Add a separate config option for ide-8300 host driver instead of depending
on CONFIG_H8300.
This change is a preparation for the future changes and also allows ide-h8300
to be disabled if needed.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Only LWMON, IVMS8, IVML24 and TQM8xxL platforms have the needed
defines (IDE0_BASE_OFFSET and friends) in the platform header file.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add pci_enable_device() to aec62xx probe function
before doing any I/O.
Original probe function tries to read from device's
PCI region 4 before calling ide_setup_pci_device().
Since the device is not enabled at this point,
on machines that have no firmware PCI initialization
(e.g. ASUS WL-700gE router), corresponding PCI BAR
is 0 and the following inb() causes a kernel oops.
Signed-off-by: Aleksandar Radovanovic <biblbroks@sezampro.yu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is a problem in some hardware where the kernel will stall for
35 seconds waiting for disks that don't exist. This patch will skip
waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe"
as a kernel option and the disk is not marked as 'present' (like when
you set the geometry by hand).
If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for
that drive. Even if there would be a drive there and it is still busy
afterwards it should not matter since it isn't probed for later.
The code also honors the MAX_DRIVES variable instead of assuming that
there will be two harddrives on the bus.
Bart: minor cleanups
Signed-off-by: Jonas Stare <jonas.stare@purplescout.se>
CC: Andrew Morton <akpm@linux-foundation.org>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix handling of the PIO modes for the pre-EIDE drives that did not support
the PIO Flow Control Transfer Mode value (00001 nnn) of the Set Transfer Mode
feature by skipping the actual mode programming.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix ide-cris, cs5530, sc1200 and sis5513 host drivers to just return instead
of OOPS-ing for unsupported modes in ->set_dma_mode methods.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use drive->select.all for REQ_TYPE_ATA_TASK requests in execute_drive_cmd()
(the obsolete bits 7 and 5 of the Device register need to be set).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We can skip conservative PIO "downgrade" (PIO3 becomes PIO2 etc.) on PMAC.
Problem reported by Mikael.
Cc: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
LILO version 16 was released on 26-02-1995 (sic), so telling people to not use
older versions no longer has any value.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make sure to not clear the other IDE channel's interrupt when clearing an IDE
interrupt via the MRDMODE register.
Thanks to Bart for finding a coding mistake.
Bart:
This fixes regression from commit 66602c83dc
("cmd64x: use interrupt status from MRDMODE register (take 2)").
Extra thanks to Martin for reporting and bisecting the issue.
From: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Martin Rogge <marogge@onlinehome.de>
Tested-by: Milan Kocian <milon@wq.cz>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 33c1002ed9 incorrectly changed return
value from '0' to '-1', fix it (ns87415 was the only host driver affected
since it uses both IDE_HFLAG_TRUST_BIOS_FOR_DMA and IDE_HFLAG_NO_ATAPI_DMA).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drive_cmd_intr() is used by both REQ_TYPE_ATA_CMD and REQ_TYPE_ATA_TASK
but commands using PIO-in protocol are valid only for REQ_TYPE_ATA_CMD
(&args[4] in case of REQ_TYPE_ATA_TASK points to a value for IDE_LCYL_REG
register instead of the data buffer). This fix allows REQ_TYPE_ATA_TASK
commands to use non-zero values for IDE_SECTOR_REG (args[3]).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This config option is effective only for host drivers that use
IDE_HFLAG_OFF_BOARD host flag (aec62xx, generic, hpt34x, hpt366,
pdc202xx_new, pdc202xx_old and tc86c001).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_fix_driveid can now be unexported.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In piix.c (and in ata_piix.c) are already included some patches to skip the
cable check on some laptops and to enable UDMA > 33 modes, but I've noticed
than theese doesn't work on my Acer Aspire 5602WLMi (maybe exist more
versions of this laptop). With this simple patch I can set transfer mode
to UDMA100.
