The patch adds support for thread creation and context switching. The
context switching CPU specific code is introduced with the CPU support
patch (part of the arch/arm64/mm/proc.S file). AArch64 supports
ASID-tagged TLBs and the ASID can be either 8 or 16-bit wide (detectable
via the ID_AA64AFR0_EL1 register).
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the handling of the MMU faults (exception
entry code introduced by a previous patch) and page table management.
The user translation table is pointed to by TTBR0 and the kernel one
(swapper_pg_dir) by TTBR1. There is no translation information shared or
address space overlapping between user and kernel page tables.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This patch contains the initialisation of the memory blocks, MMU
attributes and the memory map. Only five memory types are defined:
Device nGnRnE (equivalent to Strongly Ordered), Device nGnRE (classic
Device memory), Device GRE, Normal Non-cacheable and Normal Cacheable.
Cache policies are supported via the memory attributes register
(MAIR_EL1) and only affect the Normal Cacheable mappings.
This patch also adds the SPARSEMEM_VMEMMAP initialisation.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The virtual memory layout is described in
Documentation/arm64/memory.txt. This patch adds the MMU definitions for
the 4KB and 64KB translation table configurations. The SECTION_SIZE is
2MB with 4KB page and 512MB with 64KB page configuration.
PHYS_OFFSET is calculated at run-time and stored in a variable (no
run-time code patching at this stage).
On the current implementation, both user and kernel address spaces are
512G (39-bit) each with a maximum of 256G for the RAM linear mapping.
Linux uses 3 levels of translation tables with the 4K page configuration
and 2 levels with the 64K configuration. Extending the memory space
beyond 39-bit with the 4K pages or 42-bit with 64K pages requires an
additional level of translation tables.
The SPARSEMEM configuration is global to all AArch64 platforms and
allows for 1GB sections with SPARSEMEM_VMEMMAP enabled by default.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The patch contains the exception entry code (kernel/entry.S), pt_regs
structure and related accessors, undefined instruction trapping and
stack tracing.
AArch64 Linux kernel (including kernel threads) runs in EL1 mode using
the SP1 stack. The vectors don't have a fixed address, only alignment
(2^11) requirements.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The patch adds the kernel booting and the initial setup code.
Documentation/arm64/booting.txt describes the booting protocol on the
AArch64 Linux kernel. This is subject to change following the work on
boot standardisation, ACPI.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This patch introduces several assembly macros and definitions used in
the .S files across arch/arm64/ like IRQ disabling/enabling, together
with asm-offsets.c.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This is a set of two bug fixes. One is the ATOMIC problem which is now
causing a compile failure in certain situations. The other is mishandling of
PER_LINUX32 which may also cause user visible effects.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQQN+IAAoJEDeqqVYsXL0Mza8H/RZHZSk6xRkMXXnmNXeoPpQT
HH8ILKJtfzLDhsurznNUFcHvUeU0QiwAey9NXTuJ6leXa/f9nsRtE1izejGWbxId
1JQPH0VFz0913y9PtmWMfLedKuQLt3muynKyXbfkUO6jZsfbJK4XcU2rVHHDpPh7
PgbtWQmsOqqpmsR3sN3TcU/NglACCw27V4ZhHqoFfru2loyS84BcjdYRIxoMr6W8
AldXulb0RSBseOQXvDrp5XJMV7i75WYx2EM5l8YfK4rFC/kT0TMaTGfzTLjZRjMd
bgY2e/PEZhCzTK23+d4WtrtghKD+fTtWOJoAx5a1DZP/w/A8S9Lp7xzNJ7X2MD8=
=7In9
-----END PGP SIGNATURE-----
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is a set of two bug fixes. One is the ATOMIC problem which is
now causing a compile failure in certain situations. The other is
mishandling of PER_LINUX32 which may also cause user visible effects.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix personality flag check in copy_thread()
[PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
Pull s390 fixes from Martin Schwidefsky:
"A couple of s390 bug fixes for 3.5-rc4"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/32: Don't clobber personality flags on exec
s390/smp: add missing smp_store_status() for !SMP
s390/dasd: fix ioctl return value
s390: Always use "long" for ssize_t to match size_t
In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this compile error:
arch/s390/kernel/machine_kexec.c: In function ‘setup_regs’:
arch/s390/kernel/machine_kexec.c:63:3: error: implicit declaration
of function ‘smp_store_status’ [-Werror=implicit-function-declaration]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
KVM_GET_MSR was missing support for PV EOI,
which is needed for migration.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Bug fixes for various ARM platforms. About half of these are
for OMAP and submitted before but did not make it into v3.6-rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tupl
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for various ARM platforms. About half of these are for OMAP
and submitted before but did not make it into v3.6-rc2."
* tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
ARM: mv78xx0: fix win_cfg_base prototype
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: mmp: fix potential NULL dereference
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
...
- Revert the kexec fix which caused on non-kexec shutdowns a race.
- Reuse existing P2M leafs - instead of requiring to allocate a large
area of bootup virtual address estate.
- Fix a one-off error when adding PFNs for balloon pages.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQNppKAAoJEFjIrFwIi8fJU/oH/jdWdRqJgC5mCnu9LwrIemEj
gPTAcKw01A/2vbOY5rfXx7rCpgeU5ZM/XSt0byz/J5q0bmjjKVM106Smq1s7EaQx
OjsdLglWoZYzKJjXH/FEKRPD39f/hd+KNJu3aGEJM8UZ0htvxlg6ACGzVPJa83Pf
yrRXSycxvEevbGbuwWdNubxD5WKMMmbzi/HGGfdtL4256d0xIgxMrYgskLek96cR
cg11llC5QLzH8mX+M5iX0lchASvMITyERXyEKK2opFN8a/766yi16agP75RKZdkP
kWXp0vyOMrpy9UnOs2V1XLc/ufqNwHLcPVfecScXhz8xZWrZYOBdJQf7HAWxvLE=
=MgvT
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull three xen bug-fixes from Konrad Rzeszutek Wilk:
- Revert the kexec fix which caused on non-kexec shutdowns a race.
- Reuse existing P2M leafs - instead of requiring to allocate a large
area of bootup virtual address estate.
- Fix a one-off error when adding PFNs for balloon pages.
* tag 'stable/for-linus-3.6-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/setup: Fix one-off error when adding for-balloon PFNs to the P2M.
xen/p2m: Reuse existing P2M leafs if they are filled with 1:1 PFNs or INVALID.
Revert "xen PVonHVM: move shared_info to MMIO before kexec"
Pull powerpc fixes from Benjamin Herrenschmidt:
"I meant to sent that earlier but got swamped with other things, so
here are some powerpc fixes for 3.6. A few regression fixes and some
bug fixes that I deemed should still make it.
There's a FSL update from Kumar with a bunch of defconfig updates
along with a few embedded fixes.
I also reverted my g5_defconfig update that I merged earlier as it was
completely busted, not too sure what happened there, I'll do a new one
later."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
Revert "powerpc: Update g5_defconfig"
powerpc/perf: Use pmc_overflow() to detect rolled back events
powerpc: Fix VMX in interrupt check in POWER7 copy loops
powerpc: POWER7 copy_to_user/copy_from_user patch applied twice
powerpc: Fix personality handling in ppc64_personality()
powerpc/dma-iommu: Fix IOMMU window check
powerpc: Remove unnecessary ifdefs
powerpc/kgdb: Restore current_thread_info properly
powerpc/kgdb: Bail out of KGDB when we've been triggered
powerpc/kgdb: Do not set kgdb_single_step on ppc
powerpc/mpic_msgr: Add missing includes
powerpc: Fix null pointer deref in perf hardware breakpoints
powerpc: Fixup whitespace in xmon
powerpc: Fix xmon dl command for new printk implementation
powerpc/fsl: fix "Failed to mount /dev: No such device" errors
powerpc/fsl: update defconfigs
booke/wdt: some ioctls do not return values properly
powerpc/p4080ds: dts - add usb controller version info and port0
powerpc/85xx: mpc85xx_defconfig - add VIA PATA support for MPC85xxCDS
powerpc/fsl-pci: Only scan PCI bus if configured as a host
Pull kvm fixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86 emulator: use stack size attribute to mask rsp in stack ops
KVM: MMU: Fix mmu_shrink() so that it can free mmu pages as intended
ppc: e500_tlb memset clears nothing
KVM: PPC: Add cache flush on page map
KVM: PPC: Book3S HV: Fix incorrect branch in H_CEDE code
KVM: x86: update KVM_SAVE_MSRS_BEGIN to correct value
Pull MIPS fixes from Ralf Baechle:
"Random fixes across the MIPS tree. The two hotspots are several bugs
in the module loader and the ath79 SOC support; also noteworthy is the
restructuring of the code to synchronize CPU timers across CPUs on
startup; the old code recently ceased to work due to unrelated
changes.
All except one of these patches have sat for a significant time in
linux-next for testing."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: pci-ar724x: avoid data bus error due to a missing PCIe module
MIPS: Malta: Delete duplicate PCI fixup.
