Krzysztof Helt found MTRR is not detected on k6-2
root cause:
we moved mtrr_bp_init() early for mtrr trimming,
and in early_detect we only read the CPU capability from cpuid,
so some cpu doesn't have that bit in cpuid.
So we need to add early_init_xxxx to preset those bit before mtrr_bp_init
for those earlier cpus.
this patch is for v2.6.27
Reported-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move early cpu initialization after cpu early get cap so the
early cpu initialization can fix up cpu caps.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current check for monotonicity is way too weak: Andreas Mohr reports (
http://lkml.org/lkml/2008/8/10/77 ) that on one of his test systems the
current check only triggers in 50% of all cases, leading to catastrophic
timer behaviour. To fix this issue, expand the check for monotonicity by
doing ten consecutive tests instead of one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On all hardware (some Intel ICH4, PIIX4 and PIIX4E chipsets) affected by a
hardware errata there's about a 4.2% chance that initialization of the
ACPI PMTMR fails. On those chipsets, we need to read out the timer value
at least three times to get a correct result, for every once in a while
(i.e. within a 3 ns window every 69.8 ns) the read returns a bogus
result. During normal operation we work around this issue, but during
initialization reading a bogus value may lead to -EINVAL even though the
hardware is usable.
Thanks to Andreas Mohr for spotting this issue.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have a bug in the calculation of the next jiffie to trigger the RTC
synchronisation. The aim here is to run sync_cmos_clock() as close as
possible to the middle of a second. Which means we want this function to
be called less than or equal to half a jiffie away from when now.tv_nsec
equals 5e8 (500000000).
If this is not the case for a given call to the function, for this purpose
instead of updating the RTC we calculate the offset in nanoseconds to the
next point in time where now.tv_nsec will be equal 5e8. The calculated
offset is then converted to jiffies as these are the unit used by the
timer.
Hovewer timespec_to_jiffies() used here uses a ceil()-type rounding mode,
where the resulting value is rounded up. As a result the range of
now.tv_nsec when the timer will trigger is from 5e8 to 5e8 + TICK_NSEC
rather than the desired 5e8 - TICK_NSEC / 2 to 5e8 + TICK_NSEC / 2.
As a result if for example sync_cmos_clock() happens to be called at the
time when now.tv_nsec is between 5e8 + TICK_NSEC / 2 and 5e8 to 5e8 +
TICK_NSEC, it will simply be rescheduled HZ jiffies later, falling in the
same range of now.tv_nsec again. Similarly for cases offsetted by an
integer multiple of TICK_NSEC.
This change addresses the problem by subtracting TICK_NSEC / 2 from the
nanosecond offset to the next point in time where now.tv_nsec will be
equal 5e8, effectively shifting the following rounding in
timespec_to_jiffies() so that it produces a rounded-to-nearest result.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch provides an ARM implementation of ioremap_wc().
We use different page table attributes depending on which CPU we
are running on:
- Non-XScale ARMv5 and earlier systems: The ARMv5 ARM documents four
possible mapping types (CB=00/01/10/11). We can't use any of the
cached memory types (CB=10/11), since that breaks coherency with
peripheral devices. Both CB=00 and CB=01 are suitable for _wc, and
CB=01 (Uncached/Buffered) allows the hardware more freedom than
CB=00, so we'll use that.
(The ARMv5 ARM seems to suggest that CB=01 is allowed to delay stores
but isn't allowed to merge them, but there is no other mapping type
we can use that allows the hardware to delay and merge stores, so
we'll go with CB=01.)
- XScale v1/v2 (ARMv5): same as the ARMv5 case above, with the slight
difference that on these platforms, CB=01 actually _does_ allow
merging stores. (If you want noncoalescing bufferable behavior
on Xscale v1/v2, you need to use XCB=101.)
- Xscale v3 (ARMv5) and ARMv6+: on these systems, we use TEXCB=00100
mappings (Inner/Outer Uncacheable in xsc3 parlance, Uncached Normal
in ARMv6 parlance).
The ARMv6 ARM explicitly says that any accesses to Normal memory can
be merged, which makes Normal memory more suitable for _wc mappings
than Device or Strongly Ordered memory, as the latter two mapping
types are guaranteed to maintain transaction number, size and order.
We use the Uncached variety of Normal mappings for the same reason
that we can't use C=1 mappings on ARMv5.
The xsc3 Architecture Specification documents TEXCB=00100 as being
Uncacheable and allowing coalescing of writes, which is also just
what we need.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CONFIG_AC97_BUS is used from both sound and ucb1400 drivers.
