In the device tree for Ebony, the 'ranges' property in the node for
the EBC bridge shows the mappings from the chip select / address lines
actually used for the EBC peripherals into the address space of the
OPB. At present, these mappings are hardcoded in ebony.dts for the
mappings set up by the OpenBIOS firmware when it configures the EBC
bridge.
This replaces the hardcoded mappings with code in the zImage to
read the EBC configuration registers and create an appropriate ranges
property based on them. This should make the zImage and kernel more
robust to changes in firmware configuration. In particular, some of
the Ebony's DIP switches can change the effective address of the Flash
and other peripherals in OPB space. With this patch, the kernel will
be able to cope with at least some of the possible variations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ebony_exit() function which resets the Ebony board should in fact
be common to most if not all 44x boards. This moves the function out
into 44x.c, renaming it, so it can be used by other 44x platforms.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the powerpc kernel has a 64-bit only feature,
COHERENT_ICACHE used for those CPUS which maintain icache/dcache
coherency in hardware (POWER5, essentially). It also has a feature,
SPLIT_ID_CACHE, which is used on CPUs which have separate i and
d-caches, which is to say everything except 601 and Freescale E200.
In nearly all the places we check the SPLIT_ID_CACHE, what we actually
care about is whether the i and d-caches are coherent (which they will
be, trivially, if they're the same cache).
This tries to clarify the situation a little. The COHERENT_ICACHE
feature becomes availble on 32-bit and is set for all CPUs where i and
d-cache are effectively coherent, whether this is due to special logic
(POWER5) or because they're unified. We check this, instead of
SPLIT_ID_CACHE nearly everywhere.
The SPLIT_ID_CACHE feature itself is replaced by a UNIFIED_ID_CACHE
feature with reversed sense, set only on 601 and Freescale E200. In
the two places (one Freescale BookE specific) where we really care
whether it's a unified cache, not whether they're coherent, we check
this feature. The CPUs with unified cache are so few, we could
consider replacing this feature bit with explicit checks against the
PVR.
This will make unifying the 32-bit and 64-bit cache flush code a
little more straightforward.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using typedefs to rename structure types if frowned on by CodingStyle.
However, we do so for the hash PTE structure on both ppc32 (where it's
called "PTE") and ppc64 (where it's called "hpte_t"). On ppc32 we
also have such a typedef for the BATs ("BAT").
This removes this unhelpful use of typedefs, in the process
bringing ppc32 and ppc64 closer together, by using the name "struct
hash_pte" in both cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In arch/powerpc/mm/pgtable_32.c, the variable io_bat_index and the
macro is_power_of_4() no longer have any users. This removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
APUS (the Amiga Power-Up System) is not supported under arch/powerpc
and it's unlikely it ever will be. Therefore, this patch removes the
fragments of APUS support code from arch/powerpc which have been
copied from arch/ppc.
A few APUS references are left in asm-powerpc in .h files which are
still used from arch/ppc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These old-fashioned IO mapping functions no longer have any callers in
code which remains relevant on arch/powerpc. Therefore, this removes
them from arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, all OF-related code in the bootloader is contained in of.c.
of.c also provides the platform specific things necessary to boot on
an OF platform.
However, there are platforms (such as PReP) which can include an OF
implementation, but are not bootable as pure OF systems. For use by
such platforms, this patch splits out the low-level parts of the OF
code (call_prom() and various wrappers thereof) into a new oflib.c
file. In addition, the code related to bootwrapper console output via
OF are moved to a new ofconsole.c file. Both these files are included
in the wrapper.a library where they can be used by both full-OF and
partial OF platforms.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A lot of the options in arch/powerpc/Kconfig deal with the CPU menu,
and my next patches add more to them. Moving them to a new
arch/powerpc/platforms/Kconfig.cputype file makes it easier to
follow.
There are no functional changes in here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.
Killing just one of the process threads can leave the application in a
bad state, whereas killing the entire process group would allow for
the application to restart, or be otherwise handled, and makes it very
obvious that something has gone wrong.
This change allows the entire process group to be taken down, rather than
just the one thread.
lightly tested on powerpc
Signed-off-by: Will <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A Power6 can give up CPU cycles on a dedicated CPU (as opposed to a
shared CPU) to other shared processors if the administrator asks for it
(via the HMC).
