libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The ata port is brought back to full power state during system resume.
So its runtime PM status will have to be updated to reflect
the actual post-system sleep status.
This also fixes below warning during system suspend/resume.
WARNING: at /work/linux/drivers/ata/libata-eh.c:4034
ata_scsi_port_error_handler+0x89/0x557()
4034 WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit b3a706014e (libata: Add a
drivers/ide style DMA disable) neglected to remove the line in
ata_do_set_mode() it has obviously made useless/duplicated. Do this
now, and make a line added back then wrapped properly...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change ata_host_request_pm to ata_port_request_pm which performs
port suspend/resume.
Add ata port type driver which implements port PM callbacks.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
XFER_SW_DMA_0 mode should be excluded from the extended cycle timing
computations.
Acked-by: Alan Cox <alan@linux.intel.com>
Noticed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link resume failure in itself isn't an error condition and may happen
regularly depending on hardware configuration. Reporting it as
KERN_ERR makes the condition unnecessarily prominent (e.g. reported
during boot). Use KERN_WARNING instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Shaw <dshaw@jabberwocky.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use a single mechanism to show driver version.
Reduces text a tiny bit too.
Remove uses of static int printed_version
Add and use ata_print_version(const struct device *, const char *ver)
and ata_print_version_once.
$ size drivers/ata/built-in.*
text data bss dec hex filename
544969 73893 116584 735446 b38d6 drivers/ata/built-in.allyesconfig.ata.o
543870 73893 116592 734355 b34ad drivers/ata/built-in.allyesconfig.print_once.o
141328 14689 4220 160237 271ed drivers/ata/built-in.defconfig.ata.o
141212 14689 4220 160121 27179 drivers/ata/built-in.defconfig.print_once.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Saves a bit of text as the call takes fewer args.
Coalesce a few formats.
Convert a few bare printks to pr_cont.
$ size drivers/ata/built-in.o*
text data bss dec hex filename
558429 73893 117864 750186 b726a drivers/ata/built-in.o.allyesconfig.new
559574 73893 117888 751355 b76fb drivers/ata/built-in.o.allyesconfig.old
149567 14689 4220 168476 2921c drivers/ata/built-in.o.defconfig.new
149851 14689 4220 168760 29338 drivers/ata/built-in.o.defconfig.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
regardless of firmware revision
It's unlikely NOSETXFER works for a revision of drive but doesn't for
another and pioneer doesn't seem to be fixing firmwares for the
affected drives. Apply NOSETXFER to the affected pioneer drives
regardless of firmware revision.
http://article.gmane.org/gmane.linux.ide/49734
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fl-00@gmx.de
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Give users the option of completely powering off unoccupied
SATA ports using the existing min_power link_power_management_policy
option. When the use selects this option on an empty port, we
will power the port off by setting DET to off. For occupied ports,
behavior is unchanged.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Commit 4a5610a04d fixed an issue with
the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
reported a similar issue with his DVR-216D that the NOSETXFER horkage
worked around for him as well.
This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.
The issue was reported at:
https://bugzilla.novell.com/show_bug.cgi?id=679143
Reported-by: Volodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.
Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths. This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVR-212D can't do SETXFER like its sibling DVRTD08. Add
ATA_HORKAGE_NOSETXFER for it. Reported in bko#27502.
https://bugzilla.kernel.org/show_bug.cgi?id=27502
Signed-off-by: Francesco Antonacci <fraanto@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
ata_qc_complete() contains special handling for certain commands. For
example, it schedules EH for device revalidation after certain
configurations are changed. These shouldn't be applied to EH
commands but they were.
In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.
Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().
stable: Please apply to -stable only after 2.6.38 is released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
In libata, the non-EH code paths should always take and release
ap->lock explicitly when accessing hardware or shared data structures.
However, once EH is active, it's assumed that the port is owned by EH
and EH methods don't explicitly take ap->lock unless race from irq
handler or other code paths are expected. However, libata EH didn't
guarantee exclusion among EHs for ports of the same host. IOW,
multiple EHs may execute in parallel on multiple ports of the same
controller.
In many cases, especially in SATA, the ports are completely
independent of each other and this doesn't cause problems; however,
there are cases where different ports share the same resource, which
lead to obscure timing related bugs such as the one fixed by commit
213373cf (ata_piix: fix locking around SIDPR access).
This patch implements exclusion among EHs of the same host. When EH
begins, it acquires per-host EH ownership by calling ata_eh_acquire().
When EH finishes, the ownership is released by calling
ata_eh_release(). EH ownership is also released whenever the EH
thread goes to sleep from ata_msleep() or explicitly and reacquired
after waking up.
This ensures that while EH is actively accessing the hardware, it has
exclusive access to it while allowing EHs to interleave and progress
in parallel as they hit waiting stages, which dominate the time spent
in EH. This achieves cross-port EH exclusion without pervasive and
fragile changes while still allowing parallel EH for the most part.
