When a targetport is removed from the config, fcloop will avoid calling
the LS done() routine thinking the targetport is gone. This leaves the
initiator reset/reconnect hanging as it waits for a status on the
Create_Association LS for the reconnect.
Change the filter in the LS callback path. If tport null (set when
failed validation before "sending to remote port"), be sure to call
done. This was the main bug. But, continue the logic that only calls
done if tport was set but there is no remoteport (e.g. case where
remoteport has been removed, thus host doesn't expect a completion).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In many architectures loads may be reordered with older stores to
different locations. In the nvme driver the following two operations
could be reordered:
- Write shadow doorbell (dbbuf_db) into memory.
- Read EventIdx (dbbuf_ei) from memory.
This can result in a potential race condition between driver and VM host
processing requests (if given virtual NVMe controller has a support for
shadow doorbell). If that occurs, then the NVMe controller may decide to
wait for MMIO doorbell from guest operating system, and guest driver may
decide not to issue MMIO doorbell on any of subsequent commands.
This issue is purely timing-dependent one, so there is no easy way to
reproduce it. Currently the easiest known approach is to run "Oracle IO
Numbers" (orion) that is shipped with Oracle DB:
orion -run advanced -num_large 0 -size_small 8 -type rand -simulate \
concat -write 40 -duration 120 -matrix row -testname nvme_test
Where nvme_test is a .lun file that contains a list of NVMe block
devices to run test against. Limiting number of vCPUs assigned to given
VM instance seems to increase chances for this bug to occur. On test
environment with VM that got 4 NVMe drives and 1 vCPU assigned the
virtual NVMe controller hang could be observed within 10-20 minutes.
That correspond to about 400-500k IO operations processed (or about
100GB of IO read/writes).
Orion tool was used as a validation and set to run in a loop for 36
hours (equivalent of pushing 550M IO operations). No issues were
observed. That suggest that the patch fixes the issue.
Fixes: f9f38e3338 ("nvme: improve performance for virtual NVMe devices")
Signed-off-by: Michal Wnukowski <wnukowski@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
[hch: updated changelog and comment a bit]
Signed-off-by: Christoph Hellwig <hch@lst.de>
rdma.git merge resolution for the 4.19 merge window
Conflicts:
drivers/infiniband/core/rdma_core.c
- Use the rdma code and revise with the new spelling for
atomic_fetch_add_unless
drivers/nvme/host/rdma.c
- Replace max_sge with max_send_sge in new blk code
drivers/nvme/target/rdma.c
- Use the blk code and revise to use NULL for ib_post_recv when
appropriate
- Replace max_sge with max_recv_sge in new blk code
net/rds/ib_send.c
- Use the net code and revise to use NULL for ib_post_recv when
appropriate
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltwm2geHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGITkH/iSzkVhT2OxHoir0
mLVzTi7/Z17L0e/ELl7TvAC0iLFlWZKdlGR0g3b4/QpXLPmNK4HxiDRTQuWn8ke0
qDZyDq89HqLt+mpeFZ43PCd9oqV8CH2xxK3iCWReqv6bNnowGnRpSStlks4rDqWn
zURC/5sUh7TzEG4s997RrrpnyPeQWUlf/Mhtzg2/WvK2btoLWgu5qzjX1uFh3s7u
vaF2NXVJ3X03gPktyxZzwtO1SwLFS1jhwUXWBZ5AnoJ99ywkghQnkqS/2YpekNTm
wFk80/78sU+d91aAqO8kkhHj8VRrd+9SGnZ4mB2aZHwjZjGcics4RRtxukSfOQ+6
L47IdXo=
=sJkt
-----END PGP SIGNATURE-----
Merge tag 'v4.18' into rdma.git for-next
Resolve merge conflicts from the -rc cycle against the rdma.git tree:
Conflicts:
drivers/infiniband/core/uverbs_cmd.c
- New ifs added to ib_uverbs_ex_create_flow in -rc and for-next
- Merge removal of file->ucontext in for-next with new code in -rc
drivers/infiniband/core/uverbs_main.c
- for-next removed code from ib_uverbs_write() that was modified
in for-rc
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
-----BEGIN PGP SIGNATURE-----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=b9ib
-----END PGP SIGNATURE-----
Merge tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"First pull request for this merge window, there will also be a
followup request with some stragglers.
