Add a preempt count base offset to compare against the current
preempt level count. It prepares to pull up the might_sleep
check from cond_resched() to cond_resched_lock() and
cond_resched_bh().
For these two helpers, we need to respectively ensure that once
we'll unlock the given spinlock / reenable local softirqs, we
will reach a sleepable state.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
[ Move and rename preempt_count_equals() ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1247725694-6082-4-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cover the off case for __might_sleep(), so that we avoid
#ifdefs in files that make use of it. Especially, this prepares
for the __might_sleep() pull up on cond_resched().
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1247725694-6082-3-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch introduces a new sysctl:
/proc/sys/kernel/panic_on_io_nmi
which defaults to 0 (off).
When enabled, the kernel panics when the kernel receives an NMI
caused by an IO error.
The IO error triggered NMI indicates a serious system
condition, which could result in IO data corruption. Rather
than contiuing, panicing and dumping might be a better choice,
so one can figure out what's causing the IO error.
This could be especially important to companies running IO
intensive applications where corruption must be avoided, e.g. a
bank's databases.
[ SuSE has been shipping it for a while, it was done at the
request of a large database vendor, for their users. ]
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: Roberto Angelino <robertangelino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <20090624213211.GA11291@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Follow-up to "block: enable by default support for large devices
and files on 32-bit archs".
Rename CONFIG_LBD to CONFIG_LBDAF to:
- allow update of existing [def]configs for "default y" change
- reflect that it is used also for large files support nowadays
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (64 commits)
debugfs: use specified mode to possibly mark files read/write only
debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
xen: remove driver_data direct access of struct device from more drivers
usb: gadget: at91_udc: remove driver_data direct access of struct device
uml: remove driver_data direct access of struct device
block/ps3: remove driver_data direct access of struct device
s390: remove driver_data direct access of struct device
parport: remove driver_data direct access of struct device
parisc: remove driver_data direct access of struct device
of_serial: remove driver_data direct access of struct device
mips: remove driver_data direct access of struct device
ipmi: remove driver_data direct access of struct device
infiniband: ehca: remove driver_data direct access of struct device
ibmvscsi: gadget: at91_udc: remove driver_data direct access of struct device
hvcs: remove driver_data direct access of struct device
xen block: remove driver_data direct access of struct device
thermal: remove driver_data direct access of struct device
scsi: remove driver_data direct access of struct device
pcmcia: remove driver_data direct access of struct device
PCIE: remove driver_data direct access of struct device
...
Manually fix up trivial conflicts due to different direct driver_data
direct access fixups in drivers/block/{ps3disk.c,ps3vram.c}
This adds a KERN_DEFAULT loglevel marker, for when you cannot decide
which loglevel you want, and just want to keep an existing printk
with the default loglevel.
The difference between having KERN_DEFAULT and having no log-level
marker at all is two-fold:
- having the log-level marker will now force a new-line if the
previous printout had not added one (perhaps because it forgot,
but perhaps because it expected a continuation)
- having a log-level marker is required if you are printing out a
message that otherwise itself could perhaps otherwise be mistaken
for a log-level.
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
It used to be that we would only look at the log-level in a printk()
after explicit newlines, which can cause annoying problems when the
previous printk() did not end with a '\n'. In that case, the log-level
marker would be just printed out in the middle of the line, and be
seen as just noise rather than change the logging level.
This changes things to always look at the log-level in the first
bytes of the printout. If a log level marker is found, it is always
used as the log-level. Additionally, if no newline existed, one is
added (unless the log-level is the explicit KERN_CONT marker, to
explicitly show that it's a continuation of a previous line).
Acked-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pr_debug() used to produce zero code unless DEBUG was #defined. This is
now no longer the case in practice[1].
There are places where it's useful to have debugging printks, but we don't
want them to generate any code in production kernels.
So add a new macro, pr_devel(), for _devel_opment, to provide the old
semantics, ie. if the programmer doesn't explicitly enable debugging, no
code is produced.
[1]: You can turn CONFIG_DYNAMIC_DEBUG off, but it's enabled in at least
one distro kernel, so it's not really a solution.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Greg Banks <gnb@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* 'printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
printk: correct the behavior of printk_timed_ratelimit()
vsprintf: unify the format decoding layer for its 3 users, cleanup
fix regression from "vsprintf: unify the format decoding layer for its 3 users"
vsprintf: fix bug in negative value printing
vsprintf: unify the format decoding layer for its 3 users
vsprintf: add binary printf
printk: introduce printk_once()
Fix trivial conflicts (printk_once vs log_buf_kexec_setup() added near
each other) in include/linux/kernel.h.
It would be nice to be able to extract the dmesg log from a vmcore file
without needing to keep the debug symbols for the running kernel handy all
the time. We have a facility to do this in /proc/vmcore. This patch adds
the log_buf and log_end symbols to the vmcoreinfo area so that tools (like
makedumpfile) can easily extract the dmesg logs from a vmcore image.
[akpm@linux-foundation.org: several fixes and cleanups]
[akpm@linux-foundation.org: fix unused log_buf_kexec_setup()]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Simon Horman <horms@verge.net.au>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We cover all log-levels by pr_... macros except KERN_CONT one. Add it
for convenience.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_DYNAMIC_DEBUG is enabled, allow callers of pr_debug()
to provide their own definition of pr_fmt() even if that definition
uses tricks like
#define pr_fmt(fmt) "%s:" fmt, __func__
Signed-off-by: Greg Banks <gnb@sgi.com>
Cc: Jason Baron <jbaron@redhat.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch combines Greg Bank's dprintk() work with the existing dynamic
printk patchset, we are now calling it 'dynamic debug'.
The new feature of this patchset is a richer /debugfs control file interface,
(an example output from my system is at the bottom), which allows fined grained
control over the the debug output. The output can be controlled by function,
file, module, format string, and line number.
for example, enabled all debug messages in module 'nf_conntrack':
echo -n 'module nf_conntrack +p' > /mnt/debugfs/dynamic_debug/control
to disable them:
echo -n 'module nf_conntrack -p' > /mnt/debugfs/dynamic_debug/control
A further explanation can be found in the documentation patch.
