The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series removes the hardcoded register base address for mvebu.
For round 2:
- multiplatform
- fix booting on anything other than mvebu
Depends (none new for round 2):
- mvebu/fixes-non-critical (up to tags/fixes-non-3.11-1)
- mvebu/cleanup (up to tags/cleanup-3.11-3)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJRxICoAAoJEAi3KVZQDZAeOK8H/0k4YVpRqGlOvJ4iyeO0YTx/
n0Mz+piw6Ra5U+EiaAZ0sDNO9eceDj88mZza0xEm2bfYCy2Lr2UA0TDCG/3V2WPM
ye8Avr9PyCVAGgS9SuNH9oBIxFa5nVOsPje/qsZDEKsU9LrbjCXBudtRTyiH+E8K
rfLi822eXS1Ckh2rpYL0XxIho2630vduAZpCecaRvvjXFqWRBfoR3N9k2LOgJC3l
SSmBQs7H+C7QYh1iZwemMixh2W+Ck0qiGttfIrEYeKuWpo9+5hyLvvqLZVpjA67D
kyYnyJ/OPMP4W4DoATtiGgKsCTj3IMPiC/yMCgFMocl5gUXuLqf//d3g2Uc/3UY=
=SY7t
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu register map changes for v3.11 (round 2)
This series removes the hardcoded register base address for mvebu.
For round 2:
- multiplatform
- fix booting on anything other than mvebu
Depends (none new for round 2):
- mvebu/fixes-non-critical (up to tags/fixes-non-3.11-1)
- mvebu/cleanup (up to tags/cleanup-3.11-3)
* tag 'regmap-3.11-2' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: fix coherency_late_init() for multiplatform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As noticed by Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>, commit
865e0527d2 ('arm: mvebu: avoid hardcoded virtual address in
coherency code') added a postcore_initcall() to register the bus
notifier that the mvebu code needs to apply correct DMA operations on
its platform devices breaks the multiplatform boot on other platforms,
because the bus notifier registration is unconditional.
This commit fixes that by registering the bus notifier only if we have
the mvebu coherency unit described in the Device Tree. The conditional
used is exactly the same in which the bus_register_notifier() call was
originally enclosed before 865e0527d2 ('arm: mvebu: avoid hardcoded
virtual address in coherency code').
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This series removes the hardcoded register base address for mvebu.
Depends:
- mvebu/fixes-non-critical (up to tags/fixes-non-3.11-1)
- mvebu/cleanup (up to tags/cleanup-3.11-3)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJRujY/AAoJEAi3KVZQDZAeQ/8H/186TUo1jWJJP/Tdp6Rg09qK
FeZeVH9YrViLO2g2iO338TlfIjshJW8HgMv8tnuJo9xLz5wtws3Dpv5BpcYoGoKs
vU/d1EZC4vJTs5IZ2fS6p0LpvV8YrUYVi9v7uPWHFx6DYGznuHPP/q8Hu6Pa0Tok
MoPNAihBYMEhePGuBQo1j3xPtteifJy/CUv5iSrAAJSEI5zGRc7QO/0ItS2gc9qy
odFZKTZnGPlp/79np4I1/cjNTRuD5kf/9IzNFxl4ZL4X7Nre9J+8IFoPU671EDw1
XMBEtf6ThO6Z8oLiVPxeHlSLO2o7xQj7VEAUoSEsiK4whJAfxFiOqIiIC5SXfDA=
=hKzx
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
mvebu register map changes for v3.11
This series removes the hardcoded register base address for mvebu.
Depends:
- mvebu/fixes-non-critical (up to tags/fixes-non-3.11-1)
- mvebu/cleanup (up to tags/cleanup-3.11-3)
* tag 'regmap-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: disable DEBUG_LL/EARLY_PRINTK in defconfig
arm: mvebu: add another earlyprintk Kconfig option
arm: mvebu: don't hardcode the physical address for mvebu-mbus
arm: mvebu: don't hardcode a physical address in headsmp.S
arm: mvebu: remove hardcoded static I/O mapping
arm: mvebu: move cache and mvebu-mbus initialization later
arm: mvebu: avoid hardcoded virtual address in coherency code
arm: mvebu: remove dependency of SMP init on static I/O mapping
arm: mvebu: fix length of Ethernet registers area in .dtsi
arm: mvebu: fix length of SATA registers area in .dtsi
arm: mvebu: mark functions of armada-370-xp.c as static
ARM: mvebu: Remove init_irq declaration in machine description
ARM: Orion: Remove redundant init_dma_coherent_pool_size()
Signed-off-by: Olof Johansson <olof@lixom.net>
minimal support for am43x SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3bVH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Omap SoC changes. Mostly improves am33xx support, and adds
minimal support for am43x SoCs.
* tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: AM43x: SRAM base and size
ARM: OMAP2+: AM43x: GP or HS ?
ARM: OMAP2+: AM43x: early init
ARM: OMAP2+: AM43x: static mapping
ARM: OMAP2+: AM437x: SoC revision detection
ARM: OMAP2+: AM43x: soc_is support
ARM: OMAP2+: AM43x: kbuild
ARM: OMAP2+: AM43x: Kconfig
ARM: OMAP2+: separate out OMAP4 restart
ARM: AM33XX: clk: Add clock node for EHRPWM TBCLK
ARM: OMAP3: clock data: get rid of unused USB host clock aliases and dummies
ARM: OMAP2+: AM33xx: Add missing reset status info to GFX hwmod
+ Linux 3.10-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Since the mvebu-mbus driver doesn't yet have a DT binding (and this DT
binding may not necessarily be ready for 3.11), the physical address
of the mvebu-mbus registers are currently hardcoded. This doesn't play
well with the fact that the internal registers base address may be
different depending on the bootloader.
In order to have only one central place for the physical address of
the internal registers, we now use of_translate_address() to translate
the mvebu-mbus register offsets into the real physical address, by
using DT-based address translation. This will go away once the
mvebu-mbus driver gains a proper DT binding.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the coherency_init() function is called a bit earlier, we can
actually read the physical address of the coherency unit registers
from the Device Tree, and communicate that to the headsmp.S code,
which avoids hardcoding a physical address.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that we have removed the need of the static I/O mapping for early
initialization reasons, and fixed the registers area length that were
broken, we can get rid of the static I/O mapping. Only the earlyprintk
mapping needs to be set up, using the debug_ll_io_init() helper
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Current, the L2 cache and the mvebu-mbus drivers are initialized at
->init_early() time. However, at ->init_early() time, ioremap() only
works if a static I/O mapping has already been put in place. If it's
not the case, it tries to do a memory allocation with kmalloc() which
is not possible so early at this stage of the initialization.
Since we want to get rid of the static I/O mapping, we cannot
initialize the L2 cache driver and the mvebu-mbus driver so early. So,
we move their initialization to the ->init_time() level, which is
slightly later (so ioremap() works properly), but sufficiently early
to be before the call of the ->smp_prepare_cpus() hook, which creates
an address decoding window for the BootROM, which requires the
mvebu-mbus driver to be properly initialized.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the coherency_get_cpu_count() function no longer requires a
very early mapping of the coherency unit registers, we can avoid the
hardcoded virtual address in coherency.c. However, the coherency
features are still used quite early, so we need to do the of_iomap()
early enough, at the ->init_timer() level, so we have the call of
coherency_init() at this point.
Unfortunately, at ->init_timer() time, it is not possible to register
a bus notifier, so we add a separate coherency_late_init() function
that gets called as as postcore_initcall(), when bus notifiers are
available.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ->smp_init_cpus() function is called very early during boot, at a
point where dynamic I/O mappings are not yet possible. However, in the
Armada 370/XP implementation of this function, we have to get the
number of CPUs. We used to do that by accessing a hardware register,
which requires relying on a static I/O mapping set up by
->map_io(). Not only this requires hardcoding a virtual address, but
it also prevents us from removing the static I/O mapping.
So this commit changes the way used to get the number of CPUs: we now
use the Device Tree, which is a representation of the hardware, and
provides us the number of available CPUs. This is also more accurate,
because it potentially allows to boot the Linux kernel on only a
number of CPUs given by the Device Tree, instead of unconditionally on
all CPUs.
