First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
We get support for three new 32-bit SoC platforms this time. The amount
of changes in arch/arm for any of them is miniscule, as all the
interesting code is in device driver subsystems (irqchip, clk, pinctrl,
...) these days. I'm listing them here, as the addition of the Kconfig
statement is the main relevant milestone for a new platform. In each
case, some drivers are are shared with existing platforms, while
other drivers are added for v4.7 as well, or come in a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/ triggered the submission, but the
code comes from IBM's OpenPOWER team rather than the team at
Facebook. There are still a lot more drivers that need to get added
over time, and I hope both teams can work together on that.
- OXNAS is an old platform for Network Attached Storage devices
from Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions.
The product lineup was subsequently part of PLX, Avago and now the
new Broadcom Ltd. https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU. We now support various NOMMU platforms,
so adding a new one is fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain Lemieux
are now maintaining the platform. This is an older ARM9 based
platform from NXP (not Freescale), but it remains in use in embedded
markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for both
32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk of
the actual SoC code changes in arch/arm, but there isn't a lot of
that either.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oFu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"We get support for three new 32-bit SoC platforms this time.
The amount of changes in arch/arm for any of them is miniscule, as all
the interesting code is in device driver subsystems (irqchip, clk,
pinctrl, ...) these days. I'm listing them here, as the addition of
the Kconfig statement is the main relevant milestone for a new
platform. In each case, some drivers are are shared with existing
platforms, while other drivers are added for v4.7 as well, or come in
a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/
triggered the submission, but the code comes from IBM's OpenPOWER
team rather than the team at Facebook. There are still a lot more
drivers that need to get added over time, and I hope both teams can
work together on that.
- OXNAS is an old platform for Network Attached Storage devices from
Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions. The product lineup was subsequently part of PLX,
Avago and now the new Broadcom Ltd.
https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU.
We now support various NOMMU platforms, so adding a new one is
fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain
Lemieux are now maintaining the platform.
This is an older ARM9 based platform from NXP (not Freescale), but
it remains in use in embedded markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for
both 32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk
of the actual SoC code changes in arch/arm, but there isn't a lot
of that either"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: ARM/Amlogic: add co-maintainer, misc. updates
MAINTAINERS: add ARM/NXP LPC32XX SoC specific drivers to the section
MAINTAINERS: add new maintainers of NXP LPC32xx SoC
MAINTAINERS: move ARM/NXP LPC32xx record to ARM section
arm: Add Aspeed machine
ARM: lpc32xx: remove duplicate const on lpc32xx_auxdata_lookup
ARM: lpc32xx: remove leftovers of legacy clock source and provider drivers
ARM: lpc32xx: remove reboot header file
ARM: dove: Remove CLK_IS_ROOT
ARM: orion5x: Remove CLK_IS_ROOT
ARM: mv78xx0: Remove CLK_IS_ROOT
ARM: davinci: da850: use clk->set_parent for async3
ARM: davinci: Move clock init after ioremap.
MAINTAINERS: Update ARM Versatile Express platform entry
ARM: vexpress/mps2: introduce MPS2 platform
MAINTAINERS: add maintainer entry for ARM/OXNAS platform
ARM: Add new mach-oxnas
irqchip: versatile-fpga: add new compatible for OX810SE SoC
ARM: uniphier: correct the call order of of_node_put()
MAINTAINERS: fix stale TI DaVinci entries
...
Traditionally we've had two separate branches for cleanups and non-critical
bug fixes, but both of these got smaller with each release and the differences
are rather unclear now, so it seems more appropriate to have a combined
branch.
The most notably change is for OMAP, which gets a small rework to simplify
handling of the AUXDATA mechanism used on machines that are not completely
DT based yet, along with other work that is used as preparation for dropping
the legacy board files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=au7y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups and fixes from Arnd Bergmann:
"Traditionally we've had two separate branches for cleanups and
non-critical bug fixes, but both of these got smaller with each
release and the differences are rather unclear now, so it seems more
appropriate to have a combined branch.
The most notable change is for OMAP, which gets a small rework to
simplify handling of the AUXDATA mechanism used on machines that are
not completely DT based yet, along with other work that is used as
preparation for dropping the legacy board files"
* tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
* pm-cpufreq: (63 commits)
intel_pstate: Clean up get_target_pstate_use_performance()
intel_pstate: Use sample.core_avg_perf in get_avg_pstate()
intel_pstate: Clarify average performance computation
intel_pstate: Avoid unnecessary synchronize_sched() during initialization
cpufreq: schedutil: Make default depend on CONFIG_SMP
cpufreq: powernv: del_timer_sync when global and local pstate are equal
cpufreq: powernv: Move smp_call_function_any() out of irq safe block
intel_pstate: Clean up intel_pstate_get()
cpufreq: schedutil: Make it depend on CONFIG_SMP
cpufreq: governor: Fix handling of special cases in dbs_update()
cpufreq: intel_pstate: Ignore _PPC processing under HWP
cpufreq: arm_big_little: use generic OPP functions for {init, free}_opp_table
cpufreq: tango: Use generic platdev driver
cpufreq: Fix GOV_LIMITS handling for the userspace governor
cpufreq: mvebu: Move cpufreq code into drivers/cpufreq/
cpufreq: dt: Kill platform-data
mvebu: Use dev_pm_opp_set_sharing_cpus() to mark OPP tables as shared
cpufreq: dt: Identify cpu-sharing for platforms without operating-points-v2
cpufreq: governor: Change confusing struct field and variable names
cpufreq: intel_pstate: Enable PPC enforcement for servers
...
