[ Upstream commit cf3128a7ac ]
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17955aba78 ]
There is error message when defer probe happens:
fsl-micfil-dai 30ca0000.micfil: Unbalanced pm_runtime_enable!
Fix the error handler with pm_runtime_enable and add
fsl_micfil_remove() for pm_runtime_disable.
Fixes: 47a70e6fc9 ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683540996-6136-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9d9ce5462 ]
These offsets do not fall under the MDP TOP block and do not fit the
comment right above. Move them to dpu_hw_interrupts.c next to the
repsective MDP_INTF_x_OFF interrupt block offsets.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/534203/
Link: https://lore.kernel.org/r/20230411-dpu-intf-te-v4-3-27ce1a5ab5c6@somainline.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 148e852f29 ]
SC8180x has the eDP controller wired up to INTF_5, so add the interrupt
register block for this interface to the list.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220215043353.1256754-1-bjorn.andersson@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: e9d9ce5462 ("drm/msm/dpu: Move non-MDP_TOP INTF_INTR offsets out of hwio header")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85c636284c ]
while binding the code always registers a audio driver, however there
is no corresponding unregistration done in unbind. This leads to multiple
redundant audio platform devices if dp_display_bind and dp_display_unbind
happens multiple times during startup. On X13s platform this resulted in
6 to 9 audio codec device instead of just 3 codec devices for 3 dp ports.
Fix this by unregistering codecs on unbind.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: d13e36d7d2 ("drm/msm/dp: add audio support for Display Port on MSM")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/533324/
Link: https://lore.kernel.org/r/20230421145657.12186-1-srinivas.kandagatla@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fc46f9421 ]
This reverts commit b0355dbbf1.
The reverted commit clears the secpath on packets received via xfrm interfaces
to support nested IPsec tunnels. This breaks Netfilter policy matching using
xt_policy in the FORWARD chain, as the secpath is missing during forwarding.
Additionally, Benedict Wong reports that it breaks Transport-in-Tunnel mode.
Fix this regression by reverting the commit until we have a better approach
for nested IPsec tunnels.
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Link: https://lore.kernel.org/netdev/20230412085615.124791-1-martin@strongswan.org/
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 430cac4874 ]
The current code doesn't let a simple "allow" policy counteract a
default policy blocking all incoming packets:
ip x p setdefault in block
ip x p a src 192.168.2.1/32 dst 192.168.2.2/32 dir in action allow
At this stage, we have an allow policy (with or without transforms)
for this packet. It doesn't matter what the default policy says, since
the policy we looked up lets the packet through. The case of a
blocking policy is already handled separately, so we can remove this
check.
Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e9b8992b1 ]
The purpose of this patch is to provide a central location where all
HP related drivers are found. HP drivers will recide under
drivers/platform/x86/hp directory.
Introduce changes to Kconfig file to list all HP driver under "HP X86
Platform Specific Device Drivers" menu option. Additional changes
include update MAINTAINERS file to indicate hp related drivers new
path.
Signed-off-by: Jorge Lopez <jorge.lopez2@hp.com>
Link: https://lore.kernel.org/r/20221020201033.12790-2-jorge.lopez2@hp.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: decab2825c ("platform/x86: hp-wmi: add micmute to hp_wmi_keymap struct")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 401199ffa9 ]
Add scancodes reported by the touchpad on/off button. The actual disabling
and enabling is done in hardware, and this just reports that change to
userspace.
Signed-off-by: Daniel Houldsworth <dhould3@gmail.com>
Link: https://lore.kernel.org/r/20220922115459.6511-1-dhould3@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: decab2825c ("platform/x86: hp-wmi: add micmute to hp_wmi_keymap struct")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 829632dae8 ]
The panic notifiers' callbacks execute in an atomic context, with
interrupts/preemption disabled, and all CPUs not running the panic
function are off, so it's very dangerous to wait on a regular
spinlock, there's a risk of deadlock.
Refactor the panic notifier of parisc/power driver to make use
of spin_trylock - for that, we've added a second version of the
soft-power function. Also, some comments were reorganized and
trailing white spaces, useless header inclusion and blank lines
were removed.
