in future if
we can get pointer to memcg directly from struct page.
[akpm@linux-foundation.org: don't return a void]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Greg Thelen <gthelen@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ying Han <yinghan@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the new lock scheme for updating memcg's page stat, we don't need a
flag PCG_FILE_MAPPED which was duplicated information of page_mapped().
[hughd@google.com: cosmetic fix]
[hughd@google.com: add comment to MEM_CGROUP_CHARGE_TYPE_MAPPED case in __mem_cgroup_uncharge_common()]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Greg Thelen <gthelen@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ying Han <yinghan@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now, page-stat-per-memcg is recorded into per page_cgroup flag by
duplicating page's status into the flag. The reason is that memcg has a
feature to move a page from a group to another group and we have race
between "move" and "page stat accounting",
Under current logic, assume CPU-A and CPU-B. CPU-A does "move" and CPU-B
does "page stat accounting".
When CPU-A goes 1st,
CPU-A CPU-B
update "struct page" info.
move_lock_mem_cgroup(memcg)
see pc->flags
copy page stat to new group
overwrite pc->mem_cgroup.
move_unlock_mem_cgroup(memcg)
move_lock_mem_cgroup(mem)
set pc->flags
update page stat accounting
move_unlock_mem_cgroup(mem)
stat accounting is guarded by move_lock_mem_cgroup() and "move" logic
(CPU-A) doesn't see changes in "struct page" information.
But it's costly to have the same information both in 'struct page' and
'struct page_cgroup'. And, there is a potential problem.
For example, assume we have PG_dirty accounting in memcg.
PG_..is a flag for struct page.
PCG_ is a flag for struct page_cgroup.
(This is just an example. The same problem can be found in any
kind of page stat accounting.)
CPU-A CPU-B
TestSet PG_dirty
(delay) TestClear PG_dirty
if (TestClear(PCG_dirty))
memcg->nr_dirty--
if (TestSet(PCG_dirty))
memcg->nr_dirty++
Here, memcg->nr_dirty = +1, this is wrong. This race was reported by Greg
Thelen <gthelen@google.com>. Now, only FILE_MAPPED is supported but
fortunately, it's serialized by page table lock and this is not real bug,
_now_,
If this potential problem is caused by having duplicated information in
struct page and struct page_cgroup, we may be able to fix this by using
original 'struct page' information. But we'll have a problem in "move
account"
Assume we use only PG_dirty.
CPU-A CPU-B
TestSet PG_dirty
(delay) move_lock_mem_cgroup()
if (PageDirty(page))
new_memcg->nr_dirty++
pc->mem_cgroup = new_memcg;
move_unlock_mem_cgroup()
move_lock_mem_cgroup()
memcg = pc->mem_cgroup
new_memcg->nr_dirty++
accounting information may be double-counted. This was original reason to
have PCG_xxx flags but it seems PCG_xxx has another problem.
I think we need a bigger lock as
move_lock_mem_cgroup(page)
TestSetPageDirty(page)
update page stats (without any checks)
move_unlock_mem_cgroup(page)
This fixes both of problems and we don't have to duplicate page flag into
page_cgroup. Please note: move_lock_mem_cgroup() is held only when there
are possibility of "account move" under the system. So, in most path,
status update will go without atomic locks.
This patch introduces mem_cgroup_begin_update_page_stat() and
mem_cgroup_end_update_page_stat() both should be called at modifying
'struct page' information if memcg takes care of it. as
mem_cgroup_begin_update_page_stat()
modify page information
mem_cgroup_update_page_stat()
=> never check any 'struct page' info, just update counters.
mem_cgroup_end_update_page_stat().
This patch is slow because we need to call begin_update_page_stat()/
end_update_page_stat() regardless of accounted will be changed or not. A
following patch adds an easy optimization and reduces the cost.
[akpm@linux-foundation.org: s/lock/locked/]
[hughd@google.com: fix deadlock by avoiding stat lock when anon]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Greg Thelen <gthelen@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ying Han <yinghan@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCG_MOVE_LOCK is used for bit spinlock to avoid race between overwriting
pc->mem_cgroup and page statistics accounting per memcg. This lock helps
to avoid the race but the race is very rare because moving tasks between
cgroup is not a usual job. So, it seems using 1bit per page is too
costly.
This patch changes this lock as per-memcg spinlock and removes
PCG_MOVE_LOCK.
If smaller lock is required, we'll be able to add some hashes but I'd like
to start from this.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Greg Thelen <gthelen@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ying Han <yinghan@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We record 'the page is cache' with the PCG_CACHE bit in page_cgroup.
Here, "CACHE" means anonymous user pages (and SwapCache). This doesn't
include shmem.
Considering callers, at charge/uncharge, the caller should know what the
page is and we don't need to record it by using one bit per page.
This patch removes PCG_CACHE bit and make callers of
mem_cgroup_charge_statistics() to specify what the page is.
About page migration: Mapping of the used page is not touched during migra
tion (see page_remove_rmap) so we can rely on it and push the correct
charge type down to __mem_cgroup_uncharge_common from end_migration for
unused page. The force flag was misleading was abused for skipping the
needless page_mapped() / PageCgroupMigration() check, as we know the
unused page is no longer mapped and cleared the migration flag just a few
lines up. But doing the checks is no biggie and it's not worth adding
another flag just to skip them.
[akpm@linux-foundation.org: checkpatch fixes]
[hughd@google.com: fix PageAnon uncharging]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c1e2ee2dc4 ("memcg: replace ss->id_lock with a rwlock") has now
been seen to cause the unfair behavior we should have expected from
converting a spinlock to an rwlock: softlockup in cgroup_mkdir(), whose
get_new_cssid() is waiting for the wlock, while there are 19 tasks using
the rlock in css_get_next() to get on with their memcg workload (in an
artificial test, admittedly). Yet lib/idr.c was made suitable for RCU
way back: revert that commit, restoring ss->id_lock to a spinlock.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add_from_early_node_map() is unused.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vipin Kumar
Mike Dunn
Bastian Hecht
Shiraz Hashim
Huang Shijie
Artem Bityutskiy
Brian Norris
Alexander Stein
Jean Delvare
Anton Vorontsov
Arun Murthy
Bruce E. Robertson
Kim, Milo
Ramakrishna Pallala
Jeff Layton
J. Bruce Fields
Ingo Molnar
Sumit Semwal
Daniel Vetter
Rob Clark
Dave Airlie
Steven Rostedt
Pawel Moll
Rusty Russell
Shashidhar Hiremath
Saugata Das
Russell King
Rob Herring
Eric Dumazet
Linus Torvalds
Arnd Bergmann
Jiri Olsa
KAMEZAWA Hiroyuki
Jason Baron
Oleg Nesterov
Denys Vlasenko
Hans Verkuil
Darrick J. Wong
Joe Perches
Akinobu Mita
Lennart Poettering
Jan Beulich
Bobby Powers
Cong Wang
Muthu Kumar
Cesar Eduardo Barros
Raghavendra K T
Peter Zijlstra
John Stultz
Pablo Neira Ayuso
Joerg Roedel
Alex Elder
Seth Forshee
Benoit Cousson
Bob Moore
Len Brown
Vincenzo Frascino
Naoya Horiguchi
Konstantin Khlebnikov
Hugh Dickins
Kautuk Consul