There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
Pull OPP (Operating Performance Points) updates for 5.11-rc1 from
Viresh Kumar:
"This contains the following updates:
- Allow empty (node-less) OPP tables in DT for passing just the
dependency related information (Nicola Mazzucato).
- Fix a potential lockdep in OPP core and other OPP core cleanups
(Viresh Kumar).
- Don't abuse dev_pm_opp_get_opp_table() to create an OPP table, fix
cpufreq-dt driver for the same (Viresh Kumar).
- dev_pm_opp_put_regulators() accepts a NULL argument now, updates to
all the users as well (Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
opp: Don't return opp_dev from _find_opp_dev()
opp: Allocate the OPP table outside of opp_table_lock
opp: Always add entries in dev_list with opp_table->lock held
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra check. Drop them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The VNCSI_IFMD register controls the data expansion mode and the
channel routing between the CSI-2 receivers and VIN instances.
According to the chip manual revision 2.20 not all fields are available
for all the SoCs:
- V3M, V3H and E3 do not support the DES1 field has they do not feature
a CSI20 receiver.
- D3 only supports parallel input, and the whole register shall always
be written as 0.
Inspect the per-SoC channel routing table where the available CSI-2
instances are reported and configure VNCSI_IFMD accordingly.
This patch supports this BSP change commit:
https://github.com/renesas-rcar/linux-bsp/commit/f54697394457
("media: rcar-vin: Fix VnCSI_IFMD register access for r8a77990")
[hverkuil: replace BSP commit ID with BSP URL]
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The GE2D is a 2D accelerator with various features like configurable
blitter with alpha blending, frame rotation, scaling, format conversion
and colorspace conversion.
The driver implements a Memory2Memory VB2 V4L2 streaming device permitting:
- 0, 90, 180, 270deg rotation
- horizontal/vertical flipping
- source cropping
- destination compositing
- 32bit/24bit/16bit format conversion
This adds the support for the GE2D version found in the AXG SoCs Family.
The missing features are:
- Source scaling
- Colorspace conversion
- Advanced alpha blending & blitting options
Is passes v4l2-compliance:
SHA: ea16a7ef13a902793a5c2626b0cefc4d956147f3, 64 bits, 64-bit time_t
[hverkuil: add missing linux/bitfield.h include]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For historical reasons, stateful codec controls are named
as {}_MPEG_{}. While we can't at this point sanely
change all control IDs (such as V4L2_CID_MPEG_VIDEO_VP8_FRAME_HEADER),
we can least change the more meaningful macros such as classes
macros.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The debugfs_create_dir() function never returns NULLs so this code will
never be executed. It's not intended that callers will check for
debugfs errors in the normal case and it's not necessary in this driver,
so we can just delete this code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement mbus_code filtering for format enumeration.
Without this patch libcamera errors out with:
"ERROR V4L2 v4l2_videodevice.cpp:982 /dev/video0[cap]: Media bus code
filtering not supported by the device"
This is the second version of this change which handles the case of
several pixel formats corresponding to one media bus format correctly.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This reverts commit c90f1178dc.
The assumption of "Each entry in formats[] table has unique mbus_code"
is valid for the RDI entities, but not for the PIX ones.
Reverting this patch and creating a new one which handles the PIX entities
correctly results in smaller and more straightforward patch than doing the
changes on top of the current version.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix 4 typos under drivers/media/platform/rockchip/rkisp1/ found by
checkpatch, including the RKISP1_CIF_MI_{M,S}P_PINGPONG_ENABLE macro
definitions.
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VNCSI_IFMD_CSI_CHSEL_MASK is not used: remove it.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 29d7506863 ("media: fsl-viu: allow building it with
COMPILE_TEST") there were several attempts to fix build failures on
PPC, MICROBLAZE and M68K.
However, such errors are still present as reported by kbuild robot.
Fix the problem by using the ioread/write32be() accessors, which build
fine on all platforms.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver always operates on the DMA/IOVA addresses, so calling them
physical addresses is misleading, although when no IOMMU is used they
equal each other. Fix this by renaming all such entries to 'addr' and
adjusting comments.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If an error happens in jpeg_get_drv_data(), i.e. match fails,
jpeg->variant field is NULL, so we cannot access it.