Signed-off-by: Greg Banks <gnb@sgi.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Impact: fix callsites with dynamic format strings
Since its new binary implementation, trace_printk() internally uses static
containers for the format strings on each callsites. But the value is
assigned once at build time, which means that it can't take dynamic
formats.
So this patch unearthes the raw trace_printk implementation for the callers
that will need trace_printk to be able to carry these dynamic format
strings. The trace_printk() macro will use the appropriate implementation
for each callsite. Most of the time however, the binary implementation will
still be used.
The other impact of this patch is that mmiotrace_printk() will use the old
implementation because it calls the low level trace_vprintk and we can't
guess here whether the format passed in it is dynamic or not.
Some parts of this patch have been written by Steven Rostedt (most notably
the part that chooses the appropriate implementation for each callsites).
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: micro-optimization
trace_printk() does this unconditionally:
trace_printk_fmt = fmt;
Where trace_printk_fmt is an entry into a global array. This is
very SMP-unfriendly.
So only write it once per bootup.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1236356510-8381-5-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: faster and lighter tracing
Now that we have trace_bprintk() which is faster and consume lesser
memory than trace_printk() and has the same purpose, we can now drop
the old implementation in favour of the binary one from trace_bprintk(),
which means we move all the implementation of trace_bprintk() to
trace_printk(), so the Api doesn't change except that we must now use
trace_seq_bprintk() to print the TRACE_PRINT entries.
Some changes result of this:
- Previously, trace_bprintk depended of a single tracer and couldn't
work without. This tracer has been dropped and the whole implementation
of trace_printk() (like the module formats management) is now integrated
in the tracing core (comes with CONFIG_TRACING), though we keep the file
trace_printk (previously trace_bprintk.c) where we can find the module
management. Thus we don't overflow trace.c
- changes some parts to use trace_seq_bprintk() to print TRACE_PRINT entries.
- change a bit trace_printk/trace_vprintk macros to support non-builtin formats
constants, and fix 'const' qualifiers warnings. But this is all transparent for
developers.
- etc...
V2:
- Rebase against last changes
- Fix mispell on the changelog
V3:
- Rebase against last changes (moving trace_printk() to kernel.h)
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1236356510-8381-5-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
The functions tracing_start/tracing_stop have been moved to kernel.h.
These are not the functions a developer most likely wants to use
when they want to insert a place to stop tracing and restart it from
user space.
tracing_start/tracing_stop was created to work with things like
suspend to ram, where even calling smp_processor_id() can crash the
system. The tracing_start/tracing_stop was used to stop the tracer from
doing anything. These are still light weight functions, but add a bit
more overhead to be able to stop the tracers. They also have no interface
back to userland. That is, if the kernel calls tracing_stop, userland
can not start tracing.
What a developer most likely wants to use is tracing_on/tracing_off.
These are very light weight functions (simply sets or clears a bit).
These functions just stop recording into the ring buffer. The tracers
don't even know that this happens except that they would receive NULL
from the ring_buffer_lock_reserve function.
Also, there's a way for the user land to enable or disable this bit.
In debugfs/tracing/tracing_on, a user may echo "0" (same as tracing_off())
or echo "1" (same as tracing_on()) into this file. This becomes handy when
a kernel developer is debugging and wants tracing to turn off when it
hits an anomaly. Then the developer can examine the trace, and restart
tracing if they want to try again (echo 1 > tracing_on).
This patch moves the prototypes for tracing_on/tracing_off to kernel.h
and comments their use, so that a kernel developer will know how
to use them.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Make common utility functions such as trace_printk() and
tracing_start()/tracing_stop() generally available to kernel
code.
Cc: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The swap() macro is accidentally retuning the value of its first argument.
Change it into a doesn't-return-anything macro before someone goes and
relies upon this behaviour.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This pattern shows up frequently in the kernel:
static int once = 1;
...
if (once) {
once = 0;
printk(KERN_ERR "message\n");
}
...
So add a printk_once() helper macro that reduces this to a single line
of:
printk_once(KERN_ERR "message\n");
It works analogously to WARN_ONCE() & friends. (We use a macro not
an inline because vararg expansion in inlines looks awkward and the
macro is simple enough.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There have been some local definitions of swap(), it's time to replace
them all with a uniform one.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a helper macro to divide two numbers and round the result to the
nearest whole number. This is a helper macro for hwmon drivers that want
to convert incoming sysfs values per standard hwmon practice, though the
macro itself can be used by anyone.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Statically defined DEBUG should take precedence over
dynamically enabled debugging; otherwise adding DEBUG
(like, for example, via CONFIG_DEBUG_KOBJECT) does not
have the expected result of printing pr_debug() and dev_dbg()
messages unconditionally.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
stacktrace: provide save_stack_trace_tsk() weak alias
rcu: provide RCU options on non-preempt architectures too
printk: fix discarding message when recursion_bug
futex: clean up futex_(un)lock_pi fault handling
"Tree RCU": scalable classic RCU implementation
futex: rename field in futex_q to clarify single waiter semantics
x86/swiotlb: add default swiotlb_arch_range_needs_mapping
x86/swiotlb: add default phys<->bus conversion
x86: unify pci iommu setup and allow swiotlb to compile for 32 bit
x86: add swiotlb allocation functions
swiotlb: consolidate swiotlb info message printing
swiotlb: support bouncing of HighMem pages
swiotlb: factor out copy to/from device
swiotlb: add arch hook to force mapping
swiotlb: allow architectures to override phys<->bus<->phys conversions
swiotlb: add comment where we handle the overflow of a dma mask on 32 bit
rcu: fix rcutorture behavior during reboot
resources: skip sanity check of busy resources
swiotlb: move some definitions to header
swiotlb: allow architectures to override swiotlb pool allocation
...
Fix up trivial conflicts in
arch/x86/kernel/Makefile
arch/x86/mm/init_32.c
include/linux/hardirq.h
as per Ingo's suggestions.
A common reason for device drivers to implement their own printk macros
is the lack of a printk prefix with the standard pr_xyz macros.
Introduce a pr_fmt() macro that is applied for every pr_xyz macro to the
format string.