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Jeroen Roovers <jer@xs4all.nl>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96da8f1483 ]
When dln2_setup_rx_urbs() in dln2_probe() fails, error out_free forgets
to call usb_put_dev() to decrease the refcount of dln2->usb_dev.
Fix this by adding usb_put_dev() in the error handling code of
dln2_probe().
Signed-off-by: Qiang Ning <qning0106@126.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230330024353.4503-1-qning0106@126.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2367e0ecb4 ]
There are two issues related to the number of ports coming from
Devicetree when exceeding in total QCOM_SDW_MAX_PORTS. Both lead to
incorrect memory accesses:
1. With DTS having too big value of input or output ports, the driver,
when copying port parameters from local/stack arrays into 'pconfig'
array in 'struct qcom_swrm_ctrl', will iterate over their sizes.
2. If DTS also has too many parameters for these ports (e.g.
qcom,ports-sinterval-low), the driver will overflow buffers on the
stack when reading these properties from DTS.
Add a sanity check so incorrect DTS will not cause kernel memory
corruption.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230222144412.237832-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9b2e603c6 ]
Wired GIP devices present multiple interfaces with the same USB identification
other than the interface number. This adds constants for differentiating two of
them and uses them where appropriate
Signed-off-by: Vicki Pfau <vi@endrift.com>
Link: https://lore.kernel.org/r/20230411031650.960322-2-vi@endrift.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9afea57384 ]
When attaching to a domain, the driver would alloc a DMA buffer which
is used to store address mapping table, and it need to be released
when the IOMMU domain is freed.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20230331033124.864691-2-zhang.lyra@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67ea0b7ce4 ]
When an overflow occurs in the PRI queue, the SMMU toggles the overflow
flag in the PROD register. To exit the overflow condition, the PRI thread
is supposed to acknowledge it by toggling this flag in the CONS register.
Unacknowledged overflow causes the queue to stop adding anything new.
Currently, the priq thread always writes the CONS register back to the
SMMU after clearing the queue.
The writeback is not necessary if the OVFLG in the PROD register has not
been changed, no overflow has occured.
This commit checks the difference of the overflow flag between CONS and
PROD register. If it's different, toggles the OVACKFLG flag in the CONS
register and write it to the SMMU.
The situation is similar for the event queue.
The acknowledge register is also toggled after clearing the event
queue but never propagated to the hardware. This would only be done the
next time when executing evtq thread.
Unacknowledged event queue overflow doesn't affect the event
queue, because the SMMU still adds elements to that queue when the
overflow condition is active.
But it feel nicer to keep SMMU in sync when possible, so use the same
way here as well.
Signed-off-by: Tomas Krcka <krckatom@amazon.de>
Link: https://lore.kernel.org/r/20230329123420.34641-1-tomas.krcka@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4a2adbf35 ]
Older gcc versions get confused by comparing a u32 value to a negative
constant in a switch()/case block:
drivers/clk/tegra/clk-tegra20.c: In function 'tegra20_clk_measure_input_freq':
drivers/clk/tegra/clk-tegra20.c:581:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_12MHZ:
^~~~
drivers/clk/tegra/clk-tegra20.c:593:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_26MHZ:
Make the constants unsigned instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230227085914.2560984-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec275bf969 ]
In a previous commit c1006bd13146, ni->mi.mrec in ni_write_inode()
could be NULL, and thus a NULL check is added for this variable.
However, in the same call stack, ni->mi.mrec can be also dereferenced
in ni_clear():
ntfs_evict_inode(inode)
ni_write_inode(inode, ...)
ni = ntfs_i(inode);
is_rec_inuse(ni->mi.mrec) -> Add a NULL check by previous commit
ni_clear(ntfs_i(inode))
is_rec_inuse(ni->mi.mrec) -> No check
Thus, a possible null-pointer dereference may exist in ni_clear().
To fix it, a NULL check is added in this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dae4f6341 ]
Syzbot reports a NULL dereference in ni_write_inode.
When creating a new inode, if allocation fails in mi_init function
(called in mi_format_new function), mi->mrec is set to NULL.
In the error path of this inode creation, mi->mrec is later
dereferenced in ni_write_inode.
Add a NULL check to prevent NULL dereference.
