Pointer cmpl used to iterate through completion entries is updated at
the beginning of while loop as well as at the end. The update at the end
of the loop is useless.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch converts kzalloc->copy_from_user sequence to memdup_user. There
is also one useless assignment of NULL to bnad->regdata as it is followed
by assignment of kzalloc output.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_E_PRIO_CHANGE event is never sent for bna_tx so it doesn't need to be
handled. After this change bna_tx->flags cannot contain
BNA_TX_F_PRIO_CHANGED flag and it can be also eliminated.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bna_rx_config struct member paused can be removed as it is never
written and as it cannot have non-zero value the bna_rxf struct member
flags also cannot have BNA_RXF_F_PAUSED value and is always zero.
So the flags member can be removed as well as bna_rxf_flags enum and
the code-paths that needs to have non-zero bna_rxf->flags.
This clean-up makes bna_rxf_sm_paused state unsed and can be also removed.
Signed-off-by: David S. Miller <davem@davemloft.net>
RXF_E_PAUSE & RXF_E_RESUME events are never sent for bna_rxf object so
they needn't to be handled. The bna_rxf's state bna_rxf_sm_fltr_clr_wait
and function bna_rxf_fltr_clear are unused after this so remove them also.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removed:
bna_rx_ucast_add
bna_rx_ucast_del
simplified:
bna_enet_pause_config
bna_rx_mcast_delall
bna_rx_mcast_listset
bna_rx_mode_set
bna_rx_ucast_listset
bna_rx_ucast_set
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch converts mac_t type to widely used 'u8 [ETH_ALEN]'.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameters of all ether_addr_copy instances were checked for proper
alignment. Alignment of bnad_bcast_addr is forced to 2 as the implicit
alignment is 1.
I have also renamed address parameter of bnad_set_mac_address() to addr.
The name mac_addr was a little bit confusing as the real parameter is
struct sockaddr *.
v2: added __aligned directive to bnad_bcast_addr, renamed parameter of
bnad_set_mac_address() (thx joe@perches.com)
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx5 Ethernet driver update - Jun 11 2015
This series from Saeed, Achiad and Gal contains few fixes
to the recently introduced mlx5 Ethernet functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and use transport domain by the Ethernet driver code.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each transport object, namely TIR and TIS, must have a transport domain
number (TDN) identifier.
The driver wrongly assumed that it is OK to use TDN=0 without explicit
TDN allocation from the device.
The TDN will also be used for isolating different processes once user
mode Ethernet will be supported.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NETIF_F_SG is set, each send WQE may have a different size since
each skb can have different number of fragments as of LSO header etc.
This implies that a given WQE may wrap around the send queue, i.e begin
at its end and continue at its start. While it is legal by the device spec,
we preferred a solution that avoids it - when building of current WQE is
done, if the next WQE may wrap around the send queue, fill the send queue
with NOPs WQEs till its end, so that the next WQE will begin at send queue
start.
NOP WQE for itself cannot wrap around the send queue since it is of
minimal size - 64 bytes, and all send WQEs are a multiple of that size.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet driver requires at least 3 flow table levels to
operate, enforce that.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to resolve a HW configuration issue for enabling HW CVLAN
insertion. Meanwhile, no need to implement the VLAN insertion in
the driver, rather use the generic kernel VLAN insertion method.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable HW cacheline start padding and align RX WQE size to cacheline
while considering HW start padding. Also, fix dma_unmap call to use
the correct SKB data buffer size.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we configured HW MTU to be netdev->mtu, actually we
need to configure netdev->mtu + (ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN).
Also, query MTU can not fail, hence make the relevant helper a
void functionm, add mlx5e_set_dev_port_mtu, helper function to
handle MTU setting.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return success if mlx5e_alloc_sq_db() fails but we should return an
error code.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DEBUG preprocessor macro is defined the ps3_gelic_net driver build
fails due to an undeclared routine gelic_descr_get_status(). This problem
was introduced during the code cleanup of commit
6b0c21cede (net: Fix p3_gelic_net sparse warnings),
which re-arranged the ordering of some of the gelic routines.
This change just moves the gelic_descr_get_status() routine up in the
ps3_gelic_net.c source file. There is no functional change.
Fixes build errors like these:
drivers/net/ethernet/toshiba/ps3_gelic_net.c: error: implicit declaration of function gelic_descr_get_status
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add strings array of the current supported tunable options.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: broadcom MDIO support for broken turn-around
These two patches update the GENET and UniMAC MDIO controllers to deal with
PHYs that are known to have a broken turn-around bug (e.g: BCM53125 and others)
This utilizes the infrastructure that code recently added to do that in 'net-next'.
Note that the changes look nearly identical and I will try to address the MDIO
code duplication between GENET and UniMAC in a future patch series.