The recent change in Kconfig introduced the exclusive dependency on
CONFIG_SOUND, and disabled the ucb1400 build without sound.
This patch makes CONFIG_AC97_BUS independent.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
After fixing the u32 thinko I sill had occasional hickups on ATI chipsets
with small deltas. There seems to be a delay between writing the compare
register and the transffer to the internal register which triggers the
interrupt. Reading back the value makes sure, that it hit the internal
match register befor we compare against the counter value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use the HPET only in 32bit mode because:
1) some HPETs are 32bit only
2) on i386 there is no way to read/write the HPET atomic 64bit wide
The HPET code unification done by the "moron of the year" did
not take into account that unsigned long is different on 32 and
64 bit.
This thinko results in a possible endless loop in the clockevents
code, when the return comparison fails due to the 64bit/332bit
unawareness.
unsigned long cnt = (u32) hpet_read() + delta can wrap over 32bit.
but the final compare will fail and return -ETIME causing endless
loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Until the C1E patches arrived there where no users of periodic broadcast
before switching to oneshot mode. Now we need to trigger a possible
waiter for a periodic broadcast when switching to oneshot mode.
Otherwise we can starve them for ever.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use X86_FEATURE_NOPL to determine if it is safe to use P6 NOPs in
alternatives. Also, replace table and loop with simple if statement.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The long noops ("NOPL") are supposed to be detected by family >= 6.
Unfortunately, several non-Intel x86 implementations, both hardware
and software, don't obey this dictum. Instead, probe for NOPL
directly by executing a NOPL instruction and see if we get #UD.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The CPU feature detection code in the boot code is somewhat minimal,
and doesn't include all possible CPUID words. In particular, it
doesn't contain the code for CPU feature words 2 (Transmeta),
3 (Linux-specific), 5 (VIA), or 7 (scattered). Zero them out, so we
can still set those bits as known at compile time; in particular, this
allows creating a Linux-specific NOPL flag and have it required (and
therefore resolvable at compile time) in 64-bit mode.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
mmc_block_open() increments md->usage although it returns with -EROFS when
default mounting a MMC/SD card with write protect switch on. This
reference counting bug prevents /dev/mmcblkX from being released on card
removal, and situation worsen with reinsertion until the minor number
range runs out.
Reported-by: <sasin@solomon-systech.com>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix some pasto's in comments in the new linux/tracehook.h and
asm-generic/syscall.h files.
Reported-by: Wenji Huang <wenji.huang@oracle.com>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix regression tracked as http://bugzilla.kernel.org/show_bug.cgi?id=11361
and caused by commit f735a2a1a4 ("[netdrvr]
forcedeth: setup wake-on-lan before shutting down") that makes network
adapters integrated into the NVidia MCP55 chipsets fail to work in kexeced
kernels. The problem appears to be that if the adapter is put into D3_hot
during ->shutdown(), it cannot be brought back into D0 after kexec (ref.
http://marc.info/?l=linux-kernel&m=121900062814967&w=4). Therefore, only
put forcedeth into D3 during ->shutdown() if the system is to be powered
off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found we can no longer set limit to 0 with 2.6.27-rcX:
# mount -t cgroup -omemory xxx /mnt
# mkdir /mnt/0
# echo 0 > /mnt/0/memory.limit_in_bytes
bash: echo: write error: Device or resource busy
It turned out 'limit' can't be set to 'usage', which is wrong IMO.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix process time monotonicity
sched_clock: fix NOHZ interaction
* git://git.infradead.org/~dwmw2/dwmw2-2.6.27:
Revert "[ARM] use the new byteorder headers"
Fix conditional export of kvh.h and a.out.h to userspace.
[MTD] [NAND] tmio_nand: fix base address programming
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (98 commits)
V4L/DVB (8881): gspca: After 'while (retry--) {...}', retry will be -1 but not 0.
V4L/DVB (8880): PATCH: Fix parents on some webcam drivers
V4L/DVB (8877): b2c2 and bt8xx: udelay to mdelay
V4L/DVB (8876): budget: udelay changed to mdelay
V4L/DVB (8874): gspca: Adjust hstart for sn9c103/ov7630 and update usb-id's.
V4L/DVB (8873): gspca: Bad image offset with rev012a of spca561 and adjust exposure.
V4L/DVB (8872): gspca: Bad image format and offset with rev072a of spca561.
V4L/DVB (8870): gspca: Fix dark room problem with sonixb.
