Currently DSA exposes the following sysfs:
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
which is a read-only device attribute, introduced in the kernel as
commit 98cdb48071 ("net: dsa: Expose tagging protocol to user-space"),
and used by libpcap since its commit 993db3800d7d ("Add support for DSA
link-layer types").
It would be nice if we could extend this device attribute by making it
writable:
$ echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
This is useful with DSA switches that can make use of more than one
tagging protocol. It may be useful in dsa_loop in the future too, to
perform offline testing of various taggers, or for changing between dsa
and edsa on Marvell switches, if that is desirable.
In terms of implementation, drivers can support this feature by
implementing .change_tag_protocol, which should always leave the switch
in a consistent state: either with the new protocol if things went well,
or with the old one if something failed. Teardown of the old protocol,
if necessary, must be handled by the driver.
Some things remain as before:
- The .get_tag_protocol is currently only called at probe time, to load
the initial tagging protocol driver. Nonetheless, new drivers should
report the tagging protocol in current use now.
- The driver should manage by itself the initial setup of tagging
protocol, no later than the .setup() method, as well as destroying
resources used by the last tagger in use, no earlier than the
.teardown() method.
For multi-switch DSA trees, error handling is a bit more complicated,
since e.g. the 5th out of 7 switches may fail to change the tag
protocol. When that happens, a revert to the original tag protocol is
attempted, but that may fail too, leaving the tree in an inconsistent
state despite each individual switch implementing .change_tag_protocol
transactionally. Since the intersection between drivers that implement
.change_tag_protocol and drivers that support D in DSA is currently the
empty set, the possibility for this error to happen is ignored for now.
Testing:
$ insmod mscc_felix.ko
[ 79.549784] mscc_felix 0000:00:00.5: Adding to iommu group 14
[ 79.565712] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
$ insmod tag_ocelot.ko
$ rmmod mscc_felix.ko
$ insmod mscc_felix.ko
[ 97.261724] libphy: VSC9959 internal MDIO bus: probed
[ 97.267363] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0
[ 97.274998] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1
[ 97.282561] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2
[ 97.289700] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3
[ 97.599163] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.862034] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 97.950731] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[ 97.964278] 8021q: adding VLAN 0 to HW filter on device swp0
[ 98.146161] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.238649] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[ 98.251845] 8021q: adding VLAN 0 to HW filter on device swp1
[ 98.433916] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[ 98.485542] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[ 98.503584] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 98.527948] device eno2 entered promiscuous mode
[ 98.544755] DSA: tree 0 setup
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=2.337 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.754 ms
^C
- 10.0.0.1 ping statistics -
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.754/1.545/2.337 ms
$ cat /sys/class/net/eno2/dsa/tagging
ocelot
$ cat ./test_ocelot_8021q.sh
#!/bin/bash
ip link set swp0 down
ip link set swp1 down
ip link set swp2 down
ip link set swp3 down
ip link set swp5 down
ip link set eno2 down
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
ip link set eno2 up
ip link set swp0 up
ip link set swp1 up
ip link set swp2 up
ip link set swp3 up
ip link set swp5 up
$ ./test_ocelot_8021q.sh
./test_ocelot_8021q.sh: line 9: echo: write error: Protocol not available
$ rmmod tag_ocelot.ko
rmmod: can't unload module 'tag_ocelot': Resource temporarily unavailable
$ insmod tag_ocelot_8021q.ko
$ ./test_ocelot_8021q.sh
$ cat /sys/class/net/eno2/dsa/tagging
ocelot-8021q
$ rmmod tag_ocelot.ko
$ rmmod tag_ocelot_8021q.ko
rmmod: can't unload module 'tag_ocelot_8021q': Resource temporarily unavailable
$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1): 56 data bytes
64 bytes from 10.0.0.1: seq=0 ttl=64 time=0.953 ms
64 bytes from 10.0.0.1: seq=1 ttl=64 time=0.787 ms
64 bytes from 10.0.0.1: seq=2 ttl=64 time=0.771 ms
$ rmmod mscc_felix.ko
[ 645.544426] mscc_felix 0000:00:00.5: Link is Down
[ 645.838608] DSA: tree 0 torn down
$ rmmod tag_ocelot_8021q.ko
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cascading DSA switches can be done multiple ways. There is the brute
force approach / tag stacking, where one upstream switch, located
between leaf switches and the host Ethernet controller, will just
happily transport the DSA header of those leaf switches as payload.
