LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2975 is mostly compatible to LTC2974, but supports input current
and power measurement.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm attributes have well defined names, which should be used.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add an item to the checklist when submitting a new hwmon driver: only
some I2C addresses can be probed, others should not for safety
reasons.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add hwmon driver for the Microchip TC74.
The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C address 0x37 may be used by EEPROMs, which can result in false
positives. Do not attempt to detect a chip at this address.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8620E is mostly compatible to IT7828F. Add generic support for it.
IT8620E supports up to 6 fan tachometers and 6 pwm controls.
Support for the 6th tachometer and for the additional pwm controls
are addded in separate patches.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8790E is a super-IO chip with three fan tachometers. It is mostly
compatible to IT8728F, but only supports three fan tachometers
instead of five.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest
that the upper 8 bit of the device ID reflect the chip ID and the lower
8 bit reflect the version number, modify the code to accept all chips
with ID 0x29xx.
Also add support for TS3001 and TSE2004.
Some of the datasheets for older chips are no longer available from
the IDT web site, so replace explicit links in the documentation with
a generic note.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8781F is mostly compatible to IT8782F. Major difference is that it only
supports four instead of six UART channels, and therefore does not share
the uart6 pins.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This attribute allows to configure the update interval of ina226. Although
the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can
now modify said interval by changing the averaging rate.
While we're at it - add an additional variable to ina2xx_data, which holds
the current configuration settings - this way we'll be able to restore the
configuration in case of an unexpected chip reset.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt resistance can only be set via platform_data or device tree. This
isn't suitable for devices in which the shunt resistance can change/isn't
known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP435 supports a range of I2C addresses, not just 0x4c.
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95233 is similar to LM95234, but it only supports two
instead of four external temperature sensors.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95235 is register compatible to LM95245.
Also update link to LM95245 data sheet, and drop the link to the
datasheet from the driver source to simplify code maintenance.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6792D is similar to NCT6791D. Only beep control and temperature
monitoring registers are different.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document support for NCT6102D/NCT6104D/NCT6106D and NCT6791D.
Document that NCT5573D is compatible to NCT6775F with the same chip ID.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is basically a faster lm75 with improved (11 bit) resolution.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds temperature monitoring support for F15h M60h processor.
- Add new pci device id for the relevant processor
- The functionality of REG_REPORTED_TEMPERATURE is moved to
D0F0xBC_xD820_0CA4 [Reported Temperature Control]
- So, use this to get CUR_TEMP value
- Since we need an indirect register access, protect this with
a mutex lock
- Add Kconfig, Doc entries to indicate support for this processor.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
[Guenter Roeck: Declare new mutex and function static]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver enables control of fans connected to PWM lines.
This driver uses the PWM framework, so it is compatible with all
PWM devices that provide drivers through the PWM framework.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
[Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For TI power management chip TPS40422, READ_TEMPERATURE_2 command is supported on
page 1 of the chip, but the original driver(pmbus.c) only tried to detect this command
on page 0, this will lead to a result that the temperature sensor in page 1 couldn't
be detected. This change is to isolate the tps40422 driver from pmbus.c into a solo
front-end driver.
Signed-off-by: Zhu Laiwen <richard.zhu@nsn.com>
[Guenter Roeck: Dropped unnecessary license text (fixes checkpatch warning)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Not all supported chips support the entire I2C address range.
Only accept specific chips at the addresses supported by that chip.
Check for invalid values in conversion rate and status registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
This patch adds support for the ntc thermistor B57330V2103 from EPCOS.
Signed-off-by: Johannes Pointner <johannes.pointner@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for Lattice's POWR1220 power manager IC. Read
access to all the ADCs on the chip are supported through the hwmon
sysfs files.
Signed-off-by: Scott Kanowitz <skanowitz@echo360.com>
[Guenter Roeck: Removed some extra ( )]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Murata Manufacturing Co., Ltd is the vendor for
NTC (Negative Temperature coefficient) based Thermistors.
But, the driver extensively uses "NTC" as the vendor name.
