Change the case that sends packets with "too short inner packet" to
include part of ethernet header, to make the trap to be triggered due to
the correct reason.
According to ASIC arch, the trap is triggered if overlay packet length is
less than 18B, and the minimum inner packet should include source MAC and
destination MAC.
Till now the case passed because one of the reserved bits in VxLAN
header was used. This issue was found while adding an equivalent test
for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test configures VxLAN with IPv6 underlay and verifies that the
expected traps are triggered under the right conditions.
The test is similar to the existing IPv4 test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-2 and above, which support up to four
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-1 switches, which support up to five
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify FDB vetos of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_fdb_veto.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.
Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.
The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to verify configuration of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Add separated test cases for learning which is not supported for IPv6
and for UDP checksum flags which are different from IPv4 flags.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.
Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.
The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Rename some functions to include "ipv4", so the next patch will add
equivalent functions for IPv6.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a test case to verify that VxLAN with IPv6 underlay
is forbidden.
Remove this test case as support for VxLAN with IPv6 underlay was added
by the previous patch.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test case to cover the bug fixed by the previous patch.
Edit the MAC address of one netdev so that it matches the MAC address of
the second netdev. Verify that the two MAC profiles were consolidated by
testing that the MAC profiles occupancy decreased by one.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TBF can be used as a root qdisc, with the usual ETS/RED/TBF hierarchy below
it. This use should now be offloaded. Add a test that verifies that it is.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After adding the previous patches, the constraint that all the router
interface MAC addresses have the same prefix is no longer relevant.
Remove the test cases that validated that this constraint is honored.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When all the RIF MAC profiles are in use, test that it is possible to
change the MAC of a netdev (i.e., a RIF) when its MAC profile is not
shared with other RIFs. Test that replacement fails when the MAC profile
is shared.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that MAC profile changes are indeed applied and that packets are
forwarded with the correct source MAC.
Output example:
$ ./rif_mac_profiles.sh
TEST: h1->h2: new mac profile [ OK ]
TEST: h2->h1: new mac profile [ OK ]
TEST: h1->h2: edit mac profile [ OK ]
TEST: h2->h1: edit mac profile [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the maximum number of supported RIF MAC profiles using
devlink-resource and verify that all available MAC profiles can be utilized
and that an error is generated when user space tries to exceed this number.
Output example in Spectrum-2:
$ TESTS='rif_mac_profile' ./resource_scale.sh
TEST: 'rif_mac_profile' 4 [ OK ]
TEST: 'rif_mac_profile' overflow 5 [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of iterating over all the available trap policers, only perform
the tests with three policers: The first, the last and the one in the
middle of the range. On a Spectrum-3 system, this reduces the run time
from almost an hour to a few minutes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop objects tests configure dummy reachable neighbours so that
the nexthops will have a MAC address and be programmed to the device.
Since these are dummy reachable neighbours, they can be transitioned by
the kernel to a failed state if they are around for too long. This can
happen, for example, if the "TIMEOUT" variable is configured with a too
high value.
Make the tests more robust by configuring the neighbours as permanent,
so that the tests do not depend on the configured timeout value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of mlxsw-specific selftests currently detect whether they are run
on a compatible machine, and bail out silently when not. These tests are
however done in a somewhat impenetrable manner by directly comparing PCI
IDs against a blacklist or a whitelist, and bailing out silently if the
machine is not compatible.
Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying
the supported machines in a human-readable manner. If the current machine
is incompatible, the helper emits a SKIP message and returns an error code,
based on which the caller can gracefully bail out in a suitable way. This
allows a more readable conditions such as:
mlxsw_only_on_spectrum 2+ || return
Convert all existing open-coded guards to the new helper. Also add two new
guards to do_mark_test() and do_drop_test(), which are supported only on
Spectrum-2+, but the corresponding check was not there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is a bit strange in that it is perhaps more manual than
others: it does not transmit a clear OK/FAIL verdict, because user space
does not have synchronous feedback from the kernel. If a hardware access
fails, it is in deferred context.
Nonetheless, on sja1105 I have used it successfully to find and solve a
concurrency issue, so it can be used as a starting point for other
driver maintainers too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is a bit strange in that it is perhaps more manual than
others: it does not transmit a clear OK/FAIL verdict, because user space
does not have synchronous feedback from the kernel. If a hardware access
fails, it is in deferred context.
Nonetheless, on sja1105 I have used it successfully to find and solve a
concurrency issue, so it can be used as a starting point for other
driver maintainers too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This checks that various qdisc configurations either are or are not
offloaded.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a variant of ECN test that uses qdisc marked counter (supported on
Spectrum-3 and above) instead of the aggregate ethtool ecn_marked counter.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add do_mark_test(), which is to do_ecn_test() like do_drop_test() is to
do_red_test(): meant to test that actions on the RED mark qevent block are
offloaded, and executed on ECN-marked packets.