V4L/DVB (8869): gspca: Move the Sonix webcams with TAS5110C1B from sn9c102 to gspca.
V4L/DVB (8868): gspca: Support for vga modes with sif sensors in sonixb.
V4L/DVB (8844): dabusb_fpga_download(): fix a memory leak
V4L/DVB (8843): tda10048_firmware_upload(): fix a memory leak
V4L/DVB (8842): vivi_release(): fix use-after-free
V4L/DVB (8840): dib0700: add basic support for Hauppauge Nova-TD-500 (84xxx)
V4L/DVB (8839): dib0700: add comment to identify 35th USB id pair
V4L/DVB (8837): dvb: fix I2C adapters name size
V4L/DVB (8835): gspca: Same pixfmt as the sn9c102 driver and raw Bayer added in sonixb.
V4L/DVB (8834): gspca: Have a bigger buffer for sn9c10x compressed images.
V4L/DVB (8833): gspca: Cleanup the sonixb code.
V4L/DVB (8832): gspca: Bad pixelformat of vc0321 webcams.
...
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
acer-wmi: remove debugfs entries upon unloading
ACPI: Avoid bogus timeout about SMbus check
fujitsu-laptop: fix regression for P8010 in 2.6.27-rc
ACPI: Make Len Brown the ACPI maintainer again
ACPI: thinkpad-acpi: wan radio control is not experimental
PNPACPI: ignore the producer/consumer bit for extended IRQ descriptors
acpi: add checking for NULL early param
ACPI: Fix typo in "Disable MWAIT via DMI on broken Compal board"
ACPI: Fix now signed module parameter.
ACPI: Change package length error to warning
ACPI: Fix now signed module parameter.
Currently init_initrd() probes initrd header at the last page of kernel
image, but it is valid only if addinitrd was used. If addinitrd was not
used, the area contains garbage so probing there might misdetect initrd
header (magic number is not strictly robust).
This patch introduces CONFIG_PROBE_INITRD_HEADER to explicitly enable this
probing.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The txx9_pcode variable was introduced in commit
fe1c2bc64f65003b39f331a8e4b0d15b235a4afd ("TXx9: Add 64-bit support")
but was not initialized properly.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trap_init issues flush_icache_range(), which uses ipi functions to
get icache flushing done on all cpus. But this is done before interrupts
are enabled and caused WARN_ON messages. This changeset introduces
a new local_flush_icache_range() and uses it before interrupts (and
additional CPUs) are enabled to avoid this problem.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With -ffunction-section the entries in __dbe_table aren't no longer
sorted, so the lookup of exception addresses in do_be() failed for
some addresses. To avoid this we now sort __dbe_table.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 087d833e5a, which was
reported to break wireless at least in some combinations with 32bit user
space and a 64bit kernel. Alex Williamnson bisected it to this commit.
Reported-and-bisected-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UBIFS does not really work correctly when fanout is 2,
because of the way we manage the indexing tree. It may
just become a list and UBIFS screws up.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Spencer reported a problem where utime and stime were going negative despite
the fixes in commit b27f03d4bd. The suspected
reason for the problem is that signal_struct maintains it's own utime and
stime (of exited tasks), these are not updated using the new task_utime()
routine, hence sig->utime can go backwards and cause the same problem
to occur (sig->utime, adds tsk->utime and not task_utime()). This patch
fixes the problem
TODO: using max(task->prev_utime, derived utime) works for now, but a more
generic solution is to implement cputime_max() and use the cputime_gt()
function for comparison.
Reported-by: spencer@bluehost.com
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If HLT stops the TSC, we'll fail to account idle time, thereby inflating the
actual process times. Fix this by re-calibrating the clock against GTOD when
leaving nohz mode.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit ae82cbfc8b. It
needs the new byteorder headers to be exported to userspace, and
they aren't yet -- and probably shouldn't be, at this point in the
2.6.27 release cycle (or ever, for that matter).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Should clear the next pointer of the TX if we are sure that the
next TX (say NXT) will be submitted to the channel too. Overwise,
we break the chain of descriptors, because we lose the information
about the next descriptor to run. So next time, when invoke
async_tx_run_dependencies() with TX, it's TX->next will be NULL, and
NXT will be never submitted.
Cc: <stable@kernel.org> [2.6.26]
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some architectures have moved the asm/ into arch/ and some have not.