Consider device probe failed if jpeg->variant is NULL.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Baskov Evgeniy <baskov@ispras.ru>
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
when IPI time out, dump VPU status to get more debug information
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
VPU should be in idle state before system is suspended
or it will work abnormally like VPU program counter not
in a correct address or VPU reset
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These 'ops' structs are never modified, so make them const to allow the
compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the CSI-2 firmware parsing code to not use the soon to be
removed v4l2_async_notifier_parse_fwnode_endpoints_by_port() helper. The
change only aims to prepare for the removing of the old helper and there
are no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation of removing the usage of the old helper
v4l2_async_notifier_parse_fwnode_endpoints_by_port() use the
v4l2_async_subdev instead of fwnode_handle to match subdevices.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework the parallel firmware parsing code to not use the soon to be
removed v4l2_async_notifier_parse_fwnode_endpoints_by_port() helper. The
change only aims to prepare for the removing of the old helper and there
are no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation of removing the usage of the old helper
v4l2_async_notifier_parse_fwnode_endpoints_by_port() do not dynamically
allocate the whole structure containing the parameters for the parallel
interface, instead only allocate the v4l2_async_subdev structure. There
is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
in_interrupt() covers hard and soft interrupt servicing and bottom half
disabled contexts, which is semantically undefined and useless.
The comment for __ccdc_lsc_configure() "Context: in_interrupt()" is
therefore as useful as "Context: unknown'. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl/EM9oeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/3kH/RNkFyTlHlUkZpJx
8Ks2yWgUln7YhZcmOaG/IcIyWnhCgo3l35kiaH7XxM+rPMZzidp51MHUllaTAQDc
u+5EFHMJsmTWUfE8ocHPb1cPdYEDSoVr6QUsixbL9+uADpRz+VZVtWMb89EiyMrC
wvLIzpnqY5UNriWWBxD0hrmSsT4g9XCsauer4k2KB+zvebwg6vFOMCFLFc2qz7fb
ABsrPFqLZOMp+16chGxyHP7LJ6ygI/Hwf7tPW8ppv4c+hes4HZg7yqJxXhV02QbJ
s10s6BTcEWMqKg/T6L/VoScsMHWUcNdvrr3uuPQhgup240XdmB1XO8rOKddw27e7
VIjrjNw=
=4ZaP
-----END PGP SIGNATURE-----
Merge tag 'v5.10-rc6' into patchwork
Linux 5.10-rc6
* tag 'v5.10-rc6': (1815 commits)
Linux 5.10-rc6
sock: set sk_err to ee_errno on dequeue from errq
mptcp: fix NULL ptr dereference on bad MPJ
net: openvswitch: fix TTL decrement action netlink message format
perf probe: Change function definition check due to broken DWARF
perf probe: Fix to die_entrypc() returns error correctly
perf stat: Use proper cpu for shadow stats
perf record: Synthesize cgroup events only if needed
perf diff: Fix error return value in __cmd_diff()
perf tools: Update copy of libbpf's hashmap.c
x86/mce: Do not overwrite no_way_out if mce_end() fails
kvm: x86/mmu: Fix get_mmio_spte() on CPUs supporting 5-level PT
KVM: x86: Fix split-irqchip vs interrupt injection window request
KVM: x86: handle !lapic_in_kernel case in kvm_cpu_*_extint
usb: typec: stusb160x: fix power-opmode property with typec-power-opmode
printk: finalize records with trailing newlines
can: af_can: can_rx_unregister(): remove WARN() statement from list operation sanity check
can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0
can: m_can: fix nominal bitiming tseg2 min for version >= 3.1
can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from request_threaded_irq()'s flags
...
The "seg_num," line wasn't indented. All the arguments can fit nicely
on two lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a goto from the middle of the loop, there is no put, thus
causing a memory leak. Hence add a new label that puts the last used
node, and edit the goto statements in the middle of the loop to first go
to the new label.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SDM630/660 SoCs (and variants) have another clock source
for the PHY, which must be set to a rate that's equal or
greater than the CSI PHY timer clock: failing to do this
will produce PHY overflows when trying to get a stream from
a very high bandwidth camera sensor and outputting no frame
or a partial one.
