Bspec and the code suggests that the interrupt signaled by IIR[7,5]
(DISPLAY_PIPE_A/B_VBLANK) is a first level IRQ flag for the second
level PIPEA/BSTAT[2] (Start of Vertical Blank) interrupt. Measuring
the relative timings of when IIR[7] and PIPEASTAT[1,2] get set and
checking the effect of unmasking different pipestat and IIR events
shows that this isn't so:
First, ISR/IIR[7] gets set independently of PIPEASTAT[18] (Start of
Vertical Blank Enable) or any other pipestat enable bit, so it isn't
a first level IRQ bit showing the state of PIPEASTAT[2], but is
connected directly to the timing generator.
Second, setting only PIPEASTAT[18] and leaving all other pipestat events
disabled, IIR[6] (DISPLAY_PIPE_A_EVENT) gets set close to the moment when
PIPEASTAT[2] gets set, so the former is a first level interrupt flag for
the latter. The bspec is rather unclear about this, but I also assume
that IIR[6] signals all pipestat A events, except PIPEASTAT[31] (FIFO
Under-run Status).
Third, IIR[7] is set close to the moment when PIPEASTAT[1] (Framestart
Interrupt) gets set, in the mode I used about 12usec after PIPEASTAT[2]
and IIR[6] gets set. This means the IIR[7] isn't marking the start of
vblank, but rather signals the framestart event.
Based on the above, we don't need to unmask IIR[7] when waiting for
start of vblank events, but we can rely on IIR[6] being always unmasked,
which will signal when PIPEASTAT[2] gets set. Doing this will also get
rid of the overhead of getting an interrupt and servicing IIR[7], which
is atm raised always some time after IIR[6]/PIPEASTAT[2] is raised.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RFCv2: Reorganize array indexing so that full offsets can be used as
is. It makes grepping for registers in i915_reg.h much easier. Also
move offset arrays to intel_device_info.
v1: Fixed offsets for VLV, proper eDP handling
v2: Fixed BCLRPAT, PIPESRC, PIPECONF and DSP* macros.
v3: Added EDP pipe comment, removed redundant offset arrays for
MSA_MISC and DDI_FUNC_CTL.
v4: Rename patch and report object size increase.
v5: Change location of commas, add PIPE_EDP into enum pipe
v6: Insert PIPE_EDP_OFFSET into pipe offset array
v7: Set I915_MAX_PIPES back to 3, change more registers accessors
to use the new macros, get rid of _PIPE_INC and add dev_priv
as a parameter where required by the new macros.
Upcoming hardware will not have the various display pipe register
ranges evenly spaced in memory. Change register address calculations
into array lookups.
Tested on SNB, VLV, IVB, Gen2 and HSW w/eDP.
I left the UMS cruft untouched.
Size differences:
text data bss dec hex filename
596431 4634 56 601121 92c21 i915.ko (new)
593199 4634 56 597889 91f81 i915.ko (old)
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since a purged buffer is one without any associated pages, attempting to
use it should generate EFAULT rather than EINVAL, as it is not strictly
an invalid parameter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
EFAULT will be a possible return code where backing storage is
transient, such after it is purged by madvise. As such it is to be
expected and so should not trigger a WARN inside i915_gem_fault() but be
converted silently to SIGBUS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we enter RC6 and GFX Clocks are off, the voltage remains higher
than Vmin. When we try to set the freq to RPn, it might fail since the
Gfx clocks are down. So to fix this in Gfx idle, Bring the GFX clock up
and set the freq to RPn then move GFx down.
v2: remove vlv_update_rps_cur_delay function. Update commit message (Daniel)
v3: Fix the timeout during wait for gfx clock (Jesse)
v4: addressed comments on set freq and punit wait (Ville)
v5: use wait_for while waiting for GFX clk to be up. (Daniel)
update cur_delay before requesting min_delay. (Ville)
v6: use wait_for while waiting for punit. (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we seek the guilty batch using request and hangcheck
score, this code is not needed anymore.
v2: Rebase. Passing dev_priv instead of getting it from last_ring
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With full ppgtt using acthd is not enough to find guilty
batch buffer. We get multiple false positives as acthd is
per vm.
Instead of scanning which vm was running on a ring,
to find corressponding context, use a different, simpler,
strategy of finding batches that caused gpu hang:
If hangcheck has declared ring to be hung, find first non complete
request on that ring and claim it was guilty.
v2: Rebase
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73652
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both Bspec and the W/A database state that WaDisablePSDDualDispatchEnable
is only needed for IVB GT1.
The only real confusion here is that the the W/A database also says to
write to the GT2 only register as well, which is strange if the W/A is
only for GT1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IVB GT2 has two registers for these things, and both must be written.
