Граф коммитов

6629 Коммитов

Автор SHA1 Сообщение Дата
Miquel Raynal f4531b2b19 mtd: rawnand: prepare the removal of ONFI/JEDEC parameter pages
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.

To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 10:46:35 +01:00
Miquel Raynal 107b7d6a7a mtd: rawnand: avoid setting again the timings to mode 0 after a reset
After a nand_reset_data_interface(), both the NAND chip and the NAND
controller use timing mode 0. The previously defined data interface for
this chip has been saved and is supposed to be restored after that.
However, if the saved data interface also refers to timing mode 0, there
is no need to re-apply them again.

Also, as nand_setup_data_interface() uses ->set/get_features(), it could
lead to issues when doing the reset at probe time as the parameter page
is not available yet to know if these functions are supported or not.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:51:01 +01:00
Miquel Raynal 415ae78ffb mtd: rawnand: check ONFI timings have been acked by the chip
Choosing ONFI timings when ->set/get_features() calls are supported
by the NAND chip is a matter of reading the chip's ONFI parameter page
and telling the chip the chosen mode (between all of the supported ones)
with ->set_feature().

Add a check on whether the chip "acked" the timing mode or not.

This can be a problem for NAND chips that do not follow entirely the
ONFI specification. These chips actually support other modes than
"mode 0", but either:
1/ do not update the timing mode register once a timing mode has been
   selected.
or
2/ do not support the TIMING_MODE featured and thus do not require users
   to change the timing mode at all.

These issues will be addressed in another patch that will add the
feature to overwrite NAND chips features within the parameter page, from
the NAND chip driver.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:49:41 +01:00
Miquel Raynal 29714d6bd7 mtd: rawnand: move calls to ->select_chip() in nand_setup_data_interface()
After a ->set_features(TIMINGS), the chip is supposed to be working at a
new speed. In order for all the transactions to be perperly handled, the
NAND controller should also be configured to this same speed. Calling
->setup_data_interface() is not enough and the chip should be
de-asserted/re-asserted through calls to ->select_chip().

Prepare the next change in nand_setup_data_interface() where timings
will be checked after being applied. Because assertions of the CS pin
will be needed from within this function, move the calls to
->select_chip() inside nand_setup_data_interface() for later
consistency.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:49:11 +01:00
Miquel Raynal 939da44758 mtd: rawnand: mxc: remove useless checks in GET/SET_FEATURES functions
All the calls to the chip's hooks ->get/set_features() go through
the core's wrappers nand_get/set_features() that already do the
necessary checks about feature support. Remove these
checks from the mxc's functions.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:48:45 +01:00
Miquel Raynal 993447b746 mtd: rawnand: handle differently chip/controller errors about timings
Usually, the source of the error when setting/getting features does not
matter (if the controller does not support sending the command or if
the chip does not support the operation).

When it comes to timings, if the controller fails it is an error while
if the chip does not support the operation, it can be silently supposed
that it already works with the maximum supported timings.

Introduce some logic in nand_setup_data_interface() to handle that
difference.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:47:46 +01:00
Miquel Raynal 97baea1e6b mtd: rawnand: use wrappers to call onfi GET/SET_FEATURES
Prepare the fact that some features managed by GET/SET_FEATURES could be
overloaded by vendor code. To handle this logic, use new wrappers
instead of directly call the ->get/set_features() hooks.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:46:02 +01:00
Miquel Raynal b958758e68 mtd: rawnand: rename SET/GET FEATURES related functions
SET/GET FEATURES are flagged ONFI-compliant because of their name. This
is not accurate as non-ONFI NAND chips support it and use it.

Rename the hooks and helpers to remove the "onfi" prefix.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:33:22 +01:00
Miquel Raynal fc2f30a4b4 mtd: rawnand: rename default ->onfi_get/set_features() implementations
Prepare future work on the ->onfi_get/set_features() hooks by renaming
the core's implementation as 'default' ones.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-20 09:33:20 +01:00
Miquel Raynal daf9a874c9 mtd: rawnand: makes the Kconfig entry clear when it comes to raw NANDs
Files have been moved in the NAND subsystem to reflect the different
flavors of NAND devices.

Raw/Parallel NAND devices have been moved to a "raw" subdirectory to
make the difference with OneNAND and SPI NAND for instance. So adjust
the Kconfig entry to clarify things.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-19 10:53:59 +01:00
OuYang ZhiZhong 6de564939e mtdchar: fix usage of mtd_ooblayout_ecc()
Section was not properly computed. The value of OOB region definition is
always ECC section 0 information in the OOB area, but we want to get all
the ECC bytes information, so we should call
mtd_ooblayout_ecc(mtd, section++, &oobregion) until it returns -ERANGE.

Fixes: c2b78452a9 ("mtd: use mtd_ooblayout_xxx() helpers where appropriate")
Cc: <stable@vger.kernel.org>
Signed-off-by: OuYang ZhiZhong <ouyzz@yealink.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-19 10:28:11 +01:00
Arnd Bergmann 00324da71e mtd: rawnand: remove bf5xx_nand driver
The blackfin architecture is getting removed, so this driver has
become obsolete.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-17 15:35:32 +01:00
Stefan Agner a722932a5a mtd: rawnand: vf610_nfc: support ONFI SET/GET_FEATURES commands
With the move to ->exec_op() the driver should now support ONFI
SET/GET_FEATURES commands.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-17 15:35:32 +01:00
Stefan Agner ecc40b8df5 mtd: rawnand: vf610_nfc: remove old hooks
Now that the driver is using ->exec_op(), remove the old
hooks.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-17 15:35:32 +01:00
Stefan Agner 1cbe30b0dd mtd: rawnand: vf610_nfc: make use of ->exec_op()
This reworks the driver to make use of ->exec_op() callback. The
command sequencer of the VF610 NFC aligns well with the new ops
interface.

The operations are translated to a NFC command code while filling
the necessary registers. Instead of using the special status and
read ID command codes (which require to read status/ID from
special registers instead of the regular data area) the driver
now now uses the main data buffer for all commands. This
simplifies the driver as no special casing is needed.

For control data (status byte, id bytes and parameter page) the
driver needs to reverse byte order for little endian CPUs since
the controller seems to store the bytes in big endian order in
the data buffer.

The current state seems to pass MTD tests on a Colibri VF61.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-17 15:35:31 +01:00
Boris Brezillon 8f347c4232 mtd: Unconditionally update ->fail_addr and ->addr in part_erase()
->fail_addr and ->addr can be updated no matter the result of
parent->_erase(), we just need to remove the code doing the same thing
in mtd_erase_callback() to avoid adjusting those fields twice.

Note that this can be done because all MTD users have been converted to
not pass an erase_info->callback() and are thus only taking the
->addr_fail and ->addr fields into account after part_erase() has
returned.

While we're at it, get rid of the erase_info->mtd field which was only
needed to let mtd_erase_callback() get the partition device back.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
2018-03-15 18:22:26 +01:00
Boris Brezillon 884cfd9023 mtd: Stop assuming mtd_erase() is asynchronous
None of the mtd->_erase() implementations work in an asynchronous manner,
so let's simplify MTD users that call mtd_erase(). All they need to do
is check the value returned by mtd_erase() and assume that != 0 means
failure.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
2018-03-15 18:21:07 +01:00
Boris Brezillon c585da9f5f mtd: Initialize ->fail_addr early in mtd_erase()
mtd_erase() can return an error before ->fail_addr is initialized to
MTD_FAIL_ADDR_UNKNOWN. Move this initialization at the very beginning
of the function.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
2018-03-15 17:25:05 +01:00
Antonio Cardace f0a37a8db8 mtd: st_spi_fsm: use %*ph to print small buffer
Use %*ph format to print small buffer as hex string.

Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antonio Cardace <anto.cardace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-15 17:20:37 +01:00
Colin Ian King d40a18fec0 mtd: block2mtd: remove redundant initialization of 'bdev'
Pointer bdev is being initialized however this value is never
read as bdev is assigned an updated value from the returned
call to blkdev_get_by_path.  Remove the redundant assignment.

Cleans up clang warning:
drivers/mtd/devices/block2mtd.c:228:23: warning: Value stored to
'bdev' during its initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-15 17:15:34 +01:00
Masahiro Yamada 828814e6a4 mtd: rawnand: remove STANDALONE compile mode of nand_ecc
This file can not be built independently any more.  We would have to
bring in more to resolve mtd_to_nand(mtd)->ecc.size, for example.

It is difficult to notice a breakage since nobody compiles this mode.
It is not worth fixing or maintaining in my opinion.  Remove.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-15 16:42:33 +01:00
Shreeya Patel 63fa37f0c5 mtd: rawnand: Replace printk() with appropriate pr_*() macro
Using pr_<loglevel>() is more concise than printk(KERN_<LOGLEVEL>).
Replace printks having a log level with the appropriate pr_*() macros.
Define pr_fmt() and remove other additional macros from the replaced
printks.

Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-15 15:57:05 +01:00
Boris Brezillon 26777d3721 mtd: Move onenand code base to drivers/mtd/nand/onenand
Move onenand code base to the drivers/mtd/nand directory in the hope
that someday someone will patch it to use the generic NAND helpers.
If it never happens, at least we'll have all NAND related support in a
single directory and not spread over the drivers/mtd/ directory.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-15 15:40:37 +01:00
Boris Brezillon 801492c508 mtd: onenand: Get rid of comments giving the file path inside the file itself
Some files add a comment giving the path of the file inside the Linux
tree, which is pretty useless since the reader had to find the file to
open it.

Getting rid of these comments will also allow us to easily move these
files around when needed.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-15 15:40:35 +01:00
Arnd Bergmann fdda85f696 This is the pxa changes for v4.17 cycle :
- minor changes for property API
  - clock API fix for ULPI driver warning
 
 It exceptionally contains a merge from the mtd tree from Boris
 to prevent any merge conflicts in the PXA tree.
 -----BEGIN PGP SIGNATURE-----
 
 iQJLBAABCAA1FiEExgkueSa0u8n4Ls+HA/Z63R24yxIFAlqi9CMXHHJvYmVydC5q
 YXJ6bWlrQGZyZWUuZnIACgkQA/Z63R24yxIa0g//aCllCGnEY2S5+hxtg7eCAkEg
 QKqBTpHhGUDpvix8MwWrt+089Kj5CWHknx7PWQs3YQj/XzevA5mX65szteICfDX2
 K0BJj/OsecKBTCdHjVOEerM6Yy6nKrL0gX7zzUuD81H54Dk6os2pnruZEYEIn1HD
 /YhWprLs0sDqwjPI/a9Tfqw5N3nM3uStl0hp3HDplw2AtIovL/E4CrPt9Q3CCtEy
 Qj1PtM0ON9UkrlnHnFNEh3f5bja9Lwo1v3IueSoTWw8UdyxoA3itPXo+5pHZv5GG
 H4UXan1vYSaj1ISsAnOt9YuFxEMl4+d8BfKmzrqr2CAlNAeMPJRZ66UdYTecx1FJ
 z65kxxLiBi7r1eQqvBz6PhtKndHKUbBHJjc4RVJFm8PY7fzW/6LReDnHhUYpxfB1
 K5BfzfIPjH3ex9PME370gZx6wdtaepSgeQFpo2jpCI1AXO1IFEdD0v/IkQounrUe
 fgBle5yW4qQMuG+EDDOn/aDosVx7uM4856V7JtMrhUecB8fMwZ0elCaCSnchZO/G
 mOeZUa9YXUOfFVBpKdidQzVxMQBP62zd8MFKOCOIkKUjfBC9AHRn1nLkXQak8hNt
 HjRY34YqIEzbn5+3SRJO9doTV7oXMSOTfDvsQFugalhOKgHRZo7IpkREhqWWXByw
 r7vKVVY1elTGKVVWdUQ=
 =/vgG
 -----END PGP SIGNATURE-----

Merge tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux into next/soc

Pull "This is the pxa changes for v4.17 cycle" from Robert Jarzmik:

 - minor changes for property API
 - clock API fix for ULPI driver warning

It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.

* tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux:
  ARM: pxa/raumfeld: use PROPERTY_ENTRY_U32() directly
  ARM: pxa: ulpi: fix ulpi timeout and slowpath warn
  ARM: pxa: cm-x300: remove inline directive
  ARM: pxa: fix static checker warning in pxa3xx-ulpi
  MAINTAINERS: remove entry for deleted pxa3xx_nand driver
  arm: dts: pxa: use reworked NAND controller driver
  dt-bindings: mtd: remove pxa3xx NAND controller documentation
  mtd: nand: remove useless fields from pxa3xx NAND platform data
  mtd: nand: remove deprecated pxa3xx_nand driver
  mtd: nand: use Marvell reworked NAND controller driver with all platforms
2018-03-12 15:27:14 +01:00
Bart Van Assche 8b904b5b6b block: Use blk_queue_flag_*() in drivers instead of queue_flag_*()
This patch has been generated as follows:

for verb in set_unlocked clear_unlocked set clear; do
  replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
    $(git grep -lw queue_flag_${verb} drivers block/bsg*)
done

Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.

Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-03-08 14:13:48 -07:00
Boris Brezillon 3383fb35c9 Remove the pxa3xx_nand driver (replaced by marvell_nand).
-----BEGIN PGP SIGNATURE-----
 
 iQI5BAABCAAjBQJamceNHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
 Ze02AX4ItwAkoxAAtdrbc5so/m0ZgPxVkoPl+d3cO+1KveG+OD4kvydieuKZmfGx
 htfayfAG47GsutoN5yXEeuCh5BLkhGsjaBFPO9RhxZM+dZUPl2s3Dp7H/m5xMkaA
 DrYMZ2AQE+Ll4YUaAFE7CIZ9dOwXjHG4rI2wAPRZ+tjs6okmiTP7luYnn4kGwqbC
 qgEmpjxawWl+LwujJqu4ilz4HLe/1zmE7BxGUeUqhyUXnwfgtVTmZVglMKPambZt
 i5Qqom3NOY2qXXdc/ONsYhdwUwLeR1v5Sz0FJw2vpxKKpXPl18SCmxzVuefOxvix
 n6Z0BnKTt+vSPMAZuGkkvr559/jHNT5EQnN5K7TXzl5V4K84HSUWhXHNi4SwZce+
 ASTgOPJUvq/h0Mwo9nC+c7XUQnZ1FjYOY981gDs8XyM5WdA4TpN4TJmhgzUQX59q
 +Ui+vQ+0FVNIXmqZ+qqxnZ/wRVzlPgCDTLKLl4goZ+u9EU2LXvkeoOz0k1mEQ1Pd
 ehSfFZSdfSKkXxzb52R3JV6ELZ9POh66u2abf35mWIgC+l1gApFWpqIdIb3i/Wko
 ALuaLu3k9SnrZgiEuJy9yQ/qKD6pydyfpM2YgO/XEhtRxDlamLWOMyLmgcA1Z/gM
 oYhr5v3leNu3Dyd3RWLQXFRMe1qmUugmxvvbNyh8BhX9r2PmUhuiTdcFf6U=
 =bovT
 -----END PGP SIGNATURE-----

Merge tag 'nand/pxa3xx-removal' of git://git.infradead.org/linux-mtd into nand/next

Remove the pxa3xx_nand driver (replaced by marvell_nand).
2018-03-02 22:57:43 +01:00
Miquel Raynal 7576594c8e mtd: nand: remove useless fields from pxa3xx NAND platform data
The "enable arbiter" bit is available only for pxa3xx based platforms
but it was experimentally shown that even if this bit is reserved,
some Marvell platforms (64-bit) actually need it to be set. The driver
always set this bit regardless of this property, which is harmless.
Then this property is not needed.

The "num_cs" field is always 1 and for a good reason, the old driver
(pxa3xx_nand.c) could only handle one. The new driver that replaces it
(marvell_nand.c) can handle more, but better use device tree for such
description. As there is only one available chip select, there is no
need for an array of partitions neither an array of partition numbers.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-02 21:51:41 +01:00
Miquel Raynal cc396436c2 mtd: nand: remove deprecated pxa3xx_nand driver
All board files and defconfig files have been moved to use the new
marvell_nand driver instead of pxa3xx_nand, so we can safely remove this
file now. People should use the new driver which is supposed to behave
exactly like the old one.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-23 22:00:18 +01:00
Miquel Raynal 4da712e702 mtd: nand: fsmc: use ->exec_op()
Remove the deprecated ->cmd_ctrl() implementation to use ->exec_op() in
the fsmc_nand driver.