This was first reported by yuanding02@gmail.com more than three years
ago in the following bugzilla. :-)
https://bugzilla.kernel.org/show_bug.cgi?id=8223
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reported-by: yuanding02@gmail.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration. These will be used to implement EH exclusion.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current LPM implementation has the following issues.
* Operation order isn't well thought-out. e.g. HIPM should be
configured after IPM in SControl is properly configured. Not the
other way around.
* Suspend/resume paths call ata_lpm_enable/disable() which must only
be called from EH context directly. Also, ata_lpm_enable/disable()
were called whether LPM was in use or not.
* Implementation is per-port when it should be per-link. As a result,
it can't be used for controllers with slave links or PMP.
* LPM state isn't managed consistently. After a link reset for
whatever reason including suspend/resume the actual LPM state would
be reset leaving ap->lpm_policy inconsistent.
* Generic/driver-specific logic boundary isn't clear. Currently,
libahci has to mangle stuff which libata EH proper should be
handling. This makes the implementation unnecessarily complex and
fragile.
* Tied to ALPM. Doesn't consider DIPM only cases and doesn't check
whether the device allows HIPM.
* Error handling isn't implemented.
Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense. This patch reimplements
LPM support.
* The new implementation is per-link. The target policy is still
port-wide (ap->target_lpm_policy) but all the mechanisms and states
are per-link and integrate well with the rest of link abstraction
and can work with slave and PMP links.
* Core EH has proper control of LPM state. LPM state is reconfigured
when and only when reconfiguration is necessary. It makes sure that
LPM state is reset when probing for new device on the link.
Controller agnostic logic is now implemented in libata EH proper and
driver implementation only has to deal with controller specifics.
* Proper error handling. LPM config failure is attributed to the
device on the link and LPM is disabled for the link if it fails
repeatedly.
* ops->enable/disable_pm() are replaced with single ops->set_lpm()
which takes @policy and @hints. This simplifies driver specific
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management is about to be reimplemented. Prepare for it.
* Implement sata_link_scr_lpm().
* Drop static from ata_dev_set_feature() and make it available to
other libata files.
* Trivial whitespace adjustments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm. This patch cleans up lpm related symbols
and sysfs show/store functions as follows.
* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
ATA_LPM_{MIN|MAX|MED}_POWER.
* Pre/postfixes are unified to lpm.
* sysfs show/store functions for link_power_management_policy were
curiously named get/put and unnecessarily complex. Renamed to
show/store and simplified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way. libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.
This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions. This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.
* sata_fsl: It already builds done_mask. Conversion is straight
forward.
* sata_mv: mv_process_crpb_response() no longer checks for illegal
completions, it just returns whether the tag is completed or not.
mv_process_crpb_entries() builds done_mask from it and passes it to
ata_qc_complete_multiple() which will check for illegal completions.
* sata_nv adma: Similar to sata_mv. nv_adma_check_cpb() now just
returns the tag status and nv_adma_interrupt() builds done_mask from
it and passes it to ata_qc_complete_multiple().
* sata_nv swncq: It already builds done_mask. Drop unnecessary
illegal transition checks and call ata_qc_complete_multiple().
In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some mysterious reason, certain hardware reacts badly to usual EH
actions while the system is going for suspend. As the devices won't
be needed until the system is resumed, ask EH to skip usual autopsy
and recovery and proceed directly to suspend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Stephan Diestelhorst <stephan.diestelhorst@amd.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO. Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
'make htmldocs' has a fatal error when processing libata.xml, as seen
below. The string "Example patterns:" (or any string with "example.*:"
in it AFAIK) causes some part of the doc generation tool chain to try to
produce an <informalexample> block without a beginning <para>, but
there is an ending </para> generated, which throws things out of kilter.
I don't even know where (what program) this is happening in.
I searched in docproc and xmlto and in some XML stylesheets without
finding anything. If anyone can give me pointers about this, please do.
Until this is fixed, let's just spell "Example" as "Sample"
and match up the double quotation marks while there.
Documentation/DocBook/libata.xml:6575: parser error : Opening and ending tag mismatch: programlisting line 6573 and para
</para><para>
^
Documentation/DocBook/libata.xml:6580: parser error : Opening and ending tag mismatch: para line 6575 and programlisting
</programlisting></informalexample>
^
unable to parse Documentation/DocBook/libata.xml
make[2]: *** [Documentation/DocBook/libata.html] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (55 commits)
workqueue: mark init_workqueues() as early_initcall()
workqueue: explain for_each_*cwq_cpu() iterators
fscache: fix build on !CONFIG_SYSCTL
slow-work: kill it
gfs2: use workqueue instead of slow-work
drm: use workqueue instead of slow-work
cifs: use workqueue instead of slow-work
fscache: drop references to slow-work
fscache: convert operation to use workqueue instead of slow-work
fscache: convert object to use workqueue instead of slow-work
workqueue: fix how cpu number is stored in work->data
workqueue: fix mayday_mask handling on UP
workqueue: fix build problem on !CONFIG_SMP
workqueue: fix locking in retry path of maybe_create_worker()
async: use workqueue for worker pool
workqueue: remove WQ_SINGLE_CPU and use WQ_UNBOUND instead
workqueue: implement unbound workqueue
workqueue: prepare for WQ_UNBOUND implementation
libata: take advantage of cmwq and remove concurrency limitations
workqueue: fix worker management invocation without pending works
...