This patch corrects the vendor name also updates the
compatibility strings according to the vendor-prefix.txt
Note: Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Sensirion SHTC1 and compatible temperature and humidity
sensors.
Signed-off-by: Tomas Pop <tomas.pop@sensirion.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New chip support to existing drivers:
Add support for STTS2004 and AT30TSE004 to jc42 driver
Add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
Document hwmon kernel API
Convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421,
and tmp102 drivers to use new hwmon API functions
Replace function macros in lm80, lm92, and jc42 drivers with
real code
Convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
Various additional cleanup and minor bug fixes in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dytt
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging into next
Pull hwmon updates from Guenter Roeck:
"New driver for NCT6683D
New chip support to existing drivers:
- add support for STTS2004 and AT30TSE004 to jc42 driver
- add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
- document hwmon kernel API
- convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421, and
tmp102 drivers to use new hwmon API functions
- replace function macros in lm80, lm92, and jc42 drivers with real
code
- convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
- various additional cleanup and minor bug fixes in several drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (60 commits)
hwmon: (nct6775) Fix probe unwind paths to properly unregister platform devices
hwmon: (nct6683) Fix probe unwind paths to properly unregister platform devices
hwmon: (ultra45_env) Introduce managed version of kzalloc
hwmon: Driver for NCT6683D
hwmon: (lm80) Rearrange code to avoid forward declarations
hwmon: (lm80) Convert fan display function macros into functions
hwmon: (lm80) Convert voltage display function macros into functions
hwmon: (lm80) Convert temperature display function macros into functions
hwmon: (lm80) Normalize all temperature values to 16 bit
hwmon: (lm80) Simplify TEMP_FROM_REG
hwmon: (lm83) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm83) Rearange code to avoid forward declarations
hwmon: (lm83) Drop FSF address
hwmon: (max1619) Convert to use devm_hwmon_device_register_with_groups
hwmon: (max1619) Drop function macros
hwmon: (max1619) Rearrange code to avoid forward declarations
hwmon: (max1619) Drop FSF address
hwmon: (max1619) Fix critical alarm display
hwmon: (jc42) Add support for STTS2004 and AT30TSE004
hwmon: (jc42) Convert function macros into functions
...
The temp[1-*]_min_hyst sysfs attribute is already implemented by 3
hwmon drivers (adt7x10, lm77 and lm92) but was missing from the
standard interface.
Also add temp[1-*]_lcrit_hyst for consistency, even though no driver
implement that one for the time being.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Also fix links to datasheets for other supported sensors from
ST Microelectronics, and add links to several Atmel datasheets.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips in this chip series only support a single hysteresis value. Having
multiple writable hysteresis attributes is therefore confusing, since a single
write affects all hysteresis temperatures. Make all but one (temp1_crit_hyst)
read-only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With the driver now supporting several chip variants,
it is about time to document what is supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon subsystem has been around for a while. Time to document
its kernel API.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Updating the hysteresis value when updating the critical temperature limit
was following the rule of 'least surprise'. However, it had the undesirable
side effect of changing the hysteresis for all other attributes, which
defeats the purpose of least surprise. In addition, it could result in
invalid hysteresis values if the resulting hysteresis was too large. In such
cases the resulting hysteresis ended up changed anyway, which again defeats
the purpose. So drop that code and document the new behavior.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Jean Delvare:
"This includes a number of driver conversions to
devm_hwmon_device_register_with_groups, a few cleanups, and
support for the ITE IT8623E"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Add support for IT8623E
hwmon: (it87) Fix IT8603E define name
hwmon: (lm90) Convert to use hwmon_device_register_with_groups
hwmon: (lm90) Create all sysfs groups in one call
hwmon: (lm90) Always use the dev variable in the probe function
hwmon: (lm90) Create most optional attributes with sysfs_create_group
hwmon: Avoid initializing the same field twice
hwmon: (pc87360) Avoid initializing the same field twice
hwmon: (lm80) Convert to use devm_hwmon_device_register_with_groups
hwmon: (adm1021) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Avoid initializing the same field twice
hwmon: (lm63) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Create all sysfs groups in one call
hwmon: (lm63) Introduce 'dev' variable to point to client->dev
hwmon: (lm63) Add additional sysfs group for temp2_type attribute
hwmon: (f71805f) Fix author's address
Add support for the IT8623E found on Asus motherboards. It has same
hardware monitoring block as IT8603E.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Adding new PCI ID to support AMD F16 M30h processor (Mullins).
