The Renesas Compare Match Timer 0 and 1 (CMT0/1) variants have a
register to control the clock supply to the individual channels.
Currently the driver does not touch this register, and relies on the
documented initial value, which has the clock supply enabled for all
channels present.
However, when Linux starts on the APE6-EVM development board, only the
clock supply to the first CMT1 channel is enabled. Hence the first
channel (used as a clockevent) works, while the second channel (used as
a clocksource) does not. Note that the default system clocksource is
the Cortex-A15 architectured timer, and the user needs to manually
switch to the CMT1 clocksource to trigger the broken behavior.
Fix this by removing the fragile dependency on implicit reset and/or
boot loader state, and by enabling the clock supply explicitly for all
channels used instead. This requires postponing the clk_disable() call,
else the timer's registers cannot be accessed in sh_cmt_setup_channel().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210194648.2901899-1-geert+renesas@glider.be
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
To better describe what the pm_genpd_syscore_poweroff|poweron() functions
actually do, let's rename them to dev_pm_genpd_suspend|resume() and update
the rather few callers of them accordingly (a couple of clocksource
drivers).
Moreover, let's take the opportunity to add some documentation of these
exported functions, as that is currently missing.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Old early platform device support is now sh-specific. Before moving on
to implementing new early platform framework based on real platform
devices, prefix all early platform symbols with 'sh_'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperH is the only user of the current implementation of early platform
device support. We want to introduce a more robust approach to early
probing. As the first step - move all the current early platform code
to arch/sh.
In order not to export internal drivers/base functions to arch code for
this temporary solution - copy the two needed routines for driver
matching from drivers/base/platform.c to arch/sh/drivers/platform_early.c.
Also: call early_platform_cleanup() from subsys_initcall() so that it's
called after all early devices are probed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the CMT driver to mark "renesas,cmt-48" as deprecated.
Instead of documenting a theoretical hardware device based on current software
support level, define DT bindings top-down based on available data sheet
information and make use of part numbers in the DT compat string.
In case of the only in-tree users r8a7740 and sh73a0 the compat strings
"renesas,r8a7740-cmt1" and "renesas,sh73a0-cmt1" may be used instead.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add SoC-specific matching for CMT1 on r8a7740 and sh73a0.
This allows us to move away from the old DT bindings such as
- "renesas,cmt-48-sh73a0"
- "renesas,cmt-48-r8a7740"
- "renesas,cmt-48"
in favour for the now commonly used format "renesas,<soc>-<device>"
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add support for the R-Car gen3 CMT types 0/1 -- they seem to be the same
CMT types 0/1 as in R-Car gen2 SoCs.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
There's no good reason for the sh_cmt_of_table[] initializer to
violate the 80-column limit, especially after the commit 8d50e9476b
("clocksource/drivers/sh_cmt: Mark "renesas,cmt-48-gen2" deprecated")
partially fixed it -- fix the R-Car gen2 related entries as well.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The driver seems to abuse *unsigned long* not only for the (32-bit)
register values but also for the 'sh_cmt_channel::total_cycles' which
needs to always be 64-bit -- as a result, the clocksource's mask is
needlessly clamped down to 32-bits on the 32-bit machines...
Fixes: 19bdc9d061 ("clocksource: sh_cmt clocksource support")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When trying to use CMT for clockevents on R-Car gen3 SoCs, I noticed
that 'max_delta_ns' for the broadcast timer (CMT) was shown as 1000 in
/proc/timer_list. It turned out that when calculating it, the driver did
1 << 32 (causing what I think was undefined behavior) resulting in a zero
delta, later clamped to 1000 by cev_delta2ns(). The root cause turned out
to be that the driver abused *unsigned long* for the CMT register values
(which are 16/32-bit), so that the calculation of 'ch->max_match_value'
in sh_cmt_setup_channel() used the wrong branch. Using more proper 'u32'
instead fixed 'max_delta_ns' and even fixed the switching an active
clocksource to CMT (which caused the system to turn non-interactive
before).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch updates license to use SPDX-License-Identifier instead of verbose
license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use the existing of_device_get_match_data() helper instead of
open-coding its functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The in-driver channel configuration in sh_cmt_info.channels_mask is now
always set for all CMT devices instantiated from DT.