As a consequence, the coherency_get_cpu_count() function becomes no
longer used, so we remove it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- clk: mvebu
- reorganize by SoC to remove built up #ifdefs
- add clk flags per clock gate
Note: this branch only depends on mvebu/pcie in order to prevent managing a
tricky modify/remove file merge conflict. By rebasing on mvebu/pcie, we are
able to build the resolution into the patch series. The change is small, and
has been tested by the respective authors.
depends:
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRplb0AAoJEAi3KVZQDZAefTAH/1PMcXV+N/9HUgmx9XNpWg7Z
3ODWrA7Ewdvq9hfv9t+EH0FIdrZRA400p+AJuWSUuLzS7NzmCMTk/Pzad/W36ZY2
+8yJXVThSHqEQN/Vi1FtZGTKqRXZX/udVH5oNFV9jrUEFvLwuI/6/hCdkzlFKEol
9YJHNUyiul9P0jpcDXSSTFCpNXUPgQPuGTtIip0TKFmZOdA2QglgQAVkIwACZ+uX
PA7ewiFj1yfOhv8eh+nnb5kAsJEj1ynfMJywn7P/OC6ugAJtE9D0ZpzlYuj3lFEo
Z2snnzU7wVARfp1i6x3kNUyBiGHnJfxJC1KMePj87XP80BVzX1rmCoFY6x9nutg=
=jIi7
-----END PGP SIGNATURE-----
Merge tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu clock restructuring for v3.11
- clk: mvebu
- reorganize by SoC to remove built up #ifdefs
- add clk flags per clock gate
* tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux:
clk: mvebu: disintegrate obsolete file
ARM: mvebu: move DT boards to SoC-centric clock init
ARM: kirkwood: move DT boards to SoC-centric clock init
ARM: dove: move DT boards to SoC-centric clock init
clk: mvebu: add Armada XP SoC-centric clock init
clk: mvebu: add Armada 370 SoC-centric clock init
clk: mvebu: add Kirkwood SoC-centric clock init
clk: mvebu: add Dove SoC-centric clock init
clk: mvebu: add common clock functions for core clk and clk gating
clk: mvebu: introduce per-clock-gate flags
- mvebu pcie
- fix return value check in mvebu_pcie_probe()
depends
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpPzyAAoJEAi3KVZQDZAeuf0H/2FsmnLgvJh24z1B1HLuWm52
TYgoORahPsuoP7L2RZBU6n3++UuX4NGbVcagqRDe1Asou0oG0fu6oXbdn0d4avff
hoIuRq3LWhQ6DYaeV34vV8vM8x79HYM7FT92zX7VZKJ6TL6KGSHHSvVKhqWo7y65
++Ogtl5hzjyMzcQo5LoDQ+bqVLZpbfF7D/dreCCzzmlODqCNZGoBeZOwTqyR9kDW
aO65yDcsFIky2YAGz+uT0ItNpAtGzshJU/d6QTHNlvKeae2NjMqv2X7hP4161uQ4
NGyCsm7Aif5WnBQGQsvgCIPnuxTaYaGOSZQLMG7pN7TJQgx0sgF93HmX/gUI/WQ=
=ye72
-----END PGP SIGNATURE-----
Merge tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
PCI-e driver for mvebu.
* tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux:
pci: mvebu: fix return value check in mvebu_pcie_probe()
arm: mvebu: PCIe support is now available on mvebu
pci: PCIe driver for Marvell Armada 370/XP systems
clk: mvebu: add more PCIe clocks for Armada XP
clk: mvebu: create parent-child relation for PCIe clocks on Armada 370
of/pci: Add of_pci_parse_bus_range() function
of/pci: Add of_pci_get_devfn() function
of/pci: Provide support for parsing PCI DT ranges property
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC centric clock init for Armada 370/XP can be used by calling of_clk_init.
Use it and get rid of mvebu_clocks_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When adding CPU to the SMP group and enabling the coherency on this
CPU we must protect the register access.
The previous implementation claims to be atomic but doesn't provide
any protection against parallel access to the coherency fabric control
and configuration registers.
This patch fixes this by using the ldrex and strex mechanism.
This method should be used in all accesses to those registers.