This pull request contains:
- Fix for a thundering heard issue in the wbt block code (Anchal
Agarwal)
- A few NVMe pull requests:
* Improved tracepoints (Keith)
* Larger inline data support for RDMA (Steve Wise)
* RDMA setup/teardown fixes (Sagi)
* Effects log suppor for NVMe target (Chaitanya Kulkarni)
* Buffered IO suppor for NVMe target (Chaitanya Kulkarni)
* TP4004 (ANA) support (Christoph)
* Various NVMe fixes
- Block io-latency controller support. Much needed support for
properly containing block devices. (Josef)
- Series improving how we handle sense information on the stack
(Kees)
- Lightnvm fixes and updates/improvements (Mathias/Javier et al)
- Zoned device support for null_blk (Matias)
- AIX partition fixes (Mauricio Faria de Oliveira)
- DIF checksum code made generic (Max Gurtovoy)
- Add support for discard in iostats (Michael Callahan / Tejun)
- Set of updates for BFQ (Paolo)
- Removal of async write support for bsg (Christoph)
- Bio page dirtying and clone fixups (Christoph)
- Set of bcache fix/changes (via Coly)
- Series improving blk-mq queue setup/teardown speed (Ming)
- Series improving merging performance on blk-mq (Ming)
- Lots of other fixes and cleanups from a slew of folks"
* tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block: (190 commits)
blkcg: Make blkg_root_lookup() work for queues in bypass mode
bcache: fix error setting writeback_rate through sysfs interface
null_blk: add lock drop/acquire annotation
Blk-throttle: reduce tail io latency when iops limit is enforced
block: paride: pd: mark expected switch fall-throughs
block: Ensure that a request queue is dissociated from the cgroup controller
block: Introduce blk_exit_queue()
blkcg: Introduce blkg_root_lookup()
block: Remove two superfluous #include directives
blk-mq: count the hctx as active before allocating tag
block: bvec_nr_vecs() returns value for wrong slab
bcache: trivial - remove tailing backslash in macro BTREE_FLAG
bcache: make the pr_err statement used for ENOENT only in sysfs_attatch section
bcache: set max writeback rate when I/O request is idle
bcache: add code comments for bset.c
bcache: fix mistaken comments in request.c
bcache: fix mistaken code comments in bcache.h
bcache: add a comment in super.c
bcache: avoid unncessary cache prefetch bch_btree_node_get()
bcache: display rate debug parameters to 0 when writeback is not running
...
When the user supplies a ctrl_loss_tmo < 0, we warn them that this will
cause the fabrics layer to attempt reconnection forever. However, in
reality the fabrics layer never attempts to reconnect because the
condition to test whether we should reconnect is backwards in this case.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch implements the Namespace Write Protect feature described in
"NVMe TP 4005a Namespace Write Protect". In this version, we implement
No Write Protect and Write Protect states for target ns which can be
toggled by set-features commands from the host side.
For write-protect state transition, we need to flush the ns specified
as a part of command so we also add helpers for carrying out synchronous
flush operations.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[hch: fixed an incorrect endianess conversion, minor cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
NVMe 1.3 TP 4005 introduces new filed (NSATTR). This field indicates
whether given namespace is write protected or not. This patch sets the
gendisk associated with the namespace to read only based on the identify
namespace nsattr field.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When the initial discovery fails the subsystem hasn't been setup yet
in nvme_mpath_stop, and we can't dereference ctrl->subsys.
Fixes: 0d0b660f ("nvme: add ANA support")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A minor version number increase should not break backwards
compatibility.
Fixes: 3cb98f84d3 ("lightnvm: add minor version to generic geometry")
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe changes from Christoph:
"This contains the support for TP4004, Asymmetric Namespace Access,
which makes NVMe multipathing usable in practice."
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvmet: use Retain Async Event bit to clear AEN
nvmet: support configuring ANA groups
nvmet: add minimal ANA support
nvmet: track and limit the number of namespaces per subsystem
nvmet: keep a port pointer in nvmet_ctrl
nvme: add ANA support
nvme: remove nvme_req_needs_failover
nvme: simplify the API for getting log pages
nvme.h: add ANA definitions
nvme.h: add support for the log specific field
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltU8z0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5X8H/2fJr7m3k242+t76
sitwvx1eoPqTgryW59dRKm9IuXAGA+AjauvHzaz1QxomeQa50JghGWefD0eiJfkA
1AphQ/24EOiAbbVk084dAI/C2p122dE4D5Fy7CrfLnuouyrbFaZI5STbnrRct7sR
9deeYW0GDHO1Uenp4WDCj0baaqJqaevZ+7GG09DnWpya2nQtSkGBjqn6GpYmrfOU
mqFuxAX8mEOW6cwK16y/vYtnVjuuMAiZ63/OJ8AQ6d6ArGLwAsdn7f8Fn4I4tEr2
L0d3CRLUyegms4++Dmlu05k64buQu46WlPhjCZc5/Ts4kjrNxBuHejj2/jeSnUSt
vJJlibI=
=42a5
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rc6' into for-4.19/block2
Pull in 4.18-rc6 to get the NVMe core AEN change to avoid a
merge conflict down the line.