Hence the "renesas,channels-mask" property is no longer checked, and its
handling can be removed, cfr. commit 4e18111ff3 ("devicetree:
bindings: Remove deprecated properties").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Document in the driver that "renesas,cmt-48-gen2" is deprecated, but
still supported for backward compatibility with old DTBs, cfr. commit
4e18111ff3 ("devicetree: bindings: Remove deprecated
properties").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove driver matching support for the unused "renesas,cmt-32" and
"renesas,cmt-32-fast" compatible values, cfr. commit 203bb34799
("devicetree: bindings: Remove unused 32-bit CMT bindings").
As this removes the last user of SH_CMT_32BIT_FAST, all support for this
variant is removed from the driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add support for the new R-Car Gen2 CMT0 and CMT1 bindings. Support
for the old DT binding is still kept around, however devices using
such binding will be treated as a low-feature CMT0 device. If users
want to make use of CMT1-specific features then they need to update
their DTBs. No special CMT1-specific features are however implemented
by his patch, only DT bindings are redone as groundwork for future
feature patches.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Always use 0x3f as channel mask for the SH_CMT_48BIT type of devices.
Once this patch is applied the "renesas,channels-mask" property will
be ignored by the driver for older devices matching SH_CMT_48BIT. In
the future when all CMT types store channel mask in the driver then
we will be able to deprecate and remove "renesas,channels-mask" from DTS.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the sh_cmt clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
With the upcoming NTP correction related rate adjustments to be implemented
in the clockevents core, the latter needs to get informed about every rate
change of a clockevent device made after its registration.
Currently, sh_cmt violates this requirement in that it registers its
clockevent device with a dummy rate and sets its final ->mult and ->shift
values from its ->set_state_oneshot() and ->set_state_periodic() functions
respectively.
This patch moves the setting of the clockevent device's ->mult and ->shift
values to before its registration.
Note that there has been some back and forth regarding this question with
respect to the clocksource also provided by this driver:
commit f4d7c3565c ("clocksource: sh_cmt: compute mult and shift before
registration")
moves the rate determination from the clocksource's ->enable() function to
before its registration. OTOH, the later
commit 3593f5fe40 ("clocksource: sh_cmt: __clocksource_updatefreq_hz()
update")
basically reverts this, saying
"Without this patch the old code uses clocksource_register() together
with a hack that assumes a never changing clock rate."
However, I checked all current sh_cmt users in arch/sh as well as in
arch/arm/mach-shmobile carefully and right now, none of them changes any
rate in any clock tree relevant to sh_cmt after their respective
time_init(). Since all sh_cmt instances are created after time_init(), none
of them should ever observe any clock rate changes.
What's more, both, a clocksource as well as a clockevent device, can
immediately get selected for use at their registration and thus, enabled
at this point already. So it's probably safer to assume a "never changing
clock rate" here.
- Move the struct sh_cmt_channel's ->rate member to struct sh_cmt_device:
it's a property of the underlying clock which is in turn specific to
the sh_cmt_device.
- Determine the ->rate value in sh_cmt_setup() at device probing rather
than at first usage.
- Set the clockevent device's ->mult and ->shift values right before its
registration.
- Although not strictly necessary for the upcoming clockevent core changes,
set the clocksource's rate at its registration for consistency.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Memory for cmt struct is allocated by kzalloc() in sh_cmt_setup.
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Pull timer updates from Thomas Gleixner:
"Rather large, but nothing exiting:
- new range check for settimeofday() to prevent that boot time
becomes negative.