Implement the ->select_chip() hook to avoid having to support the hack
from the core that send a NAND_CMD_NONE with NAND_NCE to signal a
deassertion of nCE.

Also get rid of the last references to ->IO_ADDR_[R|W] that are not used
anymore.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-17 09:29:50 +01:00
Miquel Raynal 4df6ed4f0a mtd: nand: fsmc: get rid of IO_ADDR_[R|W]
Remove the use of IO_ADDR_[R|W] in the fsmc_nand driver. Instead, use a
pointer to the control registers to avoid doing several arithmetic
operations (including a multiplication) each time a control register is
read or written.

All references to IO_ADDR_[R|W] are not entirely removed from the driver
as, at this time, these values are needed by the NAND core in the
default ->read/write_byte/word() hooks. These references will be
entirely removed when switching to ->exec_op(), that does not make use
of these hooks anymore.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-17 09:25:46 +01:00
Boris Brezillon 9c3736a3de mtd: nand: Add core infrastructure to deal with NAND devices
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-16 10:10:53 +01:00
Boris Brezillon 93db446a42 mtd: nand: move raw NAND related code to the raw/ subdir
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-16 10:09:34 +01:00
Boris Brezillon 7b6afee729 mtd: nand: Add missing copyright information
Some drivers have been derived from others which have then been removed
from the source tree. When this is the case, add mention the copyright
of the source file(s) they've been derived from.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-16 10:09:24 +01:00
Boris Brezillon 187c54488e mtd: nand: State when references to other drivers are no longer valid
A lot of NAND drivers have been derived from other old NAND drivers
which have since then been removed from the Linux tree. When this is
the case, specify when the file the header is referring to has been
removed so that people can find the original implementation more
easily.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-16 10:09:16 +01:00
Boris Brezillon e36f2eb6ca mtd: nand: ams-delta: Fix path to toto.c source file
Last known location of toto.c was drivers/mtd/nand/toto.c. Fix the
path so that one can use git log to find when the driver was deleted
and possibly checkout the source code.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-16 10:09:02 +01:00
Boris Brezillon 93cbd6f354 mtd: nand: Stop using full path when referring to files placed in the same dir
Some NAND drivers are derived from other NAND drivers and state it in
their license header. Using full path to point to other driver files
sitting in the same directory is not such a good idea, since the NAND
drivers might be moved to a different directory at some point, and we
don't to patch all license/copyright headers everytime this happen.

The only exception where we keep full path is when the referred source
files no longer exist in the tree.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-16 10:08:50 +01:00
Boris Brezillon 43a0a45abc mtd: nand: Get rid of comments giving the file path inside the file itself
Some files add a comment giving the path of the file inside the Linux
tree, which is pretty useless since the reader had to find the file to
open it.

Getting rid of these comments will also allow us to easily move these
files around when needed.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-16 10:08:27 +01:00
KOBAYASHI Yoshitake fb3bff5b40 mtd: nand: toshiba: Retrieve ECC requirements from extended ID
This patch enables support to read the ECC strength and size from the
NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
based on the information of the 6th ID byte of the Toshiba Memory SLC
NAND.

Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-14 20:28:29 +01:00
Alexey Khoroshilov 1b8c90985f mtd: nand: vf610: check mtd_device_register() return code
vf610_nfc_probe() misses error handling of mtd_device_register().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:05 +01:00
Alexey Khoroshilov 196644fd09 mtd: nand: vf610: improve readability of error label
Use clearer error labels as Boris Brezillon suggested.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:05 +01:00
Alexey Khoroshilov f5a666bdd5 mtd: nand: vf610: remove the unnecessary of_node_put()
Calling of_node_put() in vf610_nfc_probe() is wrong because nothing in
this code retains a reference to the DT node.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:04 +01:00
Stefan Agner 532a1cf9a0 mtd: nand: vf610_nfc: remove unused function
The function count_written_bits has been replaced by the generic
nand_check_erased_ecc_chunk() function with commit 48c25cf441
("mtd: nand: vf610_nfc: use nand_check_erased_ecc_chunk() helper").
Remove the unused function.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:04 +01:00
Miquel Raynal 07ad5a7214 mtd: nand: add ->setup_data_interface() support for Marvell NFCv1
First generation of Marvell NAND flash controllers (eg. embedded in PXA
boards) did not make use of the NAND core hook ->setup_data_interface()
to setup controller timings. Add support for it.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:36:03 +01:00
Sascha Hauer 68dc8e41fd mtd: nand: mxc: remove now unused code
Since we now have our own read_page/write_page functions
mxc_nand_command() will no longer be called with NAND_CMD_READ0,
NAND_CMD_READOOB, NAND_CMD_SEQIN and NAND_CMD_PAGEPROG. Remove
the code handling these commands.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:58 +01:00
Sascha Hauer cd8b465533 mtd: nand: mxc: Drop now unnecessary functions
Since we have our own read_page/write_page functions correct_data and
calculate are no longer needed. Remove them.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:51 +01:00
Sascha Hauer 6811c4642a mtd: nand: mxc: Add own write_page
Now that we have our own read_page function add a write_page function
for consistency aswell. This can be a lot easier than the generic
function since we do not have to iterate over subpages but can write
the whole page at once. Also add write_page_raw and write_oob for
proper raw and oob write support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:45 +01:00
Sascha Hauer 5039fc9f2d mtd: nand: mxc: Fix failed/corrected values for v1 controllers
The v1 controller code has several flaws:
- We do not forward the number of corrected bitflips to the upper layers
- For 2k page NAND chips only the status results from the fourth subpage
  read are evaluated, so ECC failures in the other subpages remain
  uncovered
- When there are uncorrectable errors we have to increase the statistics
  counter, but still have to return successfully. Currently we return
  an error

This patch fixes this by introducing a v1 specific read_page function.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:38 +01:00
Sascha Hauer 67b87f66ca mtd: nand: mxc: Fix failed/corrected values for v2/v3 controllers
Currently nand_read_page_hwecc() from nand_base calls
mxc_nand_correct_data_v2_v3() for each subpage, but in this function we
return the corrected/failed results for the whole page instead
of a single subpage. On a 2k page size Nand this leads to results which
are 4 times too high.
The whole ecc.calculate/ecc.correct mechanism used by
nand_read_page_hwecc() is not suitable for devices which correct the
data in hardware, so fix this by using a driver specific read_page
function which does the right thing. Also add read_page_raw and read_oob
For proper raw and oob read support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:34 +01:00
Sascha Hauer 1af0b31474 mtd: nand: mxc: Add buffer argument to copy_spare
With following patches we will have to copy the spare data to/from
other buffers, so add the buffer as argument to copy_spare().

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:28 +01:00
Sascha Hauer 040bd3f6a3 mtd: nand: mxc: Add function to control hardware ECC
For proper raw read/write support need to be able to control the
hardware ECC engine. Add a function to enable/disable it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:24 +01:00
Sascha Hauer 1549333167 mtd: nand: mxc: reorder functions to avoid forward declarations
We'll call copy_spare() and mxc_do_addr_cycle() from another place
during the next patches, so move functions up to avoid forward
declarations.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 23:35:04 +01:00
Rafał Miłecki 0dbe4ea78d mtd: get rid of the mtd_add_device_partitions()
This simplifies code a bit by:
1) Avoiding an extra (tiny) function
2) Checking for amount of parsed (found) partitions just once
3) Avoiding clearing/filling struct mtd_partitions manually

With this commit proper functions are called directly from the
mtd_device_parse_register(). It doesn't need to use minor tricks like
memsetting struct to 0 to trigger an expected
mtd_add_device_partitions() behavior.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 13:39:20 +01:00
Rafał Miłecki 2c77c57d22 mtd: move code adding master MTD out of mtd_add_device_partitions()
This change is a small cleanup of mtd_device_parse_register(). When
using MTD_PARTITIONED_MASTER it makes sure a master MTD is registered
before dealing with partitions. The advantage of this is not mixing
code handling master MTD with code handling partitions.

This commit doesn't change any behavior except from a slightly different
failure code path. The new code may need to call del_mtd_device when
something goes wrong.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 13:39:20 +01:00
Boris Brezillon e6e620f0e1 mtd: Make sure the device supports erase operations in mtd_erase()
Some devices do not implement ->_erase() or have an invalid ->erasesize
value. In this case, mtd_erase() should return -ENOTSUPP.

Note that the test is not done on the MTD_NO_ERASE flag because this
flag means 'erasing a block before writing to it is unnecessary',
not 'the erase operation is not supported'. Actually, some drivers are
setting the MTD_NO_ERASE flag but still implementing the ->_erase()
hook and setting a valid ->erasesize value.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 11:46:38 +01:00
Geert Uytterhoeven f23def8038 mtd: nand: MTD_NAND_MARVELL should depend on HAS_DMA
If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/mtd/nand/marvell_nand.ko] undefined!

Add a dependency on HAS_DMA to fix this.

Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 10:57:20 +01:00
Stefan Agner ea56fb2823 mtd: nand: vf610: set correct ooblayout
With commit 3cf32d1802 ("mtd: nand: vf610: switch to
mtd_ooblayout_ops") the driver started to use the NAND cores
default large page ooblayout. However, shortly after commit
6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
changed the default layout to the old hamming layout, which is
not what vf610_nfc is using. Specify the default large page
layout explicitly.

Fixes: 6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-02-12 10:56:36 +01:00
Linus Torvalds 2382dc9a3e dma mapping changes for Linux 4.16:
This pull requests contains a consolidation of the generic no-IOMMU code,
 a well as the glue code for swiotlb.  All the code is based on the x86
 implementation with hooks to allow all architectures that aren't cache
 coherent to use it.  The x86 conversion itself has been deferred because
 the x86 maintainers were a little busy in the last months.
 -----BEGIN PGP SIGNATURE-----
 
 iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlpxcVoLHGhjaEBsc3Qu
 ZGUACgkQD55TZVIEUYN/Lw/+Je9teM4NPQ8lU/ncbJN/bUzCFGJ6dFt2eVX/6xs3
 sfl8vBdeHt6CBM02rRNecEr31z3+orjQes5JnlEJFYeG3jumV0zCPw/zbxqjzbJ1
 3n6cckLxbxzy8Ca1G/BVjHLAUX5eWp1ujn/Q4d03VKVQZhJvFYlqDbP3TrNVx7xn
 k86u37p/o+ngjwX66UdZ3C4iIBF8zqy6n2kkpv4HUQtHHzPwEvliN39eNilovb56
 iGOzjDX1UWHAu4xCTVnPHSG4fA4XU41NWzIN3DIVPE25lYSISSl9TFAdR8GeZA0G
 0Yj6sW53pRSoUwco1ocoS44/FgrPOB5/vHIL06pABvicXBiomje1QylqcK7zAczk
 esjkfPEZrmZuu99GtqFyDNKEvKKdy+aBGaTZ3y+NxsuBs+0xS2Owz1IE4Tk28xaw
 xh7zn+CVdk2fJh6ZIdw5Eu9b9VN08UriqDmDzO/ylDlcNGcDi7wcxiSTEkHJ1ON/
 g9nletV6f3egL0wljDcOnhCJCHTvmWEeq3z8lE55QzPzSH0hHpnGQ2WD0tKrroxz
 kjOZp0TdXa4F5iysOHe2xl2sftOH0zIkBQJ+oBcK12mTaLu21+yeuCggQXJ/CBdk
 1Ol7l9g9T0TDuZPfiTHt5+6jmECQs92LElWA8x7uF7Fpix3BpnafWaaSMSsosF3F
 D1Y=
 =Nrl9
 -----END PGP SIGNATURE-----

Merge tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping

Pull dma mapping updates from Christoph Hellwig:
 "Except for a runtime warning fix from Christian this is all about
  consolidation of the generic no-IOMMU code, a well as the glue code
  for swiotlb.

  All the code is based on the x86 implementation with hooks to allow
  all architectures that aren't cache coherent to use it.

  The x86 conversion itself has been deferred because the x86
  maintainers were a little busy in the last months"

* tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping: (57 commits)
  MAINTAINERS: add the iommu list for swiotlb and xen-swiotlb
  arm64: use swiotlb_alloc and swiotlb_free
  arm64: replace ZONE_DMA with ZONE_DMA32
  mips: use swiotlb_{alloc,free}
  mips/netlogic: remove swiotlb support
  tile: use generic swiotlb_ops
  tile: replace ZONE_DMA with ZONE_DMA32
  unicore32: use generic swiotlb_ops
  ia64: remove an ifdef around the content of pci-dma.c
  ia64: clean up swiotlb support
  ia64: use generic swiotlb_ops
  ia64: replace ZONE_DMA with ZONE_DMA32
  swiotlb: remove various exports
  swiotlb: refactor coherent buffer allocation
  swiotlb: refactor coherent buffer freeing
  swiotlb: wire up ->dma_supported in swiotlb_dma_ops
  swiotlb: add common swiotlb_map_ops
  swiotlb: rename swiotlb_free to swiotlb_exit
  x86: rename swiotlb_dma_ops
  powerpc: rename swiotlb_dma_ops
  ...
2018-01-31 11:32:27 -08:00
Linus Torvalds d1de762e36 This pull request contains updates for both UBI and UBIFS:
- Usage of new fscrypt APIs
 - A fix for a Fastmap issue
 - Other minor bug fixes
 -----BEGIN PGP SIGNATURE-----
 
 iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAlpl68kWHHJpY2hhcmRA
 c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wX3vEADXb7aCdL87y5FxML3UTpGHoIU8
 TYTO58WsWdBV32WbROq0F3c6QADYnJt3+oZuCsSYIwqZP2+7rry4Jg8K39F5JDS6
 UxQYUoKLtAoCdou9AQfE4ilFIONbZSdSDnB7Dsc/UQiLKaFtZhGZBSocwAmA5moe
 8Jp6uhhbr91CrVwhek/+PJxdzoBoj2DAW3/kH7z6VD6klY5nS9t7AJobxHE5eKO1
 nv1Fc1y1Q8E22KuJ7SuBFny/k2BXl0jPbl898+yw0vThqV2QHmha9uM7Tk70Ek1/
 pRQJUiJ8ljxeix5oKCNjbirvdN4TgHWCZAg4YNOoxDYTNzGIMGfXjUojlnUO3hAp
 WLDFo5nOxL8C/ak7quql49/JtSbN/6esBZqOnZh60kvA9LOngggPOBonBrJ93+Vc
 ui6VdJN69Og7Efb8UlOYCONUl70rT7EupZqjPLNKkQp2jGCE683szFtDFkNBlcnn
 fQKnp8IOpWanw2A1z5EtPlfJaFUk2tj0CbgOWgyVb8bkIvqH1d9H67o12DrODFsr
 LGe1icv+jy4qyc76XO79EMyitOObsa6n5j9bfe0fuECJZMBcp/cWlcVusrSQJ+KN
 Onyhi8O4sMeWVbED+N5Xb+ozdnrnls2Urb1L3+GCDdKlSKlgsXGDreLiLaNuQJs0
 peYomh6Wl3urHERflg==
 =+cCd
 -----END PGP SIGNATURE-----

Merge tag 'upstream-4.16-rc1' of git://git.infradead.org/linux-ubifs

Pull UBI/UBIFS updates from Richard Weinberger:

 - use the new fscrypt APIs

 - a fix for a Fastmap issue

 - other minor bug fixes

* tag 'upstream-4.16-rc1' of git://git.infradead.org/linux-ubifs:
  ubi: block: Fix locking for idr_alloc/idr_remove
  mtd: ubi: wl: Fix error return code in ubi_wl_init()
  ubi: Fix copy/paste error in function documentation
  ubi: Fastmap: Fix typo
  ubifs: remove error message in ubifs_xattr_get
  ubi: fastmap: Erase outdated anchor PEBs during attach
  ubifs: switch to fscrypt_prepare_setattr()
  ubifs: switch to fscrypt_prepare_lookup()
  ubifs: switch to fscrypt_prepare_rename()
  ubifs: switch to fscrypt_prepare_link()
  ubifs: switch to fscrypt_file_open()
  ubi: fastmap: Clean up the initialization of pointer p
  ubi: fastmap: Use kmem_cache_free to deallocate memory
  ubi: Fix race condition between ubi volume creation and udev
  mtd: ubi: Use 'max_bad_blocks' to compute bad_peb_limit if available
  ubifs: Fix uninitialized variable in search_dh_cookie()
2018-01-29 13:31:47 -08:00
Linus Torvalds 0fc7e74663 MTD changes:
Core changes:
   * Rework core functions to avoid duplicating generic checks in
     NAND/OneNAND sub-layers
   * Update the MAINTAINERS entry to reflect the fact that MTD
     maintainers now use a single git tree
 
   Driver changes:
   * CFI: use macros instead of inline functions to limit stack
     usage and make KASAN happy
 
 NAND changes:
   Core changes:
   * Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
   * Introduce the ->exec_op() infrastructure
   * Rework NAND buffers handling
   * Fix ECC requirements for K9F4G08U0D
   * Fix nand_do_read_oob() to return the number of bitflips
   * Mark K9F1G08U0E as not supporting subpage writes
 
   Driver changes:
   * MTK: Rework the driver to support new IP versions
   * OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
     DT support
   * Marvell: Add a new driver to replace the pxa3xx one
 
 SPI NOR changes:
   Core changes:
   * Add support to new ISSI and Cypress/Spansion memory parts.
   * Fix support of Micron memories by checking error bits in the FSR.
   * Fix update of block-protection bits by reading back the SR.
   * Restore the internal state of the SPI flash memory when removing the
     device.
 
