Netdev reference helpers have a dev_ prefix for historic
reasons. Renaming the old helpers would be too much churn
but we can rename the tracking ones which are relatively
recent and should be the default for new code.
Rename:
dev_hold_track() -> netdev_hold()
dev_put_track() -> netdev_put()
dev_replace_track() -> netdev_ref_replace()
Link: https://lore.kernel.org/r/20220608043955.919359-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently tx push is a standard driver feature which controls use of a fast
path descriptor push. So this patch extends the ringparam APIs and data
structures to support set/get tx push by ethtool -G/g.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems I missed that most ethnl_parse_header_dev_get() callers
declare an on-stack struct ethnl_req_info, and that they simply call
dev_put(req_info.dev) when about to return.
Add ethnl_parse_header_dev_put() helper to properly untrack
reference taken by ethnl_parse_header_dev_get().
Fixes: e4b8954074 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to set rx buf len via ethtool -G parameter and get
rx buf len via ethtool -g parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, there are many drivers who support CQE mode configuration,
some configure it as a fixed when initialized, some provide an
interface to change it by ethtool private flags. In order to make it
more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and
'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these
parameters can be accessed by ethtool netlink coalesce uAPI.
Also add an new structure kernel_ethtool_coalesce, then the
new parameter can be added into this struct.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of subsequent extensions to both functions move the
implementations from netlink.h to netlink.c.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface for getting PHC (PTP Hardware Clock)
virtual clocks, which are based on PHC physical clock
providing hardware timestamp to network packets.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'ETHTOOL_A_MODULE_EEPROM_DATA' attribute is not part of the get
request.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most devices maintain RMON (RFC 2819) stats - particularly
the "histogram" of packets received by size. Unlike other
RFCs which duplicate IEEE stats, the short/oversized frame
counters in RMON don't seem to match IEEE stats 1-to-1 either,
so expose those, too. Do not expose basic packet, CRC errors
etc - those are already otherwise covered.
Because standard defines packet ranges only up to 1518, and
everything above that should theoretically be "oversized"
- devices often create their own ranges.
Going beyond what the RFC defines - expose the "histogram"
in the Tx direction (assume for now that the ranges will
be the same).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of devices maintains the standard-based MAC control
counters for control frames. Add a API for those.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the MAC statistics are included in
struct rtnl_link_stats64, but some fields
are aggregated. Besides it's good to expose
these clearly hardware stats separately.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface for reading standard stats, including
stats which don't have a corresponding control interface.
Start with IEEE 802.3 PHY stats. There seems to be only
one stat to expose there.
Define API to not require user space changes when new
stats or groups are added. Groups are based on bitset,
stats have a string set associated.
v1: wrap stats in a nest
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing 't' in attrtype.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define get_module_eeprom_by_page() ethtool callback and implement
netlink infrastructure.
get_module_eeprom_by_page() allows network drivers to dump a part of
module's EEPROM specified by page and bank numbers along with offset and
length. It is effectively a netlink replacement for get_module_info()
and get_module_eeprom() pair, which is needed due to emergence of
complex non-linear EEPROM layouts.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FEC API to netlink.
This is not a 1-to-1 conversion.
FEC settings already depend on link modes to tell user which
modes are supported. Take this further an use link modes for
manual configuration. Old struct ethtool_fecparam is still
used to talk to the drivers, so we need to translate back
and forth. We can revisit the internal API if number of FEC
encodings starts to grow.
Enforce only one active FEC bit (by using a bit position
rather than another mask).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ETHTOOL_A_STRSET_COUNTS_ONLY flag attribute was previously
not allowed to be used, but now due to the policy size reduction
we would access the tb[] array out of bounds since we tried to
check for the attribute despite it not being accepted.
Fix both issues by adding it correctly to the appropriate policy.
Fixes: ff419afa43 ("ethtool: trim policy tables")
Fixes: 71921690f9 ("ethtool: provide string sets with STRSET_GET request")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perform header flags validation through the policy.
Only pause command supports ETHTOOL_FLAG_STATS. Create a separate
policy to be able to express that in policy dumps to user space.
Note that even though the core will validate the header policy,
it cannot record multiple layers of attributes and we have to
re-parse header sub-attrs. When doing so we could skip attribute
validation, or use most permissive policy. Opt for the former.
We will no longer return the extack cookie for flags but since
we only added first new flag in this release it's not expected
that any user space had a chance to make use of it.
v2: - remove the re-validation in ethnl_parse_header_dev_get()
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get the most out of parsing by the core, and to allow dumping
full policies we need to specify which policy applies to nested
attrs. For headers it's ethnl_header_policy.
$ sed -i 's@\(ETHTOOL_A_.*HEADER\].*=\) { .type = NLA_NESTED },@\1\n\t\tNLA_POLICY_NESTED(ethnl_header_policy),@' net/ethtool/*
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ethtool uses strict attribute validation there's no need
to initialize all attributes in policy tables. 0 is NLA_UNSPEC
which is going to be rejected. Remove the NLA_REJECTs.
Similarly attributes above maxattrs are rejected, so there's
no need to always size the policy tables to ETHTOOL_A_..._MAX.
v2: - new patch
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to get commands wire up the policies of set commands
to get parsing by the core and policy dumps.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up policies for get commands in struct nla_policy of the ethtool
family. Make use of genetlink code attr validation and parsing, as well
as allow dumping policies to user space.