The most common use of the pr_fmt macro would be to add the name of the
device driver to all pr_xyz messages in a source file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put the kernel-doc for might_sleep() _immediately_ before the macro
(no intervening lines). Otherwise kernel-doc complains like so:
Warning(linux-2.6.27-rc3-git2//include/linux/kernel.h:129): No description found for parameter 'file'
Warning(linux-2.6.27-rc3-git2//include/linux/kernel.h:129): No description found for parameter 'line'
because kernel-doc is looking at the wrong function prototype (i.e.,
__might_sleep). [Yes, I have a todo note to myself to check/warn for that
inconsistency in scripts/kernel-doc.]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Open code NIP6_FMT in the one call inside sscanf and one user
of NIP6() that could use %p6 in the netfilter code.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
It's somewhat unlikely that it happens, but right now a race window
between interrupts or machine checks or oopses could corrupt the tainted
bitmap because it is modified in a non atomic fashion.
Convert the taint variable to an unsigned long and use only atomic bit
operations on it.
Unfortunately this means the intvec sysctl functions cannot be used on it
anymore.
It turned out the taint sysctl handler could actually be simplified a bit
(since it only increases capabilities) so this patch actually removes
code.
[akpm@linux-foundation.org: remove unneeded include]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Base infrastructure to enable per-module debug messages.
I've introduced CONFIG_DYNAMIC_PRINTK_DEBUG, which when enabled centralizes
control of debugging statements on a per-module basis in one /proc file,
currently, <debugfs>/dynamic_printk/modules. When, CONFIG_DYNAMIC_PRINTK_DEBUG,
is not set, debugging statements can still be enabled as before, often by
defining 'DEBUG' for the proper compilation unit. Thus, this patch set has no
affect when CONFIG_DYNAMIC_PRINTK_DEBUG is not set.
The infrastructure currently ties into all pr_debug() and dev_dbg() calls. That
is, if CONFIG_DYNAMIC_PRINTK_DEBUG is set, all pr_debug() and dev_dbg() calls
can be dynamically enabled/disabled on a per-module basis.
Future plans include extending this functionality to subsystems, that define
their own debug levels and flags.
Usage:
Dynamic debugging is controlled by the debugfs file,
<debugfs>/dynamic_printk/modules. This file contains a list of the modules that
can be enabled. The format of the file is as follows:
<module_name> <enabled=0/1>
.
.
.
<module_name> : Name of the module in which the debug call resides
<enabled=0/1> : whether the messages are enabled or not
For example:
snd_hda_intel enabled=0
fixup enabled=1
driver enabled=0
Enable a module:
$echo "set enabled=1 <module_name>" > dynamic_printk/modules
Disable a module:
$echo "set enabled=0 <module_name>" > dynamic_printk/modules
Enable all modules:
$echo "set enabled=1 all" > dynamic_printk/modules
Disable all modules:
$echo "set enabled=0 all" > dynamic_printk/modules
Finally, passing "dynamic_printk" at the command line enables
debugging for all modules. This mode can be turned off via the above
disable command.
[gkh: minor cleanups and tweaks to make the build work quietly]
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When enabling or disabling CONFIG_FTRACE_MCOUNT_RECORD, we want a full
kernel compile to handle the adding of the __mcount_loc sections.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to add a flag for all code that is in the drivers/staging/
directory to prevent all other kernel developers from worrying about
issues here, and to notify users that the drivers might not be as good
as they are normally used to.
Based on code from Andreas Gruenbacher and Jeff Mahoney to provide a
TAINT flag for the support level of a kernel module in the Novell
enterprise kernel release.
This is the kernel portion of this feature, the ability for the flag to
be set needs to be done in the build process and will happen in a
follow-up patch.
Cc: Andreas Gruenbacher <agruen@suse.de>
Cc: Jeff Mahoney <jeffm@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The idea is to add this to printk after the severity:
printk(KERN_ERR FW_BUG "This is not our fault, BIOS developer: fix it by
simply add ...\n");
If a Firmware issue should be hidden, because it is
work-arounded, but you still want to see something popping up e.g.
for info only:
printk(KERN_INFO FW_INFO "This is done stupid, we can handle it,
but it should better be avoided in future\n");
or on the Linuxfirmwarekit to tell vendors that they did something
stupid or wrong without bothering the user:
printk(KERN_INFO FW_BUG "This is done stupid, we can handle it,
but it should better be avoided in future\n");
Some use cases:
- If a user sees a [Firmware Bug] message in the kernel
he should first update the BIOS before wasting time with
debugging and submiting on old firmware code to mailing
lists.
- The linuxfirmwarekit (http://www.linuxfirmwarekit.org)
tries to detect firmware bugs. It currently is doing that
in userspace which results in:
- Huge test scripts that could be a one liner in the kernel
- A lot of BIOS bugs are already absorbed by the kernel
What do we need such a stupid linuxfirmwarekit for?
- Vendors: Can test their BIOSes for Linux compatibility.
There will be the time when vendors realize that the test utils
on Linux are more strict and using them increases the qualitity
and stability of their products.
- Vendors: Can easily fix up their BIOSes and be more Linux
compatible by:
dmesg |grep "Firmware Bug"
and send the result to their BIOS developer colleagues who should
know what the messages are about and how to fix them, without
the need of studying kernel code.
- Distributions: can do a first automated HW/BIOS checks.
This can then be done without the need of asking kernel developers
who need to dig down the code and explain the details.
Certification can/will just be rejected until
dmesg |grep "Firmware Bug" is empty.
- Thus this can be used as an instrument to enforce cleaner BIOS
code. Currently every stupid Windows ACPI bug is
re-implemented in Linux which is a rather unfortunate situation.
We already have the power to avoid this in e.g. memory
or cpu hot-plug ACPI implementations, because Linux certification
is a must for most vendors in the server area.
Working towards being able to do that in the laptop area
(vendors are starting to look at Linux here also and will use this tool)
is the goal. At least provide them a tool to make it as easy
for this guys (e.g. not needing to browse kernel code) as possible.
- The ordinary Linux user: can go into the next shop, boots the
firmwarekit on his most preferred machines. He chooses one without
BIOS bugs. Unsupported HW is ok, he likes to try out latest projects
which might support them or likes to dig on it on his own, but he
hates to workaround broken BIOSes like hell.
I double checked with the firmwarekit.