For this kind of setups, DSA works without any special kind of treatment
compared to a single switch - they just aren't aware of each other.
Then there's the approach where the upstream switch understands the tags
it transports from its leaves below, as it doesn't push a tag of its own,
but it routes based on the source port & switch id information present
in that tag (as opposed to DMAC & VID) and it strips the tag when
egressing a front-facing port. Currently only Marvell implements the
latter, and Marvell DSA trees contain only Marvell switches.
So it is safe to say that DSA trees already have a single tag protocol
shared by all switches, and in fact this is what makes the switches able
to understand each other. This fact is also implied by the fact that
currently, the tagging protocol is reported as part of a sysfs installed
on the DSA master and not per port, so it must be the same for all the
ports connected to that DSA master regardless of the switch that they
belong to.
It's time to make this official and enforce it (yes, this also means we
won't have any "switch understands tag to some extent but is not able to
speak it" hardware oddities that we'll support in the future).
This is needed due to the imminent introduction of the dsa_switch_ops::
change_tag_protocol driver API. When that is introduced, we'll have
to notify switches of the tagging protocol that they're configured to
use. Currently the tag_ops structure pointer is held only for CPU ports.
But there are switches which don't have CPU ports and nonetheless still
need to be configured. These would be Marvell leaf switches whose
upstream port is just a DSA link. How do we inform these of their
tagging protocol setup/deletion?
One answer to the above would be: iterate through the DSA switch tree's
ports once, list the CPU ports, get their tag_ops, then iterate again
now that we have it, and notify everybody of that tag_ops. But what to
do if conflicts appear between one cpu_dp->tag_ops and another? There's
no escaping the fact that conflict resolution needs to be done, so we
can be upfront about it.
Ease our work and just keep the master copy of the tag_ops inside the
struct dsa_switch_tree. Reference counting is now moved to be per-tree
too, instead of per-CPU port.
There are many places in the data path that access master->dsa_ptr->tag_ops
and we would introduce unnecessary performance penalty going through yet
another indirection, so keep those right where they are.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existence of dsa_broadcast has generated some confusion in the past:
https://www.mail-archive.com/netdev@vger.kernel.org/msg365042.html
So let's document the existing dsa_port_notify and dsa_broadcast
functions and explain when each of them should be used.
Also, in fact, the in-between function has always been there but was
lacking a name, and is the main reason for this patch: dsa_tree_notify.
Refactor dsa_broadcast to use it.
This patch also moves dsa_broadcast (a top-level function) to dsa2.c,
where it really belonged in the first place, but had no companion so it
stood with dsa_port_notify.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sja1105 implementation can be blind about this, but the felix driver
doesn't do exactly what it's being told, so it needs to know whether it
is a TX or an RX VLAN, so it can install the appropriate type of TCAM
rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use cache friendly helpers to better use cpu caches
while reading /proc/net/netstat
Tested on a platform with 256 threads (AMD Rome)
Before: 305 usec spent in netstat_seq_show()
After: 130 usec spent in netstat_seq_show()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210128162145.1703601-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit 41b14fb872 ("net: Do not clear the sock TX queue in
sk_set_socket()") removes sk_tx_queue_clear() from sk_set_socket() and adds
it instead in sk_alloc() and sk_clone_lock() to fix an issue introduced in
the commit e022f0b4a0 ("net: Introduce sk_tx_queue_mapping"). On the
other hand, the original commit had already put sk_tx_queue_clear() in
sk_prot_alloc(): the callee of sk_alloc() and sk_clone_lock(). Thus
sk_tx_queue_clear() is called twice in each path.
If we remove sk_tx_queue_clear() in sk_alloc() and sk_clone_lock(), it
currently works well because (i) sk_tx_queue_mapping is defined between
sk_dontcopy_begin and sk_dontcopy_end, and (ii) sock_copy() called after
sk_prot_alloc() in sk_clone_lock() does not overwrite sk_tx_queue_mapping.
However, if we move sk_tx_queue_mapping out of the no copy area, it
introduces a bug unintentionally.
Therefore, this patch adds a compile-time check to take care of the order
of sock_copy() and sk_tx_queue_clear() and removes sk_tx_queue_clear() from
sk_prot_alloc() so that it does the only allocation and its callers
initialize fields.