While at it, modify Kconfig and Doc files to reflect the
support for newer processors
Note: PCI ID for this processor will make it into pci_ids.h
as part of this patch:
http://marc.info/?l=linux-kernel&m=139291362126057&w=2
which should be pulled into 3.15 when merge window opens
(It currently sits in 'for-next' branch of bp.git-
https://git.kernel.org/cgit/linux/kernel/git/bp/bp.git/log/?h=for-next)
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip's programming interface is quite similar to LTC3880
and supports the same set of sensors.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hysteresis register is shared among both temperature sensors.
This means changing one also affects the other. To avoid confusion,
established way to express this is to make only the first instance writable
and keep all other instances as read-only. Otherwise users may be
confused that changing the second writable value also affects the first,
while it is more obvious that a writable value may affect a different
read-only value.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
ADC128D818 is a System Monitor with Temperature Sensor. It is similar to LM80
and LM96080, but has 16 bit wide sensor registers and no fan speed monitoring.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC4260 is a Positive Voltage Hot Swap Controller.
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for IT8603E.
This closes bug #57861:
https://bugzilla.kernel.org/show_bug.cgi?id=57861
[JD: Fixes and clean-ups.]
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
TI TMP451 is mostly compatible with ADT7461, except for
local temperature low byte and max conversion rate.
Add support to the LM90 driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull hwmon fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (emc6w201) Do not declare enum variable
hwmon: (w83792d) Update module author
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
w83792d was written by me in 2004, I'd like to update my first name
into my current one to keep consistent, and delete invalid address.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The temperature reporting interface stays the same, so we just
add the PCI-ID to the list.
Verified on AMD Olive Hill.
Signed-off-by: Wei Hu <wei@aristanetworks.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Corrected the word adventerous to adventurous.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for ads1115 device to ads1015 driver.
Based on work of Emiliano Carnati <carnatiatebneuro.com>.
Tested on ARM CPU based board.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for DS1631, DS1721, and DS1731 to ds1621 driver
Remove detect function from ds1621 driver as unreliable
Bug fixes in nct6775, iio_hwmon, and adm1021 drivers
Remove redundant platform_set_drvdata in various drivers
Add device tree support to ina2xx driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OdGw
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver to support GMT G762/G763 pwm fan controllers
- add support for DS1631, DS1721, and DS1731 to ds1621 driver
- remove detect function from ds1621 driver as unreliable
- bug fixes in nct6775, iio_hwmon, and adm1021 drivers
- remove redundant platform_set_drvdata in various drivers
- add device tree support to ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Fix temperature rounding operations
hwmon: (nct6775) Drop unsupported fan alarm attributes for NCT6775
hwmon: (nct6775) Fix temperature alarm attributes
Add support for GMT G762/G763 PWM fan controllers
hwmon: (ina2xx) Add device tree support to pass the shunt resistor
hwmon: (ds1621) Update documentation
hwmon: (ds1621) Add DS1731 chip support to ds1621 driver
hwmon: (iio_hwmon) add alias table
hwmon: (adm1021) Do not create min sysfs attributes for LM84
hwmon: (ds1621) Remove detect function
hwmon: (ds1621) Add ds1631 chip support to ds1621 driver and documentation
hwmon: (ds1621) Add ds1721 update interval sysfs attribute
hwmon: (ds1621) Add ds1721 chip support
hwmon: (w83627ehf) Remove redundant platform_set_drvdata()
hwmon: (ntc_thermistor) Remove redundant platform_set_drvdata()
hwmon: (i5k_amb) Remove redundant platform_set_drvdata()
hwmon: (coretemp) Remove redundant platform_set_drvdata()
hwmon: (abituguru3) Remove redundant platform_set_drvdata()
GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another way that is device tree to pass the shunt resistor
value to driver except for platform data.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[Guenter Roeck: Added missing of.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace some written information with tables to improve readability
and to simplify adding newer devices in the future.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These changes add DS1731 chip support to the ds1621 driver,
Kconfig, and documentation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Due to a lack of device and vendor identification registers, the
Dallas/Maxim DS16xx devices cannot be uniquely detected, sometimes
resulting in false positives. Therefore, the detect function is
being removed in favor of explicit device instantiation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add definitions, information, and code for ds1631 chip support
to the ds1621 driver.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ds1721 device can be configured for 9..12 bit resolutions;
add a sysfs attribute for userspace to configure this attribute.