compatible string if no exact match based on the IO address is found.
This leaves out the need to patch auxdata for each driver when adding
new SoCs. And it also reprotedly fixes the issue of passing auxdata
to a child if the parent instantiates the child from DT as discussed
in the "[PATCH] of/platform: Allow secondary compatible match in
of_dev_lookup" mailing list thread.
As a minimal use case, let's also convert omap pinctrl auxdatato
use a generic match.
There is no need to get this in to the v4.6-rc cycle and it can wait
for v4.7 merge window. Note that these changes have now been sitting
in Linux next for about two weeks so far as I wanted to make sure no
new issues are popping up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXKjVmAAoJEBvUPslcq6VzNaIQAKBW4SoVCpUnz8U7Vb6drVmk
kNuXn317CJQIJSPYuncQkmnPPDqvRBB16offmWI2z31R2p8azuf4kTkroqGrIP2+
ZuXyuxNc3IczxMiWjVN3SKA7/h4fRM+J8IN8AHHf/DAcFOc0Dz1muMhkEX3otT+/
qFn85iBreeAaNnW9eViZ+lvz6wSYlhrHAPrW3jHJM1Q11OTi45vymS82iU4ztcXo
zotDxSLaMcQJNAb6wF553JhzwL8G1bM9Ab1b5+vsOVQ/y/wWY+b/maGePUQCWiVX
cggYoa/0gDmBGAUdLq1GvVTg4HHIEaO0ysrioMlHmOkTf7KXXiKITZTX98FE39rL
xH/2nkechWV8yWPwhZktjASzcImqItcMdS3axFgdHnV7fpho2an/80Ekod401/Bh
wIJ48gZxPAyshjr+e8xhyHRdEauVmUYvdiUS/Gv8dEvJJnBqVFYcLd/FNCp43j5X
G7RQITG0pK7i0xwX+9vNOrD5CzfWCSLYw6iMnMnReMdnw9PUwbYLaiWTuoyC6Pmd
B9zMkqOzdael6fFuQvRi9ZOEoSK5A3EpLWrvXzrS4nXy1dOa2eDpuxoRkAKACVMf
wyANAn3YK1pQwtnoGRsdNk98zjMX2o8H1G0XKB0QewNa0zlNhGIUsAiZYX4H/drg
taAbzAUSLloDcHnyQgis
=T39l
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/auxdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "non urgent auxdata fix for v4.7 merge window" from Tony Lindgren:
Device tree auxdata handling fix that allows a match based on the
compatible string if no exact match based on the IO address is found.
This leaves out the need to patch auxdata for each driver when adding
new SoCs. And it also reprotedly fixes the issue of passing auxdata
to a child if the parent instantiates the child from DT as discussed
in the "[PATCH] of/platform: Allow secondary compatible match in
of_dev_lookup" mailing list thread.
As a minimal use case, let's also convert omap pinctrl auxdatato
use a generic match.
There is no need to get this in to the v4.6-rc cycle and it can wait
for v4.7 merge window. Note that these changes have now been sitting
in Linux next for about two weeks so far as I wanted to make sure no
new issues are popping up.
* tag 'omap-for-v4.7/auxdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
Let's pass the slot names in pdata like the legacy code does.
Once we have a generic DT binding for the slot names we can
switch to that.
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Before we start removing omap3 legacy booting support, let's make n900
DT booting behave the same way for ir-rx51 as the legacy booting does.
For now, we need to pass pdata to the ir-rx51 driver. This means that
the n900 tree can move to using DT based booting without having to carry
all the legacy platform data with it when it gets dropped from the mainline
tree.
Note that the ir-rx51 driver is currently disabled because of the
dependency to !ARCH_MULTIPLATFORM. This will get sorted out later
with the help of drivers/pwm/pwm-omap-dmtimer.c. But first we need
to add chained IRQ support to dmtimer code to avoid introducing new
custom frameworks.