Signed-of-by: Jens Axboe <axboe@kernel.dk>
Also moved the logic of the remapping to the nvme core driver instead
of implementing it in the nvme pci driver. This way all the other nvme
transport drivers will benefit from it (in case they'll implement metadata
support).
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently this function is implemented in the scsi layer, but it's
actual place should be the block layer since T10-PI is a general
data integrity feature that is used in the nvme protocol as well.
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=2ogY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180727' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Bigger than usual at this time, mostly due to the O_DIRECT corruption
issue and the fact that I was on vacation last week. This contains:
- NVMe pull request with two fixes for the FC code, and two target
fixes (Christoph)
- a DIF bio reset iteration fix (Greg Edwards)
- two nbd reply and requeue fixes (Josef)
- SCSI timeout fixup (Keith)
- a small series that fixes an issue with bio_iov_iter_get_pages(),
which ended up causing corruption for larger sized O_DIRECT writes
that ended up racing with buffered writes (Martin Wilck)"
* tag 'for-linus-20180727' of git://git.kernel.dk/linux-block:
block: reset bi_iter.bi_done after splitting bio
block: bio_iov_iter_get_pages: pin more pages for multi-segment IOs
blkdev: __blkdev_direct_IO_simple: fix leak in error case
block: bio_iov_iter_get_pages: fix size of last iovec
nvmet: only check for filebacking on -ENOTBLK
nvmet: fixup crash on NULL device path
scsi: set timed out out mq requests to complete
blk-mq: export setting request completion state
nvme: if_ready checks to fail io to deleting controller
nvmet-fc: fix target sgl list on large transfers
nbd: handle unexpected replies better
nbd: don't requeue the same request twice.
In the current implementation, we clear the AEN bit when we get the
"get log page" command if given log page is associated with AEN.
This patch allows optionally retaining the AEN for the ctrl
under consideration when Retain Asynchronous Event (RAE) bit is set
as a part of "get log page" command.
This allows the host to read the Log page and optionally retaining the
AEN associated with this log page when using userspace tools like
nvme-cli.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[hch: also use the new helper in the just merged ANA code]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Allow creating non-default ANA groups (group ID > 1). Groups are created
either by assigning the group ID to a namespace, or by creating a configfs
group object under a specific port. All namespaces assigned to a group
that doesn't have a configfs object for a given port are marked as
inaccessible.
Allow changing the ANA state on a per-port basis by creating an
ana_groups directory under each port, and another directory with an
ana_state file in it. The default ANA group 1 directory is created
automatically for each port.
For all changes in ANA configuration the ANA change AEN is sent. We only
keep a global changecount instead of additional per-group changecounts to
keep the implementation as simple as possible.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Add support for Asynchronous Namespace Access as specified in NVMe 1.3
TP 4004.
Just add a default ANA group 1 that is optimized on all ports. This is
(and will remain) the default assignment for any namespace not epxlicitly
assigned to another ANA group. The ANA state can be manually changed
through the configfs interface, including the change state.
Includes fixes and improvements from Hannes Reinecke.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
TP 4004 introduces a new 'Maximum Number of Allocated Namespaces' field
in the Identify controller data to help the host size resources. Put
an upper limit on the supported namespaces to be able to support this
value as supporting 32-bits worth of namespaces would lead to very
large buffers. The limit is completely arbitrary at this point.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
This will be needed for the ANA AEN code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Add support for Asynchronous Namespace Access as specified in NVMe 1.3
TP 4004. With ANA each namespace attached to a controller belongs to an
ANA group that describes the characteristics of accessing the namespaces
through this controller. In the optimized and non-optimized states
namespaces can be accessed regularly, although in a multi-pathing
environment we should always prefer to access a namespace through a
controller where an optimized relationship exists. Namespaces in
Inaccessible, Permanent-Loss or Change state for a given controller
should not be accessed.
The states are updated through reading the ANA log page, which is read
once during controller initialization, whenever the ANA change notice
AEN is received, or when one of the ANA specific status codes that
signal a state change is received on a command.
The ANA state is kept in the nvme_ns structure, which makes the checks in
the fast path very simple. Updating the ANA state when reading the log
page is also very simple, the only downside is that finding the initial
ANA state when scanning for namespaces is a bit cumbersome.