Changes in v2:
- remove brcmphy.h include in mdio-bcm-unimac.c
- use the same comment as with GENET's MDIO read function
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHYs/switches such as Broadcom's BCM53125 have a hardware bug
which makes them not release the MDIO line during turn-around time. This gets
flagged by the UniMAC MDIO controller as a read failure, and we fail the read
transaction.
Check the MDIO bus phy_ignore_ta_mask bitmask for the PHY we are reading
from and if it is listed in this bitmask, ignore the read failure and
proceed with returning the data we read out of the controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHYs/switches such as Broadcom's BCM53125 have a hardware
bug which makes them not release the MDIO line during turn-around time.
This gets flagged by the GENET MDIO controller as a read failure, and we
fail the read transaction.
Check the MDIO bus phy_ignore_ta_mask bitmask for the PHY we are reading
from and if it is listed in this bitmask, ignore the read failure and
proceed with returning the data we read out of the controller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHY IDs for Davicom DM9161B and DM9161C variants.
Tested with a DM9161C on a custom Atmel-based SAM9X25 board in RMII
mode.
The DM9161B uses the same model id with just the LSB bit of the version
id changing (which is masked out).
For all intents and purposes they're the same as the DM9161A with an
added GPSI mode and better fabrication process.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB device includes the gPTP timer, so we can implement a PTP clock
driver. We're doing that in a separate file, with the main Ethernet driver
calling the PTP driver's [de]initialization and interrupt handler functions.
Unfortunately, the clock seems tightly coupled with the AVB-DMAC, so when that
one leaves the operation mode, we have to unregister the PTP clock... :-(
Based on the original patches by Masaru Nagai.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet AVB includes an Gigabit Ethernet controller (E-MAC) that is basically
compatible with SuperH Gigabit Ethernet E-MAC. Ethernet AVB has a dedicated
direct memory access controller (AVB-DMAC) that is a new design compared to the
SuperH E-DMAC. The AVB-DMAC is compliant with 3 standards formulated for IEEE
802.1BA: IEEE 802.1AS timing and synchronization protocol, IEEE 802.1Qav real-
time transfer, and the IEEE 802.1Qat stream reservation protocol.
The driver only supports device tree probing, so the binding document is
included in this patch.
Based on the original patches by Mitsuhiro Kimura.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAIA Delay-Gradient (CDG) is a TCP congestion control that modifies
the TCP sender in order to [1]:
o Use the delay gradient as a congestion signal.
o Back off with an average probability that is independent of the RTT.
o Coexist with flows that use loss-based congestion control, i.e.,
flows that are unresponsive to the delay signal.
o Tolerate packet loss unrelated to congestion. (Disabled by default.)
Its FreeBSD implementation was presented for the ICCRG in July 2012;
slides are available at http://www.ietf.org/proceedings/84/iccrg.html
Running the experiment scenarios in [1] suggests that our implementation
achieves more goodput compared with FreeBSD 10.0 senders, although it also
causes more queueing delay for a given backoff factor.
The loss tolerance heuristic is disabled by default due to safety concerns
for its use in the Internet [2, p. 45-46].
We use a variant of the Hybrid Slow start algorithm in tcp_cubic to reduce
the probability of slow start overshoot.
[1] D.A. Hayes and G. Armitage. "Revisiting TCP congestion control using
delay gradients." In Networking 2011, pages 328-341. Springer, 2011.
[2] K.K. Jonassen. "Implementing CAIA Delay-Gradient in Linux."
MSc thesis. Department of Informatics, University of Oslo, 2015.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming tcp_cdg uses tcp_enter_cwr() to initiate PRR. Export this
function so that CDG can be compiled as a module.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: David Hayes <davihay@ifi.uio.no>
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu>
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_SWITCHDEV is enabled, but port driver does not implement
support for IPv4 FIB add/del ops, don't fail route add/del offload
operations. Route adds will not be marked as OFFLOAD. Routes will be
installed in the kernel FIB, as usual.
This was report/fixed by Florian when testing DSA driver with net-next on
devices with L2 offload support but no L3 offload support. What he reported
was an initial route installed from DHCP client would fail (route not
installed to kernel FIB). This was triggering the setting of
ipv4.fib_offload_disabled, which would disable route offloading after the
first failure. So subsequent attempts to install the route would succeed.