CC: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210128150217.6060-1-kuniyu@amazon.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch is to add csum offload support for gre header:
On the TX path in gre_build_header(), when CHECKSUM_PARTIAL's set
for inner proto, it will calculate the csum for outer proto, and
inner csum will be offloaded later. Otherwise, CHECKSUM_PARTIAL
and csum_start/offset will be set for outer proto, and the outer
csum will be offloaded later.
On the GSO path in gre_gso_segment(), when CHECKSUM_PARTIAL is
not set for inner proto and the hardware supports csum offload,
CHECKSUM_PARTIAL and csum_start/offset will be set for outer
proto, and outer csum will be offloaded later. Otherwise, it
will do csum for outer proto by calling gso_make_checksum().
Note that SCTP has to do the csum by itself for non GSO path in
sctp_packet_pack(), as gre_build_header() can't handle the csum
with CHECKSUM_PARTIAL set for SCTP CRC csum offload.
v1->v2:
- remove the SCTP part, as GRE dev doesn't support SCTP CRC CSUM
and it will always do checksum for SCTP in sctp_packet_pack()
when it's not a GSO packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NETIF_F_IP|IPV6_CSUM feature flag indicates UDP and TCP csum offload
while NETIF_F_HW_CSUM feature flag indicates ip generic csum offload
for HW, which includes not only for TCP/UDP csum, but also for other
protocols' csum like GRE's.
However, in skb_csum_hwoffload_help() it only checks features against
NETIF_F_CSUM_MASK(NETIF_F_HW|IP|IPV6_CSUM). So if it's a non TCP/UDP
packet and the features doesn't support NETIF_F_HW_CSUM, but supports
NETIF_F_IP|IPV6_CSUM only, it would still return 0 and leave the HW
to do csum.
This patch is to support ip generic csum processing by checking
NETIF_F_HW_CSUM for all protocols, and check (NETIF_F_IP_CSUM |
NETIF_F_IPV6_CSUM) only for TCP and UDP.
Note that we're using skb->csum_offset to check if it's a TCP/UDP
proctol, this might be fragile. However, as Alex said, for now we
only have a few L4 protocols that are requesting Tx csum offload,
we'd better fix this until a new protocol comes with a same csum
offset.
v1->v2:
- not extend skb->csum_not_inet, but use skb->csum_offset to tell
if it's an UDP/TCP csum packet.
v2->v3:
- add a note in the changelog, as Willem suggested.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1c ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210127173256.13954-2-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously a temporary tasklet structure was initialized on the stack
using DECLARE_TASKLET_OLD() and then copied over and modified. Nothing
else in the kernel seems to use this pattern, so let's just call
tasklet_init() like everyone else.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210127173256.13954-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Give offloading drivers the direction of the offloaded ct flow,
this will be used for matches on direction (ct_state +/-rpl).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's better make 'pkt_sk()' inline here, as non-inline function
shouldn't occur in headers. Besides, this function is simple
enough to be inline.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/20210127123302.29842-1-dong.menglong@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Validation of messages for get / del of a next hop is the same as will be
validation of messages for get of a resilient next hop group bucket. The
difference is that policy for resilient next hop group buckets is a
superset of that used for next-hop get.
It is therefore possible to reuse the code that validates the nhmsg fields,
extracts the next-hop ID, and validates that. To that end, extract from
nh_valid_get_del_req() a helper __nh_valid_get_del_req() that does just
that.
Make the nlh argument const so that the function can be called from the
dump context, which only has a const nlh. Propagate the constness to
nh_valid_get_del_req().
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to allow different handling for next-hop tree dumper and for
bucket dumper, parameterize the next-hop tree walker with a callback. Add
rtm_dump_nexthop_cb() with just the bits relevant for next-hop tree
dumping.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract from rtm_dump_nexthop() a helper to walk the next hop tree. A
separate function for this will be reusable from the bucket dumper.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dump operations need to keep state from one invocation to another. A
scratch area is dedicated for this purpose in the passed-in argument, cb,
namely via two aliased arrays, struct netlink_callback.args and .ctx.
Dumping of buckets will end up having to iterate over next hops as well,
and it would be nice to be able to reuse the iteration logic with the NH
dumper. The fact that the logic currently relies on fixed index to the
.args array, and the indices would have to be coordinated between the two
dumpers, makes this somewhat awkward.
To make the access patters clearer, introduce a helper struct with a NH
index, and instead of using the .args array directly, use it through this
structure.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Requests to dump nexthops have many attributes in common with those that
requests to dump buckets of resilient NH groups will have. However, they
have different policies. To allow reuse of this code, extract a
policy-agnostic wrapper out of nh_valid_dump_req(), and convert this
function into a thin wrapper around it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Requests to dump nexthops have many attributes in common with those that
requests to dump buckets of resilient NH groups will have. In order to make
reuse of this code simpler, convert the code to use a single structure with
filtering configuration instead of passing around the parameters one by
one.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After there are several next-hop group types, initialization and
finalization of notifier type needs to reflect the actual type. Transform
nh_notifier_grp_info_init() and _fini() to make extending them easier.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently there are only two types of in-kernel nexthop notification.
The two are distinguished by the 'is_grp' boolean field in 'struct
nh_notifier_info'.
As more notification types are introduced for more next-hop group types, a
boolean is not an easily extensible interface. Instead, convert it to an
enum.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the code that deals with nexthop groups relies on the fact that the
group is of exactly one well-known type. Currently there is only one type,
"mpath", but as more next-hop group types come, it becomes desirable to
have a central place where the setting is validated. Introduce such place
into nexthop_create_group(), such that the check is done before the code
that relies on that invariant is invoked.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The values that a next-hop group needs to keep track of depend on the group
type. Introduce a union to separate fields specific to the mpath groups
from fields specific to other group types.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The logic for selecting path depends on the next-hop group type. Adapt the
nexthop_select_path() to dispatch according to the group type.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nexthop_free_mpath really should be nexthop_free_group. Rename it.
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TX path no longer falls apart when some of its SG skbs are later
linearized by lower layers of the stack. So enable the use of SG skbs
in iucv_sock_sendmsg() again.
This effectively reverts
commit dc5367bcc5 ("net/af_iucv: don't use paged skbs for TX on HiperSockets").
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop maintaining the skb_send_q list for TRANS_HIPER sockets.
Not only is it extra overhead, but keeping around a list of skb clones
means that we later also have to match the ->sk_txnotify() calls
against these clones and free them accordingly.
The current matching logic (comparing the skbs' shinfo location) is
frustratingly fragile, and breaks if the skb's head is mangled in any
sort of way while passing from dev_queue_xmit() to the device's
HW queue.
Also adjust the interface for ->sk_txnotify(), to make clear that we
don't actually care about any skb internals.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TX code keeps track of all skbs that are in-flight but haven't
actually been sent out yet. For native IUCV sockets that's not a huge
deal, but with TRANS_HIPER sockets it would be much better if we
didn't need to maintain a list of skb clones.
Note that we actually only care about the _count_ of skbs in this stage
of the TX pipeline. So as prep work for removing the skb tracking on
TRANS_HIPER sockets, keep track of the skb count in a separate variable
and pair any list {enqueue, unlink} with a count {increment, decrement}.
Then replace all occurences where we currently look at the skb list's
fill level.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whoever called iucv_sk(sk)->sk_txnotify() must already know that they're
dealing with an af_iucv socket.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Parav Pandit Says:
=================
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Patch summary:
--------------
Patch 1 to 4 prepares devlink
patch 5 to 7 mlx5 adds SF device support
Patch 8 to 11 mlx5 adds SF devlink port support
Patch 12 and 14 adds documentation
Patch-1 prepares code to handle multiple port function attributes
Patch-2 introduces devlink pcisf port flavour similar to pcipf and pcivf
Patch-3 adds port add and delete driver callbacks
Patch-4 adds port function state get and set callbacks
Patch-5 mlx5 vhca event notifier support to distribute subfunction
state change notification
Patch-6 adds SF auxiliary device
Patch-7 adds SF auxiliary driver
Patch-8 prepares eswitch to handler SF vport
Patch-9 adds eswitch helpers to add/remove SF vport
Patch-10 implements devlink port add/del callbacks
Patch-11 implements devlink port function get/set callbacks
Patch-12 to 14 adds documentation
Patch-12 added mlx5 port function documentation
Patch-13 adds subfunction documentation
Patch-14 adds mlx5 subfunction documentation
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmALKDwACgkQSD+KveBX
+j7qjQf6A1moPhhIlXROCzaJUjlAj2U291LWBveU+I6na6fjYjAAWHYwfv0YKQpo
Qb0NRt+9abgEpGidc4hOwIJKhK+vlWrQuehRt83aAfAwaN3OEeGuNllniWo821Hj
sNiJfSC/DslOlQSxKLsAs3Fduy/sV3GN9Zv7hEwOFgEr5QvB2c6H1XiypVP2Ecsd
ZXC3SuEWxIoRtfXEkTkJne9LNoiDChlvT1FR/z75h8HUBdAOjzBTQzBbM+8M4Msw
8aKUPya3FMRAPWsOgPhkpU0xTtH2Mi7MC9TlwiWmrK4Q3uvesIav8pVf7r3GNAZA
sipIZ4gP0M5SiCaZa8rIBpTXBHxmvg==
=jEG4
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 subfunction support
Parav Pandit says:
This patchset introduces support for mlx5 subfunction (SF).
A subfunction is a lightweight function that has a parent PCI function on
which it is deployed. mlx5 subfunction has its own function capabilities
and its own resources. This means a subfunction has its own dedicated
queues(txq, rxq, cq, eq). These queues are neither shared nor stolen from
the parent PCI function.
When subfunction is RDMA capable, it has its own QP1, GID table and rdma
resources neither shared nor stolen from the parent PCI function.
A subfunction has dedicated window in PCI BAR space that is not shared
with the other subfunctions or parent PCI function. This ensures that all
class devices of the subfunction accesses only assigned PCI BAR space.
A Subfunction supports eswitch representation through which it supports tc
offloads. User must configure eswitch to send/receive packets from/to
subfunction port.
Subfunctions share PCI level resources such as PCI MSI-X IRQs with
their other subfunctions and/or with its parent PCI function.
Subfunction support is discussed in detail in RFC [1] and [2].
RFC [1] and extension [2] describes requirements, design and proposed
plumbing using devlink, auxiliary bus and sysfs for systemd/udev
support. Functionality of this patchset is best explained using real
examples further below.
overview:
--------
A subfunction can be created and deleted by a user using devlink port
add/delete interface.
A subfunction can be configured using devlink port function attribute
before its activated.
When a subfunction is activated, it results in an auxiliary device on
the host PCI device where it is deployed. A driver binds to the
auxiliary device that further creates supported class devices.
example subfunction usage sequence:
-----------------------------------
Change device to switchdev mode:
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Add a devlink port of subfunction flavour:
$ devlink port add pci/0000:06:00.0 flavour pcisf pfnum 0 sfnum 88
Configure mac address of the port function:
$ devlink port function set ens2f0npf0sf88 hw_addr 00:00:00:00:88:88
Now activate the function:
$ devlink port function set ens2f0npf0sf88 state active
Now use the auxiliary device and class devices:
$ devlink dev show
pci/0000:06:00.0
auxiliary/mlx5_core.sf.4
$ ip link show
127: ens2f0np0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 24:8a:07:b3:d1:12 brd ff:ff:ff:ff:ff:ff
altname enp6s0f0np0
129: p0sf88: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:00:00:00:88:88 brd ff:ff:ff:ff:ff:ff
$ rdma dev show
43: rdmap6s0f0: node_type ca fw 16.29.0550 node_guid 248a:0703:00b3:d112 sys_image_guid 248a:0703:00b3:d112
44: mlx5_0: node_type ca fw 16.29.0550 node_guid 0000:00ff:fe00:8888 sys_image_guid 248a:0703:00b3:d112
After use inactivate the function:
$ devlink port function set ens2f0npf0sf88 state inactive
Now delete the subfunction port:
$ devlink port del ens2f0npf0sf88
[1] https://lore.kernel.org/netdev/20200519092258.GF4655@nanopsycho/
[2] https://marc.info/?l=linux-netdev&m=158555928517777&w=2
=================
* tag 'mlx5-updates-2021-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Add devlink subfunction port documentation
devlink: Extend devlink port documentation for subfunctions
devlink: Add devlink port documentation
net/mlx5: SF, Port function state change support
net/mlx5: SF, Add port add delete functionality
net/mlx5: E-switch, Add eswitch helpers for SF vport
net/mlx5: E-switch, Prepare eswitch to handle SF vport
net/mlx5: SF, Add auxiliary device driver
net/mlx5: SF, Add auxiliary device support
net/mlx5: Introduce vhca state event notifier
devlink: Support get and set state of port function
devlink: Support add and delete devlink port
devlink: Introduce PCI SF port flavour and port attribute
devlink: Prepare code to fill multiple port function attributes
====================
Link: https://lore.kernel.org/r/20210122193658.282884-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wireless-drivers and netfilter trees. Nothing scary, Intel WiFi-related
fixes seemed most notable to the users.
Current release - regressions:
- dsa: microchip: ksz8795: fix KSZ8794 port map again to program
the CPU port correctly
Current release - new code bugs:
- iwlwifi: pcie: reschedule in long-running memory reads
Previous releases - regressions:
- iwlwifi: dbg: don't try to overwrite read-only FW data
- iwlwifi: provide gso_type to GSO packets
- octeontx2: make sure the buffer is 128 byte aligned
- tcp: make TCP_USER_TIMEOUT accurate for zero window probes
- xfrm: fix wraparound in xfrm_policy_addr_delta()
- xfrm: fix oops in xfrm_replay_advance_bmp due to a race between CPUs
in presence of packet reorder
- tcp: fix TLP timer not set when CA_STATE changes from DISORDER
to OPEN
- wext: fix NULL-ptr-dereference with cfg80211's lack of commit()
Previous releases - always broken:
- igc: fix link speed advertising
- stmmac: configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing
- team: protect features update by RCU to avoid deadlock
- xfrm: fix disable_xfrm sysctl when used on xfrm interfaces themselves
- fec: fix temporary RMII clock reset on link up
- can: dev: prevent potential information leak in can_fill_info()
Misc:
- mrp: fix bad packing of MRP test packet structures
- uapi: fix big endian definition of ipv6_rpl_sr_hdr
- add David Ahern to IPv4/IPv6 maintainers
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=dwFD
-----END PGP SIGNATURE-----
Merge tag 'net-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes including fixes from can, xfrm, wireless,
wireless-drivers and netfilter trees. Nothing scary, Intel
WiFi-related fixes seemed most notable to the users.
Current release - regressions:
- dsa: microchip: ksz8795: fix KSZ8794 port map again to program the
CPU port correctly
Current release - new code bugs:
- iwlwifi: pcie: reschedule in long-running memory reads
Previous releases - regressions:
- iwlwifi: dbg: don't try to overwrite read-only FW data
- iwlwifi: provide gso_type to GSO packets
- octeontx2: make sure the buffer is 128 byte aligned
- tcp: make TCP_USER_TIMEOUT accurate for zero window probes
- xfrm: fix wraparound in xfrm_policy_addr_delta()
- xfrm: fix oops in xfrm_replay_advance_bmp due to a race between
CPUs in presence of packet reorder
- tcp: fix TLP timer not set when CA_STATE changes from DISORDER to
OPEN
- wext: fix NULL-ptr-dereference with cfg80211's lack of commit()
Previous releases - always broken:
- igc: fix link speed advertising
- stmmac: configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA
addressing
- team: protect features update by RCU to avoid deadlock
- xfrm: fix disable_xfrm sysctl when used on xfrm interfaces
themselves
- fec: fix temporary RMII clock reset on link up
- can: dev: prevent potential information leak in can_fill_info()
Misc:
- mrp: fix bad packing of MRP test packet structures
- uapi: fix big endian definition of ipv6_rpl_sr_hdr
- add David Ahern to IPv4/IPv6 maintainers"
* tag 'net-5.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
rxrpc: Fix memory leak in rxrpc_lookup_local
mlxsw: spectrum_span: Do not overwrite policer configuration
selftests: forwarding: Specify interface when invoking mausezahn
stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing
net: usb: cdc_ether: added support for Thales Cinterion PLSx3 modem family.
ibmvnic: Ensure that CRQ entry read are correctly ordered
MAINTAINERS: add missing header for bonding
net: decnet: fix netdev refcount leaking on error path
net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP
can: dev: prevent potential information leak in can_fill_info()
net: fec: Fix temporary RMII clock reset on link up
net: lapb: Add locking to the lapb module
team: protect features update by RCU to avoid deadlock
MAINTAINERS: add David Ahern to IPv4/IPv6 maintainers
net/mlx5: CT: Fix incorrect removal of tuple_nat_node from nat rhashtable
net/mlx5e: Revert parameters on errors when changing MTU and LRO state without reset
net/mlx5e: Revert parameters on errors when changing trust state without reset
net/mlx5e: Correctly handle changing the number of queues when the interface is down
net/mlx5e: Fix CT rule + encap slow path offload and deletion
net/mlx5e: Disable hw-tc-offload when MLX5_CLS_ACT config is disabled
...
Add packet trap that can report packets that were dropped due to
destination MAC filtering.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* many minstrel improvements, including removal of the old
minstrel in favour of minstrel_ht
* speed improvements on FQ
* support for RX decapsulation (header conversion) offload
* RTNL reduction: limit RTNL usage in the wireless stack
mostly to where really needed (regulatory not yet) to
reduce contention on it
* various other small updates
-----BEGIN PGP SIGNATURE-----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=gIbl
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
More updates:
* many minstrel improvements, including removal of the old
minstrel in favour of minstrel_ht
* speed improvements on FQ
* support for RX decapsulation (header conversion) offload
* RTNL reduction: limit RTNL usage in the wireless stack
mostly to where really needed (regulatory not yet) to
reduce contention on it
* tag 'mac80211-next-for-net-next-2021-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (24 commits)
mac80211: minstrel_ht: fix regression in the max_prob_rate fix
virt_wifi: fix deadlock on RTNL
cfg80211: avoid holding the RTNL when calling the driver
cfg80211: change netdev registration/unregistration semantics
mac80211: minstrel_ht: fix rounding error in throughput calculation
mac80211: minstrel_ht: increase stats update interval
mac80211: minstrel_ht: fix max probability rate selection
mac80211: minstrel_ht: improve sample rate selection
mac80211: minstrel_ht: improve ampdu length estimation
mac80211: minstrel_ht: remove old ewma based rate average code
mac80211: remove legacy minstrel rate control
mac80211: minstrel_ht: add support for OFDM rates on non-HT clients
mac80211: minstrel_ht: clean up CCK code
mac80211: introduce aql_enable node in debugfs
cfg80211: Add phyrate conversion support for extended MCS in 60GHz band
cfg80211: add VHT rate entries for MCS-10 and MCS-11
mac80211: reduce peer HE MCS/NSS to own capabilities
mac80211: remove NSS number of 160MHz if not support 160MHz for HE
mac80211_hwsim: add 6GHz channels
mac80211: add LDPC encoding to ieee80211_parse_tx_radiotap
...
====================
Link: https://lore.kernel.org/r/20210127210915.135550-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmARLD8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqdlXB/48nQ5I+Z1wnhPvbtvyH4tk9XSbJaTt
4HH+i3R5RUAzHcOmfm2PQHe9/DxiogOQAFv9Lo0t7HN449bM3LMHrhTCcJIrIRf9
VxFSk4H97wjHR0Zj6TlEe++CTUPUalCpkCluERwqYP9WXRRklXL1mju+WNKnMMl0
9fl4CvQDWjB2wNXXoZ1SVuoFxyeqiKQHJy9n3Wez8sQTIlguOZvm8glDQlyb4v+q
rSxpCUrlpOVv6/11NqxQ7CfGdfTgLUi1a4greriwf1PjEXvDArXMjpDG3bo0kbgy
7Iv0U9GsvtzOPB+6XKxEFeYTKFaixyLugYBAadfvs0lVEIFP1mtlYvQs
=pHI/
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.12-20210127' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-01-27
The first two patches are by me and fix typos on the CAN gw protocol and the
flexcan driver.
The next patch is by Vincent Mailhol and targets the CAN driver infrastructure,
it exports the function that converts the CAN state into a human readable
string.
A patch by me, which target the CAN driver infrastructure, too, makes the
calculation in can_fd_len2dlc() more readable.
A patch by Tom Rix fixes a checkpatch warning in the mcba_usb driver.
The next seven patches target the mcp251xfd driver. Su Yanjun's patch replaces
several hardcoded assumptions when calling regmap, by using
regmap_get_val_bytes(). The remaining patches are by me. First an open coded
check is replaced by an existing helper function, then in the TX path the
padding for CAN-FD frames is cleaned up. The next two patches clean up the RTR
frame handling in the RX and TX path. Then support for len8_dlc is added. The
last patch adds BQL support.
* tag 'linux-can-next-for-5.12-20210127' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: mcp251xfd: add BQL support
can: mcp251xfd: add len8_dlc support
can: mcp251xfd: mcp251xfd_tx_obj_from_skb(): don't copy data for RTR CAN frames in TX-path
can: mcp251xfd: mcp251xfd_hw_rx_obj_to_skb(): don't copy data for RTR CAN frames in RX-path
can: mcp251xfd: mcp251xfd_tx_obj_from_skb(): clean up padding of CAN-FD frames
can: mcp251xfd: mcp251xfd_start_xmit(): use mcp251xfd_get_tx_free() to check TX is is full
can: mcp251xfd: replace sizeof(u32) with val_bytes in regmap
can: mcba_usb: remove h from printk format specifier
can: length: can_fd_len2dlc(): make legnth calculation readable again
can: dev: export can_get_state_str() function
can: flexcan: fix typos
can: gw: fix typo
====================
Link: https://lore.kernel.org/r/20210127092227.2775573-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove a duplicate code checking for header size in tipc_msg_create() as
it's already being done in tipc_msg_init().