There they have:
So the mapping generally is (also depending on how likely the BIOS is
to blame, this could sometimes be difficult):
FW_INFO = INFO
FW_WARN = WARN
FW_BUG = FAIL
For more info about the linuxfirmwarekit and why this is needed
can be found here:
http://www.linuxfirmwarekit.org
While severity matches with the firmwarekit, it might be tricky
to hide messages from the user.
E.g. we recently found out that on HP BIOSes negative temperatures
are returned, which seem to indicate that the thermal zone is
invalid.
We can work around that gracefully by ignoring the thermal zone
and we do not want to bother the ordinary user with a frightening
message: Firmware Bug: thermal management absolutely broken
but want to hide it from the user.
But in the linuxfirmwarekit this should be shown as a real
show stopper (the temperatures could really be wrong,
broken thermal management is one of the worst things
that can happen and the BIOS guys of the machine must
implement this properly).
It is intended to do that (hide it from the user with
KERN_INFO msg, but still print it as a BIOS bug) by:
printk(KERN_INFO FW_BUG "Negativ temperature values detected.
Try to workarounded, BIOS must get fixed\n");
Hope that works out..., no idea how to better hide it
as printk is the only way to easily provide this functionality.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- unbreak ia64 (and powerpc) where function pointers dont
point at code but at data (reported by Tony Luck)
[ mingo@elte.hu: various cleanups ]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
include/linux/kernel.h: In function ‘printk_needs_cpu':
include/linux/kernel.h:217: error: parameter name omitted
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Avoid deadlocks against rq->lock and xtime_lock by deferring the klogd
wakeup by polling from the timer tick.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The file kernel.h contains the upper_32_bits macro. This patch adds the
other part, the lower_32_bits macro. Its first use will be in the driver
for AMD IOMMU.
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memparse()'s first argument can be const, so it should be.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All ratelimit user use same jiffies and burst params, so some messages
(callbacks) will be lost.
For example:
a call printk_ratelimit(5 * HZ, 1)
b call printk_ratelimit(5 * HZ, 1) before the 5*HZ timeout of a, then b will
will be supressed.
- rewrite __ratelimit, and use a ratelimit_state as parameter. Thanks for
hints from andrew.
- Add WARN_ON_RATELIMIT, update rcupreempt.h
- remove __printk_ratelimit
- use __ratelimit in net_ratelimit
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Needed to fix up a recursive include snafu in
locking-add-typecheck-on-irqsave-and-friends-for-correct-flags.patch
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These two macros are useful beyond lock debugging. Moved definitions from
include/linux/debug_locks.h to include/linux/kernel.h, so code that needs
them does not have to include the former, which would have been a less
intuitive choice of a header.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's not explicitly marked as asmlinkage, but invoked from x86_32
startup code with parameters on stack.
No other architectures define early_printk and none of them are affected
by this change, since defines asmlinkage as empty token.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a common hex array in hexdump.c so everyone can use it.
Add a common hi/lo helper to avoid the shifting masking that is
done to get the upper and lower nibbles of a byte value.
Pull the pack_hex_byte helper from kgdb as it is opencoded many
places in the tree that will be consolidated.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also, change the variable names used in the min/max macros to avoid shadowed
variable warnings when min/max min_t/max_t are nested.
Small formatting changes to make all the macros have a similar form.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix v4l build]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add definitions of USHORT_MAX and others into kernel. ipc uses it and slub
implementation might also use it.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Cc: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: "Pierre Peiffer" <peifferp@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to the rcupreempt.h WARN_ON trigged, I got 2G syslog file. For some
serious complaining of kernel, we need repeat the warnings, so here I isolate
the ratelimit part of printk.c to a standalone file.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel is sent to tainted within the warn_on_slowpath() function, and
whenever a warning occurs the new taint flag 'W' is set. This is useful to
know if a warning occurred before a BUG by preserving the warning as a flag
in the taint state.
This does not work on architectures where WARN_ON has its own definition.
These archs are:
1. s390
2. superh
3. avr32
4. parisc
The maintainers of these architectures have been added in the Cc: list
in this email to alert them to the situation.
The documentation in oops-tracing.txt has been updated to include the
new flag.
Signed-off-by: Nur Hussein <nurhussein@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When DEBUG is not defined, pr_debug and dev_dbg and some
other local debugging functions are specified as:
"inline __attribute__((format (printf, x, y)))"
This is done to validate printk arguments when not debugging.
Converting these functions to macros or statement expressions
"do { if (0) printk(fmt, ##arg); } while (0)"
or
"({ if (0) printk(fmt, ##arg); 0; })
makes at least gcc 4.2.2 produce smaller objects.
This has the additional benefit of allowing the optimizer to
avoid calling functions like print_mac that might have been
arguments to the printk.
defconfig x86 current:
$ size vmlinux
text data bss dec hex filename
4716770 474560 618496 5809826 58a6a2 vmlinux
all converted: (More patches follow)
$ size vmlinux
text data bss dec hex filename
4716642 474560 618496 5809698 58a622 vmlinux
Even kernel/sched.o, which doesn't even use these
functions, becomes smaller.
It appears that merely having an indirect include
of <linux/device.h> can cause bigger objects.
$ size sched.inline.o sched.if0.o
text data bss dec hex filename
31385 2854 328 34567 8707 sched.inline.o
31366 2854 328 34548 86f4 sched.if0.o
The current preprocessed only kernel/sched.i file contains:
# 612 "include/linux/device.h"
static inline __attribute__((always_inline)) int __attribute__ ((format (printf, 2, 3)))
dev_dbg(struct device *dev, const char *fmt, ...)
{
return 0;
}
# 628 "include/linux/device.h"
static inline __attribute__((always_inline)) int __attribute__ ((format (printf, 2, 3)))
dev_vdbg(struct device *dev, const char *fmt, ...)
{
return 0;
}
Removing these unused inlines from sched.i shrinks sched.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, for every sysfs node, the callers will be responsible for
implementing store operation, so many many callers are doing duplicate
things to validate input, they have the same mistakes because they are
calling simple_strtol/ul/ll/uul, especially for module params, they are
just numeric, but you can echo such values as 0x1234xxx, 07777888 and
1234aaa, for these cases, module params store operation just ignores
succesive invalid char and converts prefix part to a numeric although input
is acctually invalid.