Link: https://syzkaller.appspot.com/bug?extid=f45957555ed4a808cc7a
Reported-and-tested-by: syzbot+f45957555ed4a808cc7a@syzkaller.appspotmail.com
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1226113473 ]
Some platforms support more than 128 stream matching groups than what is
defined by the ARM SMMU architecture specification. But due to some unknown
reasons, those additional groups don't exhibit the same behavior as the
architecture supported ones.
For instance, the additional groups will not detect the quirky behavior of
some firmware versions intercepting writes to S2CR register, thus skipping
the quirk implemented in the driver and causing boot crash.
So let's limit the groups to 128 for now until the issue with those groups
are fixed and issue a notice to users in that case.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230327080029.11584-1-manivannan.sadhasivam@linaro.org
[will: Reworded the comment slightly]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa4d540b41 ]
GCC-13 (and Clang)[1] does not like to access a partially allocated
object, since it cannot reason about it for bounds checking.
In this case 140 bytes are allocated for an object of type struct
ib_umad_packet:
packet = kzalloc(sizeof(*packet) + IB_MGMT_RMPP_HDR, GFP_KERNEL);
However, notice that sizeof(*packet) is only 104 bytes:
struct ib_umad_packet {
struct ib_mad_send_buf * msg; /* 0 8 */
struct ib_mad_recv_wc * recv_wc; /* 8 8 */
struct list_head list; /* 16 16 */
int length; /* 32 4 */
/* XXX 4 bytes hole, try to pack */
struct ib_user_mad mad __attribute__((__aligned__(8))); /* 40 64 */
/* size: 104, cachelines: 2, members: 5 */
/* sum members: 100, holes: 1, sum holes: 4 */
/* forced alignments: 1, forced holes: 1, sum forced holes: 4 */
/* last cacheline: 40 bytes */
} __attribute__((__aligned__(8)));
and 36 bytes extra bytes are allocated for a flexible-array member in
struct ib_user_mad:
include/rdma/ib_mad.h:
120 enum {
...
123 IB_MGMT_RMPP_HDR = 36,
... }
struct ib_user_mad {
struct ib_user_mad_hdr hdr; /* 0 64 */
/* --- cacheline 1 boundary (64 bytes) --- */
__u64 data[] __attribute__((__aligned__(8))); /* 64 0 */
/* size: 64, cachelines: 1, members: 2 */
/* forced alignments: 1 */
} __attribute__((__aligned__(8)));
So we have sizeof(*packet) + IB_MGMT_RMPP_HDR == 140 bytes
Then the address of the flex-array member (for which only 36 bytes were
allocated) is casted and copied into a pointer to struct ib_rmpp_mad,
which, in turn, is of size 256 bytes:
rmpp_mad = (struct ib_rmpp_mad *) packet->mad.data;
struct ib_rmpp_mad {
struct ib_mad_hdr mad_hdr; /* 0 24 */
struct ib_rmpp_hdr rmpp_hdr; /* 24 12 */
u8 data[220]; /* 36 220 */
/* size: 256, cachelines: 4, members: 3 */
};
The thing is that those 36 bytes allocated for flex-array member data
in struct ib_user_mad onlly account for the size of both struct ib_mad_hdr
and struct ib_rmpp_hdr, but nothing is left for array u8 data[220].
So, the compiler is legitimately complaining about accessing an object
for which not enough memory was allocated.
Apparently, the only members of struct ib_rmpp_mad that are relevant
(that are actually being used) in function ib_umad_write() are mad_hdr
and rmpp_hdr. So, instead of casting packet->mad.data to
(struct ib_rmpp_mad *) create a new structure
struct ib_rmpp_mad_hdr {
struct ib_mad_hdr mad_hdr;
struct ib_rmpp_hdr rmpp_hdr;
} __packed;
and cast packet->mad.data to (struct ib_rmpp_mad_hdr *).
Notice that
IB_MGMT_RMPP_HDR == sizeof(struct ib_rmpp_mad_hdr) == 36 bytes
Refactor the rest of the code, accordingly.
