Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations
to fix overflow issues with 32-bit architectures
Plus various cleanups in several drivers.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEiHPvMQj9QTOCiqgVyx8mb86fmYEFAl8p1d8ACgkQyx8mb86f
mYGECw//RIhcVCvmSgnhRnAhN0EOJrl/QzFkukdl5MGnJIWQyW/od/Hjjg0A31VS
GdrUGilP0vDwzy7QD9N1CgGaYM42yP0OlhlfcvRoYXGJsPhCcWMGT2EnNsbuCpYj
O1CR/fjgYSrNmU1TvUKVLTnaCikckP3NGlbJVXViPd4LyP8kgSp2ZTqNGOOw5ByT
tAryzG2TDg/0V1aB/jniTPsZtp3Ezw4I0+DtGfXNKLw6LBZaMPVoLuDqLAv3KgUa
m2sZ1CG1gzvflLznDtb03g9xakwdq1Nj0xx0+t3tJtztte2FG3AsXlA3feAXZAL8
cH83xXUKFhb40n90RhGt6DWwKbvygtTuCe+6EaixYhesHvU8sC36FMBxCp7dSPUb
0ppJx0cmQB/3EMOsSzl7+dhwos/9yGkkGKJi1bPv0zYHq4BxtTYcV2vkx7q+DKHA
86e/IQNdoLqPOiGD+oFHAZzyJy7GEcVT054I7wuGrkHXlsm4aJIxOYOxFgRmcrjl
/RGGdPypMWxNE3NwoNOOHFBiKVi8Bh26JpncLaNmY96fHEhsUtfNICFxIVFgaZCt
sOa+pZjPbQtR3UAMnB3ZZfvzBELzAgY/FMm6fdVfrpIukK3dss3CIlNbZVm4P+0a
CmOdA4a8EMQPDOFcFxeyv+0/PhIdf/tAZBtRDkT7E1oeaqfb18Q=
=nMNN
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations to fix
overflow issues with 32-bit architectures
Plus various cleanups in several drivers"
* tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (adc128d818) Fix advanced configuration register init
hwmon: (axi-fan-control) remove duplicate macros
hwmon: (i5k_amb, vt8231) Drop uses of pci_read_config_*() return value
hwmon: (sparx5) Make symbol 's5_temp_match' static
hwmon: (corsair-cpro) add reading pwm values
hwmon: sparx5: Add Sparx5 SoC temperature driver
dt-bindings: hwmon: Add Sparx5 temperature sensor
hwmon: (tmp401) Replace HTTP links with HTTPS ones
hwmon: (lm95234) Replace HTTP links with HTTPS ones
hwmon: (lm90) Replace HTTP links with HTTPS ones
hwmon: (k8temp) Replace HTTP links with HTTPS ones
hwmon: (jc42) Replace HTTP links with HTTPS ones
hwmon: (ina2xx) Replace HTTP links with HTTPS ones
hwmon: (ina209) Replace HTTP links with HTTPS ones
hwmon: Replace HTTP links with HTTPS ones
docs: hwmon: Replace HTTP links with HTTPS ones
hwmon: (adm1025) Replace HTTP links with HTTPS ones
hwmon: add Corsair Commander Pro driver
hwmon: (max6697) Allow max6581 to create tempX_offset
hwmon: (tmmp513) Replace HTTP links with HTTPS links
...
If the operation mode is non-zero and an external reference voltage is set,
first the operation mode is written to the advanced configuration register,
followed by the externel reference enable bit,
resetting the configuration mode to 0.
To fix this, first compose the value of the advanced configuration register
based on the configuration mode and the external reference voltage.
The advanced configuration register is then written to the device,
if it is different from the default register value (0x0).
Signed-off-by: Roy van Doormaal <roy.van.doormaal@prodrive-technologies.com>
Link: https://lore.kernel.org/r/20200728151846.231785-1-roy.van.doormaal@prodrive-technologies.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These macros are also present in the "include/linux/fpga/adi-axi-common.h"
file which is included in this driver.
This patch removes them from the AXI Fan Control driver. No sense in having
them in 2 places.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200803054311.98174-1-alexandru.ardelean@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of pci_read_config_*() may not indicate a device error.
However, the value read by these functions is more likely to indicate
this kind of error. This presents two overlapping ways of reporting
errors and complicates error checking.
It is possible to move to one single way of checking for error if the
dependency on the return value of these functions is removed, then it
can later be made to return void.
Remove all uses of the return value of pci_read_config_*().
Check the actual value read for ~0. In this case, ~0 is an invalid
value thus it indicates some kind of error.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Link: https://lore.kernel.org/r/20200801112446.149549-11-refactormyself@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The sparse tool complains as follows:
drivers/hwmon/sparx5-temp.c:150:27: warning:
symbol 's5_temp_match' was not declared. Should it be static?