This enables that to work properly on P6.
This just involves setting a bit in the CAS structure as well as the
VPA. To donate cycles, a CPU has to have all SMT threads idle and
have the donate bit set in the VPA. Then call H_CEDE.
The reason why shared processors just aren't used is because dedicated
CPUs are guaranteed an actual processor, yet the system is still able to
increase the capacity of the shared CPU pool.
Also rename the VPA's cpuctls_task_attrs field to a more accurate name.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves things around a little bit in the new common signal.c
and signal.h files to remove the last #ifdef in the middle of the
common do_signal().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
set_dabr() and thread.dabr exist on 32 bits as well nowadays (they
actually may do something even, depending on what CPU you have).
So this removes the ifdef.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code for creating signal frames was still duplicated and split
in strange ways between 32 and 64 bits, including the SA_ONSTACK
handling being in do_signal on 32 bits but inside handle_rt_signal
on 64 bits etc...
This moves the 64 bits get_sigframe() to the generic signal.c,
cleans it a bit, moves the access_ok() call done by all callers to
it as well, and adapts/cleanups the 3 different signal handling cases
to use that common function.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc signal code still had some obsolete freezer bits that
have long been removed from x86 (it's now done in generic code).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
do_signal has exactly the same behaviour on 32bit and 64bit and 32bit
compat on 64bit for handling 32bit signals. Consolidate all these
into one common function in signal.c. The only odd left over is
the try_to_free in the 32bit version that no other architecture has
in mainline (only in i386 for some odd SuSE release). We should
probably get rid of it in a separate patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
restore_sigmask is exactly the same on 32 and 64bit, so move it to
common code. Also move _BLOCKABLE to signal.h to avoid defining it
multiple times.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
sys_sigaltstack is the same on 32bit and 64 and we can consolidate it
to signal.c. The only difference is that the 32bit code uses ints
for the unused register paramaters and 64bit unsigned long. I've
changed it to unsigned long because it's the same width on 32bit.
(I also wonder who came up with this awkward calling convention.. :))
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the code in signal_32.c and signal_64.c for handling
syscall restart into a common signal.c file and converge around a single
implementation that is based on the 32 bits one, using trap, ccr
and r3 rather than the special "result" field for deciding what to do.
The "result" field is now pretty much deprecated. We still set it for
the sake of whatever might rely on it in userland but we no longer use
it's content.
This, along with a previous patch that enables ptracers to write to
"trap" and "orig_r3" should allow gdb to properly handle syscall
restarting.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the #ifdef CONFIG_PPC64 around setting the DABR.
The actual setting of the SPR inside of the set_dabr() function is dependent
on CONFIG_PPC64 || CONFIG_6xx but you can always provide a ppc_md hook to
override that. We should improve support for different HW breakpoints
facilities but this is a first step.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow ptrace to set dabr in the thread structure for both 32 and 64 bits,
though only 64 bits actually uses that field, it's actually defined in both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of the gratuitous difference between 32 and 64-bit ptrace is
whether you can whack the MSR:FE0 and FE1 bits from ptrace. This
patch forbids it unconditionally. In addition, the 64-bit kernels
used to return the exception mode in the MSR on reads, but 32-bit
kernels didn't. This patch makes it return those bits on both.
Finally, since ptrace-ppc32.h and ptrace-ppc64.h are mostly empty now, and
since the previous patch made ptrace32.c no longer need the MSR_DEBUGCHANGE
definition, we just remove those 2 files and move back the remaining bits
to ptrace.c (they were short lived heh ?).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch allows a ptracer to write to the "trap" and "orig_r3" words
of the pt_regs.
This, along with a subsequent patch to the signal restart code, should
enable gdb to properly handle syscall restarting after executing a separate
function (at least when there's no restart block).
This patch also removes ptrace32.c code toying directly with the registers
and makes it use the ptrace_get/put_reg() accessors for everything so that
the logic for checking what is permitted is in only one place.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
CHECK_FULL_REGS() exist on both 32 and 64 bits, so there's no need
to make it conditional on CONFIG_PPC32.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This folds back the ptrace-common.h bits back into ptrace.c and removes
that file. The FSL SPE bits from ptrace-ppc32.h are folded back in as
well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc ptrace interface is dodgy at best. We have defined our
"own" versions of GETREGS/SETREGS/GETFPREGS/SETFPREGS that strangely
take arguments in reverse order from other archs (in addition to having
different request numbers) and have subtle issue, like not accessing
all of the registers in their respective categories.
