General driver churn doesn't always include updates of header includes.
Manual review of the output of the include-what-you-use checker lead to the
following cleanup. Hopefuly this brings things back to a good state for the
hid-sensor drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210608205510.4033887-1-jic23@kernel.org
A namespace for exported symbols makes clear who is a provider
and who is a consumer of the certain resources. Besides that,
it doesn't pollute the common namespace.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210614162447.5392-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Converts from using pm_runtime_get_sync() with no error handling over
to pm_runtime_resume_and_get() which will ensure we don't end up
holding a reference. Ensure this error return is then handled at
calls to mlx90614_power_get(). These are all direct returns.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210509113354.660190-25-jic23@kernel.org
TMP117 is a Digital temperature sensor with integrated Non-Volatile memory.
Add support for tmp117 driver in iio subsystem.
Datasheet: https://www.ti.com/lit/gpn/tmp117
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210407182147.77221-3-puranjay12@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
During commit 067fda1c06 ("iio: hid-sensors: move triggered buffer
setup into hid_sensor_setup_trigger"), the
iio_triggered_buffer_{setup,cleanup}() functions got moved under the
hid-sensor-trigger module.
The above change works fine, if any of the sensors get built. However, when
only the common hid-sensor-trigger module gets built (and none of the
drivers), then the IIO_TRIGGERED_BUFFER symbol isn't selected/enforced.
Previously, each driver would enforce/select the IIO_TRIGGERED_BUFFER
symbol. With this change the HID_SENSOR_IIO_TRIGGER (for the
hid-sensor-trigger module) will enforce that IIO_TRIGGERED_BUFFER gets
selected.
All HID sensor drivers select the HID_SENSOR_IIO_TRIGGER symbol. So, this
change removes the IIO_TRIGGERED_BUFFER enforcement from each driver.
Fixes: 067fda1c06 ("iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger")
Reported-by: Thomas Deutschmann <whissi@gentoo.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210414084955.260117-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
-----BEGIN PGP SIGNATURE-----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=jeRJ
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st set of IIO/counter device support, features and cleanup in the 5.13 cycle
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
* tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (119 commits)
iio: acpi_als: Add trigger support
iio: acpi_als: Add local variable dev in probe
iio: acpi_als: Add timestamp channel
iio: adc: ad7292: Modify the bool initialization assignment
iio: cros: unify hw fifo attributes without API changes
iio: kfifo: add devm_iio_triggered_buffer_setup_ext variant
iio: event_monitor: Enable events before monitoring
dt-bindings: iio: adc: Add compatible for Mediatek MT8195
iio:magnetometer: Add Support for ST IIS2MDC
dt-bindings: iio: st,st-sensors add IIS2MDC.
staging: iio: ad9832: kernel-doc fixes
iio:dac:max517.c: Use devm_iio_device_register()
iio:cros_ec_sensors: Fix a wrong function name in kernel doc.
iio: buffer: kfifo_buf: kernel-doc, typo in function name.
iio: accel: sca3000: kernel-doc fixes. Missing - and wrong function names.
iio: adc: adi-axi-adc: Drop false marking for kernel-doc
iio: adc: cpcap-adc: kernel-doc fix - that should be _ in structure name
iio: dac: ad5504: fix wrong part number in kernel-doc structure name.
iio: dac: ad5770r: kernel-doc fix case of letter R wrong in structure name
iio: adc: ti-adc084s021: kernel-doc fixes, missing function names
...
This change converts the driver to use device-managed functions in the
probe function. The power-down call is handled now via a
devm_add_action_or_reset() hook, and then devm_iio_device_register() can be
used to register the IIO device.
The final aim here would be for IIO to export only the device-managed
functions of it's API. That's a long way to go and this a small step in
that direction.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210310093800.45822-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No functional change has been made with this patch. The main intent here
is to reduce code repetition of getting sensitivity attribute.
In the current implementation, sensor_hub_input_get_attribute_info() is
called from multiple drivers to get attribute info for sensitivity
field. Moving this to common place will avoid code repetition.
Signed-off-by: Ye Xiang <xiang.ye@intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210201054921.18214-2-xiang.ye@intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes 2 issues of timestamp channel:
1. This patch ensures that there is sufficient space and correct
alignment for the timestamp.