The gendisk for a ns_head is only registered once a live path for it
exists. Without that the kernel would hang during partition scanning.
Includes fixes and improvements from Hannes Reinecke.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Now that we just call out to blk_path_error there isn't really any good
reason to not merge it into the only caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Merge nvme_get_log and nvme_get_log_ext into a single helper, which takes
a plain nsid instead of the nvme_ns pointer. Also add support for the
log specific field while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
We only need to check for a file-backed namespace if
nvmet_bdev_ns_enable() returns -ENOTBLK. For any other error
it's pointless as the open() error will remain the same.
Fixes: d5eff33e ("nvmet: add simple file backed ns support")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When writing an empty string into the device_path attribute the kernel
will crash with
nvmet: failed to open block device (null): (-22)
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
This patch sanitizes the error handling for invalid device path settings.
Fixes: a07b4970 ("nvmet: add a generic NVMe target")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of declaring and passing a dummy 'bad_wr' pointer, pass NULL
as third argument to ib_post_(send|recv|srq_recv)().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Instead of declaring and passing a dummy 'bad_wr' pointer, pass NULL
as third argument to ib_post_(send|recv|srq_recv)().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Don't use sizeof(uuid_le) where none of the parameters is type of uuid_le.
Since both arguments are u8 [16], use size of destination there.
Moreover, uuid_le is a deprecated type, and nvmet is using uuid_t
already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We follow the same queue teardown sequence in delete, reset and error
recovery. Centralize the logic. This patch does not change any
functionality.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Centralize controller sequence to a single routine that correctly cleans
up after failures instead of having multiple apperances in several flows
(create, reset, reconnect).
One thing that we also gain here are the sanity/boundary checks also
when connecting back to a dynamic controller.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the controller is going away, we need to unquiesce the IO queues so
that all pending request can fail gracefully before moving forward with
controller deletion. Do that before we destroy the IO queues so
blk_cleanup_queue won't block in freeze.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This will print the disk name to the nvme event trace for io requests so
a user can better distinguish traffic to different disks. This can be used
to create disk based filters. For example, to see only nvme0n2 traffic:
echo "disk == \"nvme0n2\"" > /sys/kernel/debug/tracing/events/nvme/filter
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
[hch: turned __assign_disk_name into an inline function]
Signed-off-by: Christoph Hellwig <hch@lst.de>
This appends the controller instance to the nvme trace buffer to
distinguish which controller is dispatching and completing a command.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The revised if_ready checks skipped over the case of returning error when
the controller is being deleted. Instead it was returning BUSY, which
caused the ios to retry, which caused the ns delete to hang waiting for
the ios to drain.
Stack trace of hang looks like:
kworker/u64:2 D 0 74 2 0x80000000
Workqueue: nvme-delete-wq nvme_delete_ctrl_work [nvme_core]
Call Trace:
? __schedule+0x26d/0x820
schedule+0x32/0x80
blk_mq_freeze_queue_wait+0x36/0x80
? remove_wait_queue+0x60/0x60
blk_cleanup_queue+0x72/0x160
nvme_ns_remove+0x106/0x140 [nvme_core]
nvme_remove_namespaces+0x7e/0xa0 [nvme_core]
nvme_delete_ctrl_work+0x4d/0x80 [nvme_core]
process_one_work+0x160/0x350
worker_thread+0x1c3/0x3d0
kthread+0xf5/0x130
? process_one_work+0x350/0x350
? kthread_bind+0x10/0x10
ret_from_fork+0x1f/0x30
Extend nvmf_fail_nonready_command() to supply the controller pointer so
that the controller state can be looked at. Fail any io to a controller
that is deleting.
Fixes: 3bc32bb118 ("nvme-fabrics: refactor queue ready check")
Fixes: 35897b920c ("nvme-fabrics: fix and refine state checks in __nvmf_check_ready")
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
The existing code to carve up the sg list expected an sg element-per-page
which can be very incorrect with iommu's remapping multiple memory pages
to fewer bus addresses. To hit this error required a large io payload
(greater than 256k) and a system that maps on a per-page basis. It's
possible that large ios could get by fine if the system condensed the
sgl list into the first 64 elements.
This patch corrects the sg list handling by specifically walking the
sg list element by element and attempting to divide the transfer up
on a per-sg element boundary. While doing so, it still tries to keep
sequences under 256k, but will exceed that rule if a single sg element
is larger than 256k.
