7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)
After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16c6 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
[ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O
4.2.0-rc2+ #8
[ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[ 908.984181] Call Trace:
[ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[ 908.984225] [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[ 908.984228] [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[ 908.984244] [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[ 908.984247] ---[ end trace 7c006ed4abbef24b ]---
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f939981492 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd ("bonding: Manage /proc/net/bonding/ entries from
the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, dma_sync_single_for_cpu() shouldn't have been called in the first place
(it's a streaming DMA API), dma_unmap_single() should have been called instead.
Second, dma_unmap_single() call after handing the buffer to napi_gro_receive()
makes little sense. Moreover desc->dptr might not be valid at this point.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All structures used in traffic forwarding are rcu-protected:
ipvl_addr, ipvl_dev and ipvl_port. Thus we can unhash addresses
without synchronization. We'll anyway hash it back into the same
bucket: in worst case lockless lookup will scan hash once again.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing kfree_rcu(addr, rcu);
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are unused after commit f631c44bbe ("ipvlan: Always set broadcast bit in
multicast filter").
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVpgZgAAoJEP5prqPJtc/HPsMIAJTtkEzuZvjjV0rJ3/qvicdi
hz8Up9T4A3Ef8ynXlejYUTL6yksuo/rOwGwzcqF9QrJPaihqSwxLtPHbshKWp1RB
VX6Vjli7vDzHdX2wDjICt4If9FDCtJXLHfk6WLNwMnOX+ODfiGdyCR5L89c1asnZ
zDEI0HlyZO6yRHYyQF31fm/ze6oHOPjL49pypzRf6LwRJVRs6rdUUIZza3DadHRU
S1Lez1kXtBEVx4F6yryziLdvrM/7nfR0dfnW1Q0l3jtcjijfLeRN6ky4vEarw16s
onymQ8zXB0U0DK0waXhi0dL46p28KNlHtz79fgugHj2IGVcgQhwjsbO4EAsQbiE=
=S0cQ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.2-20150715' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-15
this is a pull request of 12 patches by me.
This series fixes the use of the skb after netif_receive_skb() / netif_rx()
which exists in several drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6c3e921b18.
commit 6c3e921b18 ("net: fec: Ensure clocks are enabled while using mdio
bus") prevents the kernel to boot on mx6 boards, so let's revert it.
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The > should be >=. I also added spaces around the '-' operations so
the code is a little more consistent and matches the condition better.
Fixes: f53c3fe8da ('xen-netback: Introduce TX grant mapping')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Missing list head init in bluetooth hidp session creation, from Tedd
Ho-Jeong An.
2) Don't leak SKB in bridge netfilter error paths, from Florian
Westphal.
3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
Grall.
4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
Baechle.
5) Fix race between rhashtable resize events and table walks, from Phil
Sutter.
6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
Daniel Borkmann.
7) Missing security layer socket state initialization in tipc code,
from Stephen Smalley.
8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
Denys Vlasenko.
9) Missing minor_idr destroy on module unload on macvtap driver, from
Johannes Thumshirn.
10) Various pktgen kernel thread races, from Oleg Nesterov.
11) Fix races that can cause packets to be processed in the backlog even
after a device attached to that SKB has been fully unregistered.
From Julian Anastasov.
12) bcmgenet driver doesn't account packet drops vs. errors properly,
fix from Petri Gynther.
13) Array index validation and off by one fix in DSA layer from Florian
Fainelli
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
can: replace timestamp as unique skb attribute
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
can: c_can: Fix default pinmux glitch at init
can: rcar_can: unify error messages
can: rcar_can: print request_irq() error code
can: rcar_can: fix typo in error message
can: rcar_can: print signed IRQ #
can: rcar_can: fix IRQ check
net: dsa: Fix off-by-one in switch address parsing
net: dsa: Test array index before use
net: switchdev: don't abort unsupported operations
net: bcmgenet: fix accounting of packet drops vs errors
cdc_ncm: update specs URL
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
bridge: mdb: allow the user to delete mdb entry if there's a querier
net: call rcu_read_lock early in process_backlog
net: do not process device backlog during unregistration
bridge: fix potential crash in __netdev_pick_tx()
net: axienet: Fix devm_ioremap_resource return value check
...
Commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245eb "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous change 3973c526ae (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
All the error messages in the driver but the ones from devm_clk_get() failures
use similar format. Make those two messages consitent with others.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Also print the error code when the request_irq() call fails in rcar_can_open(),
rewording the error message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix typo in the first error message printed by rcar_can_open().
Based on the original patch by Vladimir Barinov.
Fixes: 862e2b6af9 ("can: rcar_can: support all input clocks")
Reported-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of type *int*, so the "%d" format needs to be used instead.
While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:
error requesting interrupt fffffffa
because rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.
Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
bcmgenet driver needs to separate packet drops from packet errors.
When the driver has to drop a *good* packet, due to lack of buffers or
replacement skbs, increment only dev->stats.[rx|tx]_dropped.
When the driver encounters a bad Rx packet or Tx error, increment only
dev->stats.[rx|tx]_errors + relevant detailed error counter.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update referenced specs link to reflect actual file version and location.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix a spelling typo found in API-z8530-sync-txdma-open.html.
It is because this file was generated from comment in source,
I have to fix comment in source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 46aa27df88 ("net: axienet: Use devm_* calls")
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCM specs are not actually mandating a specific position in the frame for
the NDP (Network Datagram Pointer). However, some Huawei devices will
ignore our aggregates if it is not placed after the datagrams it points
to. Add support for doing just this, in a per-device configurable way.
While at it, update NCM subdrivers, disabling this functionality in all of
them, except in huawei_cdc_ncm where it is enabled instead.
We aren't making any distinction between different Huawei NCM devices,
based on what the vendor driver does. Standard NCM devices are left
unaffected: if they are compliant, they should be always usable, still
stay on the safe side.
This change has been tested and working with a Huawei E3131 device (which
works regardless of NDP position), a Huawei E3531 (also working both
ways) and an E3372 (which mandates NDP to be after indexed datagrams).
V1->V2:
- corrected wrong NDP acronym definition
- fixed possible NULL pointer dereference
- patch cleanup
V2->V3:
- Properly account for the NDP size when writing new packets to SKB
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 'c03abd84634d ("net: ethernet: cpsw: don't requests
IRQs we don't use")', common isr is split into tx and rx, but
in rx isr tx interrupt is also disabledi in cpsw_disable_irq().
So tx interrupts are not handled during rx interrupts and rx
napi completion and results in poor tx performance by 40Mbps.
Fixing by disabling only rx interrupt in rx isr.
Cc: Felipe Balbi <balbi@ti.com>
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr().
Here, this change is setting addr_assign_type to NET_ADDR_RANDOM.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@
identifier a,b;
@@
-random_ether_addr(a->b);
+eth_hw_addr_random(a);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limit for BQL is updated each time we call
netdev_tx_completed_queue.
Without this patch the BQL limit was updated for every TX event we
see.
The issue was that this only updated the limit to handle the data
we complete in two events as the first event wouldn't show that
enough traffic had been processed between them.
This was OK when interrupt moderation was off but not when it was
on as more data had to be completed in a single interrupt.
The patch changes this so that we do report the completion to BQL
only when all the TX events in the interrupt have been processed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is sold as 'NVIDIA Tegra USB 3.0 Ethernet'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: Zheng Liu <zhliu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As its first order of business, boomerang_interrupt() checks whether
the device really has any pending interrupts. If it does not,
it does nothing and returns, but it still returns IRQ_HANDLED.
This is wrong: interrupt was not handled, IRQ handlers of other
devices sharing this IRQ line need to be called.
vortