Change subcmd parameter from int to u8 to match its use:
btmrvl_send_sync_cmd(priv, BT_CMD_MODULE_CFG_REQ, &subcmd, 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For SD8897, CMD52 write_to_clear may have missing interrupts
under certain corner case condition. Use CMD53 read-to-clear
to fix the problem.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If vendor specific HCI commands are received from application,
we should send corresponding events to stack.
These events should be consumed in driver, only if they are for
the internal HCI commands generated by driver.
This patch fixes the vendor command 0x3f stuck problem with
above mentioned change. For example,
hcitool cmd 3f 22 fe 06 22 21 20 43 50 00
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device tree property can define the cal-data in proper order.
There is no need to swap the bytes in driver.
Also remove the redundant cal-data memory copy after removing the
byte swapping.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some ARM versions of Chromebook need to download a new calibration
data from host driver to firmware. They do have EEPROM but still
need a piece of new calibration data in test mode.
The cal-data is platform dependent. It's simpler and more feasible
to use device tree based cal-data instead of configuration file
based cal-data.
This patch remove configuration file based cal-data downloading
and replace it using cal-data from device tree.
When CONFIG_OF is not selected, or the specific property is not
present in the device tree, the calibration downloading will not
happen.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hdev parameter of btmrvl_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btmrvl_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A text file containing calibration data in hex format can
be provided at following path:
/lib/firmware/mrvl/sd8797_caldata.conf
The data will be downloaded to firmware during initialization.
Reviewed-by: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace this proprietary structure with the standard one
(struct hci_command_hdr).
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Command preparation code is used multiple times. This patch
separate out this common code and create btmrvl_send_sync_cmd()
function.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is currently a race condition in the btmrvl_remove_card() which
is causing hangs on suspend for OLPC. When the race occurs,
kthread_stop() never returns.
The problem is that btmrvl_service_main_thread() calls kthread_should_stop()
and then does a fair number of things before restarting the loop and
sleeping.
If the thread gets stopped after kthread_should_stop() is checked, but
before the sleep happens, the thread will go to sleep and won't necessarily
be woken up.
Move the kthread_should_stop() check into a race-free place.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch shortens locals scope and adds missing braces. This is a diff
between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do
not send vendor events to bluetooth stack".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Currently debugfs commands "hscfgcmd" and "gpiogap" are provided
for host sleep configuration. But if user doesn't configure host
sleep parameters using these commands, host sleep activation is
failed during suspend (support for suspend and resume handlers is
added in next patch).
Default host sleep configuration is done during driver initialisation
in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The linux device model provides dev_set/get_drvdata so we can use this
to save private driver data.
This also removes several unnecessary casts.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After unregistering an hci_dev object a bluetooth driver does not have
any callbacks in the hci_dev structure left over. Therefore, there is no
need to keep a reference to the module.
Previously, we needed this to protect the hci-destruct callback.
However, this callback is no longer available so we do not need this
owner field, anymore. Drivers now call hci_unregister_dev() and they
are done with the object.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The callback is optional and we provide an empty callback so remove it
entirely.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some drivers set PF_NOFREEZE in their kthread functions which is
completely unnecessary and racy - some part of freezer code doesn't
consider cases where PF_NOFREEZE is set asynchronous to freezer
operations.
In general, there's no reason to allow setting PF_NOFREEZE explicitly.
Remove them and change the documentation to note that setting
PF_NOFREEZE directly isn't allowed.
-v2: Dropped change to twl4030-irq.c as it no longer uses PF_NOFREEZE.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "Gustavo F. Padovan" <padovan@profusion.mobi>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: wwang <wei_wang@realsil.com.cn>
HCI transport drivers may not know what type of radio an AMP device has
so only say whether they're BR/EDR or AMP devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When driver is sending a command or data and the firmware is also
sending a sleep event, sometimes it is observed that driver will
continue to send the command/data to firmware right after processing
sleep event. Once sleep event is processed driver is not supposed to
send anything because firmware is in sleep state after that. Previously
interrupt processing was done in SDIO interrupt callback handler.
Now it is done in btmrvl driver main thread to solve the
cross-sending properly.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Get the device type from MODULE_BRINGUP_REQ command response.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move btmrvl hdev registration code out of btmrvl_add_card().
New function btmrvl_register_hdev() is added.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MODULE_BRINGUP_REQ command response returns success with
either 0x00 or 0x0c.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is mostly cleanup. There is only one caller and it just checks for
non-zero return values. Still "ret" should be int because we want to return
-EINVAL on errors.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auto sleep mode for btmrvl driver is not enabled by default.
This patch enables auto sleep mode when card is probed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Marvell Bluetooth driver is full of Enter/Leave debug statements and
all of them are really pointless and only clutter the code. Seems to be
some left-overs when they ported the driver from Windows. For the Linux
driver lets remove these.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After fixing the driver to use skb_put properly for their HCI commands
only a few compiler warnings are left. Add proper casting for them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Marvell driver has some weird quirks on how to construct proper SKBs
with Bluetooth HCI commands. Fix it to use skb_put properly and also
use hci_opcode_pack instead of self-crafted macro.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make the module description entries for the core and also the Marvell
SDIO driver match common practive inside the Bluetooth subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Marvell core Bluetooth driver has various weird casting and unneeded
braces in its code that makes it hard to read. Remove all of these to
make the code a little bit simpler.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
/debug/btmrvl/config/
/debug/btmrvl/status/
See Documentation/btmrvl.txt for details.
This patch incorporates a lot of comments given by
Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre.
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver provides basic definitions and library functions to
support Marvell Bluetooth enabled devices, such as 88W8688 WLAN/BT
combo chip.
This patch incorporates a lot of comments given by
Nicolas Pitre <nico@marvell.com>. Many thanks to Nicolas Pitre.
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Petri Gynther
Bing Zhao
Amitkumar Karwar
Marcel Holtmann
Daniel Drake
Andrei Emeltchenko
David Herrmann
Tejun Heo
Paul Gortmaker
David Vrabel
Dan Carpenter