The devm_pinctrl_register() function returns an error pointer or a valid
handle. So checking for NULL here is pointless and can never trigger.
Check the returned value with IS_ERR instead and propagate this value as
done in the other functions which call devm_pinctrl_register().
Fixes: 0751bb5c44 ("drm/tegra: dpaux: Add pinctrl support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX pins are shared with an internal I2C controller. To allow
these pins to be muxed to the I2C controller, register a pinctrl device
for the DPAUX device.
This is based upon work by Thierry Reding <treding@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To utilise the DPAUX on Tegra, the SOR power partition must be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework for DPAUX. However, the sequence
for gating/ungating the SOR power partition requires that the DPAUX
reset is asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the
DPAUX driver cannot request the same reset unless we mark the resets as
shared. Sharing resets will not work in this case because we cannot
guarantee that the reset will be asserted/de-asserted at the appropriate
time. Therefore, given that the Tegra generic PM domain code will handle
the DPAUX reset, do not request the reset in the DPAUX driver if the
DPAUX device has a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding pinctrl support for the DPAUX pads, add a
couple of helpers functions to configure the pads and control their
power.
Please note that although a simple if-statement could be used instead
of a case statement for configuring the pads as there are only two
possible modes, a case statement is used because when integrating with
the pinctrl framework, we need to be able to handle invalid modes that
could be passed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the probing of the DPAUX fails, then clocks are left enabled and the
DPAUX reset de-asserted. Add code to perform the necessary clean-up on
probe failure by disabling clocks and asserting the reset.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of getting a pointer to the driver-specific wrapper of AUX
channels, use the AUX channel objects directly to avoid hackish casting
between the two types.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A address-only I2C_WRITE can't be replied with a short i2c ack, but I
suppose it could be replied with an i2c defer. So the code should be
prepared for an address-only I2C_WRITE_STATUS_UPDATE.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the I2C_STATUS request to I2C_WRITE_STATUS_UPDATE to match the
spec.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DPAUX registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX read/write FIFO registers aren't sequential in the register
space, causing transfers larger than 4 bytes to cause accesses to non-
existing FIFO registers.
Fixes: 6b6b604215 ("drm/tegra: Add eDP support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.
Done using following cocci patch for each define:
@@
@@
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
...
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When tegra-drm.ko is built as a module, these MODULE_DEVICE_TABLEs allow
the module to be auto-loaded since the module will match the devices
instantiated from device tree.
(Notes for stable: in 3.14+, just git rm any conflicting file, since they
are added in later kernels. For 3.13 and below, manual merging will be
needed)
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Doing so allows the hotplug events generated by the connector to be
properly handled by the DRM poll helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Calling the drm_helper_hpd_irq_event() helper can sleep, so instead of
invoking it directly from the interrupt handler, schedule a work queue
and run it from there.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Certain types of I2C-over-AUX transactions require that only the address
is transferred. Detect this by looking at the AUX message's size and set
the address-only bit appropriately.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Christophe Jaillet
Jon Hunter
Thierry Reding
Ville Syrjälä
Sonika Jindal
Stephen Warren
Dave Airlie