2. Correct the timestamp channel scan index.
Fixes: 59d0f2da35 ("iio: hid: Add temperature sensor support")
Signed-off-by: Ye Xiang <xiang.ye@intel.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303063615.12130-4-xiang.ye@intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After an I2C reset command, the mlx90632 needs some time before
responding to other I2C commands. Without that delay, there is a chance
that the I2C command(s) after the reset will not be accepted.
Signed-off-by: Slaveyko Slaveykov <sis@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Fixes: e02472f74a ("iio:temperature:mlx90632: Adding extended calibration option")
Link: https://lore.kernel.org/r/20201216115720.12404-2-sis@melexis.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When returning or breaking early from a
`for_each_available_child_of_node()` loop, we need to explicitly call
`of_node_put()` on the child node to possibly release the node.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200925091045.302-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This prevents use of this driver with ACPI via PRP0001 and is
an example of an anti pattern I'm trying to remove from IIO.
Hence drop from this driver.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <manivannanece23@gmail.com>
Link: https://lore.kernel.org/r/20200910173242.621168-23-jic23@kernel.org
This prevents use of this driver with ACPI via PRP0001 and is
an example of an anti pattern I'm trying to remove from IIO.
Hence drop from this driver.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Link: https://lore.kernel.org/r/20200910173242.621168-22-jic23@kernel.org
Since object temperature might be different than the sensor temperature
the infrared sensors should provide an interface to inject ambient
temperature. This was in past done via write to ambient temperature
interface (in_temp_ambient_raw), but I think most people did not know
about it. This solution introduces a new iio type of the CALIBAMBIENT
which is hopefully more descriptive and more explicit about the purpose
and capabilities of the sensors.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200906210231.383976-1-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is some inconsistency and whitespace cleanup performed in this
patch. It was done on top of my other patches, but I can rebase to head
of the togreg branch if it would go in sooner.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-6-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For some time the market wants medical grade accuracy in medical range,
while still retaining the declared accuracy outside of the medical range
within the same sensor. That is why we created extended calibration
which is automatically switched to when object temperature is too high.
This patch also introduces the object_ambient_temperature variable which
is needed for more accurate calculation of the object infra-red
footprint as sensor's ambient temperature might be totally different
than what the ambient temperature is at object and that is why we can
have some more errors which can be eliminated. Currently this temperature
is fixed at 25, but the interface to adjust it by user (with external
sensor or just IR measurement of the other object which acts as ambient),
will be introduced in another commit.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-5-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce number of lines and improve readability to convert polling while
loops to regmap_read_poll_timeout.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-4-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document internal/private struct for mlx90632 device.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-3-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
TAdut4 was calculated each iteration although it did not change. In light
of near future additions of the Extended range DSP calculations, this
function refactoring will help reduce unrelated changes in that series as
well as reduce the number of new functions needed.
Signed-off-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200818213737.140613-2-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'*'s are not welcome in kerneldoc parameter names.
Fixes the following W=1 kernel build warning(s):
drivers/iio/temperature/mlx90632.c:175: warning: Function parameter or member 'data' not described in 'mlx90632_perform_measurement'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If a driver does not assign an of_node to a IIO device to IIO core will
automatically assign the of_node of the parent device. This automatic
assignment is done in the iio_device_register() function.
There is a fair amount of drivers that currently manually assign the
of_node of the IIO device. All but 4 of them can make use of the automatic
assignment though.
The exceptions are:
* mxs-lradc-adc: Which uses the of_node of the parent of the parent.
* stm32-dfsdm-adc, stm32-adc and stm32-dac: Which reference the of_node
assigned to the IIO device before iio_device_register() is called.
All other drivers are updated to use automatic assignment. This reduces
the amount of boilerplate code involved in setting up the IIO device.
The patch has mostly been auto-generated with the following semantic patch
// <smpl>
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(&parent, ...)
...
-indio_dev->dev.of_node = parent.of_node;
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(parent, ...)
...
-indio_dev->dev.of_node = parent->of_node;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were found by doing some shell magic:
------------
for file in $(git grep -w devm_iio_device_alloc | cut -d: -f1 | sort | uniq) ; do
if grep 'parent =' $file | grep -v trig | grep -vq devm_; then
echo "$file -> $(grep "parent =" $file)"
fi
done
-----------
The output is bearable [after the semantic patch is applied].
There is a mix of trigger assignments with some iio device parent
assignments that are removed via this patch.
JC: A few more added via inspection of all parent =
statements in drivers/iio. Some of these may just have crossed with this
series, others were less obvious to scripting due to some cross
file / module boundary calls.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;
It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'
But this is is only done in case where the block is left empty.