- fix for file time rounding
- a few simplifications of the hrtimer code
- fix for the proc/timerlist code so the output of clock realtime
timers is accurate
- more y2038 work
- tree wide conversion of clockevent drivers to the new callbacks"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (88 commits)
hrtimer: Handle failure of tick_init_highres() gracefully
hrtimer: Unconfuse switch_hrtimer_base() a bit
hrtimer: Simplify get_target_base() by returning current base
hrtimer: Drop return code of hrtimer_switch_to_hres()
time: Introduce timespec64_to_jiffies()/jiffies_to_timespec64()
time: Introduce current_kernel_time64()
time: Introduce struct itimerspec64
time: Add the common weak version of update_persistent_clock()
time: Always make sure wall_to_monotonic isn't positive
time: Fix nanosecond file time rounding in timespec_trunc()
timer_list: Add the base offset so remaining nsecs are accurate for non monotonic timers
cris/time: Migrate to new 'set-state' interface
kernel: broadcast-hrtimer: Migrate to new 'set-state' interface
xtensa/time: Migrate to new 'set-state' interface
unicore/time: Migrate to new 'set-state' interface
um/time: Migrate to new 'set-state' interface
sparc/time: Migrate to new 'set-state' interface
sh/localtimer: Migrate to new 'set-state' interface
score/time: Migrate to new 'set-state' interface
s390/time: Migrate to new 'set-state' interface
...
Since the removal of the r8a7740 legacy SoC code in commit
44d88c754e ("ARM: shmobile: Remove legacy SoC code for R-Mobile
A1"), all former users of the "sh-cmt-48-gen2" platform device name are
only supported in generic DT-only ARM multi-platform builds. The driver
doesn't need to match platform devices by name anymore, hence remove the
corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Migrate sh_cmt driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Cc: Magnus Damm <damm+renesas@opensource.se>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Since commit 914d7d1484 ("ARM: shmobile: r8a73a4: Remove legacy
code"), all former users of the "sh-cmt-48-gen2" platform device name
are only supported in generic DT-only ARM multi-platform builds. The
driver doesn't need to match platform devices by name anymore, hence
remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Since commit 59b89af1d5 ("ARM: shmobile: sh7372: Remove Legacy C
SoC code"), there are no more users left of the "sh-cmt-32-fast"
platform device name. Hence remove the corresponding platform_device_id
entry from the driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Currently the sh_cmt clocksource timer is disabled or enabled
unconditionally on clocksource suspend resp. resume, even if a
better clocksource is present (e.g. arch_sys_counter) and the
sh_cmt clocksource is not enabled.
As sh_cmt is a syscore device when its timer is enabled, this
may lead to a genpd.prepared_count imbalance in the presence of
PM Domains, which may cause a lock-up during reboot after s2ram.
During suspend:
- pm_genpd_prepare() is called for all non-syscore devices (incl.
sh_cmt), increasing genpd.prepared_count for each device,
- clocksource.suspend() is called for all clocksource devices,
- sh_cmt_clocksource_suspend() calls sh_cmt_stop(), which is a no-op
as the clocksource was not enabled.
During resume:
- clocksource.resume() is called for all clocksource devices,
- sh_cmt_clocksource_resume() calls sh_cmt_start(), which enables the
clocksource timer, and turns sh_cmt into a syscore device,
- pm_genpd_complete() is called for all non-syscore devices (excl.
sh_cmt now!), decreasing genpd.prepared_count for each device but
sh_cmt.
Now genpd.prepared_count of the PM Domain containing sh_cmt is
still 1 instead of zero. On subsequent suspend/resume cycles,
sh_cmt is still a syscore device, hence it's skipped for
pm_genpd_{prepare,complete}(), keeping the imbalance of
genpd.prepared_count at 1.
During reboot:
- platform_drv_shutdown() is called for any platform device that has
a driver with a .shutdown() method (only rcar-dmac on R-Car Gen2),
- platform_drv_shutdown() calls dev_pm_domain_detach(), which
calls genpd_dev_pm_detach(),
- genpd_dev_pm_detach() keeps calling pm_genpd_remove_device() until
it doesn't return -EAGAIN[*],
- If the device is part of the same PM Domain as sh_cmt,
pm_genpd_remove_device() always fails with -EAGAIN due to
genpd.prepared_count > 0.
- Infinite loop in genpd_dev_pm_detach()[*].
[*] Commit 93af5e9354 ("PM / Domains: Avoid infinite loops in
attach/detach code") already limited the number of loop iterations,
avoiding the lock-up.
To fix this, only disable or enable the clocksource timer on
clocksource suspend resp. resume if the clocksource was enabled.