This patch moves the implementation of those to a separate function
in order to facilitate their deprecation in the future, and provides
new ptrace requests that mirror the x86 and sparc ones and use the
same numbers:
PTRACE_GETREGS : returns an entire pt_regs (the whole thing,
not only the 32 GPRs, though that doesn't
include the FPRs etc... There's a compat version
for 32 bits that returns a 32 bits compatible
pt_regs (44 uints)
PTRACE_SETREGS : sets an entire pt_regs (the whole thing,
not only the 32 GPRs, though that doesn't
include the FPRs etc... Some registers cannot be
written to and will just be dropped, this is the
same as with POKEUSR, that is anything above MQ
on 32 bits and CCR on 64 bits. There is a compat
version as well.
PTRACE_GETFPREGS : returns all the FP registers -including- the FPSCR
that is 33 doubles (regardless of 32/64 bits)
PTRACE_SETFPREGS : sets all the FP registers -including- the FPSCR
that is 33 doubles (regardless of 32/64 bits)
And two that only exist on 64 bits kernels:
PTRACE_GETREGS64 : Same as PTRACE_GETREGS, except there is no compat
function, a 32 bits process will obtain the full 64
bits registers
PTRACE_SETREGS64 : Same as PTRACE_SETREGS, except there is no compat
function, a 32 bits process will set the full 64
bits registers
The two later ones makes things easier to have a 32 bits debugger on a
64 bits program (or on a 32 bits program that uses the full 64 bits of
the GPRs, which is possible though has issues that will be fixed in a
later patch).
Finally, while at it, the patch removes a whole bunch of code duplication
between ptrace32.c and ptrace.c, in large part by having the former call
into the later for all requests that don't need any special "compat"
treatment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc ptrace code has some weirdness, like a ptrace-common.h file that
is actually ppc64 only and some of the 32 bits code ifdef'ed inside ptrace.c.
There are also separate implementations for things like get/set_vrregs for
32 and 64 bits which is totally unnecessary.
This patch cleans that up a bit by having a ptrace-common.h which contains
really common code (and makes a lot more code common), and ptrace-ppc32.h and
ptrace-ppc64.h files that contain the few remaining different bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The handling of PPC_PTRACE_GETFPREGS is broken on 32 bits kernel,
it will only return half of the registers. Since that call didn't
initially exist for 32 bits kernel (added recently), rather than
fixing it, let's just remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a "capabilities" file to spu contexts consisting of a
list of linefeed separated capability names. The current exposed
capabilities are "sched" (the context is scheduleable) and
"step" (the context supports single stepping).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for SPU single stepping. The single
step bit is set in the SPU when the current process is
being single-stepped via ptrace. The spu then stops and
returns with a specific flag set and the syscall exit code
will generate the SIGTRAP.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This rewrites pretty much from scratch the handling of MMIO and PIO
space allocations on powerpc64. The main goals are:
- Get rid of imalloc and use more common code where possible
- Simplify the current mess so that PIO space is allocated and
mapped in a single place for PCI bridges
- Handle allocation constraints of PIO for all bridges including
hot plugged ones within the 2GB space reserved for IO ports,
so that devices on hotplugged busses will now work with drivers
that assume IO ports fit in an int.
- Cleanup and separate tracking of the ISA space in the reserved
low 64K of IO space. No ISA -> Nothing mapped there.
I booted a cell blade with IDE on PIO and MMIO and a dual G5 so
far, that's it :-)
With this patch, all allocations are done using the code in
mm/vmalloc.c, though we use the low level __get_vm_area with
explicit start/stop constraints in order to manage separate
areas for vmalloc/vmap, ioremap, and PCI IOs.
This greatly simplifies a lot of things, as you can see in the
diffstat of that patch :-)
A new pair of functions pcibios_map/unmap_io_space() now replace
all of the previous code that used to manipulate PCI IOs space.
