Partition boundary calculation fails for DASD FBA disks under the
following conditions:
- disk is formatted with CMS FORMAT with a blocksize of more than
512 bytes
- all of the disk is reserved to a single CMS file using CMS RESERVE
- the disk is accessed using the DIAG mode of the DASD driver
Under these circumstances, the partition detection code tries to
read the CMS label block containing partition-relevant information
from logical block offset 1, while it is in fact located at physical
block offset 1.
Fix this problem by using the correct CMS label block location
depending on the device type as determined by the DASD SENSE ID
information.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the following changes to partition check code.
* Add ->bdev to struct parsed_partitions.
* Introduce read_part_sector() which is a simple wrapper around
read_dev_sector() which takes struct parsed_partitions *state
instead of @bdev.
* For functions which used to take @state and @bdev, drop @bdev. For
functions which used to take @bdev, replace it with @state.
* While updating, drop superflous checks on NULL state/bdev in ldm.c.
This cleans up the API a bit and enables better handling of IO errors
during partition check as the generic partition check code now has
much better visibility into what went wrong in the low level code
paths.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The dasd device driver will now support ECKD devices with more then
65520 cylinders.
In the traditional ECKD adressing scheme each track is addressed
by a 16-bit cylinder and 16-bit head number. The new addressing
scheme makes use of the fact that the actual number of heads is
never larger then 15, so 12 bits of the head number can be redefined
to be part of the cylinder address.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CDL formated DASDs are now detected correctly even if no VOL1 label is
on the disk. This prevents possible loss of data.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
check_partition() stops its probe once it hits an I/O error from the
partition checkers. This would prevent the actual partition checker
getting a chance to verify the partition.
So this patch lets check_partition() continue probing untill it hits a
success while recording the I/O error which might have been reported by the
checking routines.
Also, it does some cleanup of the partition methods for ibm, atari and
amiga to return -1 upon hitting an I/O error.
Signed-off-by: Suzuki K P <suzuki@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DASD allows to open a device as soon as gendisk is registered, which means the
device is a fake device (capacity=0) and we do know nothing about blocksize
and partitions at that point of time. In case the device is opened by
someone, the bdev and inode creation is done with the fake device info and the
following partition detection code is just using the wrong data.
To avoid this modify the DASD state machine to make sure that the open is
rejected until the device analysis is either finished or an unformatted device
was detected.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Moved definition of CMS volume label to vtoc.h and modify partitions/ibm.c to
use this volume label definition instead of anonymous array.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Peter Oberparleiter
Tejun Heo
Martin K. Petersen
Stefan Weinhuber
Stefan Haberland
Suzuki K P
Jörn Engel
Horst Hummel
Linus Torvalds