Fix the following warnings seen under GCC-13 and -Warray-bounds:
drivers/infiniband/core/user_mad.c:564:50: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
drivers/infiniband/core/user_mad.c:566:42: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
drivers/infiniband/core/user_mad.c:618:25: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
drivers/infiniband/core/user_mad.c:622:44: warning: array subscript ‘struct ib_rmpp_mad[0]’ is partly outside array bounds of ‘unsigned char[140]’ [-Warray-bounds=]
Link: https://github.com/KSPP/linux/issues/273
Link: https://godbolt.org/z/oYWaGM4Yb [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/ZBpB91qQcB10m3Fw@work
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0b081d17a ]
With KCSAN enabled, end_of_stack() can get out-of-lined. Force it
inline.
Fixes the following warnings:
vmlinux.o: warning: objtool: check_stackleak_irqoff+0x2b: call to end_of_stack() leaves .noinstr.text section
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/cc1b4d73d3a428a00d206242a68fdf99a934ca7b.1681320026.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9be24faadd ]
mcb-pci requests a fixed-size memory region to parse the chameleon
table, however, if the chameleon table is smaller that the allocated
region, it could overlap with the IP Cores' memory regions.
After parsing the chameleon table, drop/reallocate the memory region
with the actual chameleon table size.
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Javier Rodriguez <josejavier.rodriguez@duagon.com>
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Link: https://lore.kernel.org/r/20230411083329.4506-3-jth@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04e82793f0 ]
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Unhandled fault: imprecise external abort (0x1406)
Internal error: : 1406 [#1] SMP ARM
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230418101407.12403-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dac3b19210 ]
PD3.0 Spec 6.4.4.3.2 say that only Responder supports 12 or more SVIDs,
the Discover SVIDs Command Shall be executed multiple times until a
Discover SVIDs VDO is returned ending either with a SVID value of
0x0000 in the last part of the last VDO or with a VDO containing two
SVIDs with values of 0x0000.
In the current implementation, if the last VDO does not find that the
Discover SVIDs Command would be executed multiple times even if the
Responder SVIDs are less than 12, and we found some odd dockers just
meet this case. So fix it.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Link: https://lore.kernel.org/r/20230316081149.24519-1-frank.wang@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bea407a427 ]
Some devices will include battery status usages in the HID descriptor
but we won't see that battery data for one reason or another. For example,
AES sensors won't send battery data unless an AES pen is in proximity.
If a user does not have an AES pen but instead only interacts with the
AES touchscreen with their fingers then there is no need for us to create
a battery object. Similarly, if a family of peripherals shares the same
HID descriptor between wired-only and wireless-capable SKUs, users of the
former may never see a battery event and will not want a power_supply
object created.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217062
Link: https://gitlab.gnome.org/GNOME/gnome-control-center/-/issues/2354
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c614175b ]
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20230318222132.3373-1-kgroeneveld@lenbrook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b3691d15e ]
Now that USB HID++ devices can gather a serial number that matches the
one that would be gathered when connected through a Unifying receiver,
remove the last difference by dropping the product ID as devices
usually have different product IDs when connected through USB or
Unifying.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying before patch: 4067-e8-ce-cd-45
- USB before patch: c086-e8-ce-cd-45
- Unifying and USB after patch: e8-ce-cd-45
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230302130117.3975-2-hadess@hadess.net
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ad1fe0da0 ]
For devices that support the 0x0003 feature (Device Information) version 4,
set the serial based on the output of that feature, rather than relying
on the usbhid code setting the USB serial.
This should allow the serial when connected through USB to (nearly)
match the one when connected through a unifying receiver.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying: 4067-e8-ce-cd-45
- USB before patch: 017C385C3837
- USB after patch: c086-e8-ce-cd-45
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230302130117.3975-1-hadess@hadess.net
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d218c3642 ]
On some devices the BCM Bluetooth adapter does not have a valid bdaddr set.
btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is
the case. But this requires users to manual setup a btaddr, by doing e.g.:
btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3'
Which means that Bluetooth will not work out of the box on such devices.
To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY
which tries to get the bdaddr from devicetree.
But this only works on devicetree platforms. On UEFI based platforms
there is a special Broadcom UEFI variable which when present contains
the devices bdaddr, just like how there is another UEFI variable which
contains wifi nvram contents including the wifi MAC address.
Add support for getting the bdaddr from this Broadcom UEFI variable,
so that Bluetooth will work OOTB for users on devices where this
UEFI variable is present.