From: "sebdeg@ngi.it" <sebdeg@ngi.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
struct device doesn't have ->dma; it's in struct expansion_card where
that struct device is embedded into.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From the report by Nick Warne.
Tested-by: Nick Warne <nick@ukfsn.org>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* We shouldn't bother with dev->current_state, the PCI API functions we
call manage this for us (and do a far better job at it too).
* Remove pci_set_power_state(dev, PCI_D0) call in resume, as
pci_enable_device() does the same thing.
* Check pci_enable_device() return value. If it failed, fail
the entire resume and avoid programming timings into the [potentially
dead/asleep] chip.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that generic IDE PCI host driver is also affected by the same issue:
On Thursday 25 October 2007, Ralf Baechle wrote:
> CC drivers/ide/pci/generic.o
> drivers/ide/pci/generic.c:52: error: __setup_str_ide_generic_all_on causes a
> +section type conflict
[ Also reported by Martijn Uffing <mp3project@sarijopen.student.utwente.nl>. ]
This patch workarounds the problem in a bit hackish way but without
removing const from generic_chipsets[] (it adds const to __setup() so
__setup_str_ide_generic_all becomes const).
Now all __{dev}initdata data in generic IDE PCI host driver are read-only
so it builds again (driver's .init.data section gets marked as READONLY).
Cc: Martijn Uffing <mp3project@sarijopen.student.utwente.nl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that hpt366 host driver is also affected by the same issue:
> drivers/ide/pci/hpt366.c:1428: error: hpt366_chipsets causes a section type
> conflict
This patch workarounds the problem by making static struct hpt_info instances
const. Now all __devinitdata data in hpt366 host driver are read-only so it
builds again (driver's .init.data section gets marked as READONLY).
While at it:
* Bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently.
This patch workarounds the problem by removing __devinitdata tag from 'primary'
variable (which makes 'primary' to be moved from .init.data to .bss section).
Now all __devinitdata data in cy82c693 host driver are read-only so it builds
again (driver's .init.data section gets marked as READONLY).
While at it:
* Move 'primary' variable to its only user, init_iops_cy82c693().
* Bump driver version.
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
git-drivers/ide/ide-probe.c: In function 'hwif_init':
drivers/ide/ide-probe.c:1327: error: implicit declaration of function
'sg_init_table'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
It should be TASKFILE_NO_DATA, not TASKFILE_IN. Luckily ATM ->data_phase is
unused if ->command_type == IDE_DRIVE_TASK_NO_DATA but this may change in the
future.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These functions are atomic so locking is pointless (noticed by Sergei).
v2:
We can now just use local_irq_save/restore() in qd_testreg() (noticed by Jeff).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set hwif->dma_base only if allocation of extra ports succeeds.
While at it:
* Move setting of hwif->dma_{base,master} from ide_{mapped_mmio,iomio}_dma()
to ide_setup_dma().
* Rename 'dma_base' argument to 'base' in ide_setup_dma() (to make the code
obey 80-columns limit and increase its readability).
* Remove stale ide_setup_dma() comment.
v2:
* Change to allocate hwif->dmatable_cpu before reserving I/O ports missed
teardown code (spotted by Sergei). On the second thought this change is
actually unnecessary so revert it in v2.
* Make ide_release_dma_engine() void and remove needless comment.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove dead code from ide_driveid_update().
While at it:
* Remove useless comment.
* s/HWIF(drive)/drive->hwif/
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove dead code for handling IDE TCQ from ide_end_dequeued_request().
* Add 'dequeue' parameter to __ide_end_request().
* Use __ide_end_request() in ide_end_dequeued_request().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz
Aleksandar Radovanovic
Jonas Stare
Sergei Shtylyov
Gabriel Craciunescu
Adrian Bunk
Matti Linnanvuori
Tejun Heo
sebdeg@ngi.it
Linus Torvalds
Al Viro
Jeff Garzik
FUJITA Tomonori
Jens Axboe
Robert P. J. Day
Alan Cox