This variable is not used outside of sparx5-temp.c, this commit
marks it static.
Fixes: c2cb4b5777e1 ("hwmon: sparx5: Add Sparx5 SoC temperature driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200721134919.34033-1-weiyongjun1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds the possibility for reading pwm values.
These can not be read if the device is controlled via
fan_target or a fan curve and will return an error in
this case. Since an error is expected, this adds some
rudimentary error handling.
Changes:
- add CTL_GET_FAN_PWM and use it via get_data
- pwm returns -ENODATA if the device returns error 0x12
- fan_target now returns -ENODATA when the driver is
started or a pwm value is set.
- add ccp_get_errno to determine errno from device error.
- get_data now has a parameter to determine whether
to read one or two bytes of data.
- update documentation
- fix missing surname in MAINTAINERS
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719181530.60878-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719180521.60811-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719175512.60745-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200713140028.34775-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is v7 of a driver for the Corsair Commander Pro.
It provides sysfs attributes for:
- Reading fan speed
- Reading temp sensors
- Reading voltage values
- Writing pwm and reading last written pwm
- Reading fan and temp connection status
It is an usb driver, so it needs to be ignored by usbhid.
The Corsair Commander Pro is a fan controller and provides
no means for user interaction.
The two device numbers are there, because there is a slightly
different version of the same device. (Only difference
seem to be in some presets.)
Squashed:
hwmon: (corsair-cpro) add fan_target
This adds fan_target entries to the corsair-cpro driver.
Reading the attribute from the device does not seem possible, so
it returns the last set value (same as pwm).
send_usb_cmd now has one more argument, which is needed for the
fan_target command.
hwmon: corsair-cpro: Change to HID driver
This changes corsair-cpro to a hid driver using hid reports.
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200626055936.4441-1-mail@mariuszachmann.de
Link: https://lore.kernel.org/r/20200709141413.30790-1-mail@mariuszachmann.de
[groeck: Squashed follow-up patches to avoid changes in HID code]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200703185657.15329-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using s64 type, instead of long type, for internal calculations and for
the sysfs interface.
This allows 64-bit values to appear correctly on 32-bit kernels.
As wattage is reported in microwatts, monitoring a power supply over
2KW requires this.
Although it may seem unlikely to run a 32-bit kernel on such a large
machine, enterprise servers often include a BMC, and the BMC might be
running a 32-bit kernel.
Signed-off-by: Josh Lehan <krellan@google.com>
[groeck: Removed Change-Id and other tags, reformatted description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
add a 16-bit pre-scaled voltage mode to adc and clarify that existing
pre-scaled mode is 24bit.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1591714640-10332-3-git-send-email-tharvey@gateworks.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adm1278 temp attribute need it for openbmc platform .
This feature not enabled by default, so PMON_CONFIG needs to enable it.
Signed-off-by: Manikandan Elumalai <manikandan.hcl.ers.epl@gmail.com>
Link: https://lore.kernel.org/r/20200622153727.GA9347@cnn
[groeck: Split long line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This allows manual PWM control without the BIOS fighting back on Dell
Latitude 5480.
Signed-off-by: Jeffrey Lin <jeffrey@icurse.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200621045246.929649-1-jeffrey@icurse.nl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The variable res is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200610123638.1133428-1-colin.king@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It has been observed that Toshiba DT01ACA family drives have
WRITE FPDMA QUEUED command timeouts and sometimes just freeze until
power-cycled under heavy write loads when their temperature is getting
polled in SCT mode. The SMART mode seems to be fine, though.
Let's make sure we don't use SCT mode for these drives then.
While only the 3 TB model was actually caught exhibiting the problem let's
play safe here to avoid data corruption and extend the ban to the whole
family.
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Link: https://lore.kernel.org/r/0cb2e7022b66c6d21d3f189a12a97878d0e7511b.1595075458.git.mail@maciej.szmigiero.name
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SMATCH detected a potential buffer overflow in the manipulation of
hwmon_attributes array inside the scmi_hwmon_probe function:
drivers/hwmon/scmi-hwmon.c:226
scmi_hwmon_probe() error: buffer overflow 'hwmon_attributes' 6 <= 9
Fix it by statically declaring the size of the array as the maximum
possible as defined by hwmon_max define.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20200715121338.GA18761@e119603-lin.cambridge.arm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Stefan Dietrich reports invalid temperature source messages on Asus Formula
XII Z490.
nct6775 nct6775.656: Invalid temperature source 28 at index 0,
source register 0x100, temp register 0x73
Debugging suggests that temperature source 28 reports the CPU temperature.