   Driver changes:
   * Maintenance for Freescale, Intel and Metiatek drivers.
   * Add support of the direct access mode for the Cadence QSPI controller.
 -----BEGIN PGP SIGNATURE-----
 
 iQJABAABCAAqBQJabumAIxxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
 Y29tAAoJEGXtNgF+CLcA0eAP/1s4u/Vs0RaDL2Jog0z+3fdx9HKYTK01hiQoe5Vf
 0ouGH0lR9usAmmJlXxxNpBHFvJxsofJoCNaciHAiydCMBpX6oAQMYMMcPs4Qo7C/
 vydLBDBmKZNyQ9dv6FbjP+3Y/5drIGF+VfxXZwhGA3lwP5CSVbB9ndI8+A5bScIV
 m2RMOA/lorbNHQahEkt7FHd92yQxBXlbhHBf5Foy2dGhO3rpTWzL/d1KPAkcfeli
 ehjfazkbuwFxGlYBFsrWxsnm0zqrqIWtdTE5/0i8iC1FfbxL5KjRnAFg8AsXIepn
 C2rCAxM/890mIFypT/8xhu+1u8+Bmb1r/pA9G+f3zpkiAHcUGC3eMO3IhX/jkcAd
 jCD/zeaSW8uHrBoJA6mGhO1tkBA97w15XCQC38UZkRMaJsY8Rv50ST4afA4in7mi
 bdRnpOOBYsBv9LvLm+FzQ0EgRQl642mFY8rae+gAjkF/zt8zGHSt6UNgtwMRxqZJ
 ns/TyhNm7roYV3cPpAgOWK//9XAGII9YZ6x9XmPNZLq62yf+zqJnfeuy7bXATRfG
 GGYk6wd+VdN+Ax2mqVKEJMCArjz0kLAHOtpIwv2/RxB1dlNMdugaDPUcqFteZbXh
 wlgORLXLqZ8jfy+ITFB5HMDs/NMyuRr815jdPGZafHIx8xOBQD32Izv7cpYctfWU
 f2NU
 =Mxo2
 -----END PGP SIGNATURE-----

Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd

Pull MTD updates from Boris Brezillon:
 "MTD core changes:
   - Rework core functions to avoid duplicating generic checks in
     NAND/OneNAND sub-layers
   - Update the MAINTAINERS entry to reflect the fact that MTD
     maintainers now use a single git tree

  MTD driver changes:
   - CFI: use macros instead of inline functions to limit stack usage
     and make KASAN happy

  NAND core changes:
   - Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
   - Introduce the ->exec_op() infrastructure
   - Rework NAND buffers handling
   - Fix ECC requirements for K9F4G08U0D
   - Fix nand_do_read_oob() to return the number of bitflips
   - Mark K9F1G08U0E as not supporting subpage writes

  NAND driver changes:
   - MTK: Rework the driver to support new IP versions
   - OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
     fix DT support
   - Marvell: Add a new driver to replace the pxa3xx one

  SPI NOR core changes:
   - Add support to new ISSI and Cypress/Spansion memory parts.
   - Fix support of Micron memories by checking error bits in the FSR.
   - Fix update of block-protection bits by reading back the SR.
   - Restore the internal state of the SPI flash memory when removing
     the device.

  SPI NOR driver changes:
   - Maintenance for Freescale, Intel and Metiatek drivers.
   - Add support of the direct access mode for the Cadence QSPI
     controller"

* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
  mtd: nand: sunxi: Fix ECC strength choice
  mtd: nand: gpmi: Fix subpage reads
  mtd: nand: Fix build issues due to an anonymous union
  mtd: nand: marvell: Fix missing memory allocation modifier
  mtd: nand: marvell: remove redundant variable 'oob_len'
  mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
  mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
  mtd: Remove duplicate checks on mtd_oob_ops parameter
  mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
  mtd: mtdpart: Make ECC stat handling consistent
  mtd: onenand: omap2: print resource using %pR format string
  mtd: mtk-nor: modify functions' name more generally
  mtd: onenand: samsung: remove incorrect __iomem annotation
  MAINTAINERS: Add entry for Marvell NAND controller driver
  ARM: OMAP2+: Remove gpmc-onenand
  mtd: onenand: omap2: Configure driver from DT
  mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
  mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
  mtd: onenand: omap2: Convert to use dmaengine for memcpy
  mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
  ...
2018-01-29 11:11:56 -08:00
Boris Brezillon 571cb17b23 Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
 * Introduce the ->exec_op() infrastructure
 * Rework NAND buffers handling
 * Fix ECC requirements for K9F4G08U0D
 * Fix nand_do_read_oob() to return the number of bitflips
 * Mark K9F1G08U0E as not supporting subpage writes
 
 Driver changes:
 * MTK: Rework the driver to support new IP versions
 * OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
   DT support
 * Marvell: Add a new driver to replace the pxa3xx one
 -----BEGIN PGP SIGNATURE-----
 
 iQJABAABCAAqBQJaaawrIxxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
 Y29tAAoJEGXtNgF+CLcAApQP/3rP5nXYF5l9mMX8lDSrUDiU7EMIHOyOvIAxmNkf
 1NVIAnFumHyH08JJ1YbVDbqRDnNSgAlkSKVtbeQ/jREM25Klg8RJj95Fpy0I+2Zh
 iM8e/vDNb/jw5fcoSrQuYBOGjh6vo8XjDFjAlvw9fo13xn+J5on9bpQCwr4Qq6Zf
 RMKTjwWUSk1lGT8M7Wzb3McoBkMQhkrdzWx1mZ+o+BKSYvDc3BjzJZ/+dHgfa5Jr
 91RrHnZcx+UnOaEqRPgQ0eZK1Ww3MzHG3TIN7U1KVrV63CrJ3UmB38ZcsLQzjl2g
 2P0ntsyYV8Eu3Wv8ZX4HovcBmZyzLWlr935uQE6EQxiCX9eOJyE/ImTmC4JhBGoF
 XElIqj+mDkZHDYI/5D+Hm02+t4NgSyqIddZ5nD68LxjFmIZSjKRXKE3ovYPoi2U8
 TY4LO+zXDDGA5FcSV4DcSrKN0M0I2lL9P9/ve+rvibNM9W8p/8piWPPJUUdV1sPQ
 RHN0m0X73Ce/C4U6PE/dTA6qb3RI6UaxWrl7Qdf9Kobm60PZQme8gLP7C0ert09T
 4DnfOaOHMtqh8G+p03oQQ/CXgdi+WdnJINgkq5Auu7vyFgAJMZRmHlzowsIJ5+QA
 +cengrfRzMCfsLnFN4LraHo1Kp5zXkPYEIPTx6Mq0B1GvqdLZV49tsqM8HSeIy1r
 vXN2
 =TXIU
 -----END PGP SIGNATURE-----

Merge tag 'nand/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next

Pull NAND changes from Boris Brezillon:

"
  Core changes:
  * Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
  * Introduce the ->exec_op() infrastructure
  * Rework NAND buffers handling
  * Fix ECC requirements for K9F4G08U0D
  * Fix nand_do_read_oob() to return the number of bitflips
  * Mark K9F1G08U0E as not supporting subpage writes

  Driver changes:
  * MTK: Rework the driver to support new IP versions
  * OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
    DT support
  * Marvell: Add a new driver to replace the pxa3xx one
"
2018-01-29 09:58:36 +01:00
Boris Brezillon c8f22b02a8 This pull-request contains the following notable changes:
Core changes:
 * Add support to new ISSI and Cypress/Spansion memory parts.
 * Fix support of Micron memories by checking error bits in the FSR.
 * Fix update of block-protection bits by reading back the SR.
 * Restore the internal state of the SPI flash memory when removing the
   device.
 
 Driver changes:
 * Maintenance for Freescale, Intel and Metiatek drivers.
 * Add support of the direct access mode for the Cadence QSPI controller.
 -----BEGIN PGP SIGNATURE-----
 
 iQI4BAABCAAiBQJaW3m5GxxjeXJpbGxlLnBpdGNoZW5Ad2VkZXY0dS5mcgAKCRDn
 4OgLHRpJchNfEACxur2dlSc1WVpFSczwejXEMy9Pp/MOz+tEBuNGqZlKyjmACLXD
 C/Cn1nuWxL0DbkG09va4PM3M3pf+LysMACSIwBa0fxRKLb8uvIkTMMmCEV6Dr+Ie
 XiydtBg1vriklgGPS+ytFt5SibER8U7dj2p4+OO2feql6HxLGs/OJ3Ta3k18794K
 VDhzFvudpUTGWet3MeoTky9jMpkjxHqY/e4PFB7Q2u41a+yrsRuQkXtYkIUS3Jki
 nFagQMmhU6XvTpjDt3tpGlJ54lFEBkh2575AAPjnf4ZzII5Sdq+uwDi56DweB+qM
 1S/Ajung1YV0l1nlN48YP5n2e362tOk41F+rlRv08kutbj3bi9V6jQZ19XA260u6
 jVRhiMg5gW11MQtxvCCoePgJ8GHUAYrMPnmlTExw27Z3Ig57L+We92txG3P56+Pj
 ZgKbbL/W2qFoFD9Z4UkFGY8aXWc4Bw8gNEMBB6mICqHHtuljxVTDomRO1rUtgny5
 4k/eIBcoHhhZq9jrXTtGit4l3tXxbr26ejirQv1/ZIwYM8r+7DNJBotVa4v+AS3W
 sR+SyrOVA9//taRJl3G48gSo5i3GqUyDRMUqd5tW2Lzw14muLTcmckAz8Gn/TByN
 Wnez11AT0UkNUm4yrYWOPDlEq7mHjbnSyXUHX7XO7A9ft6Euo0LZp6WozA==
 =3oDP
 -----END PGP SIGNATURE-----

Merge tag 'spi-nor/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next

Pull spi-nor changes from Cyrille Pitchen:

"
  This pull-request contains the following notable changes:

  Core changes:
  * Add support to new ISSI and Cypress/Spansion memory parts.
  * Fix support of Micron memories by checking error bits in the FSR.
  * Fix update of block-protection bits by reading back the SR.
  * Restore the internal state of the SPI flash memory when removing the
    device.

  Driver changes:
  * Maintenance for Freescale, Intel and Metiatek drivers.
  * Add support of the direct access mode for the Cadence QSPI controller.
"
2018-01-29 09:55:14 +01:00
Miquel Raynal f4c6cd1a7f mtd: nand: sunxi: Fix ECC strength choice
When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.

For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.

Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Cc: <stable@vger.kernel.org>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-25 09:14:32 +01:00
Boris Brezillon 4c7e95b1b3 mtd: nand: gpmi: Fix subpage reads
Commit 25f815f66a ("mtd: nand: force drivers to explicitly send
READ/PROG commands") added a call to nand_read_page_op() in
gpmi_ecc_read_page(), which means this function now sends a READ0
command and place the data pointer at the beginning of the page. This
logic is breaking gpmi_ecc_read_subpage() which was calling
gpmi_ecc_read_page() and expected it to only retrieve the data without
sending the READ0 command.

Create a gpmi_ecc_read_page_data() helper which only does the data
retrieval and ECC correction steps and implement gpmi_ecc_read_page()
as a wrapper that calls nand_read_page_op()+gpmi_ecc_read_page_data().

This way, gpmi_ecc_read_subpage() can call gpmi_ecc_read_page_data()
which restores the logic we had before commit 25f815f66a ("mtd: nand:
force drivers to explicitly send READ/PROG commands").

Fixes: 25f815f66a ("mtd: nand: force drivers to explicitly send READ/PROG commands")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Han Xu <han.xu@nxp.com>
2018-01-25 09:14:20 +01:00
Miquel Raynal c1a72e2dbb mtd: nand: Fix build issues due to an anonymous union
GCC-4.4.4 raises errors when assigning a parameter in an anonymous
union, leading to this kind of failure:

drivers/mtd/nand/marvell_nand.c:1936:
    warning: missing braces around initializer
    warning: (near initialization for '(anonymous)[1].<anonymous>')
    error: unknown field 'data' specified in initializer
    error: unknown field 'addr' specified in initializer

Work around the situation by naming these unions.

Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-20 10:39:02 +01:00
Miquel Raynal c495a9275e mtd: nand: marvell: Fix missing memory allocation modifier
The function marvell_nfc_init_dma() allocates a DMA buffer without the
GFP_KERNEL modifier, that triggers this warning:
"marvell_nfc_init_dma() error: no modifiers for allocation."

Fix this by using (GFP_KERNEL | GFP_DMA) instead of only GFP_DMA as the
probe happens in non-interrupt context.

Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-20 10:37:50 +01:00
Colin Ian King e06a181b5d mtd: nand: marvell: remove redundant variable 'oob_len'
Variable oob_len is assigned and never read, hence it is redundant and
can be removed.

Cleans up clang warnings:

drivers/mtd/nand/marvell_nand.c:1356:6: warning: Value stored to 'oob_len'
during its initialization is never read
drivers/mtd/nand/marvell_nand.c:1369:4: warning: Value stored to 'oob_len'
is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-19 09:40:10 +01:00
Colin Ian King a76497dc49 mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
Trivial fix to spelling mistakes in dev_err error message text.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-19 09:40:05 +01:00
Wei Yongjun e6b90db83f mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-19 09:40:03 +01:00
Bradley Bolen 7f29ae9f97 ubi: block: Fix locking for idr_alloc/idr_remove
This fixes a race with idr_alloc where gd->first_minor can be set to the
same value for two simultaneous calls to ubiblock_create.  Each instance
calls device_add_disk with the same first_minor.  device_add_disk calls
bdi_register_owner which generates several warnings.

