Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current users of of_mdio_find_bus() leak a struct device refcount, as
they fail to clean up the reference obtained inside class_find_device().
Fix the DSA code to properly refcount the returned MDIO bus by:
1. taking a reference on the struct device whenever we assign it to
pd->chip[x].host_dev.
2. dropping the reference when we overwrite the existing reference.
3. dropping the reference when we free the data structure.
4. dropping the initial reference we obtained after setting up the
platform data structure, or on failure.
In step 2 above, where we obtain a new MDIO bus, there is no need to
take a reference on it as we would only have to drop it immediately
after assignment again, iow:
put_device(cd->host_dev); /* drop original assignment ref */
cd->host_dev = get_device(&mdio_bus_switch->dev); /* get our ref */
put_device(&mdio_bus_switch->dev); /* drop of_mdio_find_bus ref */
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdio_find_bus() leaks a struct device refcount, caused by using
class_find_device() and not realising that the device reference has
its refcount incremented:
* Note, you will need to drop the reference with put_device() after use.
...
while ((dev = class_dev_iter_next(&iter))) {
if (match(dev, data)) {
get_device(dev);
break;
}
Update the comment, and arrange for the phy code to drop this refcount
when disposing of a reference to it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal management fixes from Zhang Rui:
- Power allocator governor changes to allow binding on thermal zones
with missing power estimates information. From Javi Merino.
- Add compile test flags on thermal drivers that allow it without
producing compilation errors. From Eduardo Valentin.
- Fixes around memory allocation on cpu_cooling. From Javi Merino.
- Fix on db8500 cpufreq code to allow autoload. From Luis de
Bethencourt.
- Maintainer entries for cpu cooling device
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: power_allocator: exit early if there are no cooling devices
thermal: power_allocator: don't require tzp to be present for the thermal zone
thermal: power_allocator: relax the requirement of two passive trip points
thermal: power_allocator: relax the requirement of a sustainable_power in tzp
thermal: Add a function to get the minimum power
thermal: cpu_cooling: free power table on error or when unregistering
thermal: cpu_cooling: don't call kcalloc() under rcu_read_lock
thermal: db8500_cpufreq_cooling: Fix module autoload for OF platform driver
thermal: cpu_cooling: Add MAINTAINERS entry
thermal: ti-soc: Kconfig fix to avoid menu showing wrongly
thermal: ti-soc: allow compile test
thermal: qcom_spmi: allow compile test
thermal: exynos: allow compile test
thermal: armada: allow compile test
thermal: dove: allow compile test
thermal: kirkwood: allow compile test
thermal: rockchip: allow compile test
thermal: spear: allow compile test
thermal: hisi: allow compile test
thermal: Fix thermal_zone_of_sensor_register to match documentation
The residue calculation may provide a wrong estimation when the transfer is
started. There are possible scenarios we have to separate:
1) the transfer is not started yet; residue is equal to the total
length;
2) the transfer is just started (first chunk is ongoing); residue is
equal to the total length without already transfered bytes;
3) the transfer is ongoing and we already sent few chunks of data;
residue is equal to the total length without fully transfered chunks
and already sent bytes.
Mistakenly the calculation in cases 2) and 3) was done in the similar way and
the result is equal to -bytes that have been transfered, i.e. quite big since
size_t type can't keep negative values.
Rewrite the calculation algorithm to be one pass and have a correct result.
Besides above in case user asks for a status of the active DMA descriptor
without pausing an ongoing transfer the residue will be estimated based on the
register value, though it's still racy. Since the transfer is active the value
is continuously being changed. Here we have to read two registers at a time. To
minimize an error make those reads close to each other.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the commit to have an allocated list of virtual descriptors was
reverted, the pxa_dma driver is broken, as it assumes the descriptor is
placed on the allocated list upon allocation.
Fix the issue in pxa_dma by making an allocated virtual descriptor a
singleton.
Fixes: 8c8fe97b2b ("Revert "dmaengine: virt-dma: don't always free descriptor upon completion"")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Section 3.2 "Device Runtime Power Management" of pci.txt has become
outdated, so update it to correctly reflect the current code flow.