Since I haven't found any usecase in which the csiX_phy
clock needs to be higher than the csiXphy_timer, let's just
set the same rate on both, which seems to work just perfect.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSIPHY on SDM630/660 needs a slightly longer T_HS_CLK_MISS
configuration on lanes CFG4.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the Qualcomm SDM630/636/660 and SDA variants' camera
subsystem. These SoCs are equipped with:
- 3x CSI PHY 3-Phase v1.0 (downstream csiphy-v3.5)
- 4x CSID v5.0
- 2x ISPIF v3.0
- 2x VFE 4.8
As a note, this camera subsystem is very similar to the one that
is found in the MSM8998/APQ8098 SoCs.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the support for VFE 4.8 in the camss-vfe-4-7 driver, as this one
really is a minor revision, requiring the very same management and
basically having the same register layout as VFE 4.7, but needing
a different QoS and DS configuration, using a different register to
enable the wm and habing the same UB size for both instances (instead
of a different size between instance 0 and 1).
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation to add support for VFE 4.8, rename these functions
by adding the vfe version that they are referred to (for example,
vfe_get_ub_size -> vfe47_get_ub_size), as these are the only ones
that will be different for the VFE version 4.8.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Resetting the ISPIF VFE0 context is wrong if we are using the VFE1
for dual-camera or simply because a secondary camera is connected
to it: in this case the reset will always happen on the VFE0 ctx
of the ISPIF, which is .. useless.
Fix this usecase by adding the ISPIF_RST_CMD_1 address and choose
where to do the (or what to) reset based on the VFE line id.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support of BT656 embedded synchronization bus.
This mode allows to save hardware synchro lines hsync & vsync by replacing
them with synchro codes embedded in data stream.
This bus type is only compatible with 8 bits width data bus.
Due to reserved values 0x00 & 0xff used for synchro codes, valid data vary
from 0x1 to 0xfe, this is up to sensor to clip accordingly pixel data. As
a consequence of this clipping, JPEG is not supported with this bus type.
DCMI crop feature is also not available with this bus type.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
of_dma_configure is called by the core before probe gets called so this
is redundant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the MBUS quirks are applied by our global notifier, we can
remove them from our CSI driver for the A31.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the MBUS quirks are applied by our global notifier, we can
remove them from our CSI driver for the A10.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the items in the TODO list were addressed, uapi was reviewed,
documentation written, checkpatch errors fixed, several bugs fixed.
There is no big reason to keep this driver in staging, so move it out.
Dt-bindings Verified with:
make ARCH=arm64 dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/media/rockchip-isp1.yaml
Fields of MAINTAINERS file sorted according to output of
./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS
--order
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[dt-bindings: media: rkisp1: move rockchip-isp1 bindings out of staging]
[hverkuil: fix various checkpatch alignment warnings]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the SMMU translation is disabled in the
arm-smmu shutdown callback during reboot, if
any subsystem are still alive then IOVAs they
are using will become PAs on bus, which may
lead to crash.
So implemented shutdown callback, which detach iommu maps.
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In concurrency usecase and reboot scenario we are seeing muliple
crashes related to iommu_map/iommu_unamp of core->fw.iommu_domain.
In one case we are seeing "Unable to handle kernel NULL pointer
dereference at virtual address 0000000000000008" crash, this is
because of core->fw.iommu_domain in venus_firmware_deinit() and
trying to map in venus_boot() during venus_sys_error_handler()
Call trace:
__iommu_map+0x4c/0x348
iommu_map+0x5c/0x70
venus_boot+0x184/0x230 [venus_core]
venus_sys_error_handler+0xa0/0x14c [venus_core]
process_one_work+0x210/0x3d0
worker_thread+0x248/0x3f4
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
In second case we are seeing "Unable to handle kernel paging request
at virtual address 006b6b6b6b6b6b9b" crash, this is because of
unmapping iommu domain which is already unmapped.