MIPS: ath79: don't hardcode the unavailability of the DSP ASE
MIPS: Synchronize MIPS count one CPU at a time
MIPS: BCM63xx: Fix SPI message control register handling for BCM6338/6348.
MIPS: Module: Deal with malformed HI16/LO16 relocation sequences.
MIPS: Fix race condition in module relocation code.
MIPS: Fix memory leak in error path of HI16/LO16 relocation handling.
MIPS: MTX-1: Add udelay to mtx1_pci_idsel
MIPS: ath79: select HAVE_CLK
MIPS: ath79: Use correct IRQ number for the OHCI controller on AR7240
MIPS: ath79: Fix number of GPIO lines for AR724[12]
MIPS: Octeon: Fix broken interrupt controller code.
This reverts commit b1acf1bb54.
Something went horribly wrong when I did savedefconfig, not sure what,
but what's in there is busted so let's revert it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For certain speculative events on Power7, 'perf stat' reports far higher
event count than 'perf record' for the same event.
As described in following commit, a performance monitor exception is raised
even when the the performance events are rolled back.
commit 0837e3242c
Author: Anton Blanchard <anton@samba.org>
Date: Wed Mar 9 14:38:42 2011 +1100
perf_event_interrupt() records an event only when an overflow occurs. But
this check for overflow is a simple 'if (val < 0)'.
Because the events are rolled back, this check for overflow fails and the
event is not recorded. perf_event_interrupt() later uses pmc_overflow() to
detect the overflow and resets the counters and the events are lost completely.
To properly detect the overflow of rolled back events, use pmc_overflow()
even when recording events.
To reproduce:
$ cat strcpy.c
#include <stdio.h>
#include <string.h>
main()
{
char buf[256];
alarm(5);
while(1)
strcpy(buf, "string1");
}
$ perf record -e r20014 ./strcpy
$ perf report -n > report.1
$ perf stat -e r20014 > report.2
# Compare report.1 and report.2
Reported-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The enhanced prefetch hint patches corrupt the condition register
that was used to check if we are in interrupt. Fix this by using cr1.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
"powerpc: Use enhanced touch instructions in POWER7
copy_to_user/copy_from_user" was applied twice. Remove one.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Directly comparing current->personality against PER_LINUX32 doesn't work
in cases when any of the personality flags stored in the top three bytes
are used.
Directly forcefully setting personality to PER_LINUX32 or PER_LINUX
discards any flags stored in the top three bytes
Use personality() macro to compare only PER_MASK bytes and make sure that
we are setting only the bits that should be set, instead of overwriting
the whole value.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Checking for device mask to cover the whole IOMMU table is too strict.
IOMMU allocators should handle mask constraint properly for each
allocation.
The patch enables to use old AirPort Extreme cards on PowerMacs with
more than 1GB of memory; without the patch the driver init fails with:
b43-pci-bridge 0001:01:01.0: Warning: IOMMU window too big for device mask
b43-pci-bridge 0001:01:01.0: mask: 0x3fffffff, table end: 0x80000000
b43-phy0 ERROR: The machine/kernel does not support the required 30-bit DMA mask
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For powerpc BooKE and e200, singlestep is handled on the critical/dbg
exception stack. This causes current_thread_info() to fail for kgdb
internal, so previously We work around this issue by copying
the thread_info from the kernel stack before calling kgdb_handle_exception,
and copying it back afterwards.
But actually we don't do this properly. We should backup current_thread_info
then restore that when exit.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to skip a breakpoint exception when it occurs after
a breakpoint has already been removed.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kgdb_single_step flag has the possibility to indefinitely
hang the system on an SMP system.
The x86 arch have the same problem, and that problem was fixed by
commit 8097551d9ab9b9e3630(kgdb,x86: do not set kgdb_single_step
on x86). This patch does the same behaviors as x86's patch.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add several #includes that mpic_msgr relies on being pulled implicitly,
which only happens on certain configs.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Meador Inge <meador_inge@mentor.com>
Cc: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently if you are doing a global perf recording with hardware
breakpoints (ie perf record -e mem:0xdeadbeef -a), you can oops with:
Faulting instruction address: 0xc000000000738890
cpu 0xc: Vector: 300 (Data Access) at [c0000003f76af8d0]
pc: c000000000738890: .hw_breakpoint_handler+0xa0/0x1e0
lr: c000000000738830: .hw_breakpoint_handler+0x40/0x1e0
sp: c0000003f76afb50
msr: 8000000000001032
dar: 6f0
dsisr: 42000000
current = 0xc0000003f765ac00
paca = 0xc00000000f262a00 softe: 0 irq_happened: 0x01
pid = 6810, comm = loop-read
enter ? for help
[c0000003f76afbe0] c00000000073cd04 .notifier_call_chain.isra.0+0x84/0xe0
[c0000003f76afc80] c00000000073cdbc .notify_die+0x3c/0x60
[c0000003f76afd20] c0000000000139f0 .do_dabr+0x40/0xf0
[c0000003f76afe30] c000000000005a9c handle_dabr_fault+0x14/0x48
--- Exception: 300 (Data Access) at 0000000010000480
SP (ff8679e0) is in userspace
This is because we don't check to see if the break point is associated
with task before we deference the task_struct pointer.