This fixes Bluetooth not working on for example Asus T100HA 2-in-1s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77f542b10c ]
Basically all Intel controllers support both Central/Peripheral
LE states.
This patch enables the LE States quirk by default on all
Solar and Magnertor Intel controllers.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3478c68f6 ]
In ip_vs_sync_conn_v0() copy is made to struct ip_vs_sync_conn_options.
That structure looks like this:
struct ip_vs_sync_conn_options {
struct ip_vs_seq in_seq;
struct ip_vs_seq out_seq;
};
The source of the copy is the in_seq field of struct ip_vs_conn. Whose
type is struct ip_vs_seq. Thus we can see that the source - is not as
wide as the amount of data copied, which is the width of struct
ip_vs_sync_conn_option.
The copy is safe because the next field in is another struct ip_vs_seq.
Make use of struct_group() to annotate this.
Flagged by gcc-13 as:
In file included from ./include/linux/string.h:254,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/cpuid.h:62,
from ./arch/x86/include/asm/processor.h:19,
from ./arch/x86/include/asm/timex.h:5,
from ./include/linux/timex.h:67,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from ./include/linux/stat.h:19,
from ./include/linux/module.h:13,
from net/netfilter/ipvs/ip_vs_sync.c:38:
In function 'fortify_memcpy_chk',
inlined from 'ip_vs_sync_conn_v0' at net/netfilter/ipvs/ip_vs_sync.c:606:3:
./include/linux/fortify-string.h:529:25: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
529 | __read_overflow2_field(q_size_field, size);
|
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55793ea54d ]
We tested and found an alarm caused by nbd_ioctl arg without verification.
The UBSAN warning calltrace like below:
UBSAN: Undefined behaviour in fs/buffer.c:1709:35
signed integer overflow:
-9223372036854775808 - 1 cannot be represented in type 'long long int'
CPU: 3 PID: 2523 Comm: syz-executor.0 Not tainted 4.19.90 #1
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x3f0 arch/arm64/kernel/time.c:78
show_stack+0x28/0x38 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x170/0x1dc lib/dump_stack.c:118
ubsan_epilogue+0x18/0xb4 lib/ubsan.c:161
handle_overflow+0x188/0x1dc lib/ubsan.c:192
__ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:206
__block_write_full_page+0x94c/0xa20 fs/buffer.c:1709
block_write_full_page+0x1f0/0x280 fs/buffer.c:2934
blkdev_writepage+0x34/0x40 fs/block_dev.c:607
__writepage+0x68/0xe8 mm/page-writeback.c:2305
write_cache_pages+0x44c/0xc70 mm/page-writeback.c:2240
generic_writepages+0xdc/0x148 mm/page-writeback.c:2329
blkdev_writepages+0x2c/0x38 fs/block_dev.c:2114
do_writepages+0xd4/0x250 mm/page-writeback.c:2344
The reason for triggering this warning is __block_write_full_page()
-> i_size_read(inode) - 1 overflow.
inode->i_size is assigned in __nbd_ioctl() -> nbd_set_size() -> bytesize.
We think it is necessary to limit the size of arg to prevent errors.
Moreover, __nbd_ioctl() -> nbd_add_socket(), arg will be cast to int.
Assuming the value of arg is 0x80000000000000001) (on a 64-bit machine),
it will become 1 after the coercion, which will return unexpected results.
Fix it by adding checks to prevent passing in too large numbers.
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20230206145805.2645671-1-zhongjinghua@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9fff67d2d ]
While running traffics for a long time, randomly an RX descriptor
filled with value "0" from REO destination ring is received.
This descriptor which is invalid causes the wrong SKB (SKB stored in
the IDR lookup with buffer id "0") to be fetched which in turn
causes SKB memory corruption issue and the same leads to crash
after some time.
Changed the start id for idr allocation to "1" and the buffer id "0"
is reserved for error validation. Introduced Sanity check to validate
the descriptor, before processing the SKB.
Crash Signature :
Unable to handle kernel paging request at virtual address 3f004900
PC points to "b15_dma_inv_range+0x30/0x50"
LR points to "dma_cache_maint_page+0x8c/0x128".