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au>
Link: https://lore.kernel.org/r/20210127025123.6390-1-hoang.h.le@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Honor stateful expressions defined in the set from the dynset
extension. The set definition provides a stateful expression
that must be used by the dynset expression in case it is specified.
2) Missing timeout extension in the set element in the dynset
extension leads to inconsistent ruleset listing, not allowing
the user to restore timeout and expiration on ruleset reload.
3) Do not dump the stateful expression from the dynset extension
if it coming from the set definition.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nft_dynset: dump expressions when set definition contains no expressions
netfilter: nft_dynset: add timeout extension to template
netfilter: nft_dynset: honor stateful expressions in set definition
====================
Link: https://lore.kernel.org/r/20210127132512.5472-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two new port attributes which make EHT hosts limit configurable and
export the current number of tracked EHT hosts:
- IFLA_BRPORT_MCAST_EHT_HOSTS_LIMIT: configure/retrieve current limit
- IFLA_BRPORT_MCAST_EHT_HOSTS_CNT: current number of tracked hosts
Setting IFLA_BRPORT_MCAST_EHT_HOSTS_LIMIT to 0 is currently not allowed.
Note that we have to increase RTNL_SLAVE_MAX_TYPE to 38 minimum, I've
increased it to 40 to have space for two more future entries.
v2: move br_multicast_eht_set_hosts_limit() to br_multicast_eht.c,
no functional change
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a default limit of 512 for number of tracked EHT hosts per-port.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On building the route there is an assumption that the destination
could be local. In this case loopback_dev is used to get the address.
If the address is still cannot be retrieved dn_route_output_slow
returns EADDRNOTAVAIL with loopback_dev reference taken.
Cannot find hash for the fixes tag because this code was introduced
long time ago. I don't think that this bug has ever fired but the
patch is done just to have a consistent code base.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/1611619334-20955-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These Kconfig files are included from net/Kconfig, inside the
if NET ... endif.
Remove 'depends on NET', which we know it is already met.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210125232026.106855-1-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CONFIG_NET_L3_MASTER_DEV is a bool option. Change the ifeq conditional
to the standard obj-$(CONFIG_NET_L3_MASTER_DEV) form.
Use obj-y in net/l3mdev/Makefile because Kbuild visits this Makefile
only when CONFIG_NET_L3_MASTER_DEV=y.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210125231659.106201-4-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CONFIG_NET_SWITCHDEV is a bool option. Change the ifeq conditional to
the standard obj-$(CONFIG_NET_SWITCHDEV) form.
Use obj-y in net/switchdev/Makefile because Kbuild visits this Makefile
only when CONFIG_NET_SWITCHDEV=y.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210125231659.106201-3-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CONFIG_DCB is a bool option. Change the ifeq conditional to the
standard obj-$(CONFIG_DCB) form.
Use obj-y in net/dcb/Makefile because Kbuild visits this Makefile
only when CONFIG_DCB=y.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210125231659.106201-2-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_NET is disabled, nothing under the net/ directory is
compiled. Move the CONFIG_NET guard to the top Makefile so the net/
directory is entirely skipped.
When Kbuild visits net/Makefile, CONFIG_NET is obvioulsy 'y' because
CONFIG_NET is a bool option. Clean up net/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210125231659.106201-1-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CONFIG_NET is a bool option, and this file is compiled only when
CONFIG_NET=y.
Remove #ifdef CONFIG_NET, which we know it is always met.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210125231421.105936-1-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To avoid confusions like when working on the previous patch, better to
declare and assign this variable only where it is needed.
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean
Eric Dumazet
Kuniyuki Iwashima
Xin Long
Emil Renner Berthing
Paul Blakey
Menglong Dong
Petr Machata
Ido Schimmel
David Ahern
Julian Wiedmann
Alexander Egorenkov
Jakub Kicinski
Linus Torvalds
Takeshi Misawa
Aya Levin
Hoang Huu Le
Nikolay Aleksandrov
Vadim Fedorenko
Masahiro Yamada
Matthieu Baerts