This changes the update to use current.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are a few whitespace goolies in xmon.c, some of them appear to
be my fault. Fix them all in one go.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the printk internals were reworked the xmon 'dl' command which
dumps the content of __log_buf has stopped working.
It is now a structured buffer, so just dumping it doesn't really work.
Use the helpers added for kgdb to print out the content.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Yocto (Built by Poky 7.0) 1.2 root filesystems fail to boot,
at least over nfs, with:
Failed to mount /dev: No such device
Configuring DEVTMPFS fixes it.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
run make savedefconfig on fsl defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Small platform specific bug fixes for problems found in randconfig builds.
* randconfig/mach:
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Using 'select' in Kconfig is hard, a platform cannot just
enable a driver without also making sure that its subsystem
is there. Also, there is no actual code dependency between
the platform and the gpio leds driver.
Without this patch, building without LEDS_CLASS esults in:
drivers/built-in.o: In function `create_gpio_led.part.2':
governor_userspace.c:(.devinit.text+0x5a58): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `gpio_led_remove':
governor_userspace.c:(.devexit.text+0x6b8): undefined reference to `led_classdev_unregister'
This reverts 8733f53c6 "ARM: ux500: Kconfig: Compile in leds-gpio
support for Snowball" that introduced the regression and did not
provide a helpful explanation.
In order to leave the GPIO LED code still present in normal
builds, this also enables the symbol in u8500_defconfig, in addition
to the other LED drivers that are already selected there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
The head-v7.S contains a call to the generic cpu_suspend function,
which is only available when selected by the i.MX6 code. As
pointed out by Shawn Guo, i.MX5 does not actually use any
functions defined in head-v7.S. It is also needed only for
the i.MX6 power management code and for the SMP code, so
we can restrict building this file to situations in which
at least one of those two is present.
Finally, other platforms with a similar file call it headsmp.S,
so we can rename it to the same for consistency.
Without this patch, building imx5 standalone results in:
arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
arch/arm/mach-imx/head-v7.S:104: undefined reference to `cpu_resume'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Miao <eric.miao@linaro.org>
Cc: stable@vger.kernel.org
The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.
Building IMX without CPU_FREQ_TABLE results in:
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org
The ksz9021rn_phy_fixup and mx6q_sabrelite functions try to
set up an ethernet phy if they can. They do check whether
phylib is enabled, but unfortunately the functions can only
be called from platform code if phylib is builtin, not
if it is a module
Without this patch, building with a modular phylib results in:
arch/arm/mach-imx/mach-imx6q.c: In function 'imx6q_sabrelite_init':
arch/arm/mach-imx/mach-imx6q.c:120:5: error: 'ksz9021rn_phy_fixup' undeclared (first use in this function)
arch/arm/mach-imx/mach-imx6q.c:120:5: note: each undeclared identifier is reported only once for each function it appears in
The bug was originally reported by Artem Bityutskiy but only
partially fixed in ef441806 "ARM: imx6q: register phy fixup only when
CONFIG_PHYLIB is enabled".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
This moves the imx5 pm code out of the list of unconditionally
compiled files for imx5, mirroring what we already do for imx6
and how it was done before the code was move from mach-mx5 to
mach-imx in v3.3.
Without this patch, building with CONFIG_PM disabled results in:
arch/arm/mach-imx/pm-imx5.c:202:116: error: redefinition of 'imx51_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:154:91: note: previous definition of 'imx51_pm_init' was here
arch/arm/mach-imx/pm-imx5.c:209:116: error: redefinition of 'imx53_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:155:91: note: previous definition of 'imx53_pm_init' was here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
The new omap4 cpuidle implementation currently requires
ARCH_NEEDS_CPU_IDLE_COUPLED, which only works on SMP.
This patch makes it possible to build a non-SMP kernel
for that platform. This is not normally desired for
end-users but can be useful for testing.