The Backtrace obtained is as follows:
[<8031716c>] (b15_dma_inv_range) from [<80313a4c>] (dma_cache_maint_page+0x8c/0x128)
[<80313a4c>] (dma_cache_maint_page) from [<80313b90>] (__dma_page_dev_to_cpu+0x28/0xcc)
[<80313b90>] (__dma_page_dev_to_cpu) from [<7fb5dd68>] (ath11k_dp_process_rx+0x1e8/0x4a4 [ath11k])
[<7fb5dd68>] (ath11k_dp_process_rx [ath11k]) from [<7fb53c20>] (ath11k_dp_service_srng+0xb0/0x2ac [ath11k])
[<7fb53c20>] (ath11k_dp_service_srng [ath11k]) from [<7f67bba4>] (ath11k_pci_ext_grp_napi_poll+0x1c/0x78 [ath11k_pci])
[<7f67bba4>] (ath11k_pci_ext_grp_napi_poll [ath11k_pci]) from [<807d5cf4>] (__napi_poll+0x28/0xb8)
[<807d5cf4>] (__napi_poll) from [<807d5f28>] (net_rx_action+0xf0/0x280)
[<807d5f28>] (net_rx_action) from [<80302148>] (__do_softirq+0xd0/0x280)
[<80302148>] (__do_softirq) from [<80320408>] (irq_exit+0x74/0xd4)
[<80320408>] (irq_exit) from [<803638a4>] (__handle_domain_irq+0x90/0xb4)
[<803638a4>] (__handle_domain_irq) from [<805bedec>] (gic_handle_irq+0x58/0x90)
[<805bedec>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403191533.28114-1-quic_nmaran@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef16799640 ]
A received TKIP key may be up to 32 bytes because it may contain
MIC rx/tx keys too. These are not used by iwl and copying these
over overflows the iwl_keyinfo.key field.
Add a check to not copy more data to iwl_keyinfo.key then will fit.
This fixes backtraces like this one:
memcpy: detected field-spanning write (size 32) of single field "sta_cmd.key.key" at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 (size 16)
WARNING: CPU: 1 PID: 946 at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Hardware name: Dell Inc. Latitude E6430/0H3MT5, BIOS A21 05/08/2017
RIP: 0010:iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Call Trace:
<TASK>
iwl_set_dynamic_key+0x1f0/0x220 [iwldvm]
iwlagn_mac_set_key+0x1e4/0x280 [iwldvm]
drv_set_key+0xa4/0x1b0 [mac80211]
ieee80211_key_enable_hw_accel+0xa8/0x2d0 [mac80211]
ieee80211_key_replace+0x22d/0x8e0 [mac80211]
<snip>
Link: https://www.alionet.org/index.php?topic=1469.0
Link: https://lore.kernel.org/linux-wireless/20230218191056.never.374-kees@kernel.org/
Link: https://lore.kernel.org/linux-wireless/68760035-7f75-1b23-e355-bfb758a87d83@redhat.com/
Cc: Kees Cook <keescook@chromium.org>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58d1b71787 ]
An integer overflow occurs in the iwl_write_to_user_buf() function,
which is called by the iwl_dbgfs_monitor_data_read() function.
static bool iwl_write_to_user_buf(char __user *user_buf, ssize_t count,
void *buf, ssize_t *size,
ssize_t *bytes_copied)
{
int buf_size_left = count - *bytes_copied;
buf_size_left = buf_size_left - (buf_size_left % sizeof(u32));
if (*size > buf_size_left)
*size = buf_size_left;
If the user passes a SIZE_MAX value to the "ssize_t count" parameter,
the ssize_t count parameter is assigned to "int buf_size_left".
Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a
negative number, so "*size" is assigned "buf_size_left" and goes into
the third argument of the copy_to_user function, causing a heap overflow.
This is not a security vulnerability because iwl_dbgfs_monitor_data_read()
is a debugfs operation with 0400 privileges.
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.2d80ace81532.Iecfba549e0e0be21bbb0324675392e42e75bd5ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b655b9a9f8 ]
It is possible that iwl_pci_probe() will fail and free the trans,
then afterwards iwl_pci_remove() will be called and crash by trying
to access trans which is already freed, fix it.
iwlwifi 0000:01:00.0: Detected crf-id 0xa5a5a5a2, cnv-id 0xa5a5a5a2
wfpm id 0xa5a5a5a2
iwlwifi 0000:01:00.0: Can't find a correct rfid for crf id 0x5a2
...