The definition, description, details, and usage are shown in the
documentation and were crafted from an LM73 driver patch done by
Chris Verges & Guenter Roeck).
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the ds1621 documentation, driver, and Kconfig with
ds1721 chip support.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Basically it's the same as the original DS75 but much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Most LM75-compatible chips can either sample much faster or with a
much better resolution than the original LM75 chip. So far the lm75
driver did not let the user take benefit of these improvements. Do it
now.
I decided to almost always configure the chip to use the best
resolution possible, which also means the longest sample time. The
only chips for which I didn't are the DS75, DS1775 and STDS75, because
they are really too slow in 12-bit mode (1.2 to 1.5 second worst case)
so I went for 11-bit mode as a more reasonable tradeoff. This choice is
dictated by the fact that the hwmon subsystem is meant for system
monitoring, it has never been supposed to be ultra-fast, and as a
matter of fact we do cache the sampled values in almost all drivers.
If anyone isn't pleased with these default settings, they can always
introduce a platform data structure or DT support for the lm75. That
being said, it seems nobody ever complained that the driver wouldn't
refresh the value faster than every 1.5 second, and the change made
it faster for all chips even in 12-bit mode, so I don't expect any
complaint.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
- OpenFirmware/DeviceTree support for the Power Supply core: the core now
automatically populates supplied_from hierarchy from the device tree.
With these patches chargers and batteries can now lookup each other
without the board files support shim. Rhyland Klein at NVIDIA did the
work;
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using the
AB85xx core and depends on some recent changes to it, so that is why the
driver comes through the battery tree. It has an appropriate ack from
the hwmon maintainer (i.e. Guenter Roeck). Martin Persson at ST-Ericsson
and Hongbo Zhang at Linaro authored the driver;
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The changes
touch mfd parts, but these were acked by the appropriate MFD maintainer
(i.e. Samuel Ortiz). Lee Jones at Linaro did most of the work and lead
the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones;
- Versatile Express poweroff driver moved into drivers/power/reset/.
- Tree-wise: use devm_kzalloc() where appropriate;
- Tree-wise: dev_pm_ops cleanups/fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=5BdE
-----END PGP SIGNATURE-----
Merge tag 'for-v3.10' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- OpenFirmware/DeviceTree support for the Power Supply core: the core
now automatically populates supplied_from hierarchy from the device
tree. With these patches chargers and batteries can now lookup
each other without the board files support shim. Rhyland Klein at
NVIDIA did the work
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using
the AB85xx core and depends on some recent changes to it, so that
is why the driver comes through the battery tree. It has an
appropriate ack from the hwmon maintainer (i.e. Guenter Roeck).
Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored
the driver
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The
changes touch mfd parts, but these were acked by the appropriate
MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of
the work and lead the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones
- Versatile Express poweroff driver moved into drivers/power/reset/
- Tree-wide: use devm_kzalloc() where appropriate
- Tree-wide: dev_pm_ops cleanups/fixes"
* tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits)
pm2301-charger: Fix suspend/resume
charger-manager: Use kmemdup instead of kzalloc + memcpy
power_supply: Populate supplied_from hierarchy from the device tree
power_supply: Add core support for supplied_from
power_supply: Define Binding for power-supplies
rx51_battery: Fix reporting temperature
hwmon: Add ST-Ericsson ABX500 hwmon driver
ab8500_bmdata: Export abx500_res_to_temp tables for hwmon
ab8500_{bmdata,fg}: Add const attributes to some data arrays
ab8500_bmdata: Eliminate CamelCase warning of some variables
ab8500_btemp: Make ab8500_btemp_get* interfaces public
goldfish_battery: Use resource_size()
lp8788-charger: Use PAGE_SIZE for the sysfs read operation
max8925_power: Use devm_kzalloc()
da9030_battery: Use devm_kzalloc()
da9052-battery: Use devm_kzalloc()
ds2760_battery: Use devm_kzalloc()
ds2780_battery: Use devm_kzalloc()
gpio-charger: Use devm_kzalloc()
isp1704_charger: Use devm_kzalloc()
...
TMP432 is similar to TMP431 with a second external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Each of ST-Ericsson X500 chip set series consists of both ABX500 and DBX500
chips. This is ABX500 hwmon driver, where the abx500.c is a common layer for
all ABX500s, and the ab8500.c is specific for AB8500 chip. Under this designed
structure, other chip specific files can be added simply using the same common
layer abx500.c.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
NCT6775, NCT6776, and NCT6779 have a number of variants with the same
chip ID but different chip labels. Add text "or compatible" to the
message displayed when the driver is loaded and rephrase the Kconfig
entry to reflect that it also supports compatible chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP431 is compatible to TMP401.
Also add support for additional I2C addresses supported by TMP411B
and TMP411C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far the driver reported the voltage on VAUX as "vout2". This was not
entirely appropriate as it is not an output voltage, and complicates
the code. Use the new virtual "VMON" register set and report the voltage
as "vmon" instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some sysfs attributes are only supported on LTC2978 and not on LTC3880.
Update documentation to reflect which attributes are supported for which chips.
Output current attributes supported on LTC3880 were described as providing
input current values. Fix text to reflect that the attributes provide output
current values.
"reset history" attribute descriptions were misleading and seemed to imply
that all history was reset when writing a single attribute. Replace with more
accurate text.
Replace 'internal temperature" with "chip temperature". Temperature limits
not only apply to the chip temperature, but also to external temperatures
on LTC3880, so remove the word "chip" from the attribute description.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT677X series support weighted fan control. In this mode, a secondary
temperature source is used in addition to the primary temperature source to
control fan speed. Add support for this feature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver will replace the w83627ehf driver for NCT6775F and NCT6776F,
and provides support for NCT6779D.
This patch provides support for voltage monitor attributes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7310/adt7320 is the SPI version of the adt7410/adt7420. The register map
layout is a bit different, i.e. the register addresses differ between the two
variants, but the bit layouts of the individual registers are identical. So both
chip variants can easily be supported by the same driver. The issue of non
matching register address layouts is solved by a simple look-up table which
translates the I2C addresses to the SPI addresses.
The patch moves the bulk of the adt7410 driver to a common module that will be
shared by the adt7410 and adt7310 drivers. This common module implements the
driver logic and uses a set of virtual functions to perform IO access. The
adt7410 and adt7310 driver modules provide proper implementations of these IO
accessor functions for I2C respective SPI.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7410 driver supports the ADT7420, but its documentation file
makes no mention of that. Add this refrence, and a brief a description
of the differences between the ADT7410 and the ADT7420.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Links to datasheets are no longer valid. Provide links to product information
instead (which provides links to the datasheets and is hopefully more
persistent).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Most of the hwmon driver documentation still listed my old invalid e-mail
address. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
MAX34460 is a PMBus 12-Channel Voltage Monitor & Sequencer.
MAX34461 is a PMBus 16-Channel Voltage Monitor & Sequencer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the ZL6100 compatible chips support monitoring a separate voltage pin,
VMON (ZL2004) or VDRV (ZL91xx). Report it as in2 / vmon.
The chips support implicit warning limits for VMON/VDRV, as percentage of the
respective critical voltage. Support by reading/writing the critical voltages
and calculating the associated warning voltages.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.
Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for temp1_min_alarm and temp1_max_alarm
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup; dropped platform data and interrupt support]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LM73 supports four A/D conversion resolutions. The default used by
the existing lm73 driver is the chip's default, 11-bit (0.25 C/LSB).
This patch enables changing of this resolution from userspace via the
update_interval sysfs attribute. Full details on usage are included in
Documentation/hwmon/lm73.
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Assume that IT8771E and IT8772E are fully compatible with IT8728F.
IT8771E support contributed by Kelly Anderson.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
IT8721 and IT8728 support Intel PECI temperature reporting. Each sensor
can be programmed to display the temperature reported on the PECI interface.
If configured for Intel PECI, the driver reported the wrong sensor type for
the respective thermal sensor. Fix the code to correctly report it as
"Intel PECI (6)".
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
TjMax for the CE4100 series of Atom CPUs was previously reported to be
110 degrees C.
cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170,
reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz"
with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants
to the tjmax table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Jean Delvare <khali@linux-fr.org>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Rob Landley <rob@landley.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This Patch adds support for mcp3221 chip to the
mcp3021 driver.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA220 is register compatible to INA219, and INA230 is register compatible to
INA226, so all we need to do is to add name aliases for those two chips.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for LM74 and LM71 to LM70 driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Removing the 3wire limitation on LM70 as the component also allows
operation on 4wire SPI bus
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX197 is an A/D converter, made by Maxim. This driver currently
supports the MAX197, and MAX199. They are both 8-Channel, Multi-Range,
5V, 12-Bit DAS with 8+4 Bus Interface and Fault Protection.
The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to
10V, while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch brings basic support for the Analog Devices ADT7410 temperature
sensor. The following functionality has been implemented:
* get current temperature
* get/set minimum, maximum and critical temperature
* get/set hysteresis
* get alarm events for minimum, maximum and critical temperature
All implemented sysfs attributes have been sucessfully tested at temperatures
of 15°C to 40°C.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is a new driver for the Honeywell Humidicon HIH-6130/HIH-6131 humidity sensor.
The driver is based on the existing Sensiron sht21 driver with the necessary changes
to the probe, update_measurements and conversion functions necessary to use the
Honeywell sensors.
There's no difference between the 6130 & 6131 other than the 6131 having an external
condensation filter attached.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
devres functions are the preferred means to allocate resources in hwmon drivers.
Document it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
The DA9052 PMIC provides an Analogue to Digital Converter with 10 bits
resolution and 10 channels.
This patch monitors the DA9052 PMIC's ADC channels mostly for battery
parameters like battery temperature, junction temperature, battery
current etc.
This patch is functionally tested on Samsung SMDKV6410
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: __init --> __devinit for probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck
Justin Maggard
Constantine Shulyupin
Jean Delvare
Roger Lucas
Maciej S. Szmigiero
Beomho Seo
Vadim V. Vlasov
Thomas Lorblanches
Kevin Hilman
Bartosz Golaszewski
Patrick Titiano
Michael Thalmeier
Andreas Werner
Aravind Gopalakrishnan
Kamil Debski
Neelesh Gupta
Zhu, Richard \(NSN - CN/Beijing\)
Johannes Pointner
Frans Klaver
Heiko Schocher
Scott Kanowitz
Naveen Krishna Chatradhi
Tomas Pop
Linus Torvalds
Rudolf Marek
Jean Delvare
Wei Ni
Shane Huang
William Markezana
Wei Hu
Masanari Iida
Stefan Huber
Evgeniy Dushistov
Arnaud Ebalard
Tang Yuantian
Robert Coulson
Stephen Rothwell
Hongbo Zhang
Lars-Peter Clausen
Chris Verges
Ashish Jangam
Guillaume Roguez
Vivien Didelot
Arnd Bergmann
Andreas Herrmann
Pawel Moll
Kees Cook
Peter Meerwald
Oleksij Rempel
Len Brown
Amit Daniel Kachhap
Sven Schuchmann
Christophe Leroy
Hartmut Knaack
Iain Paton