So let's just pass the necessary dmtimer functions to ir-rx51 so we
can get it working in the following patch.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6rQp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes for v4.6-rc cycle" from Tony Lindgren:
Fixes for omaps for v4.6-rc cycle:
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
* tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
For the DRA7xx platform, add IP block data for the McASP, PWMSS,
and GPTimer12 IP blocks. Add lock and unlock functions for the
RTC IP blocks on the DRA7xx, AM33xx, and AM43xx devices. And add
a fix for the hwmod core for device driver unbind operations for
IP blocks with hardreset lines.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.7/20160410132119/
Note that the testbed here does not have the DRA7xx board included yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=k5TK
-----END PGP SIGNATURE-----
Merge tag 'for-v4.7/omap-hwmod-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.7/soc
ARM: OMAP2+: first set of hwmod changes for v4.7
For the DRA7xx platform, add IP block data for the McASP, PWMSS,
and GPTimer12 IP blocks. Add lock and unlock functions for the
RTC IP blocks on the DRA7xx, AM33xx, and AM43xx devices. And add
a fix for the hwmod core for device driver unbind operations for
IP blocks with hardreset lines.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v4.7/20160410132119/
Note that the testbed here does not have the DRA7xx board included yet.
that broke when we added runtime based SoC revision detection earlier.
It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.
Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.
Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0X4E
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.6-rc2" from Tony Lindgren
Fixes for omaps against v4.6-rc2, mostly to fix suspend for beagle-x15
that broke when we added runtime based SoC revision detection earlier.
It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.
Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.
Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.
* tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (198 commits)
Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
ARM: OMAP: Catch callers of revision information prior to it being populated
ARM: dts: dra7: Correct clock tree for sys_32k_ck
ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
Linux 4.6-rc2
v4l2-mc: avoid warning about unused variable
Convert straggling drivers to new six-argument get_user_pages()
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
net: mvneta: fix changing MTU when using per-cpu processing
...
Move NAND specific device tree parsing to NAND driver.
The NAND controller node must have a compatible id, register space
resource and interrupt resource.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Deprecate nand register passing via platform data and use
gpmc_omap_get_nand_ops() instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Depending on timing during the resume path from off mode on 36xx, we may
see external aborts. These seem to be caused by the following:
- OMAP3 Advisory 1.62 "MPU Cannot Exit from Standby" says we need to
disable intc autoidle before WFI
- DM3730 Advisory 1.106 "MPU Leaves MSTANDBY State Before IDLEREQ of
Interrupt Controller is Released" says we need to wait before
accessing intc
omap3_intc_resume_idle restores the intc autoidle for all resume paths,
however in the resume path from off mode only it is also being restored
by omap_intc_restore_context before this call to omap3_intc_resume_idle
happens. The second restore of the intc autoidle in this path is what
appears to be causing the external abort so for the off mode resume path
let's rely on omap_intc_restore_context to restore intc autoidle, and
for all other paths let omap3_intc_resume_idle handle it as it is now.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
FROZEN hotplug notifiers are not handled and do not have to be. Insert
a comment to remember that the lack of the FROZEN transitions is no
accident.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Open Switch Retention(OSWR) is a retention state which is unsupported
in DRA7 SoC. This state is achieved when power state is set to
retention and logic power state is set to OFF.
Even though DRA7 architecture is a OMAP derivative, none of the
powerdomains are actually implemented to achieve OSWR in the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the power domain is in "ON" state, the memories should be always
in "ON", even though the hardware register allows other states to be
written, wrong states may confuse certain hardware blocks.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Erratum i892 as will be documented in the upcoming G or later revision
of DRA7xx/ AM57xx errata documentation (SPRZ398F) states that L3 clock
needs to be kept active all the time to ensure that asymmetric aging
degradation is minimal and within the design allowed margin.
By allowing core domain to transition to INA and allowing L3 clock to be
turned off for extended periods of time, there is a risk of functional
issues and device failure as a result.
Ref: http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The directory arch/arm/mach-omap2 is only selected for compilation if
CONFIG_ARCH_OMAP2PLUS is selected. CONFIG_ARCH_OMAP2PLUS itself is a
silent option and all machines selecting this option are multiplatform
devices. As a consequence checks for CONFIG_ARCH_MULTIPLATFORM as well
as CONFIG_ARCH_OMAP2PLUS within that directory are superfluous and can
be removed.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For DRA7xx platforms, add a workaround for missed timer interrupts
that appears to be due to an integration bug (erratum i874)
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-fixes-b-for-v4.6-rc/20160413020850/
(The DRA7xx board here has not yet been added into the testbed.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6XvG
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes
ARM: OMAP2+: clockdomain: another fix for v4.6-rc
For DRA7xx platforms, add a workaround for missed timer interrupts
that appears to be due to an integration bug (erratum i874)
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-fixes-b-for-v4.6-rc/20160413020850/
(The DRA7xx board here has not yet been added into the testbed.)