This patch tries to fix the aforementioned issues and implements
strict_strtox serial functions, kernel/params.c uses them to strictly
validate input, so module params will reject such values as 0x1234xxxx and
returns an error:
write error: Invalid argument
Any modules which export numeric sysfs node can use strict_strtox instead of
simple_strtox to reject any invalid input.
Here are some test results:
Before applying this patch:
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000g > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000gggggggg > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 010000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0100008 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 010000aaaaa > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]#
After applying this patch:
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000g > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo 0x1000gggggggg > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# echo 010000 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# echo 0100008 > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# echo 010000aaaaa > /sys/module/e1000/parameters/copybreak
-bash: echo: write error: Invalid argument
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]# echo -n 4096 > /sys/module/e1000/parameters/copybreak
[root@yangyi-dev /]# cat /sys/module/e1000/parameters/copybreak
4096
[root@yangyi-dev /]#
[akpm@linux-foundation.org: fix compiler warnings]
[akpm@linux-foundation.org: fix off-by-one found by tiwai@suse.de]
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes an embedded image a bit smaller.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suppress A.OUT library support if CONFIG_ARCH_SUPPORTS_AOUT is not set.
Not all architectures support the A.OUT binfmt, so the ELF binfmt should not
be permitted to go looking for A.OUT libraries to load in such a case. Not
only that, but under such conditions A.OUT core dumps are not produced either.
To make this work, this patch also does the following:
(1) Makes the existence of the contents of linux/a.out.h contingent on
CONFIG_ARCH_SUPPORTS_AOUT.
(2) Renames dump_thread() to aout_dump_thread() as it's only called by A.OUT
core dumping code.
(3) Moves aout_dump_thread() into asm/a.out-core.h and makes it inline. This
is then included only where needed. This means that this bit of arch
code will be stored in the appropriate A.OUT binfmt module rather than
the core kernel.
(4) Drops A.OUT support for Blackfin (according to Mike Frysinger it's not
needed) and FRV.
This patch depends on the previous patch to move STACK_TOP[_MAX] out of
asm/a.out.h and into asm/processor.h as they're required whether or not A.OUT
format is available.
[jdike@addtoit.com: uml: re-remove accidentally restored code]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an ACPI table is overridden (for now this can happen only for DSDT)
display a big warning and taint the kernel with flag A.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Len Brown <len.brown@intel.com>
I was happy to discover the brand new IS_ALIGN macro and quickly used it in
my code. To my dismay I found that the generated code used division to
perform the test.
This patch fixes it by changing the % test to an &. This avoids the
division.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Why do we even have cond_resched when real preemption
is on? It seems to be a waste of space and time.
remove cond_resched with CONFIG_PREEMPT on.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
printk: add the KERN_CONT annotation (which is empty string but via
which checkpatch.pl can notice that the lacking KERN_ level is fine).
This useful for multiple calls of hand-crafted printk output done by
early debug code or similar.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Other/Some pr_*() macros are already defined in kernel.h, but pr_err() was
defined multiple times in several other places
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Tony Lindgren <tony@atomide.com>
Reviewed-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two new functions for reading the kernel log buffer. The intention is for
them to be used by recovery/dump/debug code so the kernel log can be easily
retrieved/parsed in a crash scenario, but they are generic enough for other
people to dream up other fun uses.
[akpm@linux-foundation.org: buncha fixes]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Robin Getz <rgetz@blackfin.uclinux.org>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Logic.
- set all pages in [start,end) as isolated migration-type.
by this, all free pages in the range will be not-for-use.
- Migrate all LRU pages in the range.
- Test all pages in the range's refcnt is zero or not.
Todo:
- allocate migration destination page from better area.
- confirm page_count(page)== 0 && PageReserved(page) page is safe to be freed..
(I don't like this kind of page but..
- Find out pages which cannot be migrated.
- more running tests.
- Use reclaim for unplugging other memory type area.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AdvanSys driver wants to align some pointers, and the ALIGN macro
doesn't work for pointers. Rather than try to make it work, add a new
PTR_ALIGN macro which is typesafe.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial fix: mark the buffer to hexdump as const so callers could avoid
casting their const buffers when calling print_hex_dump().
The patch is really trivial and I suggest to consider it as a fix
(it fixes GCC warnings) and push it to current tree.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc 4.3 supports a new __attribute__((__cold__)) to mark functions cold. Any
path directly leading to a call of this function will be unlikely. And gcc
will try to generate smaller code for the function itself.
Please use with care. The code generation advantage isn't large and in most
cases it is not worth uglifying code with this.
This patch marks some common error functions like panic(), printk()
as cold. This will longer term make many unlikely()s unnecessary, although
we can keep them for now for older compilers.
BUG is not marked cold because there is currently no way to tell
gcc to mark a inline function told.
Also all __init and __exit functions are marked cold. With a non -Os
build this will tell the compiler to generate slightly smaller code
for them. I think it currently only uses less alignments for labels,
but that might change in the future.
One disadvantage over *likely() is that they cannot be easily instrumented
to verify them.
Another drawback is that only the latest gcc 4.3 snapshots support this.
Unfortunately we cannot detect this using the preprocessor. This means older
snapshots will fail now. I don't think that's a problem because they are
unreleased compilers that nobody should be using.
gcc also has a __hot__ attribute, but I don't see any sense in using
this in the kernel right now. But someday I hope gcc will be able
to use more aggressive optimizing for hot functions even in -Os,
if that happens it should be added.
Includes compile fix from Thomas Gleixner.
Cc: Jan Hubicka <jh@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a prefix string parameter. Callers are responsible for any string
length/alignment that they want to see in the output. I.e., callers should
pad strings to achieve alignment if they want that.
Add rowsize parameter. This is the number of raw data bytes to be printed
per line. Must be 16 or 32.
Add a groupsize parameter. This allows callers to dump values as 1-byte,
2-byte, 4-byte, or 8-byte numbers. Default is 1-byte numbers. If the
total length is not an even multiple of groupsize, 1-byte numbers are
printed.
Add an "ascii" output parameter. This causes ASCII data output following
the hex data output.
Clean up some doc examples.
Align the ASCII output on all lines that are produced by one call.
Add a new interface, print_hex_dump_bytes(), that is a shortcut to
print_hex_dump(), using default parameter values to print 16 bytes in
byte-size chunks of hex + ASCII output, using printk level KERN_DEBUG.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding tabs where spaces currently are.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on ace_dump_mem() from Grant Likely for the Xilinx SystemACE
CompactFlash interface.