Let's assume that temperature sources 28 and 29 reflect "PECI Agent {0,1}
Calibration", similar to other chips of the series.
Reported-by: Stefan Dietrich <roots@gmx.de>
Cc: Stefan Dietrich <roots@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Issue:
When PEC is enabled, binding adm1272 to the adm1275 would
fail due to PEC error. See below:
adm1275: probe of xxxx failed with error -74
Diagnosis:
Per the datasheet of adm1272, adm1278, adm1293 and amd1294,
PMON_CONFIG (0xd4) is 16bits wide. On the other hand,
PMON_CONFIG (0xd4) for adm1275 is 8bits wide. The driver should not
assume everything is 8bits wide and read only 8bits from it.
Solution:
If it is adm1272, adm1278, adm1293 and adm1294, use i2c_read_word.
Else, use i2c_read_byte
Testing:
Binding adm1272 to the driver.
The change is only tested on adm1272.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20200709040612.3977094-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch fixes a bug which does not let FAN mode to be changed from
sysfs(pwm1_enable). i.e pwm1_enable can not be set to 3, it will always
remain at 0.
This is caused because the device driver handles the result of
"read_u8_from_i2c(client, REG_FAN_CONF1, &conf_reg)" incorrectly. The
driver thinks an error has occurred if the (result != 0). This has been
fixed by changing the condition to (result < 0).
Signed-off-by: Vishwas M <vishwas.reddy.vr@gmail.com>
Link: https://lore.kernel.org/r/20200707142747.118414-1-vishwas.reddy.vr@gmail.com
Fixes: 9df7305b5a ("hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller")
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The energy counters of certain models seems to be reporting
inconsistent values. Hence, match for the supported models.
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Fixes: 8abee9566b ("hwmon: Add amd_energy driver to report energy counters")
Link: https://lore.kernel.org/r/20200706171715.124993-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
aspeed_create_fan() reads a pwm_port value using of_property_read_u32().
If pwm_port will be more than ARRAY_SIZE(pwm_port_params), there will be
a buffer overflow in
aspeed_create_pwm_port()->aspeed_set_pwm_port_enable(). The patch fixes
the potential buffer overflow.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20200703111518.9644-1-novikov@ispras.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix a typo in SENSORS_IR35221 option: module name should be "ir35221"
instead of "ir35521".
Fixes: 8991ebd9c9 ("hwmon: (pmbus) Add client driver for IR35221")
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200702221349.18139-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Although it rarely happens, we should call free_capabilities()
if error happens after read_capabilities() to free allocated strings.
Fixes: de584afa5e ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Link: https://lore.kernel.org/r/20200625043242.31175-1-misono.tomohiro@jp.fujitsu.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per the datasheet for max6697, OVERT mask and ALERT mask are different.
For example, the 7th bit of OVERT is the local channel but for alert
mask, the 6th bit is the local channel. Therefore, we can't apply the
same mask for both registers. In addition to that, the max6697 driver
is supposed to be compatibale with different models. I manually went over
all the listed chips and made sure all chip types have the same layout.
Testing;
mask value of 0x9 should map to 0x44 for ALERT and 0x84 for OVERT.
I used iotool to read the reg value back to verify. I only tested this
change on max6581.
Reference:
https://datasheets.maximintegrated.com/en/ds/MAX6581.pdfhttps://datasheets.maximintegrated.com/en/ds/MAX6697.pdfhttps://datasheets.maximintegrated.com/en/ds/MAX6699.pdf
Signed-off-by: Chu Lin <linchuyuan@google.com>
Fixes: 5372d2d71c ("hwmon: Driver for Maxim MAX6697 and compatibles")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
added support for multi-phase pmbus devices. However, when calling
pmbus_add_sensor() for fans, the patch swapped the `page` and `reg`
attributes. As a result, the fan speeds were reported as 0 RPM on my device.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Fixes: 16358542f3 ("hwmon: (pmbus) Implement multi-phase support")
Cc: stable@vger.kernel.org # v5.7+
Link: https://lore.kernel.org/r/449bc9e6c0e4305581e45905ce9d043b356a9932.1592904387.git.jan.kundrat@cesnet.cz
[groeck: Fixed references to offending commit]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Clang-based kernel building with W=1 warns that some static const
variables are unused:
drivers/hwmon/bt1-pvt.c:67:30: warning: unused variable 'poly_temp_to_N' [-Wunused-const-variable]
static const struct pvt_poly poly_temp_to_N = {
^
drivers/hwmon/bt1-pvt.c:99:30: warning: unused variable 'poly_volt_to_N' [-Wunused-const-variable]
static const struct pvt_poly poly_volt_to_N = {
^
Indeed these polynomials are utilized only when the PVT sensor alarms are
enabled. In that case they are used to convert the temperature and
voltage alarm limits from normal quantities (Volts and degree Celsius) to
the sensor data representation N = [0, 1023]. Otherwise when alarms are
disabled the driver only does the detected data conversion to the human
readable form and doesn't need that polynomials defined. So let's mark the
Temp-to-N and Volt-to-N polynomials with __maybe_unused attribute.