The allocation is done at mapping time, which is now called from
scan_phb's, just before the devices are probed (instead of after,
which is by itself a bug fix). The only other caller is the PCI
hotplug code for hot adding PCI-PCI bridges (slots).
imalloc is gone, as is the "sub-allocation" thing, but I do beleive
that hotplug should still work in the sense that the space allocation
is always done by the PHB, but if you unmap a child bus of this PHB
(which seems to be possible), then the code should properly tear
down all the HPTE mappings for that area of the PHB allocated IO space.
I now always reserve the first 64K of IO space for the bridge with
the ISA bus on it. I have moved the code for tracking ISA in a separate
file which should also make it smarter if we ever are capable of
hot unplugging or re-plugging an ISA bridge.
This should have a side effect on platforms like powermac where VGA IOs
will no longer work. This is done on purpose though as they would have
worked semi-randomly before. The idea at this point is to isolate drivers
that might need to access those and fix them by providing a proper
function to obtain an offset to the legacy IOs of a given bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes unmap_vm_area static and a wrapper around a new
exported unmap_kernel_range that takes an explicit range instead
of a vm_area struct.
This makes it more versatile for code that wants to play with kernel
page tables outside of the standard vmalloc area.
(One example is some rework of the PowerPC PCI IO space mapping
code that depends on that patch and removes some code duplication
and horrible abuse of forged struct vm_struct).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Twiddle the copyright notices. Per current guidelines, the use
of the (C) or (c) in source code is deprecated.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 6 +++++-
arch/powerpc/platforms/pseries/eeh_cache.c | 3 ++-
arch/powerpc/platforms/pseries/eeh_driver.c | 6 +++---
3 files changed, 10 insertions(+), 5 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Track and report the number of times we read an all-1s value (0xff,
0xffff or 0xffffffff) from each device which is valid data, not
indicating EEH isolation.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 5 +++++
arch/powerpc/platforms/pseries/eeh_sysfs.c | 3 +++
include/asm-powerpc/pci-bridge.h | 1 +
3 files changed, 9 insertions(+)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maybe the type should have been char[] instead of __u8[]
in the first place, but this will do.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously, registering this early console would just result
in dropping early buffered printk output until a udbg_putc
was registered.
However, commit 69331af79c
clears the CON_PRINTBUFFER flag on the main console when a
CON_BOOT (early) console has been registered, resulting in
the buffered messages never being displayed to the user.
This fixes the problem by making sure we don't register udbg_console
on platforms that don't implement udbg_putc.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The per-cpu area(a) for the secondary CPU(s) isn't getting allocated
on old SMP powermacs that don't have the secondary CPU(s) listed in
the device tree, as per-cpu areas are now only allocated for CPUs in
the cpu_possible_map, and we aren't setting the bits for the secondary
CPU(s) until smp_prepare_cpus(), which is after per-cpu allocation.
Therefore this sets the bits for CPUs 1..3 in cpu_possible_map in
pmac_setup_arch, so they get per-cpu data allocated.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix smp barriers in test_and_{change,clear,set}_bit
[MIPS] Fix IP27 build
[MIPS] Fix modpost warnings by making start_secondary __cpuinit
[MIPS] SMTC: Fix build error caused by nonsense code.
[MIPS] SMTC: The MT ASE requires to initialize c0_pagemask and c0_wired.
[MIPS] SMTC: Don't continue in set_vi_srs_handler on detected bad arguments.
[MIPS] SMTC: Fix warning.
[MIPS] Wire up utimensat, signalfd, timerfd, eventfd
[MIPS] Atlas: Fix build.
[MIPS] Always install the DSP exception handler.
[MIPS] SMTC: Don't set and restore irqregs ptr from self_ipi.
[MIPS] Fix KMODE for the R3000
Some non-DSP enabled cores 24K / 34K can generate a DSP exception where they
are actually expected to produce a reserved instruction exception.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Gibson
Arnd Bergmann
will schmidt
Jake Moilanen
Benjamin Herrenschmidt
Christoph Hellwig
Linas Vepstas
Jon Tollefson
Segher Boessenkool
Milton Miller
Paul Mackerras
Linus Torvalds
Atsushi Nemoto
Ralf Baechle
Chris Dearman