Граф коммитов

155 Коммитов

Автор SHA1 Сообщение Дата
Johannes Berg e1a0c6b3a4 mac80211: stop toggling IEEE80211_HT_CAP_SUP_WIDTH_20_40
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.

To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.

If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.

Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.

While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-15 09:41:30 +01:00
Johannes Berg fd0f979a1b mac80211: simplify idle handling
Now that we have channel contexts, idle is (pretty
much) equivalent to not having a channel context.
Change the code to use this relation so that there
no longer is a need for a lot of idle recalculate
calls everywhere.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-11 18:45:01 +01:00
Johannes Berg 8cef2c9df8 cfg80211: move TSF into IEs
While technically the TSF isn't an IE, it can be
necessary to distinguish between the TSF from a
beacon and a probe response, in particular in
order to know the next DTIM TBTT, as not all APs
are spec compliant wrt. TSF==0 being a DTIM TBTT
and thus the DTIM count needs to be taken into
account as well.

To allow this, move the TSF into the IE struct
so it can be known whence it came.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-11 18:44:59 +01:00
Johannes Berg 5b112d3d09 cfg80211: pass wiphy to cfg80211_ref_bss/put_bss
This prepares for using the spinlock instead of krefs
which is needed in the next patch to track the refs
of combined BSSes correctly.

Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-11 18:44:52 +01:00
Johannes Berg 1672c0e319 mac80211: start auth/assoc timeout on frame status
When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.

For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31 14:28:43 +01:00
Johannes Berg d6a8322882 mac80211: track enable_beacon explicitly
Instead of calculating in ieee80211_bss_info_change_notify()
whether beaconing should be enabled or not, set it in the
correct places in the callers. This simplifies the logic in
this function at the expense of offchannel, but is also more
robust.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-03 13:01:35 +01:00
Emmanuel Grumbach d45c41722a mac82011: use frame control to differentiate probe resp/beacon
The probe response/beacon management frame RX code passes a
bool parameter to differentiate beacons and probe responses.
This is useless since we have the frame and can thus use its
frame control field. Moreover it is buggy since there is one
call to ieee80211_rx_bss_info with a beacon frame that is
indicated as a probe response, which is also fixed by using
the frame control field, so do that.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-03 13:01:33 +01:00
Johannes Berg b998e8bb3e mac80211: remove final sta_info_flush()
When all interfaces have been removed, there can't
be any stations left over, so there's no need to
flush again. Remove this, and all code associated
with it, which also simplifies the function.

Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-03 13:01:16 +01:00
Stanislaw Gruszka 34bcf71502 mac80211: fix ibss scanning
Do not scan on no-IBSS and disabled channels in IBSS mode. Doing this
can trigger Microcode errors on iwlwifi and iwlegacy drivers.

Also rename ieee80211_request_internal_scan() function since it is only
used in IBSS mode and simplify calling it from ieee80211_sta_find_ibss().

This patch should address:
https://bugzilla.redhat.com/show_bug.cgi?id=883414
https://bugzilla.kernel.org/show_bug.cgi?id=49411

Reported-by: Jesse Kahtava <jesse_kahtava@f-m.fm>
Reported-by: Mikko Rapeli  <mikko.rapeli@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-03 12:59:57 +01:00
John W. Linville c66cfd5325 Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next 2012-12-11 16:04:03 -05:00
Simon Wunderlich 2f91a96799 mac80211: adapt slot time in IBSS mode
In 5GHz/802.11a, we are allowed to use short slot times. Doing this
may increases performance by 20% for legacy connections (54 MBit/s).
I can confirm this in my tests (27% more throughput using iperf), and
also have a small positive effect (5% more throughput) for HT rates,
tested on 1 stream.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-12-04 15:54:43 +01:00
John W. Linville 62c8003ecb Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2012-11-26 14:46:41 -05:00
Johannes Berg 4bf88530be mac80211: convert to channel definition struct
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:59 +01:00
Johannes Berg 3d9d1d6656 nl80211/cfg80211: support VHT channel configuration
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.

Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)

This also adds new helper functions:
 - cfg80211_chandef_create to create a channel def
   struct given the control channel and channel type,
 - cfg80211_chandef_identical to check if two channel
   definitions are identical
 - cfg80211_chandef_compatible to check if the given
   channel definitions are compatible, and return the
   wider of the two

This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
 - regulatory checks on the usable bandwidth (if that
   even makes sense)
 - regulatory TX power (database can't deal with it)
 - a proper channel compatibility calculation for the
   new channel types

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:59 +01:00
Johannes Berg 683b6d3b31 cfg80211: pass a channel definition struct
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:58 +01:00
Antonio Quartulli 7bed20503f mac80211: in ADHOC print debug message for every Auth message
The debug message has to be printed also for an Auth message with
auth_sequence != 1. This helps understanding whether the two Auth
messages are exchanged correctly or not.

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 11:32:42 +01:00
John W. Linville 75c8ec71fb Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2012-11-21 14:43:51 -05:00
John W. Linville b311749477 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c
	drivers/net/wireless/iwlwifi/pcie/tx.c
2012-11-21 12:57:56 -05:00
Thomas Pedersen f4bda337bb mac80211: support RX_FLAG_MACTIME_END
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-13 21:43:55 +01:00
Simon Wunderlich b78a4932f5 mac80211: deinitialize ibss-internals after emptiness check
The check whether the IBSS is active and can be removed should be
performed before deinitializing the fields used for the check/search.
Otherwise, the configured BSS will not be found and removed properly.

To make it more clear for the future, rename sdata->u.ibss to the
local pointer ifibss which is used within the checks.

This behaviour was introduced by
f3209bea11
("mac80211: fix IBSS teardown race")

Cc: stable@vger.kernel.org
Cc: Ignacy Gawedzki <i@lri.fr>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-13 21:35:07 +01:00
John W. Linville ab3d59d265 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/mwifiex/cfg80211.c
2012-10-29 16:05:51 -04:00
Antonio Quartulli badecb001a mac80211: fix SSID copy on IBSS JOIN
The 'ssid' field of the cfg80211_ibss_params is a u8 pointer and
its length is likely to be less than IEEE80211_MAX_SSID_LEN most
of the time.

This patch fixes the ssid copy in ieee80211_ibss_join() by using
the SSID length to prevent it from reading beyond the string.

Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[rewrapped commit message, small rewording]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-26 22:52:18 +02:00
Sujith Manoharan c13a765bd9 mac80211: Notify new IBSS network creation
Initialization of beacon transmission in IBSS mode depends
on whether a new BSS is being created or joined. When joining
an existing IBSS network, beaconing has to start only after
a TSF-sync has happened - this is explained in 11.1.4.

Introduce a new parameter in the BSS information structure to
indicate creator/joiner mode.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18 09:01:53 +02:00
Jouni Malinen 700e8ea677 mac80211: Take status code as parameter to ieee80211_send_auth
Non-zero status code may be needed for Authentication frames, e.g.,
when using SAE.

Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17 11:02:10 +02:00
Johannes Berg 04ecd2578e mac80211: track needed RX chains for channel contexts
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).

Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17 11:02:09 +02:00
Johannes Berg 55de908ab2 mac80211: use channel contexts
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.

This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.

Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.

Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.

[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-17 11:02:09 +02:00
Sylvain Roger Rieunier 2514ec8653 mac80211: fix IBSS auth TX debug message
In the IBSS auth TX debug message the BSSID and DA
address are reversed, fix that.

Signed-off-by: Sylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message and make it fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-09-20 10:31:34 +02:00
Antonio Quartulli 2cc59e784b mac80211: reply to AUTH with DEAUTH if sta allocation fails in IBSS
Whenever a host gets an AUTH frame it first allocates a new
station and then replies with another AUTH frame. However,
if sta allocations fails the host should send a DEAUTH frame
instead to tell the other end that something went wrong.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-09-07 13:50:47 +02:00
Antonio Quartulli e687f61eed mac80211: add supported rates change notification in IBSS
In IBSS it is possible that the supported rates set for a station changes over
time (e.g. it gets first initialised as an empty set because of no available
information about rates and updated later). In this case the driver has to be
notified about the change in order to update its internal table accordingly (if
needed).

This behaviour is needed by all those drivers that handle rc internally but
leave stations management to mac80211

Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[Johannes - add docs, validate IBSS mode only, fix compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-08-20 13:31:43 +02:00
Johannes Berg e83e6541ce mac80211: use eth_broadcast_addr
Instead of memset().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-31 16:19:51 +02:00
Johannes Berg 273686d664 mac80211: use oper_channel in ibss
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.