The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.
However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The main intent here is to get rid of the iio_buffer_set_attrs() helper, or
at least rework it's usage a bit.
The problem with that helper is that it needs a pointer to the buffer,
which makes supporting multiple buffers per IIO device a bit more
cumbersome.
The hid_sensor_setup_trigger() is pretty much used in the same way:
- iio_triggered_buffer_setup() gets called before
- then hid_sensor_setup_trigger() and hid_sensor_setup_batch_mode() gets
called which may attach some fifo attributes
This change merges the 2 together under the hid_sensor_setup_trigger()
function. Only the &iio_pollfunc_store_time is passed to all devices, so
it's not even required to pass it explicitly outside of the common
hid_sensor_setup_trigger() function.
Moving the devm_iio_triggered_buffer_setup/cleanup() calls into the common
place code can help the rework of the buffer code, since it is in one
place.
One detail of the change is that there are 2 drivers that use
devm_iio_triggered_buffer_setup(). That function gets implicitly
replaced with iio_triggered_buffer_setup()/cleanup(), but since all drivers
call both hid_sensor_setup_trigger9) & hid_sensor_remove_trigger() trigger,
the iio_triggered_buffer_cleanup() piggy backs on the
hid_sensor_remove_trigger() call, which should cover the cleanup.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
-----BEGIN PGP SIGNATURE-----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=DyTF
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
This patch adds support for the Azoteq IQS620AT temperature sensor,
capable of reporting its absolute die temperature.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
-----BEGIN PGP SIGNATURE-----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=8FmM
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.6 cycle
New device support
* ad7091r5 ADC
- New driver with follow up patch adding scale and vref support.
- DT bindings
* ad7923
- Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
- Support the BMA254 accelerometer. Required fairly substantial rework
to allow for small differences between this an existing parts.
* bma400 accelerometer
- New driver with follow up patch for regulator support.
- DT bindings.
* asc dlhl60d
- New driver support this range of pressure and temperature sensors.
- DT bindings.
* ltc2496 ADC
- New driver to support this ADC.
- Split the existing LTC2497 driver generic component out and reuse.
- DT bindings.
* parallax ping
- New driver supporting ultrasonic and laser tof distance sensors.
- Bindings for these sensors.
New features
* core
- New char type for read_raw returns, used for thermocouple types.
- Rename read_first_n callback to read. The reasons behind the original
naming are lost to the mists of time.
* ad799x
- Allow pm_ops to disable device completely allowing regulator power down.
* bma180
- Enable basic regulator support.
* dmaengine buffer
- Report platform data alignment requirements via new ABI.
* max31856
- Add option to set mains filter rejection frequency and document
new in_temp_filter_notch_center_frequency ABI.
- Add support for configuring HW averaging (oversampling ratio)
- Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
- Add read only access to thermocouple type using new ABI, includes
adding more specific compatibles to reflect which variant of the
chip is being used.
* mpu6050
- Provide option to support the PMU9150 in package magnetometer directly
rather than via auxiliary bus.
* stm32_adc
- Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
- Enable the sensor-hub support for lsm6dsm. Includes various reworks to
allow this.
Cleanups and minor fixes
* Subsystem wide
- Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
- Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
- Convert to GPIO descriptors.
* ad7303
- Avoid a dance with checking if the regulator is supplied by just
using the optional request interface.
* ad7887
- Simplify channel specification assignment to enable adding more devices.
* ad7923
- Drop some unused and largely pointless defines of BOB_N==N variety.
- Tidy up checkpatch warnings.
- Add missing of_device_id table.
* adf4350
- Convert to GPIO descriptors.
* ak8975
- Convert to GPIO descriptors.
* ADIS library and drivers
- Expand scope of txrx_lock to cover all state and rename as state_lock
- Add unlocked read / write to allow grouping of consecutive calls under
single lock / unlock.
- Add unlocked check_status, reset to allow grouping under single
lock / unlock.
- Remove remaining uses of core mlock for local state protection.
mlock should never be used directly as it protects tightly defined
core IIO device management state.
* adis16240
- Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
- Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
- Use local dev variable to tidy up code.
- Use c99 style explicity .member assignment to make driver more readable.
* bmp280
- Drop ACPI support. No evidence this was used and appropriate ID is not
registered.
- Allow ACPI to bind device via PRP0001
* dmaengine buffer
- Use dma_request_chan instead of dma_request_slave_channel_reason as that
ABI is going away.
- Add module info to avoid tainting the kernel.