The omap_hwmod _enable() function can return success without setting
the hwmod state to _HWMOD_STATE_ENABLED for IPs with reset lines when
all of the reset lines are asserted. The omap_hwmod _idle() function
also performs a similar check, but after checking for the hwmod state
first. This triggers the WARN when pm_runtime_get and pm_runtime_put
are invoked on IPs with all reset lines asserted. Reverse the checks
for hwmod state and reset lines status to fix this.
Issue found during a unbind operation on a device with reset lines
still asserted, example backtrace below
------------[ cut here ]------------
WARNING: CPU: 1 PID: 879 at arch/arm/mach-omap2/omap_hwmod.c:2207 _idle+0x1e4/0x240()
omap_hwmod: mmu_dsp: idle state can only be entered from enabled state
Modules linked in:
CPU: 1 PID: 879 Comm: sh Not tainted 4.4.0-00008-ga989d951331a #3
Hardware name: Generic OMAP5 (Flattened Device Tree)
[<c0018e60>] (unwind_backtrace) from [<c0014dc4>] (show_stack+0x10/0x14)
[<c0014dc4>] (show_stack) from [<c037ac28>] (dump_stack+0x90/0xc0)
[<c037ac28>] (dump_stack) from [<c003f420>] (warn_slowpath_common+0x78/0xb4)
[<c003f420>] (warn_slowpath_common) from [<c003f48c>] (warn_slowpath_fmt+0x30/0x40)
[<c003f48c>] (warn_slowpath_fmt) from [<c0028c20>] (_idle+0x1e4/0x240)
[<c0028c20>] (_idle) from [<c0029080>] (omap_hwmod_idle+0x28/0x48)
[<c0029080>] (omap_hwmod_idle) from [<c002a5a4>] (omap_device_idle+0x3c/0x90)
[<c002a5a4>] (omap_device_idle) from [<c0427a90>] (__rpm_callback+0x2c/0x60)
[<c0427a90>] (__rpm_callback) from [<c0427ae4>] (rpm_callback+0x20/0x80)
[<c0427ae4>] (rpm_callback) from [<c0427f84>] (rpm_suspend+0x138/0x74c)
[<c0427f84>] (rpm_suspend) from [<c0428b78>] (__pm_runtime_idle+0x78/0xa8)
[<c0428b78>] (__pm_runtime_idle) from [<c041f514>] (__device_release_driver+0x64/0x100)
[<c041f514>] (__device_release_driver) from [<c041f5d0>] (device_release_driver+0x20/0x2c)
[<c041f5d0>] (device_release_driver) from [<c041d85c>] (unbind_store+0x78/0xf8)
[<c041d85c>] (unbind_store) from [<c0206df8>] (kernfs_fop_write+0xc0/0x1c4)
[<c0206df8>] (kernfs_fop_write) from [<c018a120>] (__vfs_write+0x20/0xdc)
[<c018a120>] (__vfs_write) from [<c018a9cc>] (vfs_write+0x90/0x164)
[<c018a9cc>] (vfs_write) from [<c018b1f0>] (SyS_write+0x44/0x9c)
[<c018b1f0>] (SyS_write) from [<c0010420>] (ret_fast_syscall+0x0/0x1c)
---[ end trace a4182013c75a9f50 ]---
While at this, fix the sequence in _shutdown() as well, though there
is no easy reproducible scenario.
Fixes: 747834ab83 ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the hwmod data for GPTimer 12. GPTimer 12 is present in
WKUPAON power domain and is clocked from a secure 32K clock.
GPTimer 12 serves as a secure timer on HS devices, but is
available for kernel on regular GP devices.
The hwmod link is registered only on GP devices. The hwmod data
also reused the existing timer class instead of reintroducing
the identical dra7xx_timer_secure_sysc class which was dropped
in commit edec178633 ("ARM: DRA7: hwmod: Fix the hwmod class
for GPTimer4").
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hook omap_hwmod_rtc_unlock/lock functions into RTC hwmod,
so that SYSCONFIG register is updated properly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hook omap_hwmod_rtc_unlock/lock functions into RTC hwmod,
so that SYSCONFIG register is updated properly
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
RTC IP have kicker feature which prevents spurious writes to its registers.
In order to write into any of the RTC registers, KICK values has to be
written to KICK registers. Also, RTC busy flag needs to be polled for
non-TC registers as well, without which update is not proper and confirmed
it by testing on DRA7-evm.
Introduce omap_hwmod_rtc_unlock/lock functions, which writes into these
KICK registers inorder to lock and unlock RTC registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[paul@pwsan.com: fixed subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod entries for the PWMSS on DRA7.
Set l4_root_clk_div as the main_clk of PWMSS. It is fixed-factored clock
equal to L4PER2_L3_GICLK/2(l3_iclk_div/2).