WARNING: CPU: 1 PID: 179 at kernel-source/fs/sysfs/dir.c:31
sysfs_warn_dup+0x68/0x88
sysfs: cannot create duplicate filename '/devices/virtual/bdi/252:2'

WARNING: CPU: 1 PID: 179 at kernel-source/lib/kobject.c:240
kobject_add_internal+0x1ec/0x2f8
kobject_add_internal failed for 252:2 with -EEXIST, don't try to
register things with the same name in the same directory

WARNING: CPU: 1 PID: 179 at kernel-source/fs/sysfs/dir.c:31
sysfs_warn_dup+0x68/0x88
sysfs: cannot create duplicate filename '/dev/block/252:2'

However, device_add_disk does not error out when bdi_register_owner
returns an error.  Control continues until reaching blk_register_queue.
It then BUGs.

kernel BUG at kernel-source/fs/sysfs/group.c:113!
[<c01e26cc>] (internal_create_group) from [<c01e2950>]
(sysfs_create_group+0x20/0x24)
[<c01e2950>] (sysfs_create_group) from [<c00e3d38>]
(blk_trace_init_sysfs+0x18/0x20)
[<c00e3d38>] (blk_trace_init_sysfs) from [<c02bdfbc>]
(blk_register_queue+0xd8/0x154)
[<c02bdfbc>] (blk_register_queue) from [<c02cec84>]
(device_add_disk+0x194/0x44c)
[<c02cec84>] (device_add_disk) from [<c0436ec8>]
(ubiblock_create+0x284/0x2e0)
[<c0436ec8>] (ubiblock_create) from [<c0427bb8>]
(vol_cdev_ioctl+0x450/0x554)
[<c0427bb8>] (vol_cdev_ioctl) from [<c0189110>] (vfs_ioctl+0x30/0x44)
[<c0189110>] (vfs_ioctl) from [<c01892e0>] (do_vfs_ioctl+0xa0/0x790)
[<c01892e0>] (do_vfs_ioctl) from [<c0189a14>] (SyS_ioctl+0x44/0x68)
[<c0189a14>] (SyS_ioctl) from [<c0010640>] (ret_fast_syscall+0x0/0x34)

Locking idr_alloc/idr_remove removes the race and keeps gd->first_minor
unique.

Fixes: 2bf50d42f3 ("UBI: block: Dynamically allocate minor numbers")
Cc: stable@vger.kernel.org
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-18 16:48:31 +01:00
Wei Yongjun 7233982ade mtd: ubi: wl: Fix error return code in ubi_wl_init()
Fix to return error code -ENOMEM from the kmem_cache_alloc() error
handling case instead of 0, as done elsewhere in this function.

Fixes: f78e5623f4 ("ubi: fastmap: Erase outdated anchor PEBs during
attach")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-18 16:45:19 +01:00
Sascha Hauer 01f196945a ubi: Fix copy/paste error in function documentation
The function documentation of leb_write_trylock is copied from
leb_write_lock. Replace the function name with the correct one.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-18 00:18:51 +01:00
Sascha Hauer 889027bca2 ubi: Fastmap: Fix typo
Fix misspelling of 'available' in function name.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-18 00:18:50 +01:00
Sascha Hauer f78e5623f4 ubi: fastmap: Erase outdated anchor PEBs during attach
The fastmap update code might erase the current fastmap anchor PEB
in case it doesn't find any new free PEB. When a power cut happens
in this situation we must not have any outdated fastmap anchor PEB
on the device, because that would be used to attach during next
boot.
The easiest way to make that sure is to erase all outdated fastmap
anchor PEBs synchronously during attach.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-17 21:48:05 +01:00
Colin Ian King f50629df49 ubi: fastmap: Clean up the initialization of pointer p
The pointer p is being initialized with one value and a few lines
later being set to a newer replacement value. Clean up the code by
using the latter assignment to p as the initial value. Cleans up
clang warning:

drivers/mtd/ubi/fastmap.c:217:19: warning: Value stored to 'p'
during its initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-17 21:48:02 +01:00
Pan Bian af7bcee276 ubi: fastmap: Use kmem_cache_free to deallocate memory
Memory allocated by kmem_cache_alloc() should not be deallocated with
kfree(). Use kmem_cache_free() instead.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-17 21:48:02 +01:00
Clay McClure a51a0c8d21 ubi: Fix race condition between ubi volume creation and udev
Similar to commit 714fb87e8b ("ubi: Fix race condition between ubi
device creation and udev"), we should make the volume active before
registering it.

Signed-off-by: Clay McClure <clay@daemons.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-17 21:47:33 +01:00
Jeff Westfahl c0e860ba03 mtd: ubi: Use 'max_bad_blocks' to compute bad_peb_limit if available
If the user has not set max_beb_per1024 using either the cmdline or
Kconfig options for doing so, use the MTD function 'max_bad_blocks' to
compute the UBI bad_peb_limit.

Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-17 19:28:54 +01:00
Boris Brezillon 0aede42e98 mtd: Remove duplicate checks on mtd_oob_ops parameter
Some of the check done in custom ->_read/write_oob() implementation are
already done by the core (in mtd_check_oob_ops()).

Suggested-by: Peter Pan <peterpansjtu@gmail.com>
[Remove redundant checks done in mtdpart.c]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
2018-01-16 15:23:22 +01:00
Boris Brezillon 24ff129222 mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
Some MTD sublayers/drivers are implementing ->_read/write_oob() and
provide dummy wrappers for their ->_read/write() implementations.
Let the core handle this case instead of duplicating the logic.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
2018-01-16 15:23:21 +01:00
Boris Brezillon d020fc8e50 mtd: mtdpart: Make ECC stat handling consistent
part_read() and part_read_oob() were counting ECC failures and
bitflips differently. Adjust part_read_oob() to mimic what is done in
part_read(). This is needed to use ->_read_oob() as a fallback when
when ->_read() is not implemented.

Note that bitflips and ECC failure accounting on MTD partitions is
broken by design, because nothing prevents concurrent accesses to the
underlying master MTD device between the moment we save the stats in a
local variable and the moment master->_read[_oob]() returns. It's not
something that can easily be fixed, so leave it like that for now.

Suggested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
2018-01-16 15:23:21 +01:00
Arnd Bergmann 82cea533ae mtd: onenand: omap2: print resource using %pR format string
The omap2 onenand driver is now available for compile-testing, which
uncovers a warning in configurations that have a 64-bit resource_size_t:

drivers/mtd/onenand/omap2.c: In function 'omap2_onenand_probe':
drivers/mtd/onenand/omap2.c:536:54: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]
   dev_err(dev, "Cannot reserve memory region at 0x%08x, size: 0x%x\n",
drivers/mtd/onenand/omap2.c:536:66: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]

Changing the format string to the special %pR simplifies the code
and lets it do the right thing in that configuration, while avoiding
the warning.

Fixes: a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-16 09:25:12 +01:00
Guochun Mao 23bae78e8a mtd: mtk-nor: modify functions' name more generally
Since more and more Mediatek's SoC can use this driver to
control spi-nor flash, functions' name with "mt8173_" is
no longer properly. Replacing "mt8173_" with "mtk_" will
be more accurate to describe these functions' usable scope.

Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2018-01-14 16:14:06 +01:00
Christophe JAILLET 6837befde3 mtd: onenand: samsung: remove incorrect __iomem annotation
'page_buf' and 'oob_buf' are allocated with 'devm_kzalloc()' and should not
have __iomem decoration.

Remove these decorations and some useless casting.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-14 15:04:56 +01:00
Ladislav Michl a758f50f10 mtd: onenand: omap2: Configure driver from DT
Move away from platform data configuration and use pure DT approach.

Use generic probe function to deal with OneNAND node and remove now useless
gpmc_probe_onenand_child function. Import sync mode timing calculation
function from mach-omap2/gpmc-onenand.c

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 16:41:15 +01:00
Ladislav Michl bdaca9345d mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
INT pin (gpio_irq) is not really needed for DMA but only for notification
when a command that needs wait has completed. DMA memcpy can be still used
even without gpio_irq available, so enable it unconditionally.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 16:40:48 +01:00
Ladislav Michl f5229331f1 mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
Second commit in driver history (782b7a367d81: "[MTD] [OneNAND] OMAP3:
add delay for GPIO") added quirk for waiting until GPIO line settle.
As DMA was disabled for OMAP2 boards, chances are this problem was
not OMAP3 specific and as it is just one register read, previous
test for SoC type is approximately as expensive as read itself.
Make delay unconditional, which allows removing SoC specific code
alltogether.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:23 +01:00
Peter Ujfalusi 3ed6a4d1de mtd: onenand: omap2: Convert to use dmaengine for memcpy
Do not use the legacy and deprecated omap-dma interface for setting up the
memcpy.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:21 +01:00
Ladislav Michl fb25070afd mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
Since the very first commit (36cd4fb5d277: "[MTD] [OneNAND] Add
OMAP2 / OMAP3 OneNAND driver") DMA is disabled for OMAP2. Later
fixes thus went only into OMAP3 specific DMA functions which
turned out not to be so OMAP3 specific, so merge those two
implementations.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:19 +01:00
Peter Ujfalusi 3621311695 mtd: onenand: omap2: Simplify the DMA setup for various paths
We have 4 functions containing almost identical DMA setup code. Create one
function which can set up the DMA for both read and write and use this in
place for the setup code in the driver.
The new function will use wait_for_completion_io_timeout() and it will
figure out the best data_type to be used for the transfer instead of
hardwiring 32 or 16 bit data.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:17 +01:00
Ladislav Michl d120568883 mtd: onenand: omap2: Account waiting time as waiting on IO
Use wait_for_completion_io_timeout, which has an impact on how the
task is accounted in scheduling stats.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:15 +01:00
Ladislav Michl fafc0b3a9f mtd: onenand: omap2: Remove partitioning support from platform data
No platform data user setups partitioning information, so remove.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:13 +01:00
Ladislav Michl 11066d4295 mtd: onenand: omap2: Remove skip initial unlocking support
No platform data user sets skip_initial_unlocking, so remove test
for this field.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:10 +01:00
Ladislav Michl e6854e029b mtd: onenand: omap2: Remove regulator support
As no platform data user sets regulator_can_sleep, regulator code is
no-op and can be deleted.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:34:08 +01:00
Miquel Raynal 02f26ecf8c mtd: nand: add reworked Marvell NAND controller driver
Add marvell_nand driver which aims at replacing the existing pxa3xx_nand
driver.

The new driver intends to be easier to understand and follows the brand
new NAND framework rules by implementing hooks for every pattern the
controller might support and referencing them inside a parser object
that will be given to the core at each ->exec_op() call.

Raw accessors are implemented, useful to test/debug memory/filesystem
corruptions. Userspace binaries contained in the mtd-utils package may
now be used and their output trusted.

Most of the DT nodes using the old driver kept non-optimal timings from
the bootloader (even if there was some mechanisms to derive them if the
chip was ONFI compliant). The new default is to implement
->setup_data_interface() and follow the core's decision regarding the
chip.

Thanks to the improved timings, implementation of ONFI mode 5 support
(with EDO managed by adding a delay on data sampling), merging the
commands together and optimizing writes in the command registers, the
new driver may achieve faster throughputs in both directions.
Measurements show an improvement of about +23% read throughput and +24%
write throughput. These measurements have been done with an
Armada-385-DB-AP (4kiB NAND pages forced in 4-bit strength BCH ECC
correction) using the userspace tool 'flash_speed' from the MTD test
suite.

Besides these important topics, the new driver addresses several
unsolved known issues in the old driver which:
- did not work with ECC soft neither with ECC none ;
- relied on naked read/write (which is unchanged) while the NFCv1
  embedded in the pxa3xx platforms do not implement it, so several
  NAND commands did not actually ever work without any notice (like
  reading the ONFI PARAM_PAGE or SET/GET_FEATURES) ;
- wrote the OOB data correctly, but was not able to read it correctly
  past the first OOB data chunk ;
- did not retrieve ECC bytes ;
- used device tree bindings that did not allow more than one NAND chip,
  and did not allow to choose the correct chip select if not
  incrementing from 0. Plus, the Ready/Busy line used had to be 0.

Old device tree bindings are still supported but deprecated. A more
hierarchical view has to be used to keep the controller and the NAND
chip structures clearly separated both inside the device tree and also
in the driver code.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 15:17:06 +01:00
Miquel Raynal 87e89ce8d0 mtd: nand: Fix nand_do_read_oob() return value
Starting from commit 041e4575f0 ("mtd: nand: handle ECC errors in
OOB"), nand_do_read_oob() (from the NAND core) did return 0 or a
negative error, and the MTD layer expected it.

However, the trend for the NAND layer is now to return an error or a
positive number of bitflips. Deciding which status to return to the user
belongs to the MTD layer.

Commit e47f68587b ("mtd: check for max_bitflips in mtd_read_oob()")
brought this logic to the mtd_read_oob() function while the return value
coming from nand_do_read_oob() (called by the ->_read_oob() hook) was
left unchanged.

Fixes: e47f68587b ("mtd: check for max_bitflips in mtd_read_oob()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 10:30:48 +01:00
Miquel Raynal 12663b442e mtd: mtd_oobtest: Handle bitflips during reads
Reads from NAND devices usually trigger bitflips, this is an expected
behavior. While bitflips are under a given threshold, the MTD core
returns 0. However, when the number of corrected bitflips is above this
same threshold, -EUCLEAN is returned to inform the upper layer that this
block is slightly dying and soon the ECC engine will be overtaken so
actions should be taken to move the data out of it.

This particular condition should not be treated like an error and the
test should continue.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-12 10:24:08 +01:00
Christoph Hellwig ea8c64ace8 dma-mapping: move swiotlb arch helpers to a new header
phys_to_dma, dma_to_phys and dma_capable are helpers published by
architecture code for use of swiotlb and xen-swiotlb only.  Drivers are
not supposed to use these directly, but use the DMA API instead.

Move these to a new asm/dma-direct.h helper, included by a
linux/dma-direct.h wrapper that provides the default linear mapping
unless the architecture wants to override it.

In the MIPS case the existing dma-coherent.h is reused for now as
untangling it will take a bit of work.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
2018-01-10 16:40:54 +01:00
Ladislav Michl 09ec417b0e mtd: nand: samsung: Disable subpage writes on E-die NAND
Samsung E-die SLC NAND manufactured using 21nm process (K9F1G08U0E)
does not support partial page programming, so disable subpage writes
for it. Manufacturing process is stored in lowest two bits of 5th ID
byte.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-10 09:45:04 +01:00
Sascha Hauer 6cbefbdcec mtd: tests: nandbiterrs: Fix read_page return value
The number of corrected bitflips is not correctly reported by
the test until the bitflip threshold is reached.

read_page() shall return the number of corrected bitflips, but
mtd_read() returns 0 or a negative error, so we can't forward
its return value. In the absence of an error we always have
calculate the number of bitflips ourselves.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-09 10:56:29 +01:00
Kamal Dasu f953f0f896 mtd: nand: brcmnand: Disable prefetch by default
Brcm nand controller prefetch feature needs to be disabled
by default. Enabling affects performance on random reads as
well as dma reads.

Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Cc: <stable@vger.kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-09 10:00:04 +01:00
Mika Westerberg a6e4836d69 spi-nor: intel-spi: Remove unused preopcodes field
This field is not used in the driver anymore so remove it.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2018-01-07 21:22:32 +01:00
Julia Lawall 2167d6d7a9 mtd: fsl-quadspi: account for const type of of_device_id.data
This driver creates a number of const structures that it stores in the
data field of an of_device_id array.

The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.

Done using Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2018-01-07 19:06:12 +01:00
Vignesh R a27f2eaf2b mtd: spi-nor: cadence-quadspi: Add support for direct access mode
Cadence QSPI controller provides direct access mode through which flash
can be accessed in a memory-mapped IO mode. This enables read/write to
flash using memcpy*() functions. This mode provides higher throughput
for both read/write operations when compared to current indirect mode of
operation.

This patch therefore adds support to use QSPI in direct mode. If the
window reserved in SoC's memory map for MMIO access is less that of
flash size(like on most SoCFPGA variants), then the driver falls back
to indirect mode of operation.

On TI's 66AK2G SoC, with ARM running at 600MHz and QSPI at 96MHz
switching to direct mode improves read throughput from 3MB/s to 8MB/s.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2018-01-07 18:54:58 +01:00
Vignesh R e4b580bc04 mtd: spi-nor: cadence-quadspi: Refactor indirect read/write sequence.
Move configuring of indirect read/write start address to
cqspi_indirect_*_execute() function and rename cqspi_indirect_*_setup()
function. This will help to reuse cqspi_indirect_*_setup() function for
supporting direct access mode.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2018-01-07 18:53:13 +01:00
Boris Brezillon fee4380f36 mtd: nand: pxa3xx: Fix READOOB implementation
In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.