The test splits install_qdisc() into its constituents, install_root_qdisc()
and install_qdisc_tcX(). This is in order to test that when mirroring is
enabled on one TC, the other TC does not mirror.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These variables are cut'n'pasted from other functions in the file and not
actually used.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of adding same test for GRE tunnel with IPv6 underlay, missing
bytes for key were found.
mausezahn does not fill zeros between two colons, so send them
explicitly. For example, use "00:00:00:E9:" instead of ":E9:"
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of adding same test for GRE tunnel with IPv6 underlay, an
optional improvement was found - call ipip_payload_get from
ecn_payload_get, so do not duplicate the code which creates the payload.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of adding same test for GRE tunnel with IPv6 underlay, wrong
alignments were found, fix them.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 underlay support was added, add test to check that "decap_error" trap
is triggered under the right conditions and that devlink counters increase.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kselftest fixes update for Linux 5.15-rc5 consists of a fix
to implicit declaration warns in drivers/dma-buf test.
-----BEGIN PGP SIGNATURE-----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=t85S
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-fixes-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"A fix to implicit declaration warns in drivers/dma-buf test"
* tag 'linux-kselftest-fixes-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: drivers/dma-buf: Fix implicit declaration warns
For this test we are exercising the VCAP ES0 block's ability to match on
a packet with a given VLAN ID, and push an ES0 TAG A with a VID derived
from VID_A_VAL plus the classified VLAN.
$eth3.200 is the generator port
$eth0 is the bridged DUT port that receives
$eth1 is the bridged DUT port that forwards and rewrites VID 200 to 300
on egress via VCAP ES0
$eth2 is the port that receives from the DUT port $eth1
Since the egress rewriting happens outside the bridging service, VID 300
does not need to be in the bridge VLAN table of $eth1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be one more VLAN modification selftest added, this time for
egress. Rename the one that exists right now to be more specific.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like when I wrote the selftests I was using a network manager that
brought up the ports automatically. In order to not rely on that, let
the script open them up.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udmabuf has the following implicit declaration warns:
udmabuf.c:30:10: warning: implicit declaration of function 'open';
udmabuf.c:42:8: warning: implicit declaration of function 'fcntl'
These are caused due to not including fcntl.h and including just
linux/fcntl.h. Fix it to include fcntl.h which will bring in the
linux/fcntl.h. In addition, define __EXPORTED_HEADERS__ to bring in
F_ADD_SEALS and F_SEAL_SHRINK defines and fix the following error
that show up when just fcntl.h is included.
udmabuf.c:45:21: error: 'F_ADD_SEALS' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~
udmabuf.c:45:34: error: 'F_SEAL_SHRINK' undeclared
45 | ret = fcntl(memfd, F_ADD_SEALS, F_SEAL_SHRINK);
| ^~~~~~~~~~~~~
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest for checking mq children are visible after ethtool -L.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hard drop counter check testcase, to make sure netdevsim driver
properly handles the devlink hard drop counters get/set callbacks.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit referenced below, a check was added to devlink_lib that
asserts the existence of a devlink device referenced by $DEVLINK_DEV.
Unfortunately, several netdevsim tests point DEVLINK_DEV at a device that
does not exist at the time that devlink_lib is sourced. Thus these tests
spuriously fail.
Fix this by introducing an override. By setting DEVLINK_DEV to an empty
string, the user declares their intention to handle DEVLINK_DEV management
on their own.
In all netdevsim tests that use devlink_lib and set DEVLINK_DEV, set
instead an empty DEVLINK_DEV just before sourcing devlink_lib, and set it
to the correct value right afterwards.
Fixes: 557c4d2f78 ("selftests: devlink_lib: add check for devlink device existence")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several tests do not set some ports down as part of their cleanup(),
resulting in IPv6 link-local addresses and associated routes not being
deleted.
These leaks were found using a BPF tool that monitors ASIC resources.
Solve this by setting the ports down at the end of the tests.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To check how many routes are installed in hardware, the test runs "ip
route" and greps for "offload", which includes routes with state
"offload_failed".
Till now, this wrong check was not found because after one failure in
route insertion, the driver moved to "abort" mode, which means that user
cannot try to add more routes.
The previous patch removed the abort mechanism and now failed routes are
counted as offloaded.
Fix this by not considering routes with "offload_failed" flag as
offloaded.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that netdevsim correctly implements devlink ops callbacks
that set node as a parent of devlink leaf or node rate object.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that it is possible to create, delete and set min/max tx
rate of devlink rate node on netdevsim VF.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that netdevsim VFs can set and retrieve shared/max tx
rate through new devlink API.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test verifies that all netdevsim VF ports have rate leaf object created
by default.
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the two users of this helper have been converted to iproute2 dcb,
it is not necessary anymore. Drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a dedicated tool for configuration of DCB in iproute2 now. Use it
in the selftest instead of mlnx_qos.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen
Jakub Kicinski
Danielle Ratson
Petr Machata
Ido Schimmel
Vladimir Oltean
David S. Miller
Linus Torvalds
Shuah Khan
Oleksandr Mazur
Dmytro Linkin