Add print_hex_dump() & hex_dumper() to lib/hexdump.c and linux/kernel.h.
This patch adds the functions print_hex_dump() & hex_dumper().
print_hex_dump() can be used to perform a hex + ASCII dump of data to
syslog, in an easily viewable format, thus providing a common text hex dump
format.
hex_dumper() provides a dump-to-memory function. It converts one "line" of
output (16 bytes of input) at a time.
Example usages:
print_hex_dump(KERN_DEBUG, DUMP_PREFIX_ADDRESS, frame->data, frame->len);
hex_dumper(frame->data, frame->len, linebuf, sizeof(linebuf));
Example output using %DUMP_PREFIX_OFFSET:
0009ab42: 40414243 44454647 48494a4b 4c4d4e4f-@ABCDEFG HIJKLMNO
Example output using %DUMP_PREFIX_ADDRESS:
ffffffff88089af0: 70717273 74757677 78797a7b 7c7d7e7f-pqrstuvw xyz{|}~.
[akpm@linux-foundation.org: cleanups, add export]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We keep on getting "right shift count >= width of type" warnings when doing
things like
sector_t s;
x = s >> 56;
because with CONFIG_LBD=n, s is only 32-bit. Similar problems can occur with
dma_addr_t's.
So add a simple wrapper function which code can use to avoid this warning.
The above example would become
x = upper_32_bits(s) >> 24;
The first user is in fact AFS.
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: "Cameron, Steve" <Steve.Cameron@hp.com>
Cc: "Miller, Mike (OS Dev)" <Mike.Miller@hp.com>
Cc: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can use a gcc extension to ensure that ARRAY_SIZE() is handed an array,
not a pointer. This is especially important when code is changed from a
fixed array to a pointer. I assume the Intel compiler doesn't support
__builtin_types_compatible_p.
[jdike@addtoit.com: uml: update UML definition of ARRAY_SIZE]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a kvasprintf() function to complement kasprintf().
No in-tree users yet, but I have some coming up.
[akpm@linux-foundation.org: EXPORT it]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To properly implement a pid namespace I need to deal exclusively in terms of
struct pid, because pid_t values become ambiguous.
To this end session_of_pgrp is transformed to take and return a struct pid
pointer. To avoid the need to worry about reference counting I now require my
caller to hold the appropriate locks. Leaving callers repsonsible for
increasing the reference count if they need access to the result outside of
the locks.
Since session_of_pgrp currently only has one caller and that caller simply
uses only test the result for equality with another process group, the locking
change means I don't actually have to acquire the tasklist_lock at all.
tiocspgrp is also modified to take and release the lock. The logic there is a
little more complicated but nothing I won't need when I convert pgrp of a tty
to a struct pid pointer.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove labs() since it is not used/needed.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that almost all architectures implemented exactly the same
sys32_sysinfo... except parisc, where a bug was to be found in handling of
the uptime. So let's remove a whole whack of code for fun and profit.
Cribbed compat_sys_sysinfo from x86_64's implementation, since I figured it
would be the best tested.
This patch incorporates Arnd's suggestion of not using set_fs/get_fs, but
instead extracting out the common code from sys_sysinfo.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow taint flags to be set from userspace by writing to
/proc/sys/kernel/tainted, and add a new taint flag, TAINT_USER, to be used
when userspace has potentially done something dangerous that might
compromise the kernel. This will allow support personnel to ask further
questions about what may have caused the user taint flag to have been set.
For example, they might examine the logs of the realtime JVM to see if the
Java program has used the really silly, stupid, dangerous, and
completely-non-portable direct access to physical memory feature which MUST
be implemented according to the Real-Time Specification for Java (RTSJ).
Sigh. What were those silly people at Sun thinking?
[akpm@osdl.org: build fix]
[bunk@stusta.de: cleanup]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert previous attempts at messing with the linux banner string and
simply use a separate format string for proc.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As reported by Andy Whitcroft, at least the SLES9 initrd build process
depends on getting the kernel version from the kernel binary. It does
that by simply trawling the binary and looking for the signature of the
"linux_banner" string (the string "Linux version " to be exact. Which
is really broken in itself, but whatever..)
That got broken when the string was changed to allow /proc/version to
change the UTS release information dynamically, and "get_kernel_version"
thus returned "%s" (see commit a2ee8649ba6d71416712e798276bf7c40b64e6e5:
"[PATCH] Fix linux banner utsname information").
This just restores "linux_banner" as a static string, which should fix
the version finding. And /proc/version simply uses a different string.
To avoid wasting even that miniscule amount of memory, the early boot
string should really be marked __initdata, but that just causes the same
bug in SLES9 to re-appear, since it will then find other occurrences of
"Linux version " first.
Cc: Andy Whitcroft <apw@shadowen.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Steve Fox <drfickle@us.ibm.com>
Acked-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alter roundup_pow_of_two() so that it can make use of ilog2() on a constant to
produce a constant value, retaining the ability for an arch to override it in
the non-const case.
This permits the function to be used to initialise variables.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
You wouldn't think that doing an ALIGN() macro that aligns something up
to a power-of-two boundary would be likely to have bugs, would you?
But hey, in the wonderful world of mixing integer types, you have to be
careful. This just makes sure that the alignment is interpreted in the
same type as the thing to be aligned.
Thanks to Roland Dreier, who noticed that the amso1100 driver got broken
by the previous fix (that just extended the mask to "unsigned long", but
was still broken in "unsigned long long" - it just happened to be the
same on 64-bit architectures).
See commit 4c8bd7eeee for the history of
bugs here...
Acked-by: Roland Dreier <rdreier@cisco.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: David Miller <davem@davemloft.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk_ratelimit() has global state which makes it not useful for callers
which wish to perform ratelimiting at a particular frequency.
Add a printk_timed_ratelimit() which utilises caller-provided state storage to
permit more flexibility.
This function can in fact be used for things other than printk ratelimiting
and is perhaps poorly named.
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check pr_debug() arguments
When DEBUG isn't defined pr_debug() is defined away as an empty macro. By
throwing away the arguments we allow completely incorrect code to build.
Instead let's make it an empty inline which checks arguments and mark it so gcc
can check the format specification.