Call trace:
venus_remove+0xf8/0x108 [venus_core]
venus_core_shutdown+0x1c/0x34 [venus_core]
platform_drv_shutdown+0x28/0x34
device_shutdown+0x154/0x1fc
kernel_restart_prepare+0x40/0x4c
kernel_restart+0x1c/0x64
__arm64_sys_reboot+0x190/0x238
el0_svc_common+0xa4/0x154
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x10
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For core ops we are having only write protect but there
is no read protect, because of this in multithreading
and concurrency, one CPU core is reading without wait
which is causing the NULL pointer dereferece crash.
one such scenario is as show below, where in one CPU
core, core->ops becoming NULL and in another CPU core
calling core->ops->session_init().
CPU: core-7:
Call trace:
hfi_session_init+0x180/0x1dc [venus_core]
vdec_queue_setup+0x9c/0x364 [venus_dec]
vb2_core_reqbufs+0x1e4/0x368 [videobuf2_common]
vb2_reqbufs+0x4c/0x64 [videobuf2_v4l2]
v4l2_m2m_reqbufs+0x50/0x84 [v4l2_mem2mem]
v4l2_m2m_ioctl_reqbufs+0x2c/0x38 [v4l2_mem2mem]
v4l_reqbufs+0x4c/0x5c
__video_do_ioctl+0x2b0/0x39c
CPU: core-0:
Call trace:
venus_shutdown+0x98/0xfc [venus_core]
venus_sys_error_handler+0x64/0x148 [venus_core]
process_one_work+0x210/0x3d0
worker_thread+0x248/0x3f4
kthread+0x11c/0x12c
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently in calculate_inst_freq(), video driver is calculating
macro blocks per frame instead of macro blocks per second(mpbs).
Which results frequency is always setting to lower frequency (150MHz)
as per frequency table for sc7180. Hence the playback is not smooth.
Corrected this by correcting the mbps calculation in calculate_inst_freq().
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As per current implementation, video driver is unvoting "videom-mem" path
for last video session during vdec_session_release().
While video playback when we try to suspend device, we see video clock
warnings since votes are already removed during vdec_session_release().
corrected this by putting dummy vote on "video-mem" after last video
session release and unvoting it during suspend.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As per bandwidth table video driver is voting with average bandwidth
for "video-mem" and "cpu-cfg" paths as peak bandwidth is zero
in bandwidth table.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently video driver is voting for venus0-ebi path during buffer
processing with an average bandwidth of all the instances and
unvoting during session release.
While video streaming when we try to do XO-SD using the command
"echo mem > /sys/power/state command" , device is not entering
to suspend state and from interconnect summary seeing votes for venus0-ebi
Corrected this by voting for venus0-ebi path in venus_runtime_resume()
and unvote during venus_runtime_suspend().
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently video driver is voting after clk enable and un voting
before clk disable. This is incorrect, video driver should vote
before clk enable and unvote after clk disable.
Corrected this by changing the order of clk enable and clk disable.
suspend")
Fixes: 07f8f22a33 ("media: venus: core: remove CNOC voting while device
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Per the stateful codec specification, VIDIOC_G_SELECTION with a target
of V4L2_SEL_TGT_COMPOSE is supposed to return the crop area of capture
buffers containing the decoded frame. Until now the driver did not get
that information from the firmware and just returned the dimensions of
CAPTURE buffers.
The firmware unfortunately does not always provide the crop information
from the stream ; also make sure to detect when that happens and
fallback to providing the coded size in these cases.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The default codec after driver open is set to be H264 but the
instance format for capture is wrongly set to H263. Correct this
to H264.
For regular applications this is not a big issue because they set
the format through S_FMT but for example v4l2-compliance does not.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The profile and level in op_set_ctrl was recently changed but during
v4l2_ctrl_handler_setup profile and level control values are mangled.
Fixes: 435c53c369 ("media: venus: venc: Use helper to set profile and level")
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Linus Torvalds
Rafael J. Wysocki
Viresh Kumar
Jacopo Mondi
Neil Armstrong
Ezequiel Garcia
Dan Carpenter
Andrey Konovalov
Peilin Ye
Fabio Estevam
Marek Szyprowski
Baskov Evgeniy
Irui Wang
Rikard Falkeborn
Niklas Söderlund
Thomas Gleixner
Mauro Carvalho Chehab
Nishka Dasgupta
AngeloGioacchino Del Regno
Hugues Fruchet
Maxime Ripard
Helen Koike
Mansur Alisha Shaik
Alexandre Courbot
Stanimir Varbanov