Without this patch, building rand-0y2jSKT results in:
drivers/cpuidle/coupled.c: In function 'cpuidle_coupled_poke':
drivers/cpuidle/coupled.c:317:3: error: implicit declaration of function '__smp_call_function_single' [-Werror=implicit-function-declaration]
It's not clear if this patch is the best solution for
the problem at hand. I have made sure that we can now
build the kernel in all configurations, but that does
not mean it will actually work on an OMAP44xx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/h+C
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij <linus.walleij@linaro.org>:
Here are two audio fixes for the ux500 found by Lee Jones.
* tag 'ux500-fixes-v3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
For HDMI, already HDMI support for EXYNOS in mainline kernel is broken
because its configuration moved to platform data but regarding platform
data didn't support yet. And others are for fix warnings.
* 'v3.6-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set HDMI platform data in Origen board
ARM: EXYNOS: Set HDMI platform data in SMDKV310
ARM: SAMSUNG: Add API to set platform data for s5p-tv driver
ARM: SAMSUNG: Set HDMI platform data for Exynos4x12 SoCs
ARM: Samsung: Make uart_save static in pm.c file
ARM: S3C24XX: Fix s3c2410_dma_enqueue parameters
ARM: S3C24XX: Add missing DMACH_DT_PROP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When we are finished with return PFNs to the hypervisor, then
populate it back, and also mark the E820 MMIO and E820 gaps
as IDENTITY_FRAMEs, we then call P2M to set areas that can
be used for ballooning. We were off by one, and ended up
over-writting a P2M entry that most likely was an IDENTITY_FRAME.
For example:
1-1 mapping on 40000->40200
1-1 mapping on bc558->bc5ac
1-1 mapping on bc5b4->bc8c5
1-1 mapping on bc8c6->bcb7c
1-1 mapping on bcd00->100000
Released 614 pages of unused memory
Set 277889 page(s) to 1-1 mapping
Populating 40200-40466 pfn range: 614 pages added
=> here we set from 40466 up to bc559 P2M tree to be
INVALID_P2M_ENTRY. We should have done it up to bc558.
The end result is that if anybody is trying to construct
a PTE for PFN bc558 they end up with ~PAGE_PRESENT.
CC: stable@vger.kernel.org
Reported-by-and-Tested-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the controller has no PCIe module attached, accessing of the device
configuration space causes a data bus error. Avoid this by checking the
status of the PCIe link in advance, and indicate an error if the link
is down.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4293/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The binding doc and dts use properties "fsl,{cd,wp}-internal" while
esdhc driver uses "fsl,{cd,wp}-controller". Fix binding doc and dts
to get them match driver code.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Chris Ball <cjb@laptop.org>
Though commit 602bf40 (ARM: imx6: exit coherency when shutting down
a cpu) improves the stability of imx6q cpu hotplug a lot, there are
still hangs seen with a more stressful hotplug testing.
It's expected that once imx_enable_cpu(cpu, false) is called, the cpu
will be taken down by hardware immediately, and the code after that
will not get any chance to execute. However, this is not always the
case from the testing. The cpu could possibly be alive for a few
cycles before hardware actually takes it down. So rather than letting
cpu execute some code that could cause a hang in these cycles, let's
make the cpu spin there and wait for hardware to take it down.
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This issue was recently observed on an AMD C-50 CPU where a patch of
maximum size was applied.
Commit be62adb492 ("x86, microcode, AMD: Simplify ucode verification")
added current_size in get_matching_microcode(). This is calculated as
size of the ucode patch + 8 (ie. size of the header). Later this is
compared against the maximum possible ucode patch size for a CPU family.
And of course this fails if the patch has already maximum size.
Cc: <stable@vger.kernel.org> [3.3+]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1344361461-10076-1-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The sub-register used to access the stack (sp, esp, or rsp) is not
determined by the address size attribute like other memory references,
but by the stack segment's B bit (if not in x86_64 mode).
Fix by using the existing stack_mask() to figure out the correct mask.
This long-existing bug was exposed by a combination of a27685c33a
(emulate invalid guest state by default), which causes many more
instructions to be emulated, and a seabios change (possibly a bug) which
causes the high 16 bits of esp to become polluted across calls to real
mode software interrupts.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Catalin Marinas
Linus Torvalds
Heiko Carstens
Michael S. Tsirkin
Benjamin Herrenschmidt
Sukadev Bhattiprolu
Anton Blanchard
Jiri Kosina
Aaro Koskinen
Michael Neuling
Tiejun Chen
Scott Wood
Michael Ellerman
Kim Phillips
Arnd Bergmann
Konrad Rzeszutek Wilk
Gabor Juhos
Shawn Guo
Andreas Herrmann
Avi Kivity