[gregory.clement@free-electrons.com: fixed the commit's topic]
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
All the functions in armada-370-xp.c are called from the
DT_MACHINE_START function pointers, so there is no need for them to be
visible outside of this file, and we therefore mark them as static.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the PCIe driver for mvebu has been integrated and all its
relevant dependencies, we can mark the ARCH_MVEBU platform has
MIGHT_HAVE_PCI, which allows to select the PCI bus support if needed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit ebafed7a ("ARM: irq: Call irqchip_init if no init_irq function is
specified") removed the need to explictly setup the init_irq field in
the machine description when using only irqchip_init. Remove that
declaration for mvebu as well.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Initially ARCH_REQUIRE_GPIOLIB was part of Thomas Petazzoni series
when he introduced the gpiolib support for mvebu:
93a59cf arm: mvebu: use GPIO support now that a driver is available
This commit was written to be applied for the ARCH_MVEBU which was
located in arch/arm/KConfig and was merged in 3.7.
In the same time Rob Herring moved the ARCH_MVEBU block to
arch/arm/mach-mvebu/Kconfig with this commit and also merged in 3.7:
387798b ARM: initial multiplatform support
Unfortunately the ARCH_REQUIRE_GPIOLIB have been lost during this
migration. This was not noticed until the v3.10-rc1, because mvebu as
part of ARCH_MULTIPLATFORM was always selected with ARCH_VEXPRESS, and
this architect selected ARCH_REQUIRE_GPIOLIB.
Since the following commit from Arnd: "883a106 ARM: default machine
descriptor for multiplatform", ARCH_VEXPRESS was then no more selected
by default with ARCH_MVEBU and it made appeared the lack of
ARCH_REQUIRE_GPIOLIB for mvebu. This commit added back the selection
of ARCH_REQUIRE_GPIOLIB for ARCH_MVEBU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch:
387870f mm: dmapool: use provided gfp flags for all dma_alloc_coherent() calls
makes these calls on Kirkwood and Orion5x redundant. The drivers are
not making atomic requests for coherent memory and hence the default
pool size is now sufficient.
Jason Cooper added mach-mvebu/ hunk, and corrected minor typos in commit
message.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch:
387870f mm: dmapool: use provided gfp flags for all dma_alloc_coherent() calls
makes these calls on Kirkwood and Orion5x redundant. The drivers are
not making atomic requests for coherent memory and hence the default
pool size is now sufficient.
Jason Cooper added mach-mvebu/ hunk, and corrected minor typos in commit
message.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
This is the third and smallest of the SoC specific updates.
Changes include:
* SMP support for the Xilinx zynq platform
* Smaller imx changes
* LPAE support for mvebu
* Moving the orion5x, kirkwood, dove and mvebu platforms
to a common "mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus"
driver. Since this is used on multiple platforms may potentially
get shared with other architectures (powerpc and arm64), it
was moved to drivers/bus/. We expect other similar drivers to
get moved to the same place in order to avoid creating more
top-level directories under drivers/ or cluttering up the
messy drivers/misc/ even more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rQsu
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
"This is the third and smallest of the SoC specific updates. Changes
include:
- SMP support for the Xilinx zynq platform
- Smaller imx changes
- LPAE support for mvebu
- Moving the orion5x, kirkwood, dove and mvebu platforms to a common
"mbus" driver for their internal devices.
It would be good to get feedback on the location of the "mbus" driver.
Since this is used on multiple platforms may potentially get shared
with other architectures (powerpc and arm64), it was moved to
drivers/bus/. We expect other similar drivers to get moved to the
same place in order to avoid creating more top-level directories under
drivers/ or cluttering up the messy drivers/misc/ even more."
* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: imx: reset_controller may be disabled
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
ARM i.MX53: make tve_ext_sel propagate rate change to PLL
ARM i.MX53: Remove unused tve_gate clkdev entry
ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
ARM: i.MX5: Add PATA and SRTC clocks
ARM: imx: do not bring up unavailable cores
ARM: imx: add initial imx6dl support
ARM: imx1: mm: add call to mxc_device_init
ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
...