This results in a seemingly insignificant code size increase. A x86-64
allyesconfig:
text data bss dec hex filename
25354768 7191098 4854720 37400586 23ab00a vmlinux.before
25354945 7191138 4854720 37400803 23ab0e3 vmlinux
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The NUMA_BUILD constant is always available and will be set to 1 on
NUMA_BUILDs. That way checks valid only under CONFIG_NUMA can easily be done
without #ifdef CONFIG_NUMA
F.e.
if (NUMA_BUILD && <numa_condition>) {
...
}
[akpm: not a thing we'd normally do, but CONFIG_NUMA is special: it is
causing ifdef explosion in core kernel, so let's see if this is a comfortable
way in whcih to control that]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (225 commits)
[PATCH] Don't set calgary iommu as default y
[PATCH] i386/x86-64: New Intel feature flags
[PATCH] x86: Add a cumulative thermal throttle event counter.
[PATCH] i386: Make the jiffies compares use the 64bit safe macros.
[PATCH] x86: Refactor thermal throttle processing
[PATCH] Add 64bit jiffies compares (for use with get_jiffies_64)
[PATCH] Fix unwinder warning in traps.c
[PATCH] x86: Allow disabling early pci scans with pci=noearly or disallowing conf1
[PATCH] x86: Move direct PCI scanning functions out of line
[PATCH] i386/x86-64: Make all early PCI scans dependent on CONFIG_PCI
[PATCH] Don't leak NT bit into next task
[PATCH] i386/x86-64: Work around gcc bug with noreturn functions in unwinder
[PATCH] Fix some broken white space in ia32_signal.c
[PATCH] Initialize argument registers for 32bit signal handlers.
[PATCH] Remove all traces of signal number conversion
[PATCH] Don't synchronize time reading on single core AMD systems
[PATCH] Remove outdated comment in x86-64 mmconfig code
[PATCH] Use string instructions for Core2 copy/clear
[PATCH] x86: - restore i8259A eoi status on resume
[PATCH] i386: Split multi-line printk in oops output.
...
Add the DIV_ROUND_UP() helper macro: divide `n' by `d', rounding up.
Stolen from the gfs2 tree(!) because the swsusp patches need it.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To quote Alan Cox:
The default Linux behaviour on an NMI of either memory or unknown is to
continue operation. For many environments such as scientific computing
it is preferable that the box is taken out and the error dealt with than
an uncorrected parity/ECC error get propogated.
A small number of systems do generate NMI's for bizarre random reasons
such as power management so the default is unchanged. In other respects
the new proc/sys entry works like the existing panic controls already in
that directory.
This is separate to the edac support - EDAC allows supported chipsets to
handle ECC errors well, this change allows unsupported cases to at least
panic rather than cause problems further down the line.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
pr_debug() should not be used from drivers, add comment saying that.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the roundup() macro from binfmt_elf.c into linux/kernel.h as it's
generally useful.
[akpm@osdl.org: nuke all the other implementations]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These are the generic bits needed to enable reliable stack traces based
on Dwarf2-like (.eh_frame) unwind information. Subsequent patches will
enable x86-64 and i386 to make use of this.
Thanks to Andi Kleen and Ingo Molnar, who pointed out several possibilities
for improvement.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement kasprintf, a kernel version of asprintf. This allocates the
memory required for the formatted string, including the trailing '\0'.
Returns NULL on allocation failure.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The likely() profiling tools show that __alloc_page() causes a lot of misses:
! 132 119193 __alloc_pages():mm/page_alloc.c@937
Because most __alloc_page() calls are not atomic.
Signed-off-by: Hua Zhong <hzhong@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a writeback_control's `start' and `end' fields are used to
indicate a one-byte-range starting at file offset zero, the required
values of .start=0,.end=0 mean that the ->writepages() implementation
has no way of telling that it is being asked to perform a range
request. Because we're currently overloading (start == 0 && end == 0)
to mean "this is not a write-a-range request".
To make all this sane, the patch changes range of writeback_control.
So caller does: If it is calling ->writepages() to write pages, it
sets range (range_start/end or range_cyclic) always.
And if range_cyclic is true, ->writepages() thinks the range is
cyclic, otherwise it just uses range_start and range_end.
This patch does,
- Add LLONG_MAX, LLONG_MIN, ULLONG_MAX to include/linux/kernel.h
-1 is usually ok for range_end (type is long long). But, if someone did,
range_end += val; range_end is "val - 1"
u64val = range_end >> bits; u64val is "~(0ULL)"
or something, they are wrong. So, this adds LLONG_MAX to avoid nasty
things, and uses LLONG_MAX for range_end.
- All callers of ->writepages() sets range_start/end or range_cyclic.
- Fix updates of ->writeback_index. It seems already bit strange.
If it starts at 0 and ended by check of nr_to_write, this last
index may reduce chance to scan end of file. So, this updates
->writeback_index only if range_cyclic is true or whole-file is
scanned.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: "Vladimir V. Saveliev" <vs@namesys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Even since a previous patch:
Fix race between CONFIG_DEBUG_SLABALLOC and modules
Sun, 27 Jun 2004 17:55:19 +0000 (17:55 +0000)
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/old-2.6-bkcvs.git;a=commit;h=92b3db26d31cf21b70e3c1eadc56c179506d8fbe
The function symbol_put_addr() will deadlock the kernel.
symbol_put_addr() would acquire modlist_lock, then while holding the lock call
two functions kernel_text_address() and module_text_address() which also try
to acquire the same lock. This deadlocks the kernel of course.
This patch changes symbol_put_addr() to not acquire the modlist_lock, it
doesn't need it since it never looks at the module list directly. Also, it
now uses core_kernel_text() instead of kernel_text_address(). The latter has
an additional check for addr inside a module, but we don't need to do that
since we call module_text_address() (the same function kernel_text_address
uses) ourselves.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Cc: Zwane Mwaikambo <zwane@fsmlabs.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the scheduled unexport of panic_timeout.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fls() takes an integer, so roundup_pow_of_two() is busted for ulongs larger
than 2^32-1.
Fix this by implementing and using fls_long().
(Why does roundup_pow_of_two() return a long?)