To add a bit more confusion both Bspec and the W/A database state that
WaDisablePSDDualDispatchEnable is only needed for IVB GT1, but the W/A
database also says to write even the second GT2 only register. So I
don't really know what the right thing here is.
Note that Bspec disagrees with the w/a database here, but Ville
confirmed (by asking Chris) that on gt1 the 2nd reg doesn't exist.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add note as requested by Rodrigo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to use the GTT for reading back objects upon an error so that we
have exactly the information that the GPU saw. However, it is verboten
to access snoopable pages through the GTT and causes my PineView GPU to
throw a page fault instead.
This has not been a problem in the past as we only dumped ringbuffers
and batchbuffers, both of which must be not snooped. However, the
introduction of HWS page dumping leads to a read of a snooped object
through the GTT. This was introduced by
commit f3ce382139
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Jan 23 22:40:36 2014 +0000
drm/i915: Include HW status page in error capture
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet:s/uncached/not snooped/ for one case in the commit message as
requested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Repeating the same information multiple times is just annoying.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we have stopped rings then we know that test is running
so no need for spam. In addition, only spam when default
context gets banned.
v2: - make sure default context ban gets shown (Chris)
- use helper for checking for default context, everywhere (Chris)
v3: - dont be quiet when debug is set (Ben, Daniel)
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=73652
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With full ppgtt support drm_i915_file_private gained knowledge
about the default context. Also reset stats are now inside
i915_hw_context so we can use proper abstraction.
v2: Move BUG_ON and WARN_ON to more proper locations (Ben)
v3: Pass dev directly to i915_context_is_banned to avoid the need to
dereference ctx->last_ring. Spotted by Mika when checking my
s/BUG/WARN/ change, I've missed this ->last_ring dereference.
Suggested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com> (v2)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v2)
[danvet: s/BUG/WARN/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The optimization helps IVB too. No piglit regression.
Signed-off-by: Chia-I Wu <olv@lunarg.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The optimization is available on Ivy Bridge and later, and is disabled by
default. Enabling it helps certain workloads such as GLBenchmark TRex test.
No piglit regression.
v2
- no need to save the register before suspend as init_clock_gating can
correctly program it after resume
- split IVB change to another commit
Signed-off-by: Chia-I Wu <olv@lunarg.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebased upon cleaned up error state
v3: Make sure hangcheck info remains last (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris:
Do we also want to capture?
GAC_ECO_BITS /* gen6,7 */
GAM_ECOCHK /* gen6,7 */
GAB_CTL /* gen6 */
GFX_MODE /* gen6 */
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Moved num_requests up (Chris)
Rebased on new hws page capture which required a rename since it made
two members named, 'hws' in the per ring error state. (Ben)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This helps make an upcoming patch a bit more reviewable
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create logical sections in an attempt to clean up, and continue to keep
future additions clean.
v2: Reworded the comments. Added section headers (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code has become quite hairy. By relocating all the generic registers
it will become more obvious where future ones should go. There is still
admittedly a bit of confusion left for things like per ring registers.
A subsequent patch will clean this function up.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next - I need to backmerge drm-intel-fixes patches
touching the error capture code to be able to merge Ben's cleanup
patches.
Conflicts:
drivers/gpu/drm/i915/i915_gpu_error.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
more fixes for nouveau.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: resume display if any later suspend bits fail
drm/nouveau: fix lock unbalance in nouveau_crtc_page_flip
drm/nouveau: implement hooks for needed for drm vblank timestamping support
drm/nouveau/disp: add a method to fetch info needed by drm vblank timestamping
drm/nv50: fill in crtc mode struct members from crtc_mode_fixup
more radeon fixes
* 'drm-next-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dce8: workaround for atom BlankCrtc table
drm/radeon/DCE4+: clear bios scratch dpms bit (v2)
drm/radeon: set si_notify_smc_display_change properly
drm/radeon: fix DAC interrupt handling on DCE5+
drm/radeon: clean up active vram sizing
drm/radeon: skip async dma init on r6xx
drm/radeon/runpm: don't runtime suspend non-PX cards
drm/radeon: add ring to fence trace functions
drm/radeon: add missing trace point
drm/radeon: fix VMID use tracking
If either idling channels or suspending the fence were to fail, the
display would never be resumed. Also if a client fails, resume the fence
(not functionally important, but it would potentially leak memory).
See https://bugs.freedesktop.org/show_bug.cgi?id=70213
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes a regression introduced by d5c1e84b3a
"drm/nouveau: hold mutex while syncing to kernel channel".
Cc: stable@vger.kernel.org #3.13
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DRM uses the adjusted mode to calculate constants for vblank
timestamping. Our encoder mode_fixup (usually) replaces this data
with our backend mode information, which doesn't have the needed
data filled in already.