There is follow-on work/discussion to address the handling of route install
failures, but for now, let's differentiate between no support and failed
support.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: broadcom: define pseudo-PHY address
This patch series converts existing in-tree users of the Broadcom pseudo-PHY
address (30) used to configure MDIO-connected switches to share a constant in a
shared header files.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the newly introduced BRCM_PSEUDO_PHY_ADDR constant from
brcmphy.h instead of open-coding the Broadcom Ethernet switches
pseudo-PHY address (30).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What BGMAC defines as BGMAC_PHY_NOREGS is in fact the Broadcom Ethernet
switches' pseudo-PHY address (30), utilize the newly introduced constant
from brcmphy.h
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What B44 has been locally using as B44_PHY_ADDR_NO_LOCAL_PHY is in fact
the Broadcom Ethernet switches pseudo-PHY address (30). Update the
header to use the newly introduced constant and update comments so they
are within 80 columns and consistent.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the pseudo-PHY address (30) which is used by all Broadcom
Ethernet switches in a shared header file.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We utilize inline functions from the PHY library, make sure that we do
include phy.h in brcmphy.h in order for the code including brcmphy.h not
to have to resolve this inclusion dependency.
Fixes: 705314797b ("net: phy: broadcom: move shadow 0x1C register accessors to brcmphy.h")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dctcp_alpha can be read by from dctcp_get_info() without
synchro, so use WRITE_ONCE() to prevent compiler from using
dctcp_alpha as a temporary variable.
Also, playing with small dctcp_shift_g (like 1), can expose
an overflow with 32bit values shifted 9 times before divide.
Use an u64 field to avoid this problem, and perform the divide
only if acked_bytes_ecn is not zero.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJVeEQ1AAoJEDBSmw7B7bqrebcP/3v7I2ZXAeHag2W4hdD4YH6W
tuKfs3JKW3GDh84l2AJs2JBpFxR6Tk0Z7zGKrPLzkBTkkJkSLgKuUKR0+YQU6PYH
VfZ2NkdIHEqouLgMWxGGlp6suqp2yYD9tiIUroICXZ6aFm5trQuZgzv5ePI+lhmX
cWUYCawE2tcpVdg0NJsFExeCJhw81e/Bet1LCGHo0asWNpIK7phMdltzD7e4tgQS
4q475FCIkWxbxKgJRrRkz8J7grsjK1wf2W3acOxKMaoVBeqJVW5BWDrTgo0aDPts
qQ8n8t1s9o/jKQIvaz3RyjkQgX8T4vCMqkouLF4jJOThKIsUSi3Fvm9oKcMg4YhA
Ju5QWfbCBFhpLZeBzWzKyePTnDru1XDFFVdIATLONKTVg1modzFAs3j5gb4Z3Wtg
VYLoLWWpRtHKd9pzfZMhyWq64Xb8C+qlyQHr4r4QRm9ADz0Jq+OCh0rTFt+/bncM
CHxnf0VS9hEOFk0+TxFqi2yXOnv2uMgcN+jnGkEs4QuLfv9ML1Eb23ZjDoHxd1uq
1Yd4R8IDEY/KU6UJMwksz+gV/ekoB32eAhw56pxehgAMuZL4OgNvmeAQHx7Jq9it
0/OfAK2BSNH8odqYQbpg89C8keqSInMwUhFyRhyMJAWSKiPRHypsDBWxMKGJIssI
3mB4d/go+RP1AvZnazeF
=2wTw
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For this round we mostly have fixes:
* mesh fixes from Alexis Green and Chun-Yeow Yeoh,
* a documentation fix from Jakub Kicinski,
* a missing channel release (from Michal Kazior),
* a fix for a signal strength reporting bug (from Sara Sharon),
* handle deauth while associating (myself),
* don't report mangled TX SKB back to userspace for status (myself),
* handle aggregation session timeouts properly in fast-xmit (myself)
However, there are also a few cleanups and one big change that
affects all drivers (and that required me to pull in your tree)
to change the mac80211 HW flags to use an unsigned long bitmap
so that we can extend them more easily - we're running out of
flags even with a cleanup to remove the two unused ones.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SCM_SECURITY was originally only implemented for datagram sockets,
not for stream sockets. However, SCM_CREDENTIALS is supported on
Unix stream sockets. For consistency, implement Unix stream support
for SCM_SECURITY as well. Also clean up the existing code and get
rid of the superfluous UNIXSID macro.
Motivated by https://bugzilla.redhat.com/show_bug.cgi?id=1224211,
where systemd was using SCM_CREDENTIALS and assumed wrongly that
SCM_SECURITY was also supported on Unix stream sockets.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e1, e2, a;
@@
-init_timer(&e1);
+setup_timer(&e1, a, 0UL);
... when != a = e2
-e1.function = a;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera
David S. Miller
Achiad Shochat
Saeed Mahameed
Gal Pressman
Dan Carpenter
Fabian Frederick
Geoff Levand
Hadar Hen Zion
Florian Fainelli
Gustavo Zacarias
Sergei Shtylyov
Kenneth Klette Jonassen
Scott Feldman
Eric Dumazet
Stephen Smalley
Vaishali Thakkar