Fixed up conflicts in fs/cifs/* as per Tejun. Other trivial conflicts in
include/linux/workqueue.h, kernel/trace/Kconfig and kernel/workqueue.c
Take further advantage of the new glob_match() function to reduce
the blacklist size, this time making use of "character ranges" in
the patterns.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable use of hyphenated pattern ranges in glob_match(), similar to how
shell globbing works, and how developers might expect things to work.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take further advantage of the new glob_match() function to reduce
the blacklist size. There are even more savings possible, but how
far do we want to go with this?
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Take advantage of the new glob_match() function to reduce the blacklist
size somewhat. There are further savings possible, but these are
the most obvious biggies.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace rudimentry pattern matching with more capable shell-style globbing.
This will enable shrinking ata_device_blacklist[] table in subsequent patches,
and helps with future editions to the table, such as matching only the end
of a firmware revision string etc..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata has two concurrency related limitations.
a. ata_wq which is used for polling PIO has single thread per CPU. If
there are multiple devices doing polling PIO on the same CPU, they
can't be executed simultaneously.
b. ata_aux_wq which is used for SCSI probing has single thread. In
cases where SCSI probing is stalled for extended period of time
which is possible for ATAPI devices, this will stall all probing.
#a is solved by increasing maximum concurrency of ata_wq. Please note
that polling PIO might be used under allocation path and thus needs to
be served by a separate wq with a rescuer.
#b is solved by using the default wq instead and achieving exclusion
via per-port mutex.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Implement ata_scsi_unlock_native_capacity() which will be called
through SCSI layer when block layer notices that partitions on a
device extend beyond the end of the device. It requests EH to unlock
HPA, waits for completion and returns the current device capacity.
This allows libata to unlock HPA on demand instead of having to decide
whether to unlock upfront. Unlocking on demand is safer than
unlocking by upfront because some BIOSes write private data to the
area beyond HPA limit. This was suggested by Ben Hutchings.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After late HPA unlock, libata kept using the original capacity
ignoring the new larger native capacity. Enlarging device on the fly
doesn't cause any harm. Use the larger native capacity instead. This
will enable on-demand HPA unlocking.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add dump_id libata.force parameter. If specified, libata dumps full
IDENTIFY data during device configuration. This is to aid debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Baker <baker@usgs.gov>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are ATAPI devices which raise AN when hit by commands issued by
open(). This leads to infinite loop of AN -> MEDIA_CHANGE uevent ->
udev open() to check media -> AN.
Both ACS and SerialATA standards don't define in which case ATAPI
devices are supposed to raise or not raise AN. They both list media
insertion event as a possible use case for ATAPI ANs but there is no
clear description of what constitutes such events. As such, it seems
a bit too naive to export ANs directly to userland as MEDIA_CHANGE
events without further verification (which should behave similarly to
windows as it apparently is the only thing that some hardware vendors
are testing against).
This patch adds libata.atapi_an module parameter and disables ATAPI AN
by default for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: David Zeuthen <david@fubar.dk>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
port_task is tightly bound to the standard SFF PIO HSM implementation.
Using it for any other purpose would be error-prone and there's no
such user and if some drivers need such feature, it would be much
better off using its own. Move it inside CONFIG_ATA_SFF and rename it
to sff_pio_task.
The only function which is exposed to the core layer is
ata_sff_flush_pio_task() which is renamed from ata_port_flush_task()
and now also takes care of resetting hsm_task_state to HSM_ST_IDLE,
which is possible as it's now specific to PIO HSM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->[last_]ctl are specific to SFF controllers. Put them inside
CONFIG_ATA_SFF and move initialization into ata_sff_port_init().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan Williams
Vladimir LAVALLADE
Lin Ming
Sergei Shtylyov
Linus Torvalds
Bartlomiej Zolnierkiewicz
Tejun Heo
Joe Perches
Kristen Carlson Accardi
Jeff Mahoney
Maxime Bizon
Lucas De Marchi
Jeff Garzik
James Bottomley
Francesco Antonacci
Uwe Kleine-König
Tejun Heo
Gwendal Grignou
Randy Dunlap
Mark Lord