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Do not add eQEP, ePWM and eCAP hwmod entries]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[paul@pwsan.com: fixed sparse warnings; added missing comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add missing data for all McASP ports for the dra7 family
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Errata Title:
i874: TIMER5/6/7/8 interrupts not propagated
Description:
When TIMER5, TIMER6, TIMER7, or TIMER8 clocks are enabled
(CM_IPU_TIMER5/6/7/8_CLKCTRL[0:1]MODULEMODE=0x2:ENABLE) and the CD-IPU
is in HW_AUTO mode (CM_IPU_CLKSTCTRL[0:1]CLKTRCTRL=0x3:HW_AUTO) the
corresponding TIMER will continue counting, but enabled interrupts
will not be propagated to the destinations (MPU, DSP, etc) in the
SoC until the TIMER registers are accessed from the CPUs (MPU, DSP
etc.). This can result in missed timer interrupts.
Workaround:
In order for TIMER5/6/7/8 interrupts to be propagated and serviced
correctly the CD_IPU domain should be set to SW_WKUP mode
(CM_IPU_CLKSTCTRL[0:1]CLKTRCTRL=0x2:SW_WKUP).
The above workaround is achieved by switching the IPU clockdomain
flags from HWSUP_SWSUP to SWSUP only.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_rev is used to detect various SoC types, however any misuse of
the usage by invoking it earlier than it being populated will result
in invalid results. Lets flag them as early as possible to prevent
unintended side effects taking place. We get 0 if it is uninitialized
and -1 when detection is done using device tree (as the case was for
DRA7 as the case was prior to commit 06c2d368fc ("ARM: OMAP: DRA7:
Make use of omap_revision information for soc_is* calls")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When commit 06c2d368fc ("ARM: OMAP: DRA7: Make use of omap_revision
information for soc_is* calls") introduced SoC check using
omap_revision, it missed providing DRA7 as class for initializing
the omap_version variable. Without doing this, soc_is_dra7xx() will
fail and as a result, omap4_pm_init_early never initializes the dra7
erratum for CPU power state. This causes the suspend path to fail
on DRA7 devices.
Fixes: 06c2d368fc ("ARM: OMAP: DRA7: Make use of omap_revision information for soc_is* calls")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 has no SAR region for automated save and restore of wakeupgen,
which does not make real since the SoC really does not do legacy OFF
mode anymore. Further wakeupgen should never loose context in CSWR
retention mode for MPU domain on DRA7 since that is the deepest state
we will enter.
So, just skip, instead of oopsing as follows while attemptint to enter
suspend on BeagleBoard-X15.
[ 55.589771] Unable to handle kernel paging request at virtual address 00002684
[ 55.589771] pgd = ec69c000
[...]
[ 55.589771] [<c0123cc8>] (irq_notifier) from [<c015ad70>] (notifier_call_chain+0x4c/0x8c)
[ 55.589771] [<c015ad70>] (notifier_call_chain) from [<c021469c>] (cpu_cluster_pm_enter+0x2c/0x78)
[ 55.589771] [<c021469c>] (cpu_cluster_pm_enter) from [<c0514508>] (syscore_suspend+0xb8/0x31c)
[ 55.589771] [<c0514508>] (syscore_suspend) from [<c0197d24>] (suspend_devices_and_enter+0x308/0x9e4)
[ 55.589771] [<c0197d24>] (suspend_devices_and_enter) from [<c0198a40>] (pm_suspend+0x640/0x75c)
[ 55.589771] [<c0198a40>] (pm_suspend) from [<c0196bcc>] (state_store+0x64/0xb8)
[ 55.589771] [<c0196bcc>] (state_store) from [<c0307914>] (kernfs_fop_write+0xc0/0x1bc)
[ 55.589771] [<c0307914>] (kernfs_fop_write) from [<c028ac80>] (__vfs_write+0x1c/0xd8)
[ 55.589771] [<c028ac80>] (__vfs_write) from [<c028bb70>] (vfs_write+0x90/0x16c)
[ 55.589771] [<c028bb70>] (vfs_write) from [<c028c890>] (SyS_write+0x44/0x9c)
[ 55.589771] [<c028c890>] (SyS_write) from [<c0107840>] (ret_fast_syscall+0x0/0x1c)
[...]
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Silicon Rev 2.0 is a minor variant of Rev 1.0. Rev 2.0 is an incremental revision
with various fixes including the following:
- Reset logic fixes
- Few asymmetric aging logic fixes
- Ethernet speed fixes
- EDMA fixes for McASP
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following commits:
commit 3fa609755c ("ARM: omap2: restore OMAP4 barrier behaviour")
commit f746929ffd ("Revert "ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688"")
and
commit ea827ad5ff ("ARM: DRA7: Provide proper IO map table")
came in around the same time, unfortunately this seem to have missed
initializing the barrier for DRA7 platforms - omap5_map_io was reused
for dra7 till it was split out by the last patch. barrier_init
needs to be hence carried forward as it is valid for DRA7 family of
processors as they are for OMAP5.