Also update the comment in local_pci_probe() to document the fact
that pm_runtime_put_noidle() is not the only runtime PM helper
function that can be used to decrement the device's runtime PM
usage counter in .probe().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBI2/AAoJEMhvYp4jgsXi08cH/11S/92w1PLNmWCv4y7TXHQw
XTJi7/Hk+q6otV/FigXukdYClR17h/3mFyCKKXHrkAgy/AoSrvN/ABe0bLLoT2AQ
xh0Rx8F6vZwa6ro1MZcrn3ZxQkoJlNUhoIXtY84oSPWd1ernLOar6HonFiynCQQc
bDZo5zoLj6DBbSO+UpVvEQN57ogwPgFZ1hGDjJeyyH8c1755z2OVA+k8O0dwjmqW
Xav/7TO8bFEIbUnfWeKnVyK45qmJxHcTbn3nxUgYFQj3DMI2Hn86WEY4cg8QvTo+
SpdO1Aio6b9NSTNnpiSvPnc2MFNPFaWjiqm1w86w+PTm8oUT+p1V0OG/EE27fcY=
=VUfk
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
* tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: arm: Fix typo in the idle-states bindings examples
gpio: mention in DT binding doc that <name>-gpio is deprecated
of_pci_irq: Silence bogus "of_irq_parse_pci() failed ..." messages.
devicetree: bindings: Extend the bma180 bindings with bma250 info
of: thermal: Mark cooling-*-level properties optional
of: thermal: Fix inconsitency between cooling-*-state and cooling-*-level
Docs: dt: add #msi-cells to GICv3 ITS binding
of: add vendor prefix for Socionext Inc.
of_property_count_u32_elems() will never return 0, but a -ve error value
of a positive count. And so the current !count check is wrong.
Also, a missing "opp-microvolt" property isn't a problem and so we need
to do of_find_property() separately to confirm that.
Fixes: 274659029c (PM / OPP: Add support to parse "operating-points-v2" bindings)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
so that they can read the edid of connected displays.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWAdpbAAoJEPOmecmc0R2B9DgH/1Il++FcqJRQfk1HoSEXeD3s
A2PX1eDlE984LcA2G/JQZ10iZxcLx07jg4pxRUcEDJ7iMdFrBFg4B7uHL5iM6kp5
iAhSkRthsuwTpY9ySLe03izjF0a/9+0FvGdG939x7Hlfk4qhtb+ynzvMJcZ9Bs3n
oxvvXqBBkEbK1vnySJkDnDCnK3fRBUse7QRcxKY2YdSYyxdw9Ga51hReF71pyH4u
t7+8+4Pniz68i22YYW/zbGsO79f9tpmT7pisIfNnUOu11gDkL9oX3WkzeJWNh5BC
9guT9CF1c+DLshSWYVDHZ+TCjwVFpgpz3osAKd10FUzWQctU1H/4FGaYviwNILY=
=c2bs
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rockchip32-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Add the ddc-i2c-bus reference to the veyron hdmi nodes,
so that they can read the edid of connected displays.
* tag 'v4.3-rockchip32-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: Add ddc i2c reference to veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
STI drm drivers probe and bind using component framework was incorrect.
In addition to drivers fix DT update is needed to make all sub-components
become childs of sti-display-subsystem.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
"ARM: dts: <omap2/omap4/omap5/dra7>: add minimal l4 bus
layout with control module support" moved pbias_regulator dt node
from being a child node of ocp to be the child node of
'syscon'. Since 'syscon' doesn't have the 'ranges' property,
address translation fails while trying to convert the address
to resource. Fix it here by populating 'ranges' property in
syscon dt node.
Fixes: 72b10ac00e ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support")
Fixes: 7415b0b4c6 ("ARM: dts: omap4: add minimal l4 bus layout
with control module support")
Fixes: ed8509eddd ("ARM: dts: omap5: add minimal l4 bus
layout with control module support")
Fixes: d919501fef ("ARM: dts: dra7: add minimal l4 bus
layout with control module support")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: fixed omap3 pbias to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently error log messages in ip6_tnl_err are printed at 'warn'
level. This is different to other tunnel types which don't print
any messages. These log messages don't provide any information that
couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The gpiolib supports parsing DT properties of the form <name>-gpio but it
was only added for compatibility with older DT bindings that got it wrong
and should not be used in newer bindings.
The commit that added support for this was:
dd34c37aa3 ("gpio: of: Allow -gpio suffix for property names")
but didn't update the documentation to explain this so it's been a source
of confusion. So let's make this clear in the GPIO DT binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull drm fixes from Dave Airlie:
"Most of the GPU drivers people were at XDC last week, so I didn't get
much to send, so I let it rollover until this week.
Also Alex was away for 3 weeks so amdgpu/radeon got a bit more stuff
than usual in one go.
