Chips with 16-bit registers don't usually work well with I2C block
commands. For example, neither the LM75 datasheet nor the TMP102 datasheet
mentions block command support, and in fact it does not work for any of
those chips. Also, it is not clear how the block command would handle
16-bit SMBus operations in the fist place, since the data format associated
with those commands is either little endian or big endian, which requires
some kind of conversion to or from host byte order.
Only use i2c block commands if both register and value width is 8 bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows to read/write up to 32 bytes of data and is to be prefered
if supported before the register read/write smbus support.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Init functions defined in regmap*.c files are now prefixed with
__, take lockdep key and class parameters, and should not be
called directly: move the documentation to regmap.h, where the
macros are defined.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lockdep validator complains about recursive locking and deadlock
when two different regmap instances are called in a nested order.
That happens anytime a regmap read/write call needs to access
another regmap.
This is because, for performance reason, lockdep groups all locks
initialized by the same mutex_init() in the same lock class.
Therefore all regmap mutexes are in the same lock class, leading
to lockdep "nested locking" warnings if a regmap accesses another
regmap.
In general, it is impossible to establish in advance the hierarchy
of regmaps, so we make sure that each regmap init call initializes
its own static lock_class_key. This is done by wrapping all
regmap_init calls into macros.
This also allows us to give meaningful names to the lock_class_key.
For example, in rt5677 case, we have in /proc/lockdep_chains:
irq_context: 0
[ffffffc0018d2198] &dev->mutex
[ffffffc0018d2198] &dev->mutex
[ffffffc001bd7f60] rt5677:5104:(&rt5677_regmap)->_lock
[ffffffc001bd7f58] rt5677:5096:(&rt5677_regmap_physical)->_lock
[ffffffc001b95448] &(&base->lock)->rlock
The above would have resulted in a lockdep recursive warning
previously. This is not the case anymore as the lockdep validator
now clearly identifies the 2 regmaps as separate.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SMBus access functions assume that 16-bit values are formatted as
little endian numbers. The direct i2c access functions in regmap,
however, assume that 16-bit values are formatted as big endian numbers.
As a result, the current code returns different values if an i2c chip's
16-bit registers are accessed through i2c access functions vs. SMBus
access functions.
Use regmap_smbus_read_word_swapped and regmap_smbus_write_word_swapped
for 16-bit SMBus accesses if a chip is configured as REGMAP_ENDIAN_BIG.
If the chip is configured as REGMAP_ENDIAN_LITTLE, keep using
regmap_smbus_write_word_data and regmap_smbus_read_word_data. Otherwise
reject registration if the controller does not support direct i2c accesses.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
For many drivers which will support rich endianness of Devices
need define DT properties by itself with the binding support.
The endianness using regmap:
Index Device Properties if needs bytes-swap,
or just ignore it
-------------------------------------------------------------
1 BE 'big-endian'
2 LE 'little-endian'
The properties include all the register values and the buffers.
And these properties are very usful for the MMIO devices:
Such as: a memory-mapped device, on one SoC is in BE mode, while
in another SoC will be in LE mode, and the CPU will always in LE
mode.
For the first case, we must use cpu_to_be32/be32_to_cpu for
32-bit registers accessing, so the 'big-endian' property is needed.
For the second case, we can just ignore the bytes-swap
functions like cpu_to_le32/le32_to_cpu, so the 'little-endian'
property could be abscent.
And vice versa...
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some I2C adapters are only compatible with the SMBus protocol and do not
support standard I2C transfers.
Fallback to SMBus transfers if we encounter such kind of adapters.
The transfer type is chosen according to the val_bits field in the regmap
config.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The only context needed by I2C and SPI bus definitions is the device
itself; this can be converted to an i2c_client or spi_device in order
to perform IO on the device. However, other bus types may need more
context in order to perform IO. Enable this by having regmap_init accept
a bus_context parameter, and pass this to all bus callbacks. The
existing callbacks simply pass the struct device here. Future bus types
may pass something else.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Save error handling and unwinding code in drivers by providing managed
versions of the regmap init functions, simplifying usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No longer used as users link directly with the bus types so the core
module infrastructure does refcounting for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_REGMAP_I2C/SPI are set to m when selected by a tristate config
option that's set to m. The regmap modules don't specify a license, so
fail to link to regmap_init at load time, since that is EXPORT_SYMBOL_GPL.
Fix this by specifying a license for the regmap modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Guenter Roeck
Mark Brown
Markus Pargmann
Nicolas Boichat
Xiubo Li
Boris BREZILLON
Paul Gortmaker
Mark Brown
Stephen Warren