Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting Config[OD] gets rid of a _LOT_ of spurious CPLD interrupts,
but also decreases overall performance a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2347/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus
area. Currently, addresses at the far end of the 32bit area are assumed
to belong to the PCMCIA area and fixed up to the real 36bit address before
being passed to ioremap().
A previous commit enabled 64 bit physical size for the resource datatype on
Alchemy and this allows to use the correct 36bit addresses when registering
the PCMCIA sockets.
This patch removes the 32-to-36bit address fixup and registers the Alchemy
demo board pcmcia socket with the correct 36bit physical addresses.
Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet
card.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/994/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement reset / poweroff in the board code instead. The peripheral reset
code is gone too since YAMON which all in-tree boards use does the same
work when it boots.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/783/
Patchwork: http://patchwork.linux-mips.org/patch/882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
loops_per_jiffy depends on coreclk speed; preset it instead of
letting the kernel waste precious microseconds trying to approximate it.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/cputable.c
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle
Manuel Lauss
Manuel Lauss