I've been trying to figure out some 4.2 issues with i915 still (that
are fixed in 4.3, but bisecting ends up in a merge commit). Hopefully
next week I or i915 people can work that out"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (46 commits)
drm: Allow also control clients to check the drm version
drm/vmwgfx: Fix uninitialized return in vmw_kms_helper_dirty()
drm/vmwgfx: Fix uninitialized return in vmw_cotable_unbind()
drm/layerscape: fix handling fsl_dcu_drm_plane_index result
drm/mgag200: Fix driver_load error handling
drm/mgag200: Fix error handling paths in fbdev driver
drm/qxl: only report first monitor as connected if we have no state
drm/radeon: add quirk for MSI R7 370
drm/amdgpu: Sprinkle drm_modeset_lock_all to appease locking checks
drm/radeon: Sprinkle drm_modeset_lock_all to appease locking checks
drm/amdgpu: sync ce and me with SWITCH_BUFFER(2)
drm/amdgpu: integer overflow in amdgpu_mode_dumb_create()
drm/amdgpu: info leak in amdgpu_gem_metadata_ioctl()
drm/amdgpu: integer overflow in amdgpu_info_ioctl()
drm/amdgpu: unwind properly in amdgpu_cs_parser_init()
drm/amdgpu: Fix max_vblank_count value for current display engines
drm/amdgpu: use kmemdup rather than duplicating its implementation
drm/amdgpu: fix UVD suspend and resume for VI APU
drm/amdgpu: fix the UVD suspend sequence order
drm/amdgpu: make UVD handle checking more strict
...
* VHT MCS mask array overrun, reported by Dan Carpenter
* reset CQM history to always get a notification, from Sara Sharon
-----BEGIN PGP SIGNATURE-----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=4Ui5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two small fixes:
* VHT MCS mask array overrun, reported by Dan Carpenter
* reset CQM history to always get a notification, from Sara Sharon
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently error log messages in ip6gre_err are printed at 'warn'
level. This is different to most other tunnel types which don't
print any messages. These log messages don't provide any information
that couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
dump_rules returns skb length and not error.
But when family == AF_UNSPEC, the caller of dump_rules
assumes that it returns an error. Hence, when family == AF_UNSPEC,
we continue trying to dump on -EMSGSIZE errors resulting in
incorrect dump idx carried between skbs belonging to the same dump.
This results in fib rule dump always only dumping rules that fit
into the first skb.
This patch fixes dump_rules to return error so that we exit correctly
and idx is correctly maintained between skbs that are part of the
same dump.
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Renesas R8A7794 SoC support to the Renesas R-Car gen2 PCI driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
Commit 932c435cab ("PCI: Add dev_flags bit to access VPD through function
0") passes PCI_SLOT(devfn) for the devfn parameter of pci_get_slot().
Generally this works because we're fairly well guaranteed that a PCIe
device is at slot address 0, but for the general case, including
conventional PCI, it's incorrect. We need to get the slot and then convert
it back into a devfn.
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
SR-IOV creates a virtual bus where bus->self is NULL. When we add VFs and
scan for an MSI domain, pci_set_bus_msi_domain() dereferences bus->self,
which causes a kernel NULL pointer dereference oops.
Scan up to the parent bus until we find a real bridge where we can get the
MSI domain.
[bhelgaas: changelog]
Fixes: 44aa0c657e ("PCI/MSI: Add hooks to populate the msi_domain field")
Tested-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
After a good amount of debugging, I found bnx2x was byte swaping
the 40 bytes of rss_key.
If we byte swap the key, then bnx2x generates hashes matching
MSDN specs as documented in (Verifying the RSS Hash Calculation)
https://msdn.microsoft.com/en-us/library/windows/hardware/ff571021%
28v=vs.85%29.aspx
It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fw filter uses tp->root==NULL to check if it is the old method,
so it doesn't need allocation at all in this case. This patch
reverts the offending commit and adds some comments for old
method to make it obvious.
