According to the API, you may only call clk_get_rate() after actually
enabling it.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: a5fd9139f7 ("w1: add 1-wire master driver for i.MX27 / i.MX31")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The w1 master driver includes a complete open drain emulation
reimplementation among other things.
This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.
When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.
As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.
w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.
The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.
To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.
We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the one wire DS2482 master driver with a module option that allows support
for PPM/SPU/1WS interface modes to be requested. This allows support of chips
that require one or more of these features such as the DS28E05.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1: ds1wm: silence interrupts on HW before claiming the interrupt.
This way avoid possible invalid interrupts in the initialization phase.
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
o Make endian clean, make HW-endianness configurable.
o Use ioread*, iowrite* instead of __raw_readb,__raw_writeb
to also use memory-barriers when accessing HW-registers.
We do not want reordering to happen here.
Both changes are tightly coupled, so I do them in one patch
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace incorrect register offsett calculation by
direct configuration of bus_shift in mfd-cell.
Indirect definition of address-shift by resource size
was unobvious and was wrong (should have used a binary log).
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the omap_hdq
driver ignores it and always returns -ENXIO. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error.
Print error message and propagate the return value of
platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other subsystems we should be able to define slave devices outside
of the w1 directory. To do this we move public facing interface
definitions to include/linux/w1.h and rename the internal definition
file to w1_internal.h.
As w1_family.h and w1_int.h contained almost entirely public
driver interface definitions we simply removed these files and
moved the remaining definitions into w1_internal.h.
With this we can now start to move slave devices out of w1/slaves and
into the subsystem based on the function they implement, again like
other drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Structures and functions should be ordered such that forward declaration
use is minimized.
MODULE_* macros should immediately follow the structures and functions
upon which they act.
Remaining MODULE_* macros should be at the end of the file in
alphabetical order.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only use of assert() is in matrox_w1.c and is used to check the input
to probe() from the PCI subsystem for NULL values, these are guaranteed
to be populated and no other PCI driver makes this check, remove this.
As this was the only definition in w1_log.h, remove this also.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kmemdup rather than duplicating its implementation.
Generated by: scripts/coccinelle/api/memdup.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ds2490 driver was doing USB transfers from / to buffers on a stack.
This is not permitted and made the driver non-working with vmapped stacks.
Since all these transfers are done under the same bus_mutex lock we can
simply use shared buffers in a device private structure for two most common
of them.
While we are at it, let's also fix a comparison between int and size_t in
ds9490r_search() which made the driver spin in this function if state
register get requests were failing.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error returned by '_omap_hdq_reset()', free resources as done
elsewhere in this function.
This patch slighly changes the semantic of the code. It now propagates the
error code returned by '_omap_hdq_reset()' instead of returning -EINVAL
unconditionally.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e93762bbf6 ("w1: masters: omap_hdq: add support for 1-wire
mode") added a statement to clear the hdq_irqstatus flags in
hdq_read_byte().
If the hdq reading process is scheduled slowly or interrupts are
disabled for a while the hardware read activity might already be
finished on entry of hdq_read_byte(). And hdq_isr() already has set the
hdq_irqstatus to 0x6 (can be seen in debug mode) denoting that both, the
TXCOMPLETE and RXCOMPLETE interrupts occurred in parallel.
This means there is no need to wait and the hdq_read_byte() can just
read the byte from the hdq controller.
By resetting hdq_irqstatus to 0 the read process is forced to be always
waiting again (because the if statement always succeeds) but the
hardware will not issue another RXCOMPLETE interrupt. This results in a
false timeout.
After such a situation the hdq bus hangs.
Link: http://lkml.kernel.org/r/b724765f87ad276a69625bc19806c8c8844c4590.1469513669.git.hns@goldelico.com
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit enables the active pullup (APU bit) by default for
the DS2482 1-Wire master.
>From the DS2482 datasheet:
"The APU bit controls whether an active pullup (controlled slew-rate
transistor) or a passive pullup (Rwpu resistor) will be used to drive
a 1-Wire line from low to high. When APU = 0, active pullup is disabled
(resistor mode). Active Pullup should always be selected unless there is
only a single slave on the 1-Wire line."
According to the module author, Ben Gardner:
"It doesn't look like active pullup would cause any hurt if there
is only a single slave."
And my tests with multiple and single slaves on 1-Wire bus
confirms that.
This active pullup can be manually disabled using the introduced
module parameter:
active_pullup = 0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hdq_usecount was set to zero after a successful read, so
omap_hdq_put could not properly free resources which leads
e.g. to increasing usecounts in lsmod output
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's stop using legacy platform driver hooks for power management and
switch to using the standard dev_pm_ops-based hooks.
Also, instead of guarding PM methods with #ifdef CONFIG_PM annotate them
as __maybe_unused as it provides better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use module_pci_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pci_register_driver(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { pci_unregister_driver(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pci_driver;
@@
-module_exit(e);
+module_pci_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add i2c alias to enable autoloading of the module for device specified
in device-tree.