We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.

Fixes: 43bcfd2bb2 ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support")
Cc: stable@vger.kernel.org
Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
2018-01-06 23:06:58 +01:00
Fabio Estevam 069f05346d mtd: nand: qcom: Add a NULL check for devm_kasprintf()
devm_kasprintf() may fail, so we should better add a NULL check
and propagate an error on failure.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-06 21:55:42 +01:00
Boris Brezillon 33f45c44d6 mtd: Do not allow MTD devices with inconsistent erase properties
When mtd->erasesize is 0 or mtd->_erase is NULL, that means the device
does not support the erase operation, which in turn means it should
have the MTD_NO_ERASE flag set.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
2018-01-06 15:09:40 +01:00
Wei Yongjun 911c3a30ca mtd: sharpslpart: make local function sharpsl_nand_cleanup_ftl() static
Fixes the following sparse warnings:

drivers/mtd/parsers/sharpslpart.c:222:6: warning:
 symbol 'sharpsl_nand_cleanup_ftl' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-06 15:06:23 +01:00
Fabio Estevam 039b4377e5 mtd: nand: brcmnand: Add a NULL check for devm_kasprintf()
devm_kasprintf() may fail, so we should better add a NULL check
and propagate an error on failure.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-06 10:35:22 +01:00
Miquel Raynal d787b8b350 mtd: nand: Fix unfinished comment in nand_init_data_interface()
Give an unfinished comment a meaning.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2018-01-06 10:09:48 +01:00
Romain Porte 17407ec335 mtd: spi-nor: Add ISSI is25lp080d support
Add support for a new ISSI 1MB SPI NOR chip that was tested in our lab.
Datasheet is available at: http://www.issi.com/WW/pdf/25LP-WP080D.pdf

Testing was done only without the SPI_NOR_{DUAL,QUAD}_READ flags that
were added later, according to the datasheet.

Tested-by: Pascal Fabreges <pascal.fabreges@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Romain Porte <romain.porte@nokia.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-28 12:26:05 +01:00
Rafael Gago 0074a8f3b3 mtd: spi-nor: Add support for s25fl128l and s25fl256l
They are exactly the same as the s25fl064l but bigger.

Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-27 21:31:26 +01:00
Sean Nyekjaer 29d6b29f50 mtd: spi-nor: indent issi section
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-20 16:20:05 +01:00
Sean Nyekjaer ded8a0447f mtd: spi-nor: add support for is25lq040b
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-20 16:16:35 +01:00
Christophe JAILLET 24f648c2ba mtd: onenand: samsung: Remove a useless include
This include is not needed, so remove it.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-18 17:37:52 +01:00
Christophe JAILLET 0598344df0 mtd: onenand: samsung: Propagate the error returned by 'onenand_scan()'
Propagate the error code returned by 'onenand_scan()' instead of a
hard-coded -EFAULT.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-18 17:37:51 +01:00
Christophe JAILLET ad99be4772 mtd: onenand: samsung: return an error if 'mtd_device_parse_register()' fails
If 'mtd_device_parse_register()' fails, we still return 0 which mean
success.
Return the error code instead, as done in all the other error handling
paths.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-18 17:37:51 +01:00
Christophe JAILLET 8b5c51a45c mtd: onenand: samsung: use devm_ function to simplify code and fix some leaks
Convert all error handling code in 's3c_onenand_probe()' to
resource-managed alternatives in order to simplify code.

This fixes a resource leak if 'platform_get_resource()' fails at line 872.

The 'request_irq()' at line 971 was also un-balanced. It is now
resource-managed.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-18 17:37:39 +01:00
Colin Ian King b1d030f804 mtd: sharpslpart: fix overflow on block_adr calculation
Multiplying block_num and mtd->erasesize may potentially overflow
as they are both unsigned ints and so the multiplication is evaluated
in unsigned int arithmetic.  Cast block_adr to off_t to ensure
multiplication is off_t sized to avoid any potential overflow.

Detected by CoverityScan, CID#1461264 ("Unintentional integer overflow")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-18 13:30:04 +01:00
Miquel Raynal d82c368216 mtd: Fix mtd_check_oob_ops()
The mtd_check_oob_ops() helper verifies if the operation defined by the
user is correct.

Fix the check that verifies if the entire requested area exists. This
check is too restrictive and will fail anytime the last data byte of the
very last page is included in an operation.

Fixes: 5cdd929da5 ("mtd: Add sanity checks in mtd_write/read_oob()")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-12-18 09:16:35 +01:00
Antonio Borneo db601f3ad3 mtd: mchp23k256: propagate return value of spi_sync()
The call to spi_sync() can fail.
Check the return value and propagate it.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-17 09:10:14 +01:00
Colin Ian King bf6571057f mtd: mtdswap: make array 'name' static const, shrinks object size
Don't populate the read-only array 'name' on the stack but instead
make it static and constify it. Makes the object code smaller by 35
bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
  26304	   4444	    352	  31100	   797c	drivers/mtd/mtdswap.o

After:
   text	   data	    bss	    dec	    hex	filename
  26205	   4508	    352	  31065	   7959	drivers/mtd/mtdswap.o

(gcc version 7.2.0 x86_64)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-16 21:30:08 +01:00
Miquel Raynal 8878b126df mtd: nand: add ->exec_op() implementation
Introduce a new interface to instruct NAND controllers to send specific
NAND operations. The new interface takes the form of a single method
called ->exec_op(). This method is designed to replace ->cmd_ctrl(),
->cmdfunc() and ->read/write_byte/word/buf() hooks.

->exec_op() is passed a set of instructions describing the operation
to execute. Each instruction has a type (ADDR, CMD, DATA, WAITRDY)
and delay. The delay is here to help simple controllers wait enough
time between each instruction, advanced controllers with integrated
timings control can ignore these delays.

Controllers that natively support complex operations (operations
formed of several instructions) can use the NAND op parser
infrastructure. This infrastructure allows controller drivers to
describe the sequence of instructions they support (called
nand_op_pattern) and a hook for each of these supported sequences. The
core then tries to find the best match for a given NAND operation, and
calls the associated hook.

Various other helpers are also added to ease NAND controller drivers
writing.

This new interface should ease support of vendor specific operations
in that NAND manufacturer drivers now have a way to check if the
controller they are connected to supports a specific operation, and
complain or refuse to probe the NAND chip when that's not the case.

Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-16 14:40:26 +01:00
Christophe Leroy bc2fd1b110 mtd: nand: gpio: Fix ALE gpio configuration
Fixes a copy/paste error in commit f3d0d8d938 ("mtd: nand: gpio:
Convert to use GPIO descriptors") which breaks gpio-nand driver

Fixes: f3d0d8d938 ("mtd: nand: gpio: Convert to use GPIO descriptors")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-12-15 22:27:54 +01:00
Albert Hsieh e44b9a9c13 mtd: nand: brcmnand: Zero bitflip is not an error
A negative return value of brcmstb_nand_verify_erased_page() indicates a
real bitflip error of an erased page, and other return values (>= 0) show
the corrected bitflip number. Zero return value means no bitflip, but the
current driver code treats it as an error, and eventually leads to
falsely reported ECC error.

Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflip")
Signed-off-by: Albert Hsieh <wen.hsieh@broadcom.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-12-15 22:26:48 +01:00
Sascha Hauer fdf2e82105 mtd: nand: gpmi: Fix failure when a erased page has a bitflip at BBM
When erased subpages are read then the BCH decoder returns STATUS_ERASED
if they are all empty, or STATUS_UNCORRECTABLE if there are bitflips.
When there are bitflips, we have to set these bits again to show the
upper layers a completely erased page. When a bitflip happens in the
exact byte where the bad block marker is, then this byte is swapped
with another byte in block_mark_swapping(). The correction code then
detects a bitflip in another subpage and no longer corrects the bitflip
where it really happens.

Correct this behaviour by calling block_mark_swapping() after the
bitflips have been corrected.

In our case UBIFS failed with this bug because it expects erased
pages to be really empty:

UBIFS error (pid 187): ubifs_scan: corrupt empty space at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: corruption at LEB 36:118735
UBIFS error (pid 187): ubifs_scanned_corruption: first 8192 bytes from LEB 36:118735
UBIFS error (pid 187): ubifs_scan: LEB 36 scanning failed
UBIFS error (pid 187): do_commit: commit failed, error -117

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-12-15 22:26:15 +01:00
Miquel Raynal 707d81545d mtd: nand: samsung: add ECC requirements for K9F4G08U0D
Samsung NAND chip K9F4G08U0D minimum ECC strength requirement is 1 bit
per 512 bytes. As the chip is not ONFI nor JEDEC and because of the lack
of these values, boards using it fail to probe the NAND controller
driver. Fix this by setting up the default values.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:23 +01:00
Boris Brezillon aeb93af96d mtd: nand: Only allocate ecc->{calc, code}_buf when actually needed
The only users of the ecc->{calc,code}_buf buffers are NAND controller
drivers implementing ecc->calculate() and/or ecc->correct(). Since the
->oobsize can be non-negligle, especially on modern NAND devices, we'd
better allocate it only when it is actually required.

Make ecc->{calc,code}_buf allocation dependent on the presence of
ecc->calculate() or ecc->correct().

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-14 13:34:23 +01:00
Boris Brezillon 8c677541bb mtd: nand: denali: Avoid using ecc->code_buf as a temporary buffer
ECC bytes are contiguous in the ->oob_poi buffer, which means we don't
have to copy them into ->code_buf (here used as a temporary buffer)
before passing them to the nand_check_erased_ecc_chunk() function.

This change will allow us to allocate ecc->{code,calc}_buf only when
ecc->calculate() or ecc->correct() is specified.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-14 13:34:22 +01:00
RogerCC Lin 98dea8d719 mtd: nand: mtk: Support MT7622 NAND flash controller.
Add tables to support MT7622 NAND flash controller.

Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:22 +01:00
RogerCC Lin b45ee5501e mtd: nand: mtk: Support different MTK NAND flash controller IP
MT7622 uses an MTK's earlier NAND flash controller IP which support
different sector size, max spare size per sector and paraity bits...,
some register's offset and definition also been changed in the NAND
flash controller, this patch is the preparation to support MT7622
NAND flash controller.

MT7622 NFC and ECC engine are similar to MT2701's, except below
differences:
(1)MT7622 NFC's max sector size(ECC data size) is 512 bytes, and
   MT2701's is 1024, and MT7622's max sector number is 8.
(2)The parity bit of MT7622 is 13, MT2701 is 14.
(3)MT7622 ECC supports less ECC strength, max to 16 bit ecc strength.
(4)MT7622 supports less spare size per sector, max spare size per
   sector is 28 bytes.
(5)Some register's offset are different, include ECC_ENCIRQ_EN,
   ECC_ENCIRQ_STA, ECC_DECDONE, ECC_DECIRQ_EN and ECC_DECIRQ_STA.
(6)ENC_MODE of ECC_ENCCNFG register is moved from bit 5-6 to bit 4-5.

Signed-off-by: RogerCC Lin <rogercc.lin@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:21 +01:00
Ladislav Michl f170c6fb70 mtd: onenand: Remove obsolete url from Kconfig help
Samsung website no longer host information about OneNAND,
delete it.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:20 +01:00
Masahiro Yamada 958ef111cc mtd: nand: cafe: clean up DMA address setup
Use macros from <linux/kernel.h> to make the code readable.
The compiler warning will be kept suppressed.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:20 +01:00
Masahiro Yamada c0313b966a mtd: nand: squash struct nand_buffers into struct nand_chip
struct nand_buffers is malloc'ed in nand_scan_tail() just for
containing three pointers.  Squash this struct into nand_chip.

Move and rename as follows:

  chip->buffers->ecccalc   ->  chip->ecc.calc_buf
  chip->buffers->ecccode   ->  chip->ecc.code_buf
  chip->buffers->databuf   ->  chip->data_buf

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:19 +01:00
Masahiro Yamada 8b311ead8b mtd: nand: remove unused NAND_OWN_BUFFERS flag
The last/only user of NAND_OWN_BUFFERS (cafe_nand.c) has been reworked.
This flag is no longer needed.

Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:19 +01:00
Masahiro Yamada f880b07bf1 mtd: nand: cafe: remove use of NAND_OWN_BUFFERS
This driver is the last/only user of NAND_OWN_BUFFERS.  Boris suggested
to remove this flag.

Taking a closer look at this driver, it calls dma_alloc_coherent() for
the concatenated area for the DMA bounce buffer + struct nand_buffers,
but the latter does not need to be DMA-coherent; cafe_{write,read}_buf
simply do memcpy() between buffers when usedma==1.

Let's do dma_alloc_coherent() for the DMA bounce buffer in the front,
and leave the nand_buffers allocation to nand_scan_tail(), then rip off
NAND_OWN_BUFFERS.

The magic number, 2112, is still mysterious (hard-coded writesize +
oobsize ?), but this is not our main interest.  I am keeping it.

Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:18 +01:00
Miquel Raynal 17fa804418 mtd: nand: provide valid ->data_interface during NAND detection
Right now, the chip->data_interface field is populated in
nand_scan_tail(), so after the whole NAND detection has taken place.
This is fine because these timings are not yet used by the core so
early in the probe process, but the situation is about to change with
the introduction of ->exec_op().

Also, by convention, nand_scan_ident() is not supposed to allocate
resources, only nand_scan_tail() can, so this prevent us from
allocating and initializing the data_interface object in
nand_scan_ident().

In order to solve this problem, directly embed a data_interface object
in nand_chip so that we don't have to allocate it, and initialize it to
ONFI SDR mode 0 at the very beginning of nand_scan_ident().

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-14 13:34:18 +01:00
Boris Brezillon 25f815f66a mtd: nand: force drivers to explicitly send READ/PROG commands
The core currently send the READ0 and SEQIN+PAGEPROG commands in
nand_do_read/write_ops(). This is inconsistent with
->read/write_oob[_raw]() hooks behavior which are expected to send
these commands.

There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core
that a specific controller wants to send the READ/SEQIN+PAGEPROG
commands on its own, but it's an opt-in flag, and existing drivers are
unlikely to be updated to pass it.

Moreover, some controllers cannot dissociate the READ/PAGEPROG commands
from the associated data transfer and ECC engine activation, and
developers have to hack things in their ->cmdfunc() implementation to
handle such complex cases, or have to accept the perf penalty of sending
twice the same command.
To address this problem we are planning on adding a new interface which
is passed all information about a NAND operation (including the amount
of data to transfer) and replacing all calls to ->cmdfunc() to calls to
this new ->exec_op() hook. But, in order to do that, we need to have all
->cmdfunc() calls placed near their associated ->read/write_buf/byte()
calls.

Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS
the default case, and remove this flag.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: tested, fixed and rebased on nand/next]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-14 13:34:17 +01:00
Boris Brezillon 97d90da8a8 mtd: nand: provide several helpers to do common NAND operations
This is part of the process of removing direct calls to ->cmdfunc()
outside of the core in order to introduce a better interface to execute
NAND operations.

Here we provide several helpers and make use of them to remove all
direct calls to ->cmdfunc(). This way, we can easily modify those
helpers to make use of the new ->exec_op() interface when available.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[miquel.raynal@free-electrons.com: rebased and fixed some conflicts]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-14 13:34:12 +01:00
Hou Zhiqiang 59b356ffd0 mtd: m25p80: restore the status of SPI flash when exiting
Restore the status to be compatible with legacy devices.
Take Freescale eSPI boot for example, it copies (in 3 Byte
addressing mode) the RCW and bootloader images from SPI flash
without firing a reset signal previously, so the reboot command
will fail without resetting the addressing mode of SPI flash.
This patch implements .shutdown function to restore the status
in reboot process, and add the same operation to the .remove
function.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-13 00:36:00 +01:00
Hou Zhiqiang 8dee1d971a mtd: spi-nor: add an API to restore the status of SPI flash chip
Add this API to restore the status of SPI flash chip to the default
such as addressing mode, whenever detach the driver from device or
reboot the system.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-13 00:36:00 +01:00
Aaron Sierra 2666067fdb mtd: spi-nor: Check that BP bits are set properly
Previously, the lock and unlock functions returned success even if the
BP bits were not actually updated in the status register due to
hardware write protection. Introduce write_sr_and_check() to write and
read back the status register to ensure the desired BP bits are
actually set as requested.

Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-13 00:36:00 +01:00
Bean Huo (beanhuo) 20ccb993f2 mtd: spi-nor: check FSR error bits for Micron memories
For Micron spi nor device, when erase/program operation
fails, especially the failure results from intending to
modify protected space, spi-nor upper layers still get
the return which shows the operation succeeds. This is
because current spi_nor_fsr_ready() only uses FSR bit.7
(flag status register) to check device whether ready.
This patch fixes this issue by checking relevant error
bits in FSR.
The FSR is a powerful tool to investigate the status of
device, checking information regarding what the memory is
actually doing and detecting possible error conditions.

Signed-off-by: beanhuo <beanhuo@micron.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-13 00:36:00 +01:00
Angelo Dureghello 34354d4bf8 mtd: spi-nor: add support for ISSI is25lp128
Add support for ISSI is25lp128 spi nor flash.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-12-13 00:35:59 +01:00
Miquel Raynal eb94555e9e mtd: nand: use usual return values for the ->erase() hook
Avoid using specific defined values for checking returned status of the
->erase() hook. Instead, use usual negative error values on failure,
zero otherwise.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-12-01 09:45:30 +01:00
Masahiro Yamada 8a8c8ba1c8 mtd: nand: denali: rename misleading dma_buf to tmp_buf
The "dma_buf" is not used for a DMA bounce buffer, but for arranging
the transferred data for the syndrome page layout.  In fact, it is
used in the PIO mode as well, so "dma_buf" is a misleading name.
Rename it to "tmp_buf".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 22:32:50 +01:00
Masahiro Yamada c9e916a4b4 mtd: nand: remove unnecessary extern from driver headers
'extern' is not necessary for function declarations.

scripts/checkpatch.pl with --strict option reports the following:

  CHECK: extern prototypes should be avoided in .h files

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 22:32:49 +01:00
Jagdish Gediya bccb06c353 mtd: nand: ifc: update bufnum mask for ver >= 2.0.0
Bufnum mask is used to calculate page position in the internal SRAM.

As IFC version 2.0.0 has 16KB of internal SRAM as compared to older
versions which had 8KB. Hence bufnum mask needs to be updated.

Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 22:32:49 +01:00
Jesse Chan d822401d1c mtd: nand: denali_pci: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/mtd/nand/denali_pci.o
see include/linux/module.h for more information

This adds the license as "GPL v2", which matches the header of the file.

MODULE_DESCRIPTION and MODULE_AUTHOR are also added.

Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 22:32:48 +01:00
Sascha Hauer 34832dc44d mtd: nand: gpmi-nand: Remove wrong Kconfig help text
The GPMI nand Kconfig help texts mentions that the GPMI nand driver
might conflict with SD cards. The only conflict there might really
be is that both controllers use the same pins, but this is resolved
by the pincontroller setup in the device tree. In any way the GPMI
driver can safely be enabled, the text is just wrong. Remove it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 22:32:19 +01:00
Boris Brezillon 26f0740ed6 mtd: nand: hynix: Don't wait after applying new read-retry params
Setting read-retry parameters has no impact on the R/B pin, so waiting
for the chip to be ready is useless.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 11:02:52 +01:00
Miquel Raynal df467899da mtd: nand: fix interpretation of NAND_CMD_NONE in nand_command[_lp]()
Some drivers (like nand_hynix.c) call ->cmdfunc() with NAND_CMD_NONE
and a column address and expect the controller to only send address
cycles. Right now, the default ->cmdfunc() implementations provided by
the core do not filter out the command cycle in this case and forwards
the request to the controller driver through the ->cmd_ctrl() method.
The thing is, NAND controller drivers can get this wrong and send a
command cycle with a NAND_CMD_NONE opcode and since NAND_CMD_NONE is
-1, and the command field is usually casted to an u8, we end up sending
the 0xFF command which is actually a RESET operation.

Add conditions in nand_command[_lp]() functions to sending the initial
command cycle when command == NAND_CMD_NONE.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 11:02:50 +01:00
Gustavo A. R. Silva b13a9735ae mtd: nand: gpmi: replace _manual_ swap with swap macro
Make use of the swap macro and remove unnecessary variables swap.
This makes the code easier to read and maintain.

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 10:57:33 +01:00
Xiaolei Li f883199d17 mtd: nand: mtk: use nand_reset() to reset NAND devices in resume function
Previously, we only select chips and then send reset command to a NAND
device during resuming nand driver. There is a lack of deselecting chips.
It is advised to reset and initialize a NAND device using nand_reset().

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-11-30 10:57:27 +01:00
Linus Torvalds 1751e8a6cb Rename superblock flags (MS_xyz -> SB_xyz)
This is a pure automated search-and-replace of the internal kernel
superblock flags.

The s_flags are now called SB_*, with the names and the values for the
moment mirroring the MS_* flags that they're equivalent to.

Note how the MS_xyz flags are the ones passed to the mount system call,
while the SB_xyz flags are what we then use in sb->s_flags.

The script to do this was:

    # places to look in; re security/*: it generally should *not* be
    # touched (that stuff parses mount(2) arguments directly), but
    # there are two places where we really deal with superblock flags.
    FILES="drivers/mtd drivers/staging/lustre fs ipc mm \
            include/linux/fs.h include/uapi/linux/bfs_fs.h \
            security/apparmor/apparmorfs.c security/apparmor/include/lib.h"
    # the list of MS_... constants
    SYMS="RDONLY NOSUID NODEV NOEXEC SYNCHRONOUS REMOUNT MANDLOCK \
          DIRSYNC NOATIME NODIRATIME BIND MOVE REC VERBOSE SILENT \
          POSIXACL UNBINDABLE PRIVATE SLAVE SHARED RELATIME KERNMOUNT \
          I_VERSION STRICTATIME LAZYTIME SUBMOUNT NOREMOTELOCK NOSEC BORN \
          ACTIVE NOUSER"

    SED_PROG=
    for i in $SYMS; do SED_PROG="$SED_PROG -e s/MS_$i/SB_$i/g"; done

    # we want files that contain at least one of MS_...,
    # with fs/namespace.c and fs/pnode.c excluded.
    L=$(for i in $SYMS; do git grep -w -l MS_$i $FILES; done| sort|uniq|grep -v '^fs/namespace.c'|grep -v '^fs/pnode.c')

    for f in $L; do sed -i $f $SED_PROG; done

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-27 13:05:09 -08:00
Linus Torvalds 844056fd74 Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:

 - The final conversion of timer wheel timers to timer_setup().

   A few manual conversions and a large coccinelle assisted sweep and
   the removal of the old initialization mechanisms and the related
   code.

 - Remove the now unused VSYSCALL update code

 - Fix permissions of /proc/timer_list. I still need to get rid of that
   file completely

 - Rename a misnomed clocksource function and remove a stale declaration

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  m68k/macboing: Fix missed timer callback assignment
  treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
  timer: Remove redundant __setup_timer*() macros
  timer: Pass function down to initialization routines
  timer: Remove unused data arguments from macros
  timer: Switch callback prototype to take struct timer_list * argument
  timer: Pass timer_list pointer to callbacks unconditionally
  Coccinelle: Remove setup_timer.cocci
  timer: Remove setup_*timer() interface
  timer: Remove init_timer() interface
  treewide: setup_timer() -> timer_setup() (2 field)
  treewide: setup_timer() -> timer_setup()
  treewide: init_timer() -> setup_timer()
  treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
  s390: cmm: Convert timers to use timer_setup()
  lightnvm: Convert timers to use timer_setup()
  drivers/net: cris: Convert timers to use timer_setup()
  drm/vc4: Convert timers to use timer_setup()
  block/laptop_mode: Convert timers to use timer_setup()
  net/atm/mpc: Avoid open-coded assignment of timer callback function
  ...
2017-11-25 08:37:16 -10:00
Linus Torvalds 14b661ebb6 This pull request contains the following core changes:
General changes:
    * Unconfuse get_unmapped_area and point/unpoint driver methods
    * New partition parser: sharpslpart
    * Kill GENERIC_IO
    * Various fixes
 
 NAND changes:
    * Add a flag to mark NANDs that require 3 address cycles to encode a
      page address
    * Set a default ECC/free layout when NAND_ECC_NONE is requested
    * Fix a bug in panic_nand_write()
    * Another batch of cleanups for the denali driver
    * Fix PM support in the atmel driver
    * Remove support for platform data in the omap driver
    * Fix subpage write in the omap driver
    * Fix irq handling in the mtk driver
    * Change link order of mtk_ecc and mtk_nand drivers to speed up boot
      time
    * Change log level of ECC error messages in the mxc driver
    * Patch the pxa3xx driver to support Armada 8k platforms
    * Add BAM DMA support to the qcom driver
    * Convert gpio-nand to the GPIO desc API
    * Fix ECC handling in the mt29f driver
 
 SPI-NOR changes:
    * Introduce system power management support
    * New mechanism to select the proper .quad_enable() hook by JEDEC ID,
      when needed, instead of only by manufacturer ID
    * Add support to new memory parts from Gigadevice, Winbond, Macronix and
      Everspin
    * Maintainance for Cadence, Intel, Mediatek and STM32 drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABAgAGBQJaEzkZAAoJEGb5WYXrGLvBiUMP/25eEatNd5pGo9rtXqX463kp
 Q8zXGwtGp7Y2ThtC2TMbSSZZFdhGXIv3AUGpW+Y1yFMzGbiwWh8T28rdgDKDINhl
 jQteoWGQnZnnLhsMEbApJUqqtlxKFkY6COv/fUItmN8a4E5SyYF6ARKdnxH36Quu
 j/i3Kyd1FjDzJE2jsAE6TuomlNRuj/4S0OiZBTlgMhQvbo282Rush6RmF5zAvsdN
 B+S45Q752Pypg3U+1IYkqFSOtSYS3NM1ynZW7YXdWDwcKxDnKvasebSi+wCqPVc8
 n6hkcnXKIMOB6/bGhLg3FZlrzJcH7cbxy2C40NKFmMa7gw+/h1bmvjZk9hubLEc3
 +EJ8/1e8Z/KNTGu+Iyy2BNHTLI+KFKM5n/7/mpSPHMP/0uQjYs95GUmPlhVrenuv
 wprVsQKj7k92E+5Vm/h+Gys67sEG/rQK0v9UEConzl1s2T7i/hnA2lhPfIFmbMU/
 9U2s0CFobDqFUh+O6FSkLg9AT7+gT2HA1t6bbDTJMgnbFW72vlDUiArniia9hWOx
 dSc5pxMnaSiiqk+uCma4zLv2/3Tyi5dAEMQy+qAlK1EpmwPAsyu3SEMbyraovb9S
 PW0YQcMxVlQ/+EdDZCi83ypMlMQE/fDNcuKVMQD9enbko9yKGEgSZsTm9XwIvAv6
 g0P5jYMind1aNNSfg/QM
 =wVm7
 -----END PGP SIGNATURE-----

Merge tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd

Pull MTD updates from Richard Weinberger:
 "General changes:
   -  Unconfuse get_unmapped_area and point/unpoint driver methods
   -  New partition parser: sharpslpart
   -  Kill GENERIC_IO
   -  Various fixes

  NAND changes:
   -  Add a flag to mark NANDs that require 3 address cycles to encode a
      page address
   -  Set a default ECC/free layout when NAND_ECC_NONE is requested
   -  Fix a bug in panic_nand_write()
   -  Another batch of cleanups for the denali driver
   -  Fix PM support in the atmel driver
   -  Remove support for platform data in the omap driver
   -  Fix subpage write in the omap driver
   -  Fix irq handling in the mtk driver
   -  Change link order of mtk_ecc and mtk_nand drivers to speed up boot
      time
   -  Change log level of ECC error messages in the mxc driver
   -  Patch the pxa3xx driver to support Armada 8k platforms
   -  Add BAM DMA support to the qcom driver
   -  Convert gpio-nand to the GPIO desc API
   -  Fix ECC handling in the mt29f driver

  SPI-NOR changes:
   -  Introduce system power management support
   -  New mechanism to select the proper .quad_enable() hook by JEDEC
      ID, when needed, instead of only by manufacturer ID
   -  Add support to new memory parts from Gigadevice, Winbond, Macronix
      and Everspin
   -  Maintainance for Cadence, Intel, Mediatek and STM32 drivers"

*  tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
  mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
  mtd: sharpslpart: Add sharpslpart partition parser
  mtd: Add sanity checks in mtd_write/read_oob()
  mtd: remove the get_unmapped_area method
  mtd: implement mtd_get_unmapped_area() using the point method
  mtd: chips/map_rom.c: implement point and unpoint methods
  mtd: chips/map_ram.c: implement point and unpoint methods
  mtd: mtdram: properly handle the phys argument in the point method
  mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
  mtd: slram: use memremap() instead of ioremap()
  kconfig: kill off GENERIC_IO option
  mtd: Fix C++ comment in include/linux/mtd/mtd.h
  mtd: constify mtd_partition
  mtd: plat-ram: Replace manual resource management by devm
  mtd: nand: Fix writing mtdoops to nand flash.
  mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
  mtd: nand: mtk: fix infinite ECC decode IRQ issue
  mtd: spi-nor: Add support for mr25h128
  mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
  mtd: spi-nor: enable 4B opcodes for mx66l51235l
  ...
2017-11-22 20:46:06 -10:00
Kees Cook e99e88a9d2 treewide: setup_timer() -> timer_setup()
This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.

Casting from unsigned long:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, ptr);

and forced object casts:

    void my_callback(struct something *ptr)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);

become:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

Direct function assignments:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    ptr->my_timer.function = my_callback;

have a temporary cast added, along with converting the args:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;

And finally, callbacks without a data assignment:

    void my_callback(unsigned long data)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, 0);

have their argument renamed to verify they're unused during conversion:

    void my_callback(struct timer_list *unused)
    {
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

The conversion is done with the following Coccinelle script:

spatch --very-quiet --all-includes --include-headers \
	-I ./arch/x86/include -I ./arch/x86/include/generated \
	-I ./include -I ./arch/x86/include/uapi \
	-I ./arch/x86/include/generated/uapi -I ./include/uapi \
	-I ./include/generated/uapi --include ./include/linux/kconfig.h \
	--dir . \
	--cocci-file ~/src/data/timer_setup.cocci

@fix_address_of@
expression e;
@@

 setup_timer(
-&(e)
+&e
 , ...)

// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@

(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)

@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@

(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
 _E->_timer@_stl.function = _callback;
|
 _E->_timer@_stl.function = &_callback;
|
 _E->_timer@_stl.function = (_cast_func)_callback;
|
 _E->_timer@_stl.function = (_cast_func)&_callback;
|
 _E._timer@_stl.function = _callback;
|
 _E._timer@_stl.function = &_callback;
|
 _E._timer@_stl.function = (_cast_func)_callback;
|
 _E._timer@_stl.function = (_cast_func)&_callback;
)

// callback(unsigned long arg)
@change_callback_handle_cast
 depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
(
	... when != _origarg
	_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
)
 }

// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
 depends on change_timer_function_usage &&
                     !change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
+	_handletype *_origarg = from_timer(_origarg, t, _timer);
+
	... when != _origarg
-	(_handletype *)_origarg
+	_origarg
	... when != _origarg
 }

// Avoid already converted callbacks.
@match_callback_converted
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
	    !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@

 void _callback(struct timer_list *t)
 { ... }

// callback(struct something *handle)
@change_callback_handle_arg
 depends on change_timer_function_usage &&
	    !match_callback_converted &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@

 void _callback(
-_handletype *_handle
+struct timer_list *t
 )
 {
+	_handletype *_handle = from_timer(_handle, t, _timer);
	...
 }

// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
 depends on change_timer_function_usage &&
	    change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@

 void _callback(struct timer_list *t)
 {
-	_handletype *_handle = from_timer(_handle, t, _timer);
 }

// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg &&
	    !change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@

(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)

// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@

(
 _E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
)

// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@

 _callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
 )

// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@

(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)

@change_callback_unused_data
 depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *unused
 )
 {
	... when != _origarg
 }

Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 15:57:07 -08:00
Linus Torvalds 93f30c73ec Merge branch 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull compat and uaccess updates from Al Viro:

 - {get,put}_compat_sigset() series

 - assorted compat ioctl stuff

 - more set_fs() elimination

 - a few more timespec64 conversions

 - several removals of pointless access_ok() in places where it was
   followed only by non-__ variants of primitives

* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
  coredump: call do_unlinkat directly instead of sys_unlink
  fs: expose do_unlinkat for built-in callers
  ext4: take handling of EXT4_IOC_GROUP_ADD into a helper, get rid of set_fs()
  ipmi: get rid of pointless access_ok()
  pi433: sanitize ioctl
  cxlflash: get rid of pointless access_ok()
  mtdchar: get rid of pointless access_ok()
  r128: switch compat ioctls to drm_ioctl_kernel()
  selection: get rid of field-by-field copyin
  VT_RESIZEX: get rid of field-by-field copyin
  i2c compat ioctls: move to ->compat_ioctl()
  sched_rr_get_interval(): move compat to native, get rid of set_fs()
  mips: switch to {get,put}_compat_sigset()
  sparc: switch to {get,put}_compat_sigset()
  s390: switch to {get,put}_compat_sigset()
  ppc: switch to {get,put}_compat_sigset()
  parisc: switch to {get,put}_compat_sigset()
  get_compat_sigset()
  get rid of {get,put}_compat_itimerspec()
  io_getevents: Use timespec64 to represent timeouts
  ...
2017-11-17 11:54:55 -08:00
Linus Torvalds 5b0e2cb020 powerpc updates for 4.15
Non-highlights:
 
  - Five fixes for the >128T address space handling, both to fix bugs in our
    implementation and to bring the semantics exactly into line with x86.
 
 Highlights:
 
  - Support for a new OPAL call on bare metal machines which gives us a true NMI
    (ie. is not masked by MSR[EE]=0) for debugging etc.
 
  - Support for Power9 DD2 in the CXL driver.
 
  - Improvements to machine check handling so that uncorrectable errors can be
    reported into the generic memory_failure() machinery.
 
  - Some fixes and improvements for VPHN, which is used under PowerVM to notify
    the Linux partition of topology changes.
 
  - Plumbing to enable TM (transactional memory) without suspend on some Power9
    processors (PPC_FEATURE2_HTM_NO_SUSPEND).
 
  - Support for emulating vector loads form cache-inhibited memory, on some
    Power9 revisions.
 
  - Disable the fast-endian switch "syscall" by default (behind a CONFIG), we
    believe it has never had any users.
 
  - A major rework of the API drivers use when initiating and waiting for long
    running operations performed by OPAL firmware, and changes to the
    powernv_flash driver to use the new API.
 
  - Several fixes for the handling of FP/VMX/VSX while processes are using
    transactional memory.
 
  - Optimisations of TLB range flushes when using the radix MMU on Power9.
 
  - Improvements to the VAS facility used to access coprocessors on Power9, and
    related improvements to the way the NX crypto driver handles requests.
 
  - Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
 
 Thanks to:
   Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh
   Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao,
   Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R.
   Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren
   Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami
   Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
   Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de
   Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen
   Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain,
   Vaidyanathan Srinivasan, William A. Kennington III.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaDXGuAAoJEFHr6jzI4aWAEqwP/0TA35KFAK6wqfkCf67z4q+O
 I+5piI4eDV4jdCakfoIN1JfjhQRULNePSoCHTccan30mu/bm30p69xtOLL2/h5xH
 Mhz/eDBAOo0lrT20nyZfYMW3FnM66wnNf++qJ0O+8L052r4WOB02J0k1uM1ST01D
 5Lb5mUoxRLRzCgKRYAYWJifn+IFPUB9NMsvMTym94krAFlIjIzMEQXhDoln+jJMr
 QmY5f1BTA/fLfXobn0zwoc/C1oa2PUtxd+rxbwGrLoZ6G843mMqUi90SMr5ybhXp
 RzepnBTj4by3vOsnk/X1mANyaZfLsunp75FwnjHdPzKrAS/TuPp8D/iSxxE/PzEq
 cLwJFBnFXSgQMefDErXxhHSDz2dAg5r14rsTpDcq2Ko8TPV4rPsuSfmbd9Txekb0
 yWHsjoJUBBMl2QcWqIHl+AlV8j1RklF6solcTBcGnH1CZJMfa05VKXV7xGEvOHa0
 RJ+/xPyR9KjoB/SUp++9Vmx/M6SwQYFOJlr3Zpg9LNtR8WpoPYu1E6eO+u1Hhzny
 eJqaNstH+i+VdY9eqszkAsEBh8o9M/+b+7Wx7TetvU+v368CbXtgFYs9qy2oZjPF
 t9sY/BHaHZ8eZ7I00an77a0fVV5B1PVASUtIz5CqkwGpMvX6Z6W2K/XUUFI61kuu
 E06HS6Ht8UPJAzrAPUMl
 =Rq81
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "A bit of a small release, I suspect in part due to me travelling for
  KS. But my backlog of patches to review is smaller than usual, so I
  think in part folks just didn't send as much this cycle.

  Non-highlights:

   - Five fixes for the >128T address space handling, both to fix bugs
     in our implementation and to bring the semantics exactly into line
     with x86.

  Highlights:

   - Support for a new OPAL call on bare metal machines which gives us a
     true NMI (ie. is not masked by MSR[EE]=0) for debugging etc.

   - Support for Power9 DD2 in the CXL driver.

   - Improvements to machine check handling so that uncorrectable errors
     can be reported into the generic memory_failure() machinery.

   - Some fixes and improvements for VPHN, which is used under PowerVM
     to notify the Linux partition of topology changes.

   - Plumbing to enable TM (transactional memory) without suspend on
     some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND).

   - Support for emulating vector loads form cache-inhibited memory, on
     some Power9 revisions.

   - Disable the fast-endian switch "syscall" by default (behind a
     CONFIG), we believe it has never had any users.

   - A major rework of the API drivers use when initiating and waiting
     for long running operations performed by OPAL firmware, and changes
     to the powernv_flash driver to use the new API.

   - Several fixes for the handling of FP/VMX/VSX while processes are
     using transactional memory.

   - Optimisations of TLB range flushes when using the radix MMU on
     Power9.

   - Improvements to the VAS facility used to access coprocessors on
     Power9, and related improvements to the way the NX crypto driver
     handles requests.

   - Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.

  Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew
  Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin
  Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard,
  Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven,
  Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley,
  Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu,
  Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
  Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia
  Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee,
  Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel
  Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A.
  Kennington III"

* tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits)
  powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature
  powerpc/64s: Fix masking of SRR1 bits on instruction fault
  powerpc/64s: mm_context.addr_limit is only used on hash
  powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation
  powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary
  powerpc/64s/hash: Fix fork() with 512TB process address space
  powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation
  powerpc/64s/hash: Fix 512T hint detection to use >= 128T
  powerpc: Fix DABR match on hash based systems
  powerpc/signal: Properly handle return value from uprobe_deny_signal()
  powerpc/fadump: use kstrtoint to handle sysfs store
  powerpc/lib: Implement UACCESS_FLUSHCACHE API
  powerpc/lib: Implement PMEM API
  powerpc/powernv/npu: Don't explicitly flush nmmu tlb
  powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm()
  powerpc/powernv/idle: Round up latency and residency values
  powerpc/kprobes: refactor kprobe_lookup_name for safer string operations
  powerpc/kprobes: Blacklist emulate_update_regs() from kprobes
  powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace
  powerpc/kprobes: Disable preemption before invoking probe handler for optprobes
  ...
2017-11-16 12:47:46 -08:00
Linus Torvalds 1be2172e96 Modules updates for v4.15
Summary of modules changes for the 4.15 merge window:
 
 - Treewide module_param_call() cleanup, fix up set/get function
   prototype mismatches, from Kees Cook
 
 - Minor code cleanups
 
 Signed-off-by: Jessica Yu <jeyu@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABCgAGBQJaDCyzAAoJEMBFfjjOO8FyaYQP/AwHBy6XmwwVlWDP4BqIF6hL
 Vhy3ccVLYEORvePv68tWSRPUz5n6+1Ebqanmwtkw6i8l+KwxY2SfkZql09cARc33
 2iBE4bHF98iWQmnJbF6me80fedY9n5bZJNMQKEF9VozJWwTMOTQFTCfmyJRDBmk9
 iidQj6M3idbSUOYIJjvc40VGx5NyQWSr+FFfqsz1rU5iLGRGEvA3I2/CDT0oTuV6
 D4MmFxzE2Tv/vIMa2GzKJ1LGScuUfSjf93Lq9Kk0cG36qWao8l930CaXyVdE9WJv
 bkUzpf3QYv/rDX6QbAGA0cada13zd+dfBr8YhchclEAfJ+GDLjMEDu04NEmI6KUT
 5lP0Xw0xYNZQI7bkdxDMhsj5jaz/HJpXCjPCtZBnSEKiL4OPXVMe+pBHoCJ2/yFN
 6M716XpWYgUviUOdiE+chczB5p3z4FA6u2ykaM4Tlk0btZuHGxjcSWwvcIdlPmjm
 kY4AfDV6K0bfEBVguWPJicvrkx44atqT5nWbbPhDwTSavtsuRJLb3GCsHedx7K8h
 ZO47lCQFAWCtrycK1HYw+oupNC3hYWQ0SR42XRdGhL1bq26C+1sei1QhfqSgA9PQ
 7CwWH4UTOL9fhtrzSqZngYOh9sjQNFNefqQHcecNzcEjK2vjrgQZvRNWZKHSwaFs
 fbGX8juZWP4ypbK+irTB
 =c8vb
 -----END PGP SIGNATURE-----

Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux

Pull module updates from Jessica Yu:
 "Summary of modules changes for the 4.15 merge window:

   - treewide module_param_call() cleanup, fix up set/get function
     prototype mismatches, from Kees Cook

   - minor code cleanups"

* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  module: Do not paper over type mismatches in module_param_call()
  treewide: Fix function prototypes for module_param_call()
  module: Prepare to convert all module_param_call() prototypes
  kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
2017-11-15 13:46:33 -08:00
Boris Brezillon 1530578abd mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
Commit e8e3edb95c ("mtd: create per-device and module-scope debugfs
entries") tried to make MTD related debugfs stuff consistent across the
MTD framework by creating a root <debugfs>/mtd/ directory containing
one directory per MTD device.

The problem is that, by default, the MTD layer only registers the
master device if no partitions are defined for this master. This
behavior breaks all drivers that expect mtd->dbg.dfs_dir to be filled
correctly after calling mtd_device_register() in order to add their own
debugfs entries.

The only way we can force all MTD masters to be registered no matter if
they expose partitions or not is by enabling the
CONFIG_MTD_PARTITIONED_MASTER option.

In such situations, there's no other solution but to accept skipping
debugfs initialization when dbg.dfs_dir is invalid, and when this
happens, inform the user that he should consider enabling
CONFIG_MTD_PARTITIONED_MASTER.

Fixes: e8e3edb95c ("mtd: create per-device and module-scope debugfs entries")
Cc: <stable@vger.kernel.org>
Cc: Mario J. Rugiero <mrugiero@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 22:07:31 +01:00
Andrea Adami 8a4580e4d2 mtd: sharpslpart: Add sharpslpart partition parser
The Sharp SL Series (Zaurus) PXA handhelds have 16/64/128M of NAND flash
and share the same layout of the first 7M partition, managed by Sharp FTL.

GPL 2.4 sources: http://support.ezaurus.com/developer/source/source_dl.asp

The purpose of this self-contained patch is to add a common parser and
remove the hardcoded sizes in the board files (these devices are not yet
converted to devicetree).
Users will have benefits because the mtdparts= tag will not be necessary
anymore and they will be free to repartition the little sized flash.

The obsolete bootloader can not pass the partitioning info to modern
kernels anymore so it has to be read from flash at known logical addresses.
(see http://www.h5.dion.ne.jp/~rimemoon/zaurus/memo_006.htm )

In kernel, under arch/arm/mach-pxa we have already 8 machines:
MACH_POODLE, MACH_CORGI, MACH_SHEPERD, MACH_HUSKY, MACH_AKITA, MACH_SPITZ,
MACH_BORZOI, MACH_TOSA.
Lost after the 2.4 vendor kernel are MACH_BOXER and MACH_TERRIER.

Almost every model has different factory partitioning: add to this the
units can be repartitioned by users with userspace tools (nandlogical)
and installers for popular (back then) linux distributions.

The Parameter Area in the first (boot) partition extends from 0x00040000 to
0x0007bfff (176k) and contains two copies of the partition table:
...
0x00060000: Partition Info1     16k
0x00064000: Partition Info2     16k
0x00668000: Model               16k
...

The first 7M partition is managed by the Sharp FTL reserving 5% + 1 blocks
for wear-leveling: some blocks are remapped and one layer of translation
(logical to physical) is necessary.

There isn't much documentation about this FTL in the 2.4 sources, just the
MTD methods for reading and writing using logical addresses and the block
management (wear-leveling, use counter).
It seems this FTL was tailored with 16KiB eraesize in mind so to fit one
param block exactly, to have two copies of the partition table on two
blocks.
Later pxa27x devices have same size but 128KiB erasesize and less blocks
(56 vs. 448) but the same schema was adopted, even if the two tables are
now in the same eraseblock.

For the purpose of the MTD parser only the read part of the code was taken.

The NAND drivers that can use this parser are sharpsl.c and tmio_nand.c.

Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:19 +01:00
Boris Brezillon 5cdd929da5 mtd: Add sanity checks in mtd_write/read_oob()
Unlike what's done in mtd_read/write(), there are no checks to make sure
the parameters passed to mtd_read/write_oob() are consistent, which
forces implementers of ->_read/write_oob() to do it, which in turn leads
to code duplication and possibly errors in the logic.

Do general sanity checks, like ops fields consistency and range checking.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Peter Pan <peterpandong@micron.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:19 +01:00
Nicolas Pitre 9a5941080e mtd: remove the get_unmapped_area method
It is now unused.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:18 +01:00
Nicolas Pitre 9eaa903c06 mtd: implement mtd_get_unmapped_area() using the point method
The mtd->_point method is a superset of mtd->_get_unmapped_area.
Especially in the NOR flash case, the point method ensures the flash
memory is in array (data) mode and that it will stay that way which
is precisely what callers of mtd_get_unmapped_area() would expect.

Implement mtd_get_unmapped_area() in terms of mtd->_point now that all
drivers that provided a _get_unmapped_area method also have the _point
method implemented.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:18 +01:00
Nicolas Pitre 55100cfa33 mtd: chips/map_rom.c: implement point and unpoint methods
This will allow for the removal of the get_unmapped_area method later.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
[rw: fixed build]
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:18 +01:00
Nicolas Pitre 2caaf2d83a mtd: chips/map_ram.c: implement point and unpoint methods
This will allow for the removal of the get_unmapped_area method later.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:17 +01:00
Nicolas Pitre 877b58ebc0 mtd: mtdram: properly handle the phys argument in the point method
When the phys pointer is non null, the point method is expected to return
the physical address for the pointed area. In the case of the mtdram
driver we have to retrieve the physical address for the corresponding
vmalloc area. However, there is no guarantee that the vmalloc area is
made of physically contiguous pages. In that case we simply limit retlen
to the actually contiguous pages.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:17 +01:00
Arvind Yadav a5929b64fa mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
Trivial fix to spelling mistakes.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:16 +01:00
Roy Franz cb9e20633d mtd: slram: use memremap() instead of ioremap()
Convert slram to use memremap() to map the memory it uses to back an MTD
device, as this is the proper interface for mapping memory. This change
enables normal memory to be used to back an MTD device on arm64, as arm64
prevents ioremap() being used on normal memory.