Fixes: 33f8b9ecdb ("net_sched: move tp->root allocation into fw_init()")
Reported-by: Akshat Kakkar <akshat.1984@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
ocfs2/dlm: fix deadlock when dispatch assert master
membarrier: clean up selftest
vmscan: fix sane_reclaim helper for legacy memcg
lib/iommu-common.c: do not try to deref a null iommu->lazy_flush() pointer when n < pool->hint
x86, efi, kasan: #undef memset/memcpy/memmove per arch
mm: migrate: hugetlb: putback destination hugepage to active list
mm, dax: VMA with vm_ops->pfn_mkwrite wants to be write-notified
userfaultfd: register uapi generic syscall (aarch64)
userfaultfd: selftest: don't error out if pthread_mutex_t isn't identical
userfaultfd: selftest: return an error if BOUNCE_VERIFY fails
userfaultfd: selftest: avoid my_bcmp false positives with powerpc
userfaultfd: selftest: only warn if __NR_userfaultfd is undefined
userfaultfd: selftest: headers fixup
userfaultfd: selftests: vm: pick up sanitized kernel headers
userfaultfd: revert "userfaultfd: waitqueue: add nr wake parameter to __wake_up_locked_key"
Jiri Benc says:
====================
lwtunnel: make it really work, for IPv4
One of the selling points of lwtunnel was the ability to specify the tunnel
destination using routes. However, this doesn't really work currently, as
ARP and ndisc replies are not handled correctly. ARP and ndisc replies won't
have tunnel metadata attached, thus they will be sent out with the default
parameters or not sent at all, either way never reaching the requester.
Most of the egress tunnel parameters can be inferred from the ingress
metada. The only and important exception is UDP ports. This patchset infers
the egress data from the ingress data and disallow settings of UDP ports in
tunnel routes. If there's a need for different UDP ports, a new interface
needs to be created for each port combination. Note that it's still possible
to specify the UDP ports to use, it just needs to be done while creating the
vxlan/geneve interface.
This covers only ARPs. IPv6 ndisc has the same problem but is harder to
solve, as there's already dst attached to outgoing skbs. Ideas to solve this
are welcome.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP tunnel config is asymmetric wrt. to the ports used. The source and
destination ports from one direction of the tunnel are not related to the
ports of the other direction. We need to be able to respond to ARP requests
using the correct ports without involving routing.
As the consequence, UDP ports need to be fixed property of the tunnel
interface and cannot be set per route. Remove the ability to set ports per
route. This is still okay to do, as no kernel has been released with these
attributes yet.
Note that the ability to specify source and destination ports is preserved
for other users of the lwtunnel API which don't use routes for tunnel key
specification (like openvswitch).
If in the future we rework ARP handling to allow port specification, the
attributes can be added back.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ip lwtunnels, the additional data for xmit (basically, the actual
tunnel to use) are carried in ip_tunnel_info either in dst->lwtstate or in
metadata dst. When replying to ARP requests, we need to send the reply to
the same tunnel the request came from. This means we need to construct
proper metadata dst for ARP replies.
We could perform another route lookup to get a dst entry with the correct
lwtstate. However, this won't always ensure that the outgoing tunnel is the
same as the incoming one, and it won't work anyway for IPv4 duplicate
address detection.
The only thing to do is to "reverse" the ip_tunnel_info.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN device can receive skb with checksum partial. But the checksum
offset could be in outer header which is pulled on receive. This results
in negative checksum offset for the skb. Such skb can cause the assert
failure in skb_checksum_help(). Following patch fixes the bug by setting
checksum-none while pulling outer header.
Following is the kernel panic msg from old kernel hitting the bug.
------------[ cut here ]------------
kernel BUG at net/core/dev.c:1906!
RIP: 0010:[<ffffffff81518034>] skb_checksum_help+0x144/0x150
Call Trace:
<IRQ>
[<ffffffffa0164c28>] queue_userspace_packet+0x408/0x470 [openvswitch]
[<ffffffffa016614d>] ovs_dp_upcall+0x5d/0x60 [openvswitch]
[<ffffffffa0166236>] ovs_dp_process_packet_with_key+0xe6/0x100 [openvswitch]
[<ffffffffa016629b>] ovs_dp_process_received_packet+0x4b/0x80 [openvswitch]
[<ffffffffa016c51a>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa0171383>] vxlan_rcv+0x53/0x60 [openvswitch]
[<ffffffffa01734cb>] vxlan_udp_encap_recv+0x8b/0xf0 [openvswitch]
[<ffffffff8157addc>] udp_queue_rcv_skb+0x2dc/0x3b0
[<ffffffff8157b56f>] __udp4_lib_rcv+0x1cf/0x6c0
[<ffffffff8157ba7a>] udp_rcv+0x1a/0x20