- use the mvebu-mbus driver
- prep for LPAE support
Depends:
- mvebu/cleanup (tags/cleanup_for_v3.10)
- mvebu/drivers (tags/drivers_for_v3.10)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRbApqAAoJEAi3KVZQDZAeiUkH+gI3KNnIEmwbMANGy+zdX70Y
mVj5X51MkXCawqNPLT6KYTO16Ap8STBXDxLfQfll1BuIeATgQgqs8dCcykiYQ4me
45Hj9+6uZhfPpN43u4syFPoYaLSAMT9Oe/9ntcpdnyu4fEsRmGGh2Dg8bhYcG1B2
+IVB67qSJ3vU0D2bcqsbSPuSu9MW2Qloc5+SMR74TcsyseZw10kbvL6cdwi9DpNt
ru2c/bXqO88U1pmeedJ8Cxl0KGFDhocYWV6orqph+2jIxuCDYd7DjOXFKeMHwcDX
lj54wMUyp8EzTs+huhnK3qL6waXTyccmMDDvgIL6WiFywvklTOJOFz0BnfHIHpk=
=RK7u
-----END PGP SIGNATURE-----
Merge tag 'soc_for_v3.10' of git://git.infradead.org/users/jcooper/linux into next/soc2
From Jason Cooper:
mvebu soc changes for v3.10
- use the mvebu-mbus driver
- prep for LPAE support
Depends:
- mvebu/cleanup (tags/cleanup_for_v3.10)
- mvebu/drivers (tags/drivers_for_v3.10)
* tag 'soc_for_v3.10' of git://git.infradead.org/users/jcooper/linux:
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
bus: mvebu: fix mistake in PCIe window target attribute for Kirkwood
bus: mvebu-mbus: Restore checking for coherency fabric hardware
ARM: Orion: add dbg_show function to gpio-orion driver
bus: introduce an Marvell EBU MBus driver
arm: mach-orion5x: use mv_mbus_dram_info() in PCI code
arm: plat-orion: use mv_mbus_dram_info() in PCIe code
arm: plat-orion: only build addr-map.c when needed
Signed-off-by: Olof Johansson <olof@lixom.net>
When the Marvell Armada 370/XP support was included in the kernel, the
drivers/irqchip/ directory didn't exist and the minimal infrastructure
in it also didn't exist. Now that we have those things in place, we
move the Armada 370/XP IRQ controller driver from
arch/arm/mach-mvebu/irq-armada-370-xp.c to
drivers/irqchip/irq-armada-370-xp.c.
Note in order to reduce code movement and therefore ease the review of
this patch, we intentionally introduce a forward declaration of
armada_370_xp_handle_irq(). It is in fact not needed because this
handler can now simply be implemented before
armada_370_xp_mpic_of_init(). That will be done in the next commit.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In preparation for moving the IRQ controller driver to
drivers/irqchip/, we don't want the IRQ controller driver to be
responsible for initializing the L2 cache. Instead, let's initialize
the L2 cache at the init_early() level, like mach-exynos/common.c is
doing.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to be able to support the LPAE, the internal registers
virtual base must be aligned to 2MB. In LPAE section size is 2MB, in
earlyprintk we map the internal registers and it must be section
aligned.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When LPAE is activated on Armada XP, all registers and IOs are still
32bit, the 40bit extension is on the CPU to DRAM path (windows) only.
That means that all the DMA transfer are restricted to the low 32 bits
address space. This is limitation is achieved by selecting ZONE_DMA.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The changes needed to migrate the mach-mvebu (Armada 370 and Armada
XP) to the mvebu-mbus driver are fairly minimal, since not many
devices currently supported on those SoCs use address decoding
windows. The only one being the BootROM window, used to bring up
secondary CPUs.
However, this BootROM window needed for SMP brings an important
requirement: the mvebu-mbus driver must be initialized at the
->early_init() time, otherwise the BootROM window cannot be setup
early enough to be ready before the secondary CPUs are started.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch fix the regression introduced by the commit 3202bf0157
"arm: mvebu: Improve the SMP support of the interrupt controller":
GPIO IRQ were no longer delivered to the CPUs.
To be delivered to a CPU an interrupt must be enabled at CPU level and
at interrupt source level. Before the offending patch, all the
interrupts were enabled at source level during map() function. Mask()
and unmask() was done by handling the per-CPU part. It was fine when
running in UP with only one CPU.
The offending patch added support for SMP, in this case mask() and
unmask() was done by handling the interrupt source level part. The
per-CPU level part was handled by the affinity API to select the CPU
which will receive the interrupt. (Due to some hardware limitation
only one CPU at a time can received a given interrupt).
For "normal" interrupt __setup_irq() was called when an irq was
registered. irq_set_affinity() is called from this function, which
enabled the interrupt on one of the CPUs. Whereas for GPIO IRQ which
were chained interrupts, the irq_set_affinity() was never called and
none of the CPUs was selected to receive the interrupt.