(Why is roundup_pow_of_two() __attribute_const__ whereas long_log2() is
__attribute_pure__?)
(Why does long_log2() suck so much? Because we were missing fls_long()?)
Cc: Roland Dreier <rdreier@cisco.com>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Cc: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attempt to fix the problem wherein people's oops reports scroll off the screen
due to repeated oopsing or to oopses on other CPUs.
If this happens the user can reboot with the `pause_on_oops=<seconds>' option.
It will allow the first oopsing CPU to print an oops record just a single
time. Second oopsing attempts, or oopses on other CPUs will cause those CPUs
to enter a tight loop until the specified number of seconds have elapsed.
The patch implements the infrastructure generically in the expectation that
architectures other than x86 will find it useful.
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD SimNow!'s JIT doesn't like them at all in the guest. For distribution
installation it's easiest if it's a boot time option.
Also I moved the variable to a more appropiate place and make
it independent from sysctl
And marked __read_mostly which it is.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Procfs always output IPV6 addresses without the colon
characters, and we cannot change that.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are errors and inconsistency in the display of NIP6 strings.
ie: net/ipv6/ip6_flowlabel.c
There are errors and inconsistency in the display of NIPQUAD strings too.
ie: net/netfilter/nf_conntrack_ftp.c
This patch:
adds NIP6_FMT to kernel.h
changes all code to use NIP6_FMT
fixes net/ipv6/ip6_flowlabel.c
adds NIPQUAD_FMT to kernel.h
fixes net/netfilter/nf_conntrack_ftp.c
changes a few uses of "%u.%u.%u.%u" to NIPQUAD_FMT for symmetry to NIP6_FMT
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
)
From: Adrian Bunk <bunk@stusta.de>
- create one common dump_thread() prototype in kernel.h
- dump_thread() is only used in fs/binfmt_aout.c and can therefore be
removed on all architectures where CONFIG_BINFMT_AOUT is not
available
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add typecheck_fn(type, function) to do type-checking of function
pointers.
Modified-by: Ingo Molnar <mingo@elte.hu>
(made it typeof() based, instead of typedef based.)
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove various things which were checking for gcc-1.x and gcc-2.x compilers.
From: Adrian Bunk <bunk@stusta.de>
Some documentation updates and removes some code paths for gcc < 3.2.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://bugzilla.kernel.org/show_bug.cgi?id=4320
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This looks like something which out-of-tree code could possibly be using.
Give panic_timeout the twelve-month treatment.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert to proper kernel-doc format.
Some have extra blank lines (not allowed immed. after the function name)
or need blank lines (after all parameters). Function summary must be only
one line.
Colon (":") in a function description does weird things (causes kernel-doc
to think that it's a new section head sadly).
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Force a compiler error instead of a link error, because they are easier to
track down. Idea stolen from code by Jan Beulich <jbeulich@novell.com>
If the argument to BUILD_BUG_ON evaluates to non-zero the compiler will do:
t.c:6: error: size of array `type name' is negative
(surprised that gcc doesn't have an extension for this)
Signed-off-by: "Andi Kleen" <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new preemption model: 'Voluntary Kernel Preemption'. The
3 models can be selected from a new menu:
(X) No Forced Preemption (Server)
( ) Voluntary Kernel Preemption (Desktop)
( ) Preemptible Kernel (Low-Latency Desktop)
we still default to the stock (Server) preemption model.
Voluntary preemption works by adding a cond_resched()
(reschedule-if-needed) call to every might_sleep() check. It is lighter
than CONFIG_PREEMPT - at the cost of not having as tight latencies. It
represents a different latency/complexity/overhead tradeoff.
It has no runtime impact at all if disabled. Here are size stats that show
how the various preemption models impact the kernel's size:
text data bss dec hex filename
3618774 547184 179896 4345854 424ffe vmlinux.stock
3626406 547184 179896 4353486 426dce vmlinux.voluntary +0.2%
3748414 548640 179896 4476950 445016 vmlinux.preempt +3.5%
voluntary-preempt is +0.2% of .text, preempt is +3.5%.
This feature has been tested for many months by lots of people (and it's
also included in the RHEL4 distribution and earlier variants were in Fedora
as well), and it's intended for users and distributions who dont want to
use full-blown CONFIG_PREEMPT for one reason or another.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange for all kernel printks to be no-ops. Only available if
CONFIG_EMBEDDED.
This patch saves about 375k on my laptop config and nearly 100k on minimal
configs.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Frederic Weisbecker
Kurt Garloff
Bartlomiej Zolnierkiewicz
Linus Torvalds
GeunSik Lim
Michael Ellerman
Neil Horman
Ingo Molnar
Cyrill Gorcunov
Harvey Harrison
Greg Banks
Jason Baron
Steven Rostedt
Peter Zijlstra
Wu Fengguang
Darrick J. Wong
Cornelia Huck
David S. Miller
Martin Schwidefsky
Randy Dunlap
Len Brown
Andi Kleen
Steven Rostedt
Greg Kroah-Hartman
Thomas Renninger
Nick Piggin
Arjan van de Ven
Uwe Kleine-König
Peter Zijlstra
Joerg Roedel
Jeremy Fitzhardinge
Dave Young
Andrew Morton
Eduard - Gabriel Munteanu
Jiri Slaby
Thomas Gleixner
Zhang, Yanmin
Nur Hussein
Joe Perches
Yi Yang
David Howells
Éric Piel
Herbert Xu
Emil Medve
Mike Frysinger
KAMEZAWA Hiroyuki
Jens Axboe
Matthew Wilcox
Alan Stern
Artem Bityutskiy
Andi Kleen
Pavel Emelianov
Daniel Walker
Rusty Russell
Eric W. Biederman
Richard Knutsson
Kirill Korotaev
Kyle McMartin
Theodore Ts'o
Roman Zippel
Linus Torvalds
Jim Cromie
Andrew Morton
Zach Brown
Christoph Lameter
Linus Torvalds
Steven Whitehouse
Don Zickus
Pavel Machek
Jan Beulich
Jeremy Fitzhardinge
Hua Zhong
OGAWA Hirofumi
Trent Piepho
Adrian Bunk
YOSHIFUJI Hideaki
Chuck Ebbert
Alexey Starikovskiy
Randy Dunlap
Nikita Danilov
Matt Mackall
Linus Torvalds