Use oper_channel instead.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-07-31 16:18:52 +02:00
Johannes Berg bdcbd8e0e3 mac80211: clean up debugging
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
 * a lot of messages should be pr_info, not pr_debug
 * wholesale use of pr_debug makes it require *both*
   Kconfig and dynamic configuration
 * there are still a lot of ifdefs
 * the style is very inconsistent, sometimes the
   sdata->name is printed in front

Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-24 11:32:29 +02:00
Johannes Berg 08ce5abe3d mac80211: two small verbose debug cleanups
Two instances of CONFIG_MAC80211_VERBOSE_DEBUG
should be different, fix them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-22 12:53:05 +02:00
Will Hawkins 452a6d2261 mac80211: send auth in IBSS only if userspace isn't handling it
Check the auth frame registration count before sending
"open system" authentication messages when a new station
registers on a particular IBSS network. This stops us
from sending out multiple authentication messages with
different authentication algorithms.

Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-20 20:03:42 +02:00
Johannes Berg d58e7e37aa cfg80211: simplify cfg80211_can_beacon_sec_chan API
Change cfg80211_can_beacon_sec_chan() to return true
if there is no secondary channel to simplify all the
current users of it. They all check the channel type
before calling the function because it returns false
if there's no secondary channel.

Also actually document the return value.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:32:16 -04:00
Joe Perches 499f42bb03 net: mac80211: Add and use ibss_vdbg debugging macro
Simplify the use of #ifdef CONFIG_MAC80211_IBSS_DEBUG/#endif
by adding a logging macro to encapsulate the test.

Convert the appropriate uses too.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:32:10 -04:00
Joe Perches f0d232080f net: mac80211: Convert printk(KERN_DEBUG to pr_debug
Standardize the debugging to be able to use dynamic_debug.

Coalesce formats, align arguments.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-05 15:27:16 -04:00
John W. Linville a0d0d1685f Merge git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next 2012-05-22 15:18:06 -04:00
Ashok Nagarajan 0d894ec501 mac80211: Push the deleted comment to correct place
This comment is deleted in the patch "mac80211: Advertise HT protection mode in
IEs". Moving the comment to the now corrected place.

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-16 13:24:24 -04:00
Joe Perches e87cc4728f net: Convert net_ratelimit uses to net_<level>_ratelimited
Standardize the net core ratelimited logging functions.

Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-15 13:45:03 -04:00
David S. Miller c597f6653d Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next 2012-05-14 18:00:48 -04:00
Joe Perches b203ca3912 mac80211: Convert compare_ether_addr to ether_addr_equal
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-09 20:49:18 -04:00
Ashok Nagarajan 431e315423 mac80211: Advertise HT protection mode in IEs
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-05-08 21:53:57 -04:00
David S. Miller f24001941c Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")

The former moved around the sysctl register/unregister calls, the
later simply removed them.

With help from Stephen Rothwell.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-23 23:15:17 -04:00
Felix Fietkau 6741e7f048 mac80211: fix logic error in ibss channel type check
The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.

HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17 14:17:04 -04:00
Ashok Nagarajan 9ebb61a23d mac80211: Modify sta_get_rates to give basic rates
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-11 16:23:47 -04:00
Johannes Berg 32c5057b22 mac80211: use IEEE80211_NUM_ACS
When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-10 14:56:10 -04:00
Johannes Berg 074d46d1d2 wireless: rename ht_info to ht_operation
Since some of the HT code pre-dates 802.11n-2009
some names are wrong. The one that bothers me most
is that "HT operation" is called "HT information"
in our code and that causes confusion.

Rename "HT information" to "HT operation" and also
the control_chan field to primary_chan to match
the name used in the spec.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-09 16:05:55 -04:00
Felix Fietkau 888d04dfbe mac80211: use compare_ether_addr on MAC addresses instead of memcmp
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:38:31 -05:00
Johannes Berg d26ad3771f mac80211: clean up asm/unaligned.h inclusion
Some files implicitly get this via mesh.h
which itself doesn't need it, so move the
inclusion into the right files. Some other
files don't need it at all but include it,
so remove it from there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:32 -05:00