BUG: kernel NULL pointer dereference, address: 0000000000000028
...
RIP: 0010:iwl_pci_remove+0x12/0x30 [iwlwifi]
pci_device_remove+0x3e/0xb0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x4c/0x90
bus_remove_driver+0x5c/0xd0
driver_unregister+0x31/0x50
pci_unregister_driver+0x40/0x90
iwl_pci_unregister_driver+0x15/0x20 [iwlwifi]
__exit_compat+0x9/0x98 [iwlwifi]
__x64_sys_delete_module+0x147/0x260
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.082f6e21341b.I0db21d7fa9a828d571ca886713bd0b5d0b6e1e5c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c11bd04648 ]
The recursion check in __bpf_prog_enter* and __bpf_prog_exit*
leave preempt_count_{sub,add} unprotected. When attaching trampoline to
them we get panic as follows,
[ 867.843050] BUG: TASK stack guard page was hit at 0000000009d325cf (stack is 0000000046a46a15..00000000537e7b28)
[ 867.843064] stack guard page: 0000 [#1] PREEMPT SMP NOPTI
[ 867.843067] CPU: 8 PID: 11009 Comm: trace Kdump: loaded Not tainted 6.2.0+ #4
[ 867.843100] Call Trace:
[ 867.843101] <TASK>
[ 867.843104] asm_exc_int3+0x3a/0x40
[ 867.843108] RIP: 0010:preempt_count_sub+0x1/0xa0
[ 867.843135] __bpf_prog_enter_recur+0x17/0x90
[ 867.843148] bpf_trampoline_6442468108_0+0x2e/0x1000
[ 867.843154] ? preempt_count_sub+0x1/0xa0
[ 867.843157] preempt_count_sub+0x5/0xa0
[ 867.843159] ? migrate_enable+0xac/0xf0
[ 867.843164] __bpf_prog_exit_recur+0x2d/0x40
[ 867.843168] bpf_trampoline_6442468108_0+0x55/0x1000
...
[ 867.843788] preempt_count_sub+0x5/0xa0
[ 867.843793] ? migrate_enable+0xac/0xf0
[ 867.843829] __bpf_prog_exit_recur+0x2d/0x40
[ 867.843837] BUG: IRQ stack guard page was hit at 0000000099bd8228 (stack is 00000000b23e2bc4..000000006d95af35)
[ 867.843841] BUG: IRQ stack guard page was hit at 000000005ae07924 (stack is 00000000ffd69623..0000000014eb594c)
[ 867.843843] BUG: IRQ stack guard page was hit at 00000000028320f0 (stack is 00000000034b6438..0000000078d1bcec)
[ 867.843842] bpf_trampoline_6442468108_0+0x55/0x1000
...
That is because in __bpf_prog_exit_recur, the preempt_count_{sub,add} are
called after prog->active is decreased.
Fixing this by adding these two functions into btf ids deny list.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Yafang <laoar.shao@gmail.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Hao Luo <haoluo@google.com>
Link: https://lore.kernel.org/r/20230413025248.79764-1-laoar.shao@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tobias Brunner
Wyes Karny
Shengjiu Wang
Jianhua Lu
Marijn Suijten
Bjorn Andersson
Srinivas Kandagatla
Martin Willi
Sabrina Dubroca
Fae
Jorge Lopez
Daniel Houldsworth
Guilherme G. Piccoli
Qiang Ning
Krzysztof Kozlowski
Alain Volmat
Vicki Pfau
Chunyan Zhang
Tomas Krcka
Arnd Bergmann
Jia-Ju Bai
Edward Lo
Abdun Nihaal
Ye Bin
Manivannan Sadhasivam
Gustavo A. R. Silva
Hao Zeng
Josh Poimboeuf
Rodríguez Barbarin, José Javier
Tony Lindgren
Frank Wang
Jason Gerecke
Kevin Groeneveld
Bastien Nocera
Philipp Hortmann
Min Li
Hans de Goede
Chethan T N
Simon Horman
Zhong Jinghua
Nagarajan Maran
Chaitanya Kulkarni
Hyunwoo Kim
Daniel Gabay
Yafang