With this patch all the interrupt are enable on the current CPU during
map() function. Enabling the interrupts on a CPU doesn't depend
anymore on irq_set_affinity() and then the chained irq are not anymore
a special case. However the CPU which will receive the irq can still
be modify later using irq_set_affinity().
Tested with Mirabox (A370) and Openblocks AX3 (AXP), rootfs mounted
over NFS, compiled with CONFIG_SMP=y/N.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: Ryan Press <ryan@presslab.us>
Investigated-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The commit 3a6f08a37 "arm: mvebu: Add support for local interrupt",
managed the 28th first interrupts as local interrupt to match the
hardware specification. Among these interrupts there are the Gigabits
Ethernet ones used by the mvneta driver. Unfortunately the state of
the percpu_irq API prevents the driver to use it.
Indeed the interrupts have to be freed when the .stop() function is
called. As the free_percpu_irq() function don't disable the interrupt
line, we have to do it on each CPU before calling this. The function
disable_percpu_irq() only disable the percpu on the current CPU and
there is no function which allows to disable a percpu irq on a given
CPU. Waiting for the extension of the percpu_irq API, this fix allows
to use again the mvneta driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
* More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers here,
ethernet and PCI still remain.
* SMP support for mvebu is improved with support for the
local interrupt controller.
* The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the patches
in his tree that all of the patches in this branch are based on, which
caused merge conflicts between the new and old versions of those patches.
To work around the merge conflicts, this branch rebases all patches
on top of the respective MMC patches that did get merged into 3.9.
The patches are all identical to the versions that were part of
linux-next, but have a new commit date.
Merge conflicts:
* in board-nsa310.c, the gpio.h inclusion was removed prematurely and
put back as a bug fix earlier. With this series it is really not needed
any more.
* The patch to add rtc support was already applied by Andrew Morton,
and conflicts with a second copy that was in this series, which adds
a lot of other devices to arch/arm/boot/dts/armada-370-xp.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7l0+
-----END PGP SIGNATURE-----
Merge tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC mvebu platform changes from Olof Johansson:
"This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
- More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers
here, ethernet and PCI still remain.
- SMP support for mvebu is improved with support for the local
interrupt controller.
- The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the
patches in his tree that all of the patches in this branch are based
on, which caused merge conflicts between the new and old versions of
those patches.
To work around the merge conflicts, this branch rebases all patches on
top of the respective MMC patches that did get merged into 3.9. The
patches are all identical to the versions that were part of
linux-next, but have a new commit date."
* tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits)
arm: mvebu: enable the SD card slot on Armada 370 Reference Design board
ARM: kirkwood: topkick: init mvsdio via DT
ARM: kirkwood: nsa310: convert to pinctrl
ARM: Kirkwood: topkick: Enable i2c bus.
ARM: kirkwood: topkick: convert to pinctrl
ARM: dove: convert serial DT nodes to clocks property
arm: mvebu: Add SPI flash on Armada 370 DB board
arm: mvebu: Add SPI flash on Armada XP-DB board
arm: mvebu: Add SPI flash on Armada XP-GP board
arm: mvebu: Add support for SPI controller in Armada 370/XP
clocksource: update and move armada-370-xp-timer documentation to timer directory
arm: mvebu: update DT to support local timers
ARM: Dove: convert usb host controller to DT
arm: mvebu: Enable USB controllers on Armada 370/XP boards
arm: mvebu: Add support for USB host controllers in Armada 370/XP
arm: mvebu: add button for OpenBlocks AX3-4
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
ARM: Kirkwood: Convert NSA310 I2C to device tree
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
ARM: Kirkwood: Convert NSA310 to DT based regulators.
...
MPIC allows the use of private interrupt for each CPUs. The 28th first
interrupts are per-cpu. This patch adds support to use them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch makes the interrupt controller driver more SMP aware for
the Armada XP SoCs. It adds the support for the per-CPU irq. It also
adds the implementation for the set_affinity hook.