For every ETHTOOL_MSG_*_GET:
- add 'ethnl_' prefix to policy name
- add extern declaration in net/ethtool/netlink.h
- wire up the policy & attr in ethtool_genl_ops[].
- remove .request_policy and .max_attr from ethnl_request_ops.
Obviously core only records the first "layer" of parsed attrs
so we still need to parse the sub-attrs of the nested header
attribute.
v2:
- merge of patches 1 and 2 from v1
- remove stray empty lines in ops
- also remove .max_attr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make some helpers for building ethtool netlink messages available
outside the compilation unit, so they can be used for building
messages which are not simple get/set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new ethtool netlink calls to trigger the starting of a PHY cable
test.
Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when
ETHTOOL_NETLINK is builtin, which would result in kernel linking errors.
v2:
Remove unwanted white space change
Remove ethnl_cable_test_act_ops and use doit handler
Rename cable_test_set_policy cable_test_act_policy
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY
v3:
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation
Remove unused cable_test_get_policy
Add Reviewed-by tags
v4:
Remove unwanted blank line
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.
Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.
v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_SET netlink request to set EEE settings of a network device.
These are traditionally set with ETHTOOL_SEEE ioctl request.
The netlink interface allows setting the EEE status for all link modes
supported by kernel but only first 32 link modes can be set at the moment
as only those are supported by the ethtool_ops callback.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_GET request to get EEE settings of a network device. These
are traditionally available via ETHTOOL_GEEE ioctl request.
The netlink interface allows reporting EEE status for all link modes
supported by kernel but only first 32 link modes are provided at the moment
as only those are reported by the ethtool_ops callback and drivers.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_SET netlink request to set pause parameters of a network
device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl
request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_GET request to get pause parameters of a network device.
These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement COALESCE_SET netlink request to set coalescing parameters of
a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Like the ioctl implementation, the generic ethtool code checks if only
supported parameters are modified; if not, first offending attribute is
reported using extack.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement COALESCE_GET request to get coalescing parameters of a network
device. These are traditionally available via ETHTOOL_GCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Omit attributes with zero values unless they are declared as supported
(i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is
set).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement CHANNELS_SET netlink request to set channel counts of a network
device. These are traditionally set with ETHTOOL_SCHANNELS ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack. Checks preventing removing channels
used for RX indirection table or zerocopy AF_XDP socket are also
implemented.
Move ethtool_get_max_rxfh_channel() helper into common.c so that it can be
used by both ioctl and netlink code.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement CHANNELS_GET request to get channel counts of a network device.
These are traditionally available via ETHTOOL_GCHANNELS ioctl request.
Omit attributes for channel types which are not supported by driver or
device (zero reported for maximum).
v2: (all suggested by Jakub Kicinski)
- minor cleanup in channels_prepare_data()
- more descriptive channels_reply_size()
- omit attributes with zero max count
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement RINGS_SET netlink request to set ring sizes of a network device.
These are traditionally set with ETHTOOL_SRINGPARAM ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement RINGS_GET request to get ring sizes of a network device. These
are traditionally available via ETHTOOL_GRINGPARAM ioctl request.
Omit attributes for ring types which are not supported by driver or device
(zero reported for maximum).
v2: (all suggested by Jakub Kicinski)
- minor cleanup in rings_prepare_data()
- more descriptive rings_reply_size()
- omit attributes with zero max size
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PRIVFLAGS_SET netlink request to set private flags of a network
device. These are traditionally set with ETHTOOL_SPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PRIVFLAGS_GET request to get private flags for a network device.
These are traditionally available via ETHTOOL_GPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement FEATURES_SET netlink request to set network device features.
These are traditionally set using ETHTOOL_SFEATURES ioctl request.
Actual change is subject to netdev_change_features() sanity checks so that
it can differ from what was requested. Unlike with most other SET requests,
in addition to error code and optional extack, kernel provides an optional
reply message (ETHTOOL_MSG_FEATURES_SET_REPLY) in the same format but with
different semantics: information about difference between user request and
actual result and difference between old and new state of dev->features.
This reply message can be suppressed by setting ETHTOOL_FLAG_OMIT_REPLY
flag in request header.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement FEATURES_GET request to get network device features. These are
traditionally available via ETHTOOL_GFEATURES ioctl request.
v2:
- style cleanup suggested by Jakub Kicinski
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn pointed out that even if it's documented that
ethnl_parse_header() takes reference to network device if it fills it
into the target structure, its name doesn't make it apparent so that
corresponding dev_put() looks like mismatched.
Rename the function ethnl_parse_header_dev_get() to indicate that it
takes a reference.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement WOL_SET netlink request to set wake-on-lan settings. This is
equivalent to ETHTOOL_SWOL ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement WOL_GET request to get wake-on-lan settings for a device,
traditionally available via ETHTOOL_GWOL ioctl request.
As part of the implementation, provide symbolic names for wake-on-line
modes as ETH_SS_WOL_MODES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement DEBUG_SET netlink request to set debugging settings for a device.
At the moment, only message mask corresponding to message level as set by
ETHTOOL_SMSGLVL ioctl request can be set. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski
Jie Wang
Subbaraya Sundeep
Eric Dumazet
Hao Chen
Ido Schimmel
Yufeng Mo
Heiner Kallweit
Yangbo Lu
Zheng Yongjun
Vladyslav Tarasiuk
Danielle Ratson
Johannes Berg
Andrew Lunn
Michal Kubecek