[<ffffffff8154fdbd>] ip_local_deliver_finish+0xdd/0x280
[<ffffffff81550128>] ip_local_deliver+0x88/0x90
[<ffffffff8154fa7d>] ip_rcv_finish+0x10d/0x370
[<ffffffff81550365>] ip_rcv+0x235/0x300
[<ffffffff8151ba1d>] __netif_receive_skb+0x55d/0x620
[<ffffffff8151c360>] netif_receive_skb+0x80/0x90
[<ffffffff81459935>] virtnet_poll+0x555/0x6f0
[<ffffffff8151cd04>] net_rx_action+0x134/0x290
[<ffffffff810683d8>] __do_softirq+0xa8/0x210
[<ffffffff8162fe6c>] call_softirq+0x1c/0x30
[<ffffffff810161a5>] do_softirq+0x65/0xa0
[<ffffffff810687be>] irq_exit+0x8e/0xb0
[<ffffffff81630733>] do_IRQ+0x63/0xe0
[<ffffffff81625f2e>] common_interrupt+0x6e/0x6e
Reported-by: Anupam Chanda <achanda@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a few drm/i915 fixes, including a fix to the recent regression
reported by Sedat Dilek
* tag 'drm-intel-fixes-2015-09-24' of git://anongit.freedesktop.org/drm-intel:
drm/i915/bios: handle MIPI Sequence Block v3+ gracefully
drm/i915: Add primary plane to mask if it's visible
drm/i915: workaround bad DSL readout v3
drm/i915: fix kernel-doc warnings in intel_audio.c
inode_cgwb_enabled() gates cgroup writeback support. If it returns
true, each inode is attached to the corresponding memory domain which
gets mapped to io domain. It currently only tests whether the
filesystem and bdi support cgroup writeback; however, cgroup writeback
support doesn't work on traditional hierarchies and thus it should
also test whether memcg and iocg are on the default hierarchy.
This caused traditional hierarchy setups to hit the cgroup writeback
path inadvertently and ended up creating separate writeback domains
for each memcg and mapping them all to the root iocg uncovering a
couple issues in the cgroup writeback path.
cgroup writeback was never meant to be enabled on traditional
hierarchies. Make inode_cgwb_enabled() test whether both memcg and
iocg are on the default hierarchy.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Artem Bityutskiy <dedekind1@gmail.com>
Reported-by: Dexuan Cui <decui@microsoft.com>
Link: http://lkml.kernel.org/g/1443012552.19983.209.camel@gmail.com
Link: http://lkml.kernel.org/g/f30d4a6aa8a546ff88f73021d026a453@SIXPR30MB031.064d.mgd.msft.net
On Mon, Sep 21, 2015 at 02:20:22PM -0400, Tejun Heo wrote:
>
> store_release and load_acquire are different from the usual memory
> barriers and can't be paired this way. You have to pair store_release
> and load_acquire. Besides, it isn't a particularly good idea to
OK I've decided to drop the acquire/release helpers as they don't
help us at all and simply pessimises the code by using full memory
barriers (on some architectures) where only a write or read barrier
is needed.
> depend on memory barriers embedded in other data structures like the
> above. Here, especially, rhashtable_insert() would have write barrier
> *before* the entry is hashed not necessarily *after*, which means that
> in the above case, a socket which appears to have set bound to a
> reader might not visible when the reader tries to look up the socket
> on the hashtable.
But you are right we do need an explicit write barrier here to
ensure that the hashing is visible.
> There's no reason to be overly smart here. This isn't a crazy hot
> path, write barriers tend to be very cheap, store_release more so.
> Please just do smp_store_release() and note what it's paired with.
It's not about being overly smart. It's about actually understanding
what's going on with the code. I've seen too many instances of
people simply sprinkling synchronisation primitives around without
any knowledge of what is happening underneath, which is just a recipe
for creating hard-to-debug races.
> > @@ -1539,7 +1546,7 @@ static int netlink_bind(struct socket *sock, struct sockaddr *addr,
> > }
> > }
> >
> > - if (!nlk->portid) {
> > + if (!nlk->bound) {
>
> I don't think you can skip load_acquire here just because this is the
> second deref of the variable. That doesn't change anything. Race
> condition could still happen between the first and second tests and
> skipping the second would lead to the same kind of bug.
The reason this one is OK is because we do not use nlk->portid or
try to get nlk from the hash table before we return to user-space.
However, there is a real bug here that none of these acquire/release
helpers discovered. The two bound tests here used to be a single
one. Now that they are separate it is entirely possible for another
thread to come in the middle and bind the socket. So we need to
repeat the portid check in order to maintain consistency.
> > @@ -1587,7 +1594,7 @@ static int netlink_connect(struct socket *sock, struct sockaddr *addr,
> > !netlink_allowed(sock, NL_CFG_F_NONROOT_SEND))
> > return -EPERM;
> >
> > - if (!nlk->portid)
> > + if (!nlk->bound)
>
> Don't we need load_acquire here too? Is this path holding a lock
> which makes that unnecessary?