Patch initialy wrote by Yehuda Yitschak and reworked by Gregory
CLEMENT.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
Selecting only CONFIG_ARCH_MVEBU but not the respective
options for Armada 370 or Armada XP results in these
link errors:
arch/arm/mach-mvebu/built-in.o: In function `armada_xp_smp_init_cpus':
arch/arm/mach-mvebu/platsmp.c:91: undefined reference to `coherency_get_cpu_count'
arch/arm/mach-mvebu/platsmp.c:104: undefined reference to `armada_mpic_send_doorbell'
arch/arm/mach-mvebu/built-in.o: In function `armada_xp_smp_prepare_cpus':
arch/arm/mach-mvebu/platsmp.c:111: undefined reference to `set_cpu_coherent'
arch/arm/mach-mvebu/built-in.o: In function `armada_xp_boot_secondary':
arch/arm/mach-mvebu/platsmp.c:83: undefined reference to `armada_xp_boot_cpu'
arch/arm/mach-mvebu/built-in.o: In function `armada_xp_secondary_init':
arch/arm/mach-mvebu/platsmp.c:75: undefined reference to `armada_xp_mpic_smp_cpu_init'
arch/arm/mach-mvebu/built-in.o: In function `armada_xp_secondary_startup':
arch/arm/mach-mvebu/headsmp.S:46: undefined reference to `ll_set_cpu_coherent'
We can solve this by enabling all common MVEBU files that are
referenced by the SMP files. This means we enable code that
is not going to be used without a machine descriptor referencing
it, but only if the kernel is configured specifically for this
case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Some systems compile in both ARMv6 and ARMv7 into multiplatform
configurations. This means the default compiler flags are for ARMv6,
and we will get:
arch/arm/mach-mvebu/coherency_ll.S: Assembler messages:
arch/arm/mach-mvebu/coherency_ll.S:45: Error: selected processor does not support `dsb'
Fix this by specifying ARMv7 flags for coherency_ll.o.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The armada_cfg_base() function returns the base address of the
registers that allow to configure the decoding for a particular
address window. On Armada 370/XP, the lower windows have more
configuration registers (4 registers) than the higher windows (2
registers). This armada_cfg_base() takes this into account by doing a
different offset calculation depending on the window number, but this
offset calculation was wrong for the higher windows.
Even though we were not using high window numbers until now (only
window 0 is used to map the BootROM, needed for SMP), we use this
function at boot time to disable all windows to ensure that nothing
remains intialized from what the bootloader has done.
Unfortunately, the U-Boot on the OpenBlocks AX3-4 uses a window with a
high number (above 8) to remap the BootROM. And then when the kernel
boots, it remaps the BootROM in window 0. Normally, this is not a
problem, because all windows have previously been disabled. Except
that due to our wrong offset calculation, the windows with high
numbers were not properly disabled, leading to the BootROM being
mapped twice. The visible result of this bug was that the kernel was
unable to get the second CPU started on the OpenBlocks AX3-4
platform. With this fix, all windows are properly cleared at boot
time, the BootROM is remapped only once in window 0, and the second
CPU boots fine.
Thanks a lot to Lior Amsamlen <alior@marvell.com> for his help in
debugging this problem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
Strictly speaking, this bug was introduced in 3.7, but since the only
platforms supported in 3.7 were Armada 370 and Armada XP, and there
was anyway no SMP support at this time, it isn't really worth the
effort to push this patch in 3.7.
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs+5oACgkQCwYYjhRyO9UywACfVp3WPDHLxE8ypew3AWoTyxe3
JcMAoIjojnjWCd44cqDJ4uEpvi6KNquE
=BR8m
-----END PGP SIGNATURE-----
Merge tag 'marvell-armadaxp-smp-for-3.8' of github.com:MISL-EBU-System-SW/mainline-public into mevbu-dt-additions
SMP support for Armada XP
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
Conflicts:
arch/arm/mach-mvebu/armada-370-xp.c
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs/LcACgkQCwYYjhRyO9WrOgCfeWpA9XdQnwexySw5tPXS7Qdp
aJEAn2ql07SECpTRWezTJptHL0oI1dFF
=b0T7
-----END PGP SIGNATURE-----
Merge tag 'marvell-hwiocc-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
Add hardware I/O coherency support for Armada 370/XP
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
Paul Gortmaker
Robin Holt
Arnd Bergmann
Thomas Petazzoni
Olof Johansson
Jason Cooper
Sebastian Hesselbarth
Nadav Haklai
Maxime Ripard
Gregory CLEMENT
Andrew Lunn
Linus Torvalds
Lior Amsalem
Marek Belisko
Tony Lindgren
Stephen Warren