This patch checks for a.out.h and kvh.h in both places before exporting
the corresponding file from linux/
[dwmw2: simplified a little]
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix offset of second word used for programming base address of memory
window. Also program tmio with offset of the FCR, not with physical
memory location.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The minimum reprogramming delta was hardcoded in HPET ticks,
which is stupid as it does not work with faster running HPETs.
The C1E idle patches made this prominent on AMD/RS690 chipsets,
where the HPET runs with 25MHz. Set it to 5us which seems to be
a reasonable value and fixes the problems on the bug reporters
machines. We have a further sanity check now in the clock events,
which increases the delta when it is not sufficient.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Tested-by: Dmitry Nezhevenko <dion@inhex.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The C1E/HPET bug reports on AMDX2/RS690 systems where tracked down to a
too small value of the HPET minumum delta for programming an event.
The clockevents code needs to enforce an interrupt event on the clock event
device in some cases. The enforcement code was stupid and naive, as it just
added the minimum delta to the current time and tried to reprogram the device.
When the minimum delta is too small, then this loops forever.
Add a sanity check. Allow reprogramming to fail 3 times, then print a warning
and double the minimum delta value to make sure, that this does not happen again.
Use the same function for both tick-oneshot and tick-broadcast code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While chasing the C1E/HPET bugreports I went through the clock events
code inch by inch and found that the broadcast device can be initialized
and shutdown multiple times. Multiple shutdowns are not critical, but
useless waste of time. Multiple initializations are simply broken. Another
CPU might have the device in use already after the first initialization and
the second init could just render it unusable again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In tick_oneshot_setup we program the device to the given next_event,
but we do not check the return value. We need to make sure that the
device is programmed enforced so the interrupt handler engine starts
working. Split out the reprogramming function from tick_program_event()
and call it with the device, which was handed in to tick_setup_oneshot().
Set the force argument, so the devices is firing an interrupt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The reprogramming of the periodic broadcast handler was broken,
when the first programming returned -ETIME. The clockevents code
stores the new expiry value in the clock events device next_event field
only when the programming time has not been elapsed yet. The loop in
question calculates the new expiry value from the next_event value
and therefor never increases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is a ordering related problem with clockevents code, due to which
clockevents_register_device() called after tickless/highres switch
will not work. The new clockevent ends up with clockevents_handle_noop as
event handler, resulting in no timer activity.
The problematic path seems to be
* old device already has hrtimer_interrupt as the event_handler
* new clockevent device registers with a higher rating
* tick_check_new_device() is called
* clockevents_exchange_device() gets called
* old->event_handler is set to clockevents_handle_noop
* tick_setup_device() is called for the new device
* which sets new->event_handler using the old->event_handler which is noop.
Change the ordering so that new device inherits the proper handler.
This does not have any issue in normal case as most likely all the clockevent
devices are setup before the highres switch. But, can potentially be affecting
some corner case where HPET force detect happens after the highres switch.
This was a problem with HPET in MSI mode code that we have been experimenting
with.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch teaches the i2c-sh_mobile driver to make use of wait irqs.
Without this patch only dte irqs are used which may lead to overruns
and cases of missing stop and extra bytes being read on the i2c bus.
Use of wait irqs forces the hardware to pause and wait until the cpu
is ready. Polling is also reworked in this patch to fix ms delay issues.
Verified with bus analyzer and tested on MigoR and AP325RXA boards.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a problem within the SH implementation of resume_kernel code,
that implements in assembly the bulk of preempt_schedule_irq function without
taking care of the extra code needed to handle the BKL preemptible.
The patch basically consists of removing this asm code and calling the common
C implementation (see kernel/sched.c) as other archs do.
Another change is the missing 'cli' macro invocation at the beginning of
the resume_kernel.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Apparently, there are more different versions of Lenovo 3000 N100, some
of them working properly with active mux, and some of them requiring it
being switched off.
This patch applies 'nomux' only to the specific product name that is
reported to behave badly unless 'nomux' is specified.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Yinghai Lu
Krzysztof Helt
Dominik Brodowski
Maciej W. Rozycki
Lennert Buytenhek
Takashi Iwai
Thomas Gleixner
H. Peter Anvin
Andrew Morton
Roland McGrath
Stanislaw Gruszka
Rafael J. Wysocki
Li Zefan
Linus Torvalds
Atsushi Nemoto
Thomas Bogendoerfer
Artem Bityutskiy
Balbir Singh
Peter Zijlstra
David Woodhouse
Yuri Tikhonov
Khem Raj
Dmitry Baryshkov
Venkatesh Pallipadi
Magnus Damm
Paul Mundt
Carmelo Amoroso
Jiri Kosina