Signed-off-by: Roy Franz <roy.franz@cavium.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: David Daney <david.daney@cavium.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:16 +01:00
Rob Herring 9de8da4774 kconfig: kill off GENERIC_IO option
The GENERIC_IO option is set for every architecture except tile and score
as those define NO_IOMEM. The option only controls visibility of
CONFIG_MTD which doesn't appear to be necessary for any reason, so let's
just remove GENERIC_IO.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: user-mode-linux-user@lists.sourceforge.net
Cc: linux-mtd@lists.infradead.org
Acked-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-13 21:39:15 +01:00
Arvind Yadav d4906688d4 mtd: constify mtd_partition
mtd_partition are not supposed to change at runtime.
Functions 'mtd_device_parse_register' working with const mtd_partition
provided by <linux/mtd/mtd.h>. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-06 23:26:01 +01:00
Anton Vasilyev 2e442aebed mtd: plat-ram: Replace manual resource management by devm
Driver contains unsuitable request_mem_region() and
release_resource() calls.

The patch switches manual resource management by devm interface for
readability and error-free simplification.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
2017-11-06 23:26:01 +01:00
Cyril Bur 6f469b67ff mtd: powernv_flash: Use opal_async_wait_response_interruptible()
The OPAL calls performed in this driver shouldn't be using
opal_async_wait_response() as this performs a wait_event() which, on
long running OPAL calls could result in hung task warnings. wait_event()
prevents timely signal delivery which is also undesirable.

This patch also attempts to quieten down the use of dev_err() when
errors haven't actually occurred and also to return better information up
the stack rather than always -EIO.

Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06 20:39:31 +11:00
Cyril Bur efe6941450 mtd: powernv_flash: Don't return -ERESTARTSYS on interrupted token acquisition
Because the MTD core might split up a read() or write() from userspace
into several calls to the driver, we may fail to get a token but already
have done some work, best to return -EINTR back to userspace and have
them decide what to do.

Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06 20:20:26 +11:00
Cyril Bur e32ec15a2d mtd: powernv_flash: Remove pointless goto in driver init
powernv_flash_probe() has pointless goto statements which jump to the
end of the function to simply return a variable. Rather than checking
for error and going to the label, just return the error as soon as it is
detected.

Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06 20:20:26 +11:00
Cyril Bur 25ee52e669 mtd: powernv_flash: Don't treat OPAL_SUCCESS as an error
While this driver expects to interact asynchronously, OPAL is well
within its rights to return OPAL_SUCCESS to indicate that the operation
completed without the need for a callback. We shouldn't treat
OPAL_SUCCESS as an error rather we should wrap up and return promptly to
the caller.

Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06 20:20:26 +11:00
Cyril Bur 44e2aa2b16 mtd: powernv_flash: Use WARN_ON_ONCE() rather than BUG_ON()
BUG_ON() should be reserved in situations where we can not longer
guarantee the integrity of the system. In the case where
powernv_flash_async_op() receives an impossible op, we can still
guarantee the integrity of the system.

Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-06 20:20:26 +11:00
Richard Weinberger 16271224bc Core changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
   page address
 * Set a default ECC/free layout when NAND_ECC_NONE is requested
 * Fix a bug in panic_nand_write()
 
 Driver changes:
 * Another batch of cleanups for the denali driver
 * Fix PM support in the atmel driver
 * Remove support for platform data in the omap driver
 * Fix subpage write in the omap driver
 * Fix irq handling in the mtk driver
 * Change link order of mtk_ecc and mtk_nand drivers to speed up boot
   time
 * Change log level of ECC error messages in the mxc driver
 * Patch the pxa3xx driver to support Armada 8k platforms
 * Add BAM DMA support to the qcom driver
 * Convert gpio-nand to the GPIO desc API
 * Fix ECC handling in the mt29f driver
 -----BEGIN PGP SIGNATURE-----
 
 iQJABAABCAAqBQJZ+iDfIxxib3Jpcy5icmV6aWxsb25AZnJlZS1lbGVjdHJvbnMu
 Y29tAAoJEGXtNgF+CLcAPxoP/iuRGzfzs7DTbS6rLtcbIFKbulj/kjB8BfPtYGC8
 1n7C2ZZkQOeargPyf1wtcvNgbVRjUv4/lZ22+HD7l/wDGDjOWeTs0v+it4yGVYzo
 iafyx+8m7J4kZWmZnguc6MQnFJ4g0yorUF3tmMYtd+OihgtlB/NWoxEAG40kPuhQ
 JpARsV/yWxV+l+30TBVtKCOmcS4tBh7Kjhlmr624BJv6sWilv63PnkG90a1qZUCw
 He2PLSNAXXaU7nWta+FKUSzIiRnsWhp2hqf9HIndx4zs1WHK86C15oBXvPuFs3q7
 FD5TB/sutTIhmkrqpZZJID/h1QDUkCYd9p2ZO6a0if/S1gZgiBKFFeJXcAlhj0Ze
 xqFvE/gni/w2mY8xlqX4/Ras5ndfMuNIIQgyCR/iDwQM4Sv6G5t59nMaCb7r0XYy
 Y1pZqVQ/jE8Kh5IkANEmQPVWv95OeQQwY0igtSb5Ih2J9cIzbX/8daE3CP1SOUaX
 REOmUJkb1Ad6gA9e3/nS0ZhLttmFtLEgxQqMQ16XWDtKkf+6uQcBPF/1JD6CuFjn
 0q6S5p1Mci/IZy2/ds9zIm42/dkG3LSLSG0cd2j60lTgTZsTloIsLcX120bDH/DM
 3LejsHgHuaA1Qd7ku9Bn/rfTZdQbSoqQtvkSw3t0touMG/5ErKuleTv9JDaoEb2e
 vRGr
 =iUhH
 -----END PGP SIGNATURE-----

Merge tag 'nand/for-4.15' of git://git.infradead.org/l2-mtd

From Boris:
"
Core changes:
* Add a flag to mark NANDs that require 3 address cycles to encode a
  page address
* Set a default ECC/free layout when NAND_ECC_NONE is requested
* Fix a bug in panic_nand_write()

Driver changes:
* Another batch of cleanups for the denali driver
* Fix PM support in the atmel driver
* Remove support for platform data in the omap driver
* Fix subpage write in the omap driver
* Fix irq handling in the mtk driver
* Change link order of mtk_ecc and mtk_nand drivers to speed up boot
  time
* Change log level of ECC error messages in the mxc driver
* Patch the pxa3xx driver to support Armada 8k platforms
* Add BAM DMA support to the qcom driver
* Convert gpio-nand to the GPIO desc API
* Fix ECC handling in the mt29f driver
"
2017-11-02 22:30:37 +01:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Brent Taylor 30863e38eb mtd: nand: Fix writing mtdoops to nand flash.
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.

When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.

Fixes: 2af7c65399 ("mtd: Add panic_write for NAND flashes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-10-31 16:25:43 +01:00
Kees Cook e4dca7b7aa treewide: Fix function prototypes for module_param_call()
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:

@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@

 module_param_call(_name, _set_func, _get_func, _arg, _mode);

@fix_set_prototype
 depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@

 int _set_func(
-_val_type _val
+const char * _val
 ,
-_param_type _param
+const struct kernel_param * _param
 ) { ... }

@fix_get_prototype
 depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@

 int _get_func(
-_val_type _val
+char * _val
 ,
-_param_type _param
+const struct kernel_param * _param
 ) { ... }

Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:

	drivers/platform/x86/thinkpad_acpi.c
	fs/lockd/svc.c

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
2017-10-31 15:30:37 +01:00
Kuppuswamy Sathyanarayanan ec0a9f62b3 mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
This patch adds Intel Lewisburg PCH SPI serial flash controller super
SKU PCI ID.

Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-30 11:51:18 +01:00
Xiaolei Li 1d2fcdcf33 mtd: nand: mtk: fix infinite ECC decode IRQ issue
For MT2701 NAND Controller, there may generate infinite ECC decode IRQ
during long time burn test on some platforms. Once this issue occurred,
the ECC decode IRQ status cannot be cleared in the IRQ handler function,
and threads cannot be scheduled.

ECC HW generates decode IRQ each sector, so there will have more than one
decode IRQ if read one page of large page NAND.

Currently, ECC IRQ handle flow is that we will check whether it is decode
IRQ at first by reading the register ECC_DECIRQ_STA. This is a read-clear
type register. If this IRQ is decode IRQ, then the ECC IRQ signal will be
cleared at the same time.
Secondly, we will check whether all sectors are decoded by reading the
register ECC_DECDONE. This is because the current IRQ may be not dealed
in time, and the next sectors have been decoded before reading the
register ECC_DECIRQ_STA. Then, the next sectors's decode IRQs will not
be generated.
Thirdly, if all sectors are decoded by comparing with ecc->sectors, then we
will complete ecc->done, set ecc->sectors as 0, and disable ECC IRQ by
programming the register ECC_IRQ_REG(op) as 0. Otherwise, wait for the
next ECC IRQ.

But, there is a timing issue between step one and two. When we read the
reigster ECC_DECIRQ_STA, all sectors are decoded except the last sector,
and the ECC IRQ signal is cleared. But the last sector is decoded before
reading ECC_DECDONE, so the ECC IRQ signal is enabled again by ECC HW, and
it means we will receive one extra ECC IRQ later. In step three, we will
find that all sectors were decoded, then disable ECC IRQ and return.
When deal with the extra ECC IRQ, the ECC IRQ status cannot be cleared
anymore. That is because the register ECC_DECIRQ_STA can only be cleared
when the register ECC_IRQ_REG(op) is enabled. But actually we have
disabled ECC IRQ in the previous ECC IRQ handle. So, there will
keep receiving ECC decode IRQ.

Now, we read the register ECC_DECIRQ_STA once again before completing the
ecc done event. This ensures that there will be no extra ECC decode IRQ.

Also, remove writel(0, ecc->regs + ECC_IRQ_REG(op)) from irq handler,
because ECC IRQ is disabled in mtk_ecc_disable(). And clear ECC_DECIRQ_STA
in mtk_ecc_disable() in case there is a timeout to wait decode IRQ.

Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Cc: <stable@vger.kernel.org>
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-10-30 09:35:04 +01:00
Philipp Puschmann 282e45dc64 mtd: spi-nor: Add support for mr25h128
Add Everspin mr25h128 16KB MRAM to the list of supported chips.

Signed-off-by: Philipp Puschmann <pp@emlix.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-29 20:57:19 +01:00
Xiaolei Li 1c782b9a85 mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
There will get mtk ecc handler during mtk nand probe now.
If mtk ecc module is not initialized, then mtk nand probe will return
-EPROBE_DEFER, and retry later.

Change the compile sequence of mtk_nand.o and mtk_ecc.o, initialize mtk
ecc module before mtk nand module. This makes mtk nand module initialized
as soon as possible.

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-10-29 20:40:40 +01:00
Roman Yeryomin d342b6a973 mtd: spi-nor: enable 4B opcodes for mx66l51235l
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-29 19:02:20 +01:00
Ludovic Barre 10cd4b7b74 mtd: spi-nor: stm32-quadspi: fix prefetching outside fsize
When memory-mapped mode is used, a prefetching mechanism fully
managed by the hardware allows to optimize the read from external
the QSPI memory. A 32-bytes FIFO is used for prefetching.
When the limit of flash size - fifo size is reached the prefetching
mechanism tries to read outside the fsize.
The stm32 quadspi hardware become busy and should be aborted.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reported-by: Bruno Herrera <bruherrera@gmail.com>
Tested-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-29 18:54:22 +01:00
Ludovic Barre e812963b91 mtd: spi-nor: stm32-quadspi: change license text
-Change the license text with long template.
-Change Copyright to STMicroelectronics.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-29 18:43:22 +01:00
Geert Uytterhoeven 05521bd3d1 mtd: spi-nor: stm32-quadspi: Fix uninitialized error return code
With gcc 4.1.2:

    drivers/mtd/spi-nor/stm32-quadspi.c: In function ‘stm32_qspi_tx_poll’:
    drivers/mtd/spi-nor/stm32-quadspi.c:230: warning: ‘ret’ may be used uninitialized in this function

Indeed, if stm32_qspi_cmd.len is zero, ret will be uninitialized.
This length is passed from outside the driver using the
spi_nor.{read,write}{,_reg}() callbacks.

Several functions in drivers/mtd/spi-nor/spi-nor.c (e.g. write_enable(),
write_disable(), and erase_chip()) call spi_nor.write_reg() with a zero
length.

Fix this by returning an explicit zero on success.

Fixes: 0d43d7ab27 ("mtd: spi-nor: add driver for STM32 quad spi flash controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-29 18:30:13 +01:00
Roger Quadros 739c64414f mtd: nand: omap2: Fix subpage write
Since v4.12, NAND subpage writes were causing a NULL pointer
dereference on OMAP platforms (omap2-nand) using OMAP_ECC_BCH4_CODE_HW,
OMAP_ECC_BCH8_CODE_HW and OMAP_ECC_BCH16_CODE_HW.

This is because for those ECC modes, omap_calculate_ecc_bch()
generates ECC bytes for the entire (multi-sector) page and this can
overflow the ECC buffer provided by nand_write_subpage_hwecc()
as it expects ecc.calculate() to return ECC bytes for just one sector.

However, the root cause of the problem is present since v3.9
but was not seen then as NAND buffers were being allocated
as one big chunk prior to commit 3deb9979c7 ("mtd: nand: allocate
aligned buffers if NAND_OWN_BUFFERS is unset").

Fix the issue by providing a OMAP optimized write_subpage()
implementation.

Fixes: 62116e5171 ("mtd: nand: omap2: Support for hardware BCH error correction.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2017-10-27 16:53:23 +02:00
Bin Meng b8cc001291 spi-nor: intel-spi: Remove EXPERT dependency
The idea to have the intel-spi driver dependent on EXPERT was exactly
because we did not want ordinary users playing with the device and
inadvertently overwrite their BIOSes (if it is not protected). This
seems to be superfluous hence remove it.

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-25 00:17:34 +02:00
Guochun Mao 2ea68b7541 mtd: mtk-nor: add suspend/resume support
Abstract functions of clock setting, to avoid duplicated code,
these functions been used in new feature.
Implement suspend/resume functions.

Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-24 23:58:55 +02:00
Neil Armstrong ace3cbdd23 mtd: spi-nor: Add support for Winbond w25q16dw
Add JEDEC entry for the Winbond w25q16fw/w25q16dw with similar
flags and format than the Winbond w25q32dw entry.

Tested on a Khadas VIM2 SBC board with an Amlogic S912 SoC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-23 09:49:51 +02:00
Vignesh R 4892b374c9 mtd: spi-nor: cadence-quadspi: Add runtime PM support
Add pm_runtime* calls to cadence-quadspi driver. This is required to
switch on QSPI power domain on TI 66AK2G SoC during probe.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-17 20:42:10 +02:00
Vignesh R 329864d35a mtd: spi-nor: cadence-quadspi: Fix error path in probe
Fix the reversed goto labels, so that we disable cqspi controller only
if its enabled previously. This is a minor cleanup.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-17 20:41:19 +02:00
Vignesh R e2580a4add mtd: spi-nor: cadence-quadspi: Add support to enable loop-back clock circuit
Cadence QSPI IP has a adapted loop-back circuit which can be enabled by
setting BYPASS field to 0 in READCAPTURE register. It enables use of
QSPI return clock to latch the data rather than the internal QSPI
reference clock. For high speed operations, adapted loop-back circuit
using QSPI return clock helps to increase data valid window.

Based on DT parameter cdns,rclk-en enable adapted loop-back circuit
for boards which do have QSPI return clock provided.
This patch also modifies cqspi_readdata_capture() function's bypass
parameter to bool to match how its used in the function.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-17 20:40:22 +02:00
Vignesh R 61dc8493ba mtd: spi-nor: cadence-quadspi: add a delay in write sequence
As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access
Controller programming sequence, a delay equal to couple of QSPI master
clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and
writing data to the flash. Introduce a quirk flag CQSPI_NEEDS_WR_DELAY
to handle this and set this flag for TI 66AK2G SoC.

[1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
2017-10-17 20:38:27 +02:00