* hts221
- Avoid magic number defines when only used to fill structure elements
that are self describing.
* lm3533
- Drop a stray semicolon.
* max9611
- Cleanup enum handling to be more resilient to future changes.
* mpu6050
- Delete MPU9150 from supported SPI devices as doesn't provide SPI.
- Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
- Drop an unnecessary register update.
* ssp_sensors
- Convert to GPIO descriptors.
* st_sensors
- drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
anyway.
- Make default platform data structures __maybe_unsued.
- Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
- white space fixes.
- Mark some constants that aren't always used as __maybe_unused.
- Drop of ID table guards as they just pervent use under ACPI.
- Switch to device properties to allow ACPI usage.
* st_uvis25
- Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
- Drop legacy platform data as no one seems to be using it.
- Use the device property API instead of OF specific.
* ti-ads7950
- typo fix in error message.
* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
iio: accel: bma180: BMA254 support
iio: pressure: bmp280: Allow device to be enumerated from ACPI
iio: pressure: bmp280: Drop ACPI support
dt-bindings: iio: adc: convert sd modulator to json-schema
iio: buffer: rename 'read_first_n' callback to 'read'
iio: buffer-dmaengine: Report buffer length requirements
bindings: iio: pressure: Add documentation for dlh driver
dt-bindings: Add asc vendor
iio: pressure: Add driver for DLH pressure sensors
iio: buffer-dmaengine: Add module information
iio: accel: bma180: Use explicit member assignment
iio: accel: bma180: Basic regulator support
iio: accel: bma180: Add dev helper variable
iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
iio: imu: st_lsm6dsx: check if pull_up is located in primary page
iio: imu: st_lsm6dsx: check if master_enable is located in primary page
iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
iio: light: remove unneeded semicolon
...
Currently the read of temp using of_property_read_u32_index is reading
a u32 value into a unsigned long long. This relies on machine endianness
to work correctly, so fix this by reading a u32 value and setting temp
to this value.
Addresses-Coverity: ("Reliance on integer endianness")
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We added a sysfs ABI for getting/setting the type of a thermocouple. This
driver supports chips that support specific fixed thermocouple types; we
cannot set it, but still we can add this sysfs attribute in RO mode to
read-back the thermocouple type.
This driver supports actually several chips:
- max6675
- max31855[k/j/n/s/t/e/r]asa family
Max6675 supports only K-type thermocouples, so we can just report that.
Each chip in max31855 family supports just one specific thermocouple type
(in the obvious way: i.e. max31855jasa supports J-type). This driver did
accept a generic SPI ID and OF compatible "max31855" which does not give
any clue about which chip is really involved (and unfortunately it seems
we have no way to detect it).
This patch introduces a new set of, more specific, SPI IDs and OF
compatible strings to better match the chip type.
The old, generic, "max31855" binding is kept for compatibility reasons, but
this patch aims to deprecate it, so, should we hit it, a warning is spit.
In such case the reported thermocouple type in sysfs is '?', because we
have no way to know.
Regarding the implementation: the thermocouple type information is stored
in the driver private data and I've kept only two maxim_thermocouple_chip
types in order to avoid a lot of duplications (seven chip types with just
a different thermocouple type).
RFT because I have no real HW to test this.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sensor support various thermocouple types (e.g. J, K, N, ...). The
driver allows to configure this parameter using a DT property.
This is useful when i.e. the thermocouple is physically tied to the sensor
and it is usually not removed, or when it is at least known in advance
which sensor will be connected to the circuit.
However, if the user can randomly connect any kind of thermocouples (i.e.
the device exposes a connector, and the user is free to connect its own
sensors), it would be more appropriate to provide a mechanism to
dynamically switch from one thermocouple type to another. This can be i.e.
handled in userspace by a GUI, a configuration file or a program that
detects the thermocouple type by reading a GPIO, or a eeprom on the probe,
or whatever.
This patch adds a IIO attribute that can be used to override, at run-time,
the DT-provided setting (which serves as default).
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor can perform samples averaging in hardware, but currently the
driver leaves this setting alone (default is no averaging).
This patch binds this HW setting to the "oversampling_ratio" IIO attribute
and allows the user to set the averaging as desired (the HW supports
averaging of 2, 5, 8 or 16 samples; in-between values are rounded up).
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor has an embedded notch filter for reducing interferences caused
by the power mains. This filter can be tuned to reject either 50Hz or 60Hz
(and harmonics).