Fixes: 48fa362b6c ("nvmet-fc: simplify sg list handling")
Cc: <stable@vger.kernel.org> # 4.14
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We can not match a command to its completion based on the command
id alone. We need the submitting queue identifier to pair with the
completion, so this patch adds that to the trace buffer.
This patch is also collapsing the admin and IO submission traces into a
single one so we don't need to duplicate this and creating unnecessary
code branches: we know if the command is an admin vs IO based on the qid.
And since we're here, the patch fixes code formatting in the area.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
[hch: move the qid helper to nvme.h and made it an inline function]
Signed-off-by: Christoph Hellwig <hch@lst.de>
We will need to reference the controller in the setup and completion
time for tracing and future traffic based keep alive support.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Posting receive buffer operation can fail, thus we should make
sure to have an error flow during initialization phase. While
we're here, add a debug print in case of a failure.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
ib_post_send operation should succeed unless something unusual
happened to the ib device.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The patch enables inline data sizes using up to 4 recv sges, and capping
the size at 16KB or at least 1 page size. So on a 4K page system, up to
16KB is supported, and for a 64K page system 1 page of 64KB is supported.
We avoid > 0 order page allocations for the inline buffers by using
multiple recv sges, one for each page. If the device cannot support
the configured inline data size due to lack of enough recv sges, then
log a warning and reduce the inline size.
Add a new configfs port attribute, called param_inline_data_size,
to allow configuring the size of inline data for a given nvmf port.
The maximum size allowed is still enforced by nvmet-rdma with
NVMET_RDMA_MAX_INLINE_DATA_SIZE, which is now max(16KB, PAGE_SIZE).
And the default size, if not specified via configfs, is still PAGE_SIZE.
This preserves the existing behavior, but allows larger inline sizes
for small page systems. If the configured inline data size exceeds
NVMET_RDMA_MAX_INLINE_DATA_SIZE, a warning is logged and the size is
reduced. If param_inline_data_size is set to 0, then inline data is
disabled for that nvmf port.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Allow up to 4 segments of inline data for NVMF WRITE operations. This
reduces latency for small WRITEs by removing the need for the target to
issue a READ WR for IB, or a REG_MR + READ WR chain for iWarp.
Also cap the inline segments used based on the limitations of the
device.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a new "buffered_io" attribute, which disabled direct I/O and thus
enables page cache based caching when enabled. The attribute can only
be changed when the namespace is disabled as the file has to be reopend
for the change to take effect.
The possibly blocking read/write are deferred to a newly introduced
global workqueue.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for Commands Supported and Effects log page
(Log Identifier 05h) for NVMeOF. This also makes it easier to find
which commands are supported, e.g. :-
subnqn : testnqn1
Admin Command Set
ACS2 [Get Log Page ] 00000001
ACS6 [Identify ] 00000001
ACS8 [Abort ] 00000001
ACS9 [Set Features ] 00000001
ACS10 [Get Features ] 00000001
ACS12 [Asynchronous Event Request ] 00000001
ACS24 [Keep Alive ] 00000001
NVM Command Set
IOCS0 [Flush ] 00000001
IOCS1 [Write ] 00000001
IOCS2 [Read ] 00000001
IOCS8 [Write Zeroes ] 00000001
IOCS9 [Dataset Management ] 00000001
This partticular functionality can be used from the host side to examine
the NVMeOF ctrl commands supported.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, the code initializes the keep alive work item whenever
nvme_start_keep_alive() is called. However, this routine is called
several times while reconnecting, etc. Although it's hoped that keep
alive is always disabled and not scheduled when start is called,
re-initing if it were scheduled or completing can have very bad
side effects. There's no need for re-initialization.
Move the keep_alive work item and cmd struct initialization to
controller init.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The old code in nvme_user_cmd() passed the userspace virtual address
from nvme_passthru_cmd.metadata as the length of the metadata buffer
as well as the address to nvme_submit_user_cmd().
Fixes: 63263d60 ("nvme: Use metadata for passthrough commands")
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Avoid excuting set_feature command if there is no supported bit in
Optional Asynchronous Events Supported (OAES).
Fixes: c0561f82 ("nvme: submit AEN event configuration on startup")
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Weiping Zhang <zhangweiping@didichuxing.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Chaitanya Kulkarni
James Smart
Michal Wnukowski
Jason Gunthorpe
Linus Torvalds
Tal Shorer
Hannes Reinecke
Matias Bjørling
Jens Axboe
Max Gurtovoy
Christoph Hellwig
Bart Van Assche
Andy Shevchenko
Sagi Grimberg
Gustavo A. R. Silva
Keith Busch
Steve Wise
Roland Dreier
Weiping Zhang