Ditto.
---8<---
The commit 1f770c0a09 ("netlink:
Fix autobind race condition that leads to zero port ID") created
some new races that can occur due to inconcsistencies between the
two port IDs.
Tejun is right that a barrier is unavoidable. Therefore I am
reverting to the original patch that used a boolean to indicate
that a user netlink socket has been bound.
Barriers have been added where necessary to ensure that a valid
portid and the hashed socket is visible.
I have also changed netlink_insert to only return EBUSY if the
socket is bound to a portid different to the requested one. This
combined with only reading nlk->bound once in netlink_bind fixes
a race where two threads that bind the socket at the same time
with different port IDs may both succeed.
Fixes: 1f770c0a09 ("netlink: Fix autobind race condition that leads to zero port ID")
Reported-by: Tejun Heo <tj@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Nacked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lenovo Thinkpads with recent Realtek codecs seem suffering from click
noises at power transition since the introduction of widget power
saving in 4.1 kernel. Although this might be solved by some delays in
appropriate points, as a quick workaround, just disable the
power_save_node feature for now. The gain it gives is relatively
small, and this makes the situation back to pre 4.1 time.
This patch ended up with a bit more code changes than usual because
the existing fixup for Thinkpads is highly chained. Instead of adding
yet another chain, combine a few of them into a single fixup entry, as
a gratis cleanup.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=943982
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A disappointingly large set of fixes, though none of them very big and
very widely spread over many different drivers. Nothing especially
stands out, it's mostly all device specific and relatively minor.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBEMrAAoJECTWi3JdVIfQOqIH/jsO0wdDz683ZpUd0K3OQlss
gia5/e0pS4IOaQY4ECZSydC/wf+fGs0ZHlLWXqSzJ33abCUUZlfL4f/3kQwhIrgD
Tb4aFLQoTRglZIqsgEm91Mqpk9gFUxhhqRBhI77iw11SOG1uWdokkYISG0ljnR5p
HFVxmqiSubvKdtydTOWR446Gxrk97c8HjzoBOXvQ87hKKyos7oJi4OcYD6HDVNr9
hrPkHS/05anaLbehZr82jmL+yMDsQl7QMjk1ljRkuufDUB07HogM1FHb5zkecC9u
eqDy5SOSJY4XFINDpxqt/5nqDaKgPcbEpfCH+ajfeY0e3d8rVVnPurrz/H4ElUM=
=KbEn
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.3
A disappointingly large set of fixes, though none of them very big and
very widely spread over many different drivers. Nothing especially
stands out, it's mostly all device specific and relatively minor.
A disappointingly large collection of fixes for SPI issues, though
almost all in drivers (and there mainly the newly added Mediatek
driver) and the core fixes are documentation and error handling. The
driver fixes are all of the usual important if you see them variety.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBDUFAAoJECTWi3JdVIfQir4H/RIAsfP5QqSzjQHmeZk1eHJv
FIzUiHARK5Jy3ORXVCh3dh8JB67NF9Qa4p/fDcHhk0DFju+HTyvUHmChzGPwEw86
0lRv2PKhHu9e7vJG8IZXKbZKeBT9RtrVe8yQ7SLmQ+z0VxoVFaQwkWVKotzpL8wZ
YCOYGAtmxXvqWDiGuhzqG7RVLKW6vj8xz2BFqm5Gf6O32RpV9wFiNp2EtF8Hu+On
sMEqFWDqMbqIwUhcPKRI9+Zhj1TkzwNUawE+EgD4ydYVndYxSpqtn1veFc1Bv1xo
1FbntlDu/AzlPqtIFBzWLZNUxcwW+qKSjOCFlyCs+k1l6CEf+AoZAm1TsL+rVTw=
=3QsX
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A disappointingly large collection of fixes for SPI issues, though
almost all in drivers (and there mainly the newly added Mediatek
driver) and the core fixes are documentation and error handling.
The driver fixes are all of the usual 'important if you see them'
variety"
* tag 'spi-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: xtensa-xtfpga: fix register endianness
spi: meson: Fix module autoload for OF platform driver
spi: mediatek: fix wrong error return value on probe
spi: fix kernel-doc warnings in spi.h
spi: spidev: fix possible NULL dereference
spi: atmel: remove warning when !CONFIG_PM_SLEEP
spi: bcm2835: BUG: fix wrong use of PAGE_MASK
spi: mediatek: fix spi cs polarity error
spi: Fix documentation of spi_alloc_master()
spi: spi-pxa2xx: Check status register to determine if SSSR_TINT is disabled
spi: Mediatek: Document devicetree bindings update for spi bus
spi: mediatek: fix spi clock usage error
spi: mediatek: remove clk_disable_unprepare()
A collection of fixes that came in since I tagged the merge window pull
request for v4.3:
- Error handling fixes in the core.