This was tested on r8a7791/koelsch with the CPG Clock Domain:
- using arch_sys_counter as the clocksource, which is the default, and
which showed the problem,
- using sh_cmt as a clocksource ("echo ffca0000.timer > \
/sys/devices/system/clocksource/clocksource0/current_clocksource"),
which behaves the same as before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438875126-12596-2-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo requested this function be renamed to improve readability,
so I've renamed __clocksource_updatefreq_scale() as well as the
__clocksource_updatefreq_hz/khz() functions to avoid
squishedtogethernames.
This touches some of the sh clocksources, which I've not tested.
The arch/arm/plat-omap change is just a comment change for
consistency.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1426133800-29329-13-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Document DT bindings and parse them in the CMT driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
The global spinlock is used to protect the shared start/stop register.
Now that all CMT channels are handled by a single device instance, use a
per-device spinlock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Now that all platforms have switched to the new-style platform data,
drop support for the legacy version.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
[dlezcano] : refreshed against latest modifications: kmalloc -> kzalloc
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Clock sources don't need an IRQ, request the IRQ only for channels used
as clock event devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already
includes a copy of the GPL.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The sh_cmt driver gets the CMT functional clock using a connection ID of
"cmt_fck". While all SH SoCs create clock lookup entries with a NULL
device ID and a "cmt_fck" connection ID, the ARM SoCs use the device ID
only with a NULL connection ID. This works on legacy platforms but will
break on ARM with DT boot.
Fix the situation by using a connection ID of "fck" in the non-legacy
platform data case. Clock lookup entries will be renamed to use the
device ID as well as the connection ID as platforms get moved to new
platform data. The legacy code will eventually be dropped, leaving us
with device ID based clock lookup, compatible with DT boot.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
CMT hardware devices can support multiple channels, with global
registers and per-channel registers. The sh_cmt driver currently models
the hardware with one Linux device per channel. This model makes it
difficult to handle global registers in a clean way.
Add support for a new model that uses one Linux device per timer with
multiple channels per device. This requires changes to platform data,
add new channel configuration fields.
Support for the legacy model is kept and will be removed after all
platforms switch to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
All boards use or should use a clock source rating of 125 for the CMT,
hardcode it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
All boards use or should use a clock event rating of 125 for the CMT,
hardcode it in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The CMT is a global timer not restricted to a single CPU. It has a lower
rating than the TMU or ARM architected timer, but is still useful on
systems where the other timers are stopped during CPU sleep.
When multiple timers are available the timers core selects which timer
to use based on timer ratings.
On SMP systems where timer broadcasting is required, one dummy timer is
instantiated per CPU with a rating of 100. On those systems the CMT
timer has a rating of 80, which makes the dummy timer selected by
default on all CPUs. The CMT is then available, and will be used as a
broadcast timer.
On UP systems no dummy timer is instantiated. The CMT timer has a rating
of 125 on those systems and is used directly as a clock event device for
CPU0 without broadcasting.
The CMT rating shouldn't depend on whether we boot a UP or SMP system.
We can't raise the CMT rating to 125 on SMP systems. This would select
CMT as the clock event device for CPU0 as its rating is higher than the
dummy timer rating, and would leave the system without a broadcast
timer. We could instead lower the rating to 80 on all systems, but that
wouldn't reflect reality as ratings between 1 and 99 are documented as
"unfit for real use".
We should raise the rating above 99 and still have the CMT selected as a
broadcast timer. This can be done by changing the cpumask from
cpumask_of(0) to cpu_possible_mask. In that case the timer selection
logic will prefer the previously probed and already selected dummy timer
for all CPUs based on the fact that already selected per-cpu timers are
preferred over new global timers, regardless of their respective
ratings. This also better reflects reality, as the CMT is not tied to
the boot CPU.
Ideally the timer selection logic should realize that the CMT needs to
be used as a broadcast timer on SMP systems as no other broadcast timer
is available, regardless of the cpumask and rating.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Create a new sh_cmt_info structure to hold static information about the
device model and reference that structure from the sh_cmt_device
structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Geert Uytterhoeven
Linus Torvalds
Niklas Söderlund
Ulf Hansson
Christoph Hellwig
Bartosz Golaszewski
Magnus Damm
Stephen Boyd
Sergei Shtylyov
Kuninori Morimoto
Kees Cook
Nicolai Stange
Thomas Gleixner
Alexey Klimov
Viresh Kumar
John Stultz
Laurent Pinchart
Jingoo Han