Currently the said setting is left alone (the sensor defaults to 60Hz).
This patch introduces a IIO attribute that allows the user to set the said
filter to the desired frequency.
NOTE: this has been intentionally not tied to any DT property to allow
the configuration of this setting from userspace, e.g. with a GUI or by
reading a configuration file, or maybe reading a GPIO tied to a physical
switch or accessing some device that can autodetect the line frequency.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Patrick Havelange <patrick.havelange@essensium.com>
Cc: Matt Weber <matthew.weber@rockwellcollins.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Chuhong Yuan <hslester96@gmail.com>
Cc: Daniel Gomez <dagmcr@gmail.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature
Measurement System. It measures a wide variety of temperature sensors and
digitally outputs the result, in °C or °F, with 0.1°C accuracy and
0.001°C resolution. It can measure the temperature of all standard
thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs,
thermistors and diodes.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adding missing indio_dev->dev.of_node references so that, in case multiple
max31856 are present, users can get some clues to being able to distinguish
each of them. While at it, add also the missing parent reference.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
The remove functions are redundant now and can
be deleted.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here are some small driver bugfixes for some staging/iio/counter
drivers.
Staging and IIO have been lumped together for a while, as those
subsystems cross the areas a log, and counter is used by IIO, so that's
why they are all in one pull request here.
These are small fixes for reported issues in some iio drivers, the erofs
filesystem, and a build issue for counter code.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyM7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymBUwCYn7LKiishfnvx8PpGF1lGHNmtYACgrNoAWKRZ
PUlOWXEbtD7NAPtqn3c=
=tXAQ
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO/counter fixes from Greg KH:
"Here are some small driver bugfixes for some staging/iio/counter
drivers.
Staging and IIO have been lumped together for a while, as those
subsystems cross the areas a log, and counter is used by IIO, so
that's why they are all in one pull request here.
These are small fixes for reported issues in some iio drivers, the
erofs filesystem, and a build issue for counter code.
All have been in linux-next with no reported issues"
* tag 'staging-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: erofs: add requirements field in superblock
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
-----BEGIN PGP SIGNATURE-----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=2i3G
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 5.2 cycle.
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
* tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
Based on 1 normalized pattern(s):
this file is subject to the terms and conditions of version 2 of the
gnu general public license see the file copying in the main
directory of this archive for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 55 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.108941081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
it and or modify it under the terms of the gnu general public
license version 2 as published by the free software foundation this
program is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 11 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.249870634@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register EE_VERSION contains mixture of calibration information and DSP
version. So far, because calibrations were definite, the driver
compatibility depended on whole contents, but in the newer production
process the calibration part changes. Because of that, value in EE_VERSION
will be changed and to avoid that calibration value is same as DSP version
the MSB in calibration part was fixed to 1.
That means existing calibrations (medical and consumer) will now have
hex values (bits 8 to 15) of 83 and 84 respectively. Driver compatibility
should be based only on DSP version part of the EE_VERSION (bits 0 to 7)
register.
Signed-off-by: Crt Mori <cmo@melexis.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/iio/temperature/maxim_thermocouple.ko | grep alias
alias: spi:max31855
alias: spi:max6675
After this patch:
modinfo drivers/iio/temperature/maxim_thermocouple.ko | grep alias
alias: spi:max31855
alias: spi:max6675
alias: of:N*T*Cmaxim,max31855C*
alias: of:N*T*Cmaxim,max31855
alias: of:N*T*Cmaxim,max6675C*
alias: of:N*T*Cmaxim,max6675
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently if mask is neither CHAN_INFO_RAW or CHAN_INFO_SCALE then
then an uninitialized error return 'ret' is returned. Fix this by
adding a default case that ensures -EINVAL is returned for this
specific case.
Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for Maxim MAX31856 thermocouple
temperature sensor support.
More information can be found in:
https://www.maximintegrated.com/en/ds/MAX31856.pdf
NOTE: Driver support only Comparator Mode.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan Cameron
Andy Shevchenko
Puranjay Mohan
Alexandru Ardelean
Greg Kroah-Hartman
Ye Xiang
Slaveyko Slaveykov
Nuno Sá
Crt Mori
Lee Jones
Lars-Peter Clausen
Alexandru Ardelean
Rohit Sarkar
Jeff LaBundy
Colin Ian King
Andrea Merello
Chuhong Yuan
Linus Torvalds
Thomas Gleixner
Daniel Gomez
Paresh Chaudhary