- Fixes to a couple of TI drivers for device specific issues.
- Several fixes for module autoloading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBC+KAAoJECTWi3JdVIfQDQQH/12hjd3WRz9hfF9zH4+FY8AH
u44pBoA/bBJoiuJAQ809FmFNrWtBUaaLyQQbihDUgvqpkK8Kig7XZ1UABJEekpPR
ZBSmHLvLhpEmg6mtxrAVo+CW1ucKRfxw9Hob386D4bfD8OdZHYra7CgOsJzTtLqp
IkenSgv+IbM7uWJHUn3a2quMCvCKJa3kqLx1sqeXfO2a3HiJLeBu8BcIXmdkwPt/
h36KwgqTpk24VjevnVo4jYP0ap4Z3S9SSeVm3koUBMlz5LK78qj0zPd8sxTzNX+f
Ow24qwcn/alsqxrhBbWpcF1QJfcDliipB9oVJDxVcZ3arkY6FX06EzPxty+8y84=
=tftX
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A collection of fixes that came in since I tagged the merge window
pull request for v4.3:
- Error handling fixes in the core
- Fixes to a couple of TI drivers for device specific issues
- Several fixes for module autoloading"
* tag 'regulator-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: vexpress: Fix module autoload for OF platform driver
regulator: gpio: Fix module autoload for OF platform driver
regulator: anatop: Fix module autoload for OF platform driver
regulator: core: Correct return value check in regulator_resolve_supply
regulator: tps65218: Fix missing zero typo
regulator: pbias: program pbias register offset in pbias driver
regulator: core: fix possible NULL dereference
- DM thinp fix to properly advertise discard support as disabled for
thin devices backed by a thin-pool with discard support disabled.
- DM crypt fix to prevent the creation of bios that violate the
underlying block device's max_segments limits. This fixes a
relatively long-standing NCQ SSD corruption issue reported against
dm-crypt ever since the dm-crypt cpu parallelization patches were
merged back in 4.0.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWAbi6AAoJEMUj8QotnQNaevgH/RvtboJ1QrpyUtdG1FuWrbNb
ZBfVvq3EOdWtWYZKw57AgMMBvTtcTG94zxHJ2In919RF7oTdVATIo5PJK2aOVfIX
KiNuaypQAxL7ybQIAHsWbGihcOrLROMzJHkED2X2TKYnAnXhzthEGhGEmvsEOu5v
R5HmjI634Nv84kH87TO+tP+yFFDjDXaVdt3i5D2srT17SRFe/6WlEBKGshhXmavV
KHY7zibcfOXiMR01oCgpIoqwd3LUF1w4B+MQhMhF8cBOLF8r7DkMjdqvX0Xn/KVf
uhzanqGQsBP3aIY0f0+BlEm44+nvq1je7m6bxzRtxSMOcDJJMdEl1eDPYhC7wCM=
=/czf
-----END PGP SIGNATURE-----
Merge tag 'dm-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two stable@ fixes:
- DM thinp fix to properly advertise discard support as disabled for
thin devices backed by a thin-pool with discard support disabled.
- DM crypt fix to prevent the creation of bios that violate the
underlying block device's max_segments limits. This fixes a
relatively long-standing NCQ SSD corruption issue reported against
dm-crypt ever since the dm-crypt cpu parallelization patches were
merged back in 4.0"
* tag 'dm-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm crypt: constrain crypt device's max_segment_size to PAGE_SIZE
dm thin: disable discard support for thin devices if pool's is disabled
This fixes a duplicated pin control causing this error:
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already
requested by regulators:regulator@2; cannot claim for 2184000.usb
imx6q-pinctrl 20e0000.iomuxc: pin-137 (2184000.usb) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 137
(MX6Q_PAD_GPIO_1) from group usbotggrp on device 20e0000.iomuxc
imx_usb 2184000.usb: Error applying setting, reverse things
back
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_EIM_D31 already
requested by regulators:regulator@1; cannot claim for 2184200.usb
imx6q-pinctrl 20e0000.iomuxc: pin-52 (2184200.usb) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 52 (MX6Q_PAD_EIM_D31)
from group usbh1grp on device 20e0000.iomuxc
imx_usb 2184200.usb: Error applying setting, reverse things
back
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Fixes: e2047e33f2 ("ARM: dts: add initial Rex Pro board support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Tegra HD-audio controller driver causes deadlocks when loaded as a
module since the driver invokes request_module() at binding with the
codec driver. This patch works around it by deferring the probe in a
work like Intel HD-audio controller driver does. Although hovering
the codec probe stuff into udev would be a better solution, it may
cause other regressions, so let's try this band-aid fix until the more
proper solution gets landed.