Reported-by: Mario Kleiner mario.kleiner.de@gmail.com
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Request by Ben Widawsky in his review of a patch touching this code.
v2: Clarify the disdinction between evicting vmas (to free up virtual
address space) and evicting objects (to free up actual system memory).
Suggested by Ben.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some DCE8 boards have a funky BlankCrtc table that results
in a timeout when trying to blank the display. The
timeout is harmless (all operations needed from the table
are complete), but wastes time and is confusing to users so
work around it.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=73420
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This is effectively a revert of 4573388c92.
Forcing a display active when there is none causes problems with
dpm on some SI boards which results in improperly initialized
dpm state and boot failures on some boards. As for the bug commit
4573388c92 tried to address, one can manually force the state to
high for better performance when using the card as a headless compute
node until a better fix is developed.
bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=73788https://bugs.freedesktop.org/show_bug.cgi?id=69395
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
cc: stable@vger.kernel.org
During eviction, we are only considering how to free up space within the
current address space and not concerned with freeing up physical memory.
As such we need only skip nodes that pinned in the current VM and not
globally.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DCE5 and newer hardware only has 1 DAC. Use the correct
offset. This may fix display problems on certain board
configurations.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
If we are not able to properly initialize one of the gpu
engines for buffer paging, we limit vram to the size of
the cpu visible aperture. We generally either use the gfx
or dma engine to do this. Clean up the size limiting code
to only adjust the size based on what ring is selected
for buffer paging rather than making assumptions about which
engine is selected for paging.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The hw is buggy and it's not currently used, but it's
currently still initialized by the driver. Skip the init.
Skipping init also seems to improve stability with dpm on
some r6xx asics.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Prevent runtime suspend of non-PX GPUs. Runtime suspend is
not what we want in those cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Otherwise we allocate a new VMID on nearly every submit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The initial jiffies value can be non-0, so set the inital panel power
sequencer timestamps accordingly. This didn't cause a problem on 64 bit
machines but on 32 bit jiffies is initially -300*HZ, so if the panel
power is initally off in the call from edp_panel_vdd_on()->
wait_panel_power_cycle() we'd wait up to ~300 sec more than needed.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
schedule_timeout_uninterruptible() takes jiffies not ms.
v2:
- ignore the overflow issue, the practical part of that should
be solved instead in the caller (Chris)
Note that this issue was introduced in
commit dce56b3c62
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Dec 19 14:29:40 2013 -0200
drm/i915: save some time when waiting the eDP timings
I've accidentally merged the broken v4 version of the patch (where
Jani noticed the issue [1]) instead of the v5, which was fixed [2].
[1] http://mid.gmane.org/87fvpnkgyg.fsf@intel.com
[2] http://mid.gmane.org/1388778311-2020-1-git-send-email-przanoni@gmail.com
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add admission of incompetence in the form of a note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When current delay is already at max delay, Let's disable the PM UP
THRESHOLD INTRRUPTS, so that we will not get further interrupts until
current delay is less than max delay, Also request for the PM DOWN
THRESHOLD INTRRUPTS to indicate the decrease in clock freq. and
viceversa for PM DOWN THRESHOLD INTRRUPTS.
v2: Use bool variables (Daniel)
v3: Fix Interrupt masking bit (Deepak)
v4: Use existing symbolic constants in i915_reg.h (Daniel)
v5: Add pm interrupt mask after new_delay calculation (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
[danvet: Pass new_delay by value as suggested by Ville. Also appease
checkpatch.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're disabling a boatload of clock gating features on VLV. Maybe these
days we don't need to do that. At least I'm not aware of any workarounds
with this level of paranoia.
This reverts commit 4e8c84a5b1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaDisable4x2SubspanOptimization isn't listed for VLV in the workaround
database, but BSpec says that the relevant bit must be set. Add a
comment to remind people of this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Call gen7_setup_fixed_func_scheduler() on VLV as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec states that the thread override values set by
gen7_setup_fixed_func_scheduler() are invalid for HSW. So let's not
muck around with them.
Since gen7_setup_fixed_func_scheduler() now has two totally independent
parts, one for IVB and one for HSW, move the HSW part directly into
haswell_init_clock_gating().
Note tht there's another workaround by the name of
WaHSWVSRefCountFullforceMissDisable which basically claims that later
steppings don't need the fix, but since WaVSRefCountFullforceMissDisable
is listed to be needed for all steppings play it safe and keep applying
the workaround.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak
Antti Koskipaa
Chris Wilson
Mika Kuoppala
Deepak S
Ville Syrjälä
Chia-I Wu
Ben Widawsky
Daniel Vetter
Dave Airlie
Ilia Mirkin
Maarten Lankhorst
Ben Skeggs
Alex Deucher
Christian König