Note gcc with W=1 doesn't notice the problem.
Fixes: 87976ce282 ("hwmon: Add Baikal-T1 PVT sensor driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200603000753.391-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
... into the global msr-index.h header because they're used in multiple
compilation units. Sort the MSR list a bit. Update the msr-index.h copy
in tools.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200608164847.14232-1-bp@alien8.de
to fixup conflicts in arch/x86/kernel/cpu/mce/core.c so MCE specific follow
up patches can be applied without creating a horrible merge conflict
afterwards.
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.
The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.
The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For hwmon drivers using the hwmon_device_register_with_info() API, it
is desirable to have a generic notification mechanism available. This
mechanism can be used to notify userspace as well as the thermal
subsystem if the driver experiences any events, such as warning or
critical alarms.
Implement hwmon_notify_event() to provide this mechanism. The function
generates a sysfs event and a udev event. If the device is registered
with the thermal subsystem and the event is associated with a temperature
sensor, also notify the thermal subsystem that a thermal event occurred.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building this driver with "clang -O3" produces a link error
after the compiler partially unrolls the loop and 256ms
becomes a compile-time constant that triggers the check
in udelay():
ld.lld: error: undefined symbol: __bad_udelay
>>> referenced by applesmc.c
>>> hwmon/applesmc.o:(read_smc) in archive drivers/built-in.a
I can see no reason against using a sleeping function here,
as no part of the driver runs in atomic context, so instead use
usleep_range() with a wide range and use jiffies for the
end condition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200527135207.1118624-1-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The timeout module parameter should not be used for setting the default
timeout. Because, if you set the timeout = 0, the default timeout will
be meaningless. And the timeout module parameter of 0 means "no timeout
module parameter specified".
Signed-off-by: Yuechao Zhao <yuechao.zhao@advantech.com.cn>
Link: https://lore.kernel.org/r/1590560219-41328-1-git-send-email-yuechao.zhao@advantech.com.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for retrieving Tdie and Tctl on AMD Renoir (4000-series
Ryzen CPUs).
It appears SMU offsets for reading current/voltage and CCD temperature
have changed for this generation (reads from currently used offsets
yield zeros), so those features cannot be enabled so trivially.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200510204842.2603-3-amonakov@ispras.ru
This patch adds hwmon based amd_energy driver support for
family 17h processors from AMD.
The driver provides following interface to the userspace
1. Reports the per core consumption
* file: "energy%d_input", label: "Ecore%03d"
2. Reports per socket energy consumption
* file: "energy%d_input", label: "Esocket%d"
3. To, increase the wrap around time of the socket energy
counters, a 64bit accumultor is implemented.
4. Reports scaled energy value in Joules.
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200519155011.56184-1-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Maxim MAX6654 to the lm90 driver.
The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: Josh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: zhouchuangao <zhouchuangao@xiaomi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16601 is a VR13.HC Dual-Output Voltage Regulator Chipset,
implementing a (8+1) multiphase synchronous buck converter.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'currpage' and 'currphase' variables in struct pmbus_data are used by
the PMBus core to determine if the phase or page value has changed. Both
are initialized with values which are never expected to be set in the code
to ensure that the first page/phase write operation is actually performed.
This is not well explained and occasionally causes confusion. Change the
type of both variables to s16 and initialize with -1 to ensure that the
initial value never matches a requested value, and clarify that this
value means "unknown/unset".
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Linus Torvalds
Roy van Doormaal
Alexandru Ardelean
Saheed O. Bolarinwa
Ingo Molnar
Wei Yongjun
Marius Zachmann
Lars Povlsen
Alexander A. Klimov
Chu Lin
Josh Lehan
Ugur Usug
Tim Harvey
Manikandan Elumalai
Jeffrey Lin
Wang Qing
Colin Ian King
Maciej S. Szmigiero
Cristian Marussi
Guenter Roeck
Vishwas M
Naveen Krishna Chatradhi
Evgeny Novikov
Tao Ren
Misono Tomohiro
Jan Kundrát
Serge Semin
Borislav Petkov
Thomas Gleixner
Arnd Bergmann
Yuechao Zhao
Alexander Monakov
hailizheng
zhouchuangao