Reported-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This change is needed to properly lock I2C bus driver, which serves DDC.
Prior to this change i2c_put_adapter() is misused, which may lead to
an overflow over zero of I2C bus driver user counter.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to X.Org driver, chips older than TGUI9660 have only 1 width bit
in AddColReg. Touching the 2nd one causes I2C/DDC to fail on TGUI9440.
Set only 1 bit of width in AddColReg on TGUI9440 and CYBER9320.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the kernel is compiled with -Os (CONFIG_CC_OPTIMIZE_FOR_SIZE), tridentfb
hangs the machine upon load with Blade3D cards unless acceleration is disabled.
This is caused by memcpy() which copies data byte-by-byte (rep movsb) when
compiled with -Os. The card does not like that - it requires 32-bit access.
Use iowrite_32() instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Jonathan Liu reports that the recent addition of CPU_SW_DOMAIN_PAN
causes wpa_supplicant to die due to the following kernel oops:
Unhandled fault: page domain fault (0x81b) at 0x001017a2
pgd = ee1b8000
[001017a2] *pgd=6ebee831, *pte=6c35475f, *ppte=6c354c7f
Internal error: : 81b [#1] SMP ARM
Modules linked in: rt2800usb rt2x00usb rt2800librt2x00lib crc_ccitt mac80211
CPU: 1 PID: 202 Comm: wpa_supplicant Not tainted 4.3.0-rc2 #1
Hardware name: Allwinner sun7i (A20) Family
task: ec872f80 ti: ee364000 task.ti: ee364000
PC is at do_alignment_ldmstm+0x1d4/0x238
LR is at 0x0
pc : [<c001d1d8>] lr : [<00000000>] psr: 600c0113
sp : ee365e18 ip : 00000000 fp : 00000002
r10: 001017a2 r9 : 00000002 r8 : 001017aa
r7 : ee365fb0 r6 : e8820018 r5 : 001017a2 r4 : 00000003
r3 : d49e30e0 r2 : 00000000 r1 : ee365fbc r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none[ 34.393106] Control: 10c5387d Table: 6e1b806a DAC: 00000051
Process wpa_supplicant (pid: 202, stack limit = 0xee364210)
Stack: (0xee365e18 to 0xee366000)
...
[<c001d1d8>] (do_alignment_ldmstm) from [<c001d510>] (do_alignment+0x1f0/0x904)
[<c001d510>] (do_alignment) from [<c00092a0>] (do_DataAbort+0x38/0xb4)
[<c00092a0>] (do_DataAbort) from [<c0013d7c>] (__dabt_usr+0x3c/0x40)
Exception stack(0xee365fb0 to 0xee365ff8)
5fa0: 00000000 56c728c0 001017a2 d49e30e0
5fc0: 775448d2 597d4e74 00200800 7a9e1625 00802001 00000021 b6deec84 00000100
5fe0: 08020200 be9f4f20 0c0b0d0a b6d9b3e0 600c0010 ffffffff
Code: e1a0a005 e1a0000c 1affffe8 e5913000 (e4ea3001)
---[ end trace 0acd3882fcfdf9dd ]---
This is caused by the alignment handler not being fixed up for the
uaccess changes, and userspace issuing an unaligned LDM instruction.
So, fix the problem by adding the necessary fixups.
Reported-by: Jonathan Liu <net147@gmail.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King
Linus Torvalds
Andy Shevchenko
Andrzej Hajda
Robert Jarzmik
Rafael J. Wysocki
Viresh Kumar
Olof Johansson
Benjamin Gaignard
Kishon Vijay Abraham I
Tony Lindgren
Matt Bennett
Lorenzo Pieralisi
Javier Martinez Canillas
David S. Miller
Wilson Kok
Sergei Shtylyov
Alex Williamson
Eric Dumazet
WANG Cong
Jiri Benc
Sudeep Holla
Pravin B Shelar
Dave Airlie
Tejun Heo
Herbert Xu
Takashi Iwai
Felipe F. Tonello
Vladimir Zapolskiy
Ondrej Zary
Luis de Bethencourt