Fixes: ea827ad5ff ("ARM: DRA7: Provide proper IO map table")
Cc: stable@vger.kernel.org # v4.1+
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a longstanding bug in the hwmod code that could cause
hardware SYSCONFIG register values to not match the kernel's
idea of what they should be, and that could result in lower
performance during IP block idle entry.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-fixes-a-for-v4.6-rc/20160326231727/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MWxZ
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes
ARM: OMAP2+: first hwmod fix for v4.6-rc
Fix a longstanding bug in the hwmod code that could cause
hardware SYSCONFIG register values to not match the kernel's
idea of what they should be, and that could result in lower
performance during IP block idle entry.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-fixes-a-for-v4.6-rc/20160326231727/
Commit 127500ccb7 ("ARM: OMAP2+: Only write the sysconfig on idle
when necessary") talks about verification of sysconfig cache value before
updating it, only during idle path. But the patch is adding the
verification in the enable path. So, adding the check in a proper place
as per the commit description.
Not keeping this check during enable path as there is a chance of losing
context and it is safe to do on idle as the context of the register will
never be lost while the device is active.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org> # 3.12+
Fixes: commit 127500ccb7 "ARM: OMAP2+: Only write the sysconfig on idle when necessary"
[paul@pwsan.com: appears to have been caused by my own mismerge of the
originally posted patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP, uniphier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ynNj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
A few simple cleanups across multiple platforms, not much standing out:
- lpc32xx removes its private implementation of the clk API, after
generic code was merged in 4.5
- all unused Makefile.boot files get removed
- a number of simplifications for shmobile
- asm/clkdev.h gets replaced with the asm-generic version after
all mach/clkdev.h implementations are gone
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAVu67NGCrR//JCVInAQJoQw/+Mvbsb57ueA6Ao7l4/UpsNayKIuYZlrrQ
afa6KMYzqPuQ9hWYAFMNM9amIHMX8aqoZTL29soezLYlcpGxeN49AJ1bXX+Qci8r
DAiU2Z6SX3qXo396Fg8VTDNSfn3SvEPnp6X2GcaxrB349jeGJqFeABEnPcVkBBtE
18wxO1AbtsbOpwaGDCnndJOc0vYuRfkUAW0+3379jI7IGrZzq38sTGdmFmZ0HYCv
DWFkUU/DPKVPnRIkZUCljUQXYYYiuvpZUXyZZPRUT/k6ujXmtjZJij9CAJkm9f0e
dyv3aYIlp8+jSdWoT+58eSAsihyGPEwfgDE3xYxKm2ENxGgS1HQJYNDAm/j3Kj4J
iX98bdBxKzZsHb64jNOeOVxs0xVvHSolo0oFM9sSIMgZ2hQZScXAj24Wd1sHyF0Y
K+ru5g7oHQoaHLsyRn8buN8F+0ATv1A8Wecy6avAYvKYHhMV7WrgbiJlRGmS3PUH
8XiTNsQbiUJIvFafj38yStpPLc8jpf8LcAdql0T+JyMCd8+Ee+bpaswvJysmWKg7
12G7xaUyLhUP5DZn3mMM8UyI1/yoUk63igsT7eUsGLfLzSL25X1ATh24Cb8Gwf4f
+HIv21zbUbgRrN3u+N2QRU46BESlfSp68Gjrth3p+1nvHISZpnEJ9ujcpRtCY7Ik
uBSxUT21VN8=
=ZTl9
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A few simple cleanups across multiple platforms, not much standing
out:
- lpc32xx removes its private implementation of the clk API, after
generic code was merged in 4.5
- all unused Makefile.boot files get removed
- a number of simplifications for shmobile
- asm/clkdev.h gets replaced with the asm-generic version after all
mach/clkdev.h implementations are gone"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: Kconfig: Get rid of old comment
ARM: shmobile: Consolidate SCU mapping code
arm: lpc32xx: remove direct control of GPIOs from shared mach file
arm: lpc32xx: remove selected HAVE_IDE
arm: lpc32xx: switch to common clock framework
ARM: Use generic clkdev.h header
ARM: plat-versatile: Remove unused clock.c file
ARM: netx: remove redundant "depends on ARCH_NETX"
ARM: integrator: remove redundant select in Kconfig
ARM: drop unused Makefile.boot of Multiplatform SoCs
ARM: mvebu: add missing of_node_put()
ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
ARM: shmobile: Typo s/MIPDR/MPIDR/
ARM: shmobile: Add includes providing forward declarations
ARM: shmobile: rcar-gen2: Make rcar_gen2_dma_contiguous static
ARM: mv78xx0: use "depends on" instead of "if" after prompt
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- a number of randconfig warning fixes from Arnd
- various small fixes for OMAP
- one somewhat larger patch to restore the OMAP3 cpuidle
tuning that was lost in a cleanup
- a small regression fix for cns3xxx PCI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YJmM
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- a number of randconfig warning fixes from Arnd
- various small fixes for OMAP
- one somewhat larger patch to restore the OMAP3 cpuidle tuning that
was lost in a cleanup
- a small regression fix for cns3xxx PCI"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
CNS3xxx: Fix PCI cns3xxx_write_config()
MAINTAINERS: unify email addrs for Kevin Hilman
CNS3xxx: remove unused *_VIRT definitions
ARM: OMAP2+: Fix hwmod clock for l4_ls
soc: TI knav_qmss: fix dma_addr_t printing
ARM: prima2: always enable reset controller
ARM: socfpga: hide unused functions
ARM: ux500: fix ureachable iounmap()
ARM: ks8695: fix __initdata annotation
ARM: mvebu: mark mvebu_hwcc_pci_nb as __maybe_unused
ARM: mv78xx0: avoid unused function warning
ARM: orion: only select I2C_BOARDINFO when using I2C
ARM: OMAP2+: Fix out of range register access with syscon_config.max_register
ARM: OMAP3: Add cpuidle parameters table for omap3430
ARM: davinci: make I2C support optional
ARM: davinci: DA8xx+DMx combined kernels need PATCH_PHYS_VIRT
ARM: davinci: avoid unused mityomapl138_pn_info variable
ARM: davinci: limit DT support to DA850
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
...
Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8z8ACgkQMUfUDdst+ym1vwCgnOOCORaZyeQ4QrcxPAK5pHFn
VrMAoNHvDgNYtG+Hmzv25Lgp3HnysPin
=MLRG
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (220 commits)
serial: 8250: describe CONFIG_SERIAL_8250_RSA
serial: samsung: optimize UART rx fifo access routine
serial: pl011: add mark/space parity support
serial: sa1100: make sa1100_register_uart_fns a function
tty: serial: 8250: add MOXA Smartio MUE boards support
serial: 8250: convert drivers to use up_to_u8250p()
serial: 8250/mediatek: fix building with SERIAL_8250=m
serial: 8250/ingenic: fix building with SERIAL_8250=m
serial: 8250/uniphier: fix modular build
Revert "drivers/tty/serial: make 8250/8250_ingenic.c explicitly non-modular"
Revert "drivers/tty/serial: make 8250/8250_mtk.c explicitly non-modular"
serial: mvebu-uart: initial support for Armada-3700 serial port
serial: mctrl_gpio: Add missing module license
serial: ifx6x60: avoid uninitialized variable use
tty/serial: at91: fix bad offset for UART timeout register
tty/serial: at91: restore dynamic driver binding
serial: 8250: Add hardware dependency to RT288X option
TTY, devpts: document pty count limiting
tty: goldfish: support platform_device with id -1
drivers: tty: goldfish: Add device tree bindings
...
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kJw8
-----END PGP SIGNATURE-----
Merge tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
ARM: OMAP2+: critical DRA7xx fix for v4.5-rc
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
* tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce a dt property, ti,no-idle, that prevents an IP to idle at any
point. This is to handle Errata i877, which tells that GMAC clocks
cannot be disabled.
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- Enable runtime revision detection for dra7 to avoid multiple dts
files for various variants
- Add dma_slave_map for omap1/2/3 legacy mode booting
- Add RTC interconnect target data for ti81xx and am43x
- Add custom reset handler for PCIeSS
- Add eDMA interconnect target data for dra7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tJb7
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "omap soc changes for v4.6 merge window" from Tony Lindgren:
SoC related changes for omaps for v4.6 merge window:
- Enable runtime revision detection for dra7 to avoid multiple dts
files for various variants
- Add dma_slave_map for omap1/2/3 legacy mode booting
- Add RTC interconnect target data for ti81xx and am43x
- Add custom reset handler for PCIeSS
- Add eDMA interconnect target data for dra7
* tag 'omap-for-v4.6/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: OMAP2+: DMA: Provide dma_slave_map to omap-dma for legacy boot
ARM: OMAP1: DMA: Provide dma_slave_map to omap-dma
ARM: OMAP: DRA7: Make use of omap_revision information for soc_is* calls
ARM: AM43XX: hwmod: Add rtc hwmod
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
ARM: OMAP2+: hwmod data: Add SSI data for omap36xx
for the v4.5-rc cycle:
- Add back optimized cpuidle parameters for 34xx that were
incorrecly removed earlier with cpuidle cleanup
- Fix SSI for omap36xx to get modem working on N950/N9
- A series of omap hwmod fixes via Paul Walmsley <paul@pwsan.com>
to fix SSI for omap36xx for modem on N950/N9, fix for
OCP2SCP sysconfig idle mode, and reset data for PCIe on
dra7
- Fix out of range register access for omap3 control module
if syscon max_register is initialized like v4.6 will be
doing
- Fix l4_ls interconnect clocks for 81xx, it should always
be sysclk6_ck
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pwoK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap non-urgent fixes for v4.6 merge window" from Tony Lindgren:
Fixes for omaps for v4.6 merge window that are not urgent
for the v4.5-rc cycle:
- Add back optimized cpuidle parameters for 34xx that were
incorrecly removed earlier with cpuidle cleanup
- Fix SSI for omap36xx to get modem working on N950/N9
- A series of omap hwmod fixes via Paul Walmsley <paul@pwsan.com>
to fix SSI for omap36xx for modem on N950/N9, fix for
OCP2SCP sysconfig idle mode, and reset data for PCIe on
dra7
- Fix out of range register access for omap3 control module
if syscon max_register is initialized like v4.6 will be
doing
- Fix l4_ls interconnect clocks for 81xx, it should always
be sysclk6_ck
* tag 'omap-for-v4.6/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix hwmod clock for l4_ls
ARM: OMAP2+: Fix out of range register access with syscon_config.max_register
ARM: OMAP3: Add cpuidle parameters table for omap3430
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
ARM: OMAP2+: hwmod data: Add SSI data for omap36xx
Without this booting t410 can fail randomly with no output
depending on the .config options chosen. Enabling debug_ll
causes the problem to go away. I narrowed this down to USB
by disabling one module at a time.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These patches add RTC support for the AM43xx, and add support for
the DRA7xx eDMA controller's TPCC, TPTC0, and TPTC1 IP blocks.
Also included is a workaround for PRCM hardreset control of the DRA7xx
PCIe subsystem.
Note that I do not have a DRA7xx board, and therefore cannot
test any patches for that SoC family.
Basic build, boot, and PM test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-b-for-v4.6/20160301021258/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW1WdKAAoJEMePsQ0LvSpLoO8P/A05egqdZtbWCte8tK4/E+d1
fdzaev9dC8I6rWlxV6PTFZL8Hw28XtQZDYqV2voRE5nxma1L05Uang2c2tNmO7oH
Qa7pvD/m6vy3A2ZIKgTJeV7Elc5SNEmPQq6/1z1viWni4oUFWrsP1cKPTmUOhTNu
cx6Q2oxkoGlLRmonygJ49da6XShPMIOolDUNfOKFuSmt80RUor2j1Wpu+3wlVZvr
53jSLG8C+RgiUeBT90PUOvI7dAfocOV+G8CnH7/Fnss9+L2skiKwOOUNudGBz3JZ
elAwjyiCkBlo3VGSRk4UarXuzAdCqZqvLSemYZ1JbYT3SbbIWovJ9nX17y7Gl7RT
4KnGW0P+yeYYj9iEwUOs1Yj4DgFTbgkmHqkF2zWPGawjj3AMUKquvYVR1d+Oz3NR
77wdAPIKWWRJ5V8QiQhKiZjpj4TkR7KT1fAF78Kf4eMXwy5tbXUkXyKpj0Izi1Z2
Oe2NHcGOMXbSBYSBK0N9sYXFWKhE3CRkEZ3yoYwTwoDYpDuMWffnRX1a0TGseUb3
xX9j+818/FyKhwEdL4rIHwOYW/iITLUOSUAOt2lnM2xWx3G1aNX7RjreOdobVm7Z
8ZVbX2zFBrP8Fe964ZutoG7FjBqurrOtoJUrZPEPWOcjDMPBi9JfRfwtLzglAnXh
IUglDUxMXscaQulEez3J
=ospe
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6/omap-hwmod-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/soc
ARM: OMAP2+: second set of hwmod changes for v4.6
These patches add RTC support for the AM43xx, and add support for
the DRA7xx eDMA controller's TPCC, TPTC0, and TPTC1 IP blocks.
Also included is a workaround for PRCM hardreset control of the DRA7xx
PCIe subsystem.
Note that I do not have a DRA7xx board, and therefore cannot
test any patches for that SoC family.
Basic build, boot, and PM test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-b-for-v4.6/20160301021258/
Add hwmod data for the eDMA blocks:
- TPCC: Third-party channel controller
- TPTC0: Third-party transfer controller 0
- TPTC1: Third-party transfer controller 1
The TPCC's clock gating status follows the status of its clock and
power domain. This means that the hwmod code can not directly control
the TPCC enable/disable status.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: rephrased last two sentences of the patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Linus Torvalds
Rafael J. Wysocki
Arnd Bergmann
Tony Lindgren
Viresh Kumar
Kevin Hilman
Roger Quadros
Dave Gerlach
Anna-Maria Gleixner
Nishanth Menon
Jonas Rabenstein
Suman Anna
Lokesh Vutla
Vignesh R
Peter Ujfalusi
Keerthy
Vishal Mahaveer
Olof Johansson