Signed-off-by: Ludek Hlavacek <ludek_h@seznam.cz>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a new
subsystem, "coresight" has been added. Full details are in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSODosACgkQMUfUDdst+ykSNwCfcqx1Z3rQzbLwSrR2sa1fV3Zb
yEAAniJoLZ4ZkoQK4/1ozsFc31q+gXNm
=/epr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This driver has no 'compatible' string and so is not found when
using device-tree.
Add one with value to match
hdqw1w: 1w@480b2000 {
device in omap3.dtsi.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adjust the bulk message timeout to the other ones (1000ms). Otherwise the
following dmesg errors can be seen on a Raspberry Pi:
[ 31.492386] Failed to read 1-wire data from 0x81: err=-110.
[ 31.504168] 0x81: count=-110, status:
[ 31.613404] Failed to read 1-wire data from 0x81: err=-110.
[ 31.621915] 0x81: count=-110, status:
[ 43.260968] Failed to read 1-wire data from 0x81: err=-110.
[ 43.270998] 0x81: count=-110, status:
[ 43.379959] Failed to read 1-wire data from 0x81: err=-110.
[ 43.388854] 0x81: count=-110, status:
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the "masters"
subdirectory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the read/write bit operations
takes from 60 us to 120 us.
This patch optimizes mxc_w1_ds2_touch_bit() function to use proper
value for such delay. Nevertheless, a small margin for the timeout has
been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a software reset for 1-Wire module at driver startup.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the reset procedure and
"presence" pulse takes 511 and 512 us, respectively. Measurement for
i.MX27 is about 1100 us. There is no need to wait Reset+Presence
more than this time.
This patch optimizes mxc_w1_ds2_reset_bus() function to use proper
value for delay after w1 bus reset. Nevertheless, a small margin for
the timeout has been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W1 reset_bus() should return zero if slave device is present.
This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, __raw_{read,write}b() functions was be replaced with
simple {read,write}b() variants.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove old and currently wrong address of the FSF from license
parts of the code.
- Remove unused #include and sort remaining headers alphabetically.
- Remove unised definitions.
- Add definitions for bit-fields.
- Add missing module owner field.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix mxc_w1_ds2_reset_bus() return value.
According to i.MX reference manual, "presence status" reflected
in the bit 6 of control register.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configuration for masters and slaves is included only if W1 symbol
enabled, so no reason to check it once more.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_get_gpio() might return -EPROBE_DEFER meaning that the driver
providing the gpio isn't ready yet. If that happens for the first gpio
the resulting kernel output without this patch is:
w1-gpio somename: Failed to parse DT
platform somename: Driver w1-gpio requests probe deferral
The first message is misleading and so is suppressed with this patch.
Further if determining the gpio to switch the external pullup yields
-EPROBE_DEFER this error should be passed back to the caller instead of
just continuing without pullup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts ds1wm.c from commit d3a8a9dbb9.
Of the three files changed ds1wm.c ds2490.c and w1_netlink.c, it turns out
ds1wm.c was locking bus_mutex, but inside the loop and I missed it.
Reverting ds1wm.c to the previous version.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bus_mutex needs to be taken to serialize access to a specific bus.
netlink wasn't updated when bus_mutex was added and was calling
without that lock held, and not all of the masters were holding the
bus_mutex in a search. This was causing the ds2490 hardware to stop
responding when both netlink and /sys slaves were executing bus
commands at the same time.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware search was failing without the COMM_RST flag. Enabled
the flag and rewrote the function to handle more than one buffer of
results and to continuing where the search left off. Remove hardware
search note from the limitations now that it works. The "w1: ds2490
USB setup fixes" change went from 23.16 seconds to about 3 seconds,
this takes the time for the search down to .307346 seconds.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling usb_reset_configuration after usb_set_interface resets the
interface that was just selected, so call reset first.
Using alternative 3 greatly speeds the one wire search.
alt 0 or 1, 10ms int, 23.16 seconds
alt 2 or 3, 1ms int, 2.99 to 3.05 seconds
Use usb_interrupt_msg not usb_bulk_msg as it is an interrupt pipe
(bulk worked, it was just technically the wrong call).
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a #define for the usb vendor request type, clear the status
byte and use that instead of a magic offset in checking if idle.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Potyra
Linus Walleij
Greg Kroah-Hartman
Andrew Worsley
Johannes Poehlmann
Arvind Yadav
Gustavo A. R. Silva
Andrew F. Davis
Wei Yongjun
Maciej S. Szmigiero
Christophe JAILLET
H. Nikolaus Schaller
Mariusz Bialonczyk
Andreas Kemnade
Dmitry Torokhov
Vignesh R
Linus Torvalds
Masanari Iida
Vaishali Thakkar
Krzysztof Kozlowski
Ludek Hlavacek
Fabian Frederick
NeilBrown
Alexander Stein
Wolfram Sang
Fjodor Schelichow
Alexander Shiyan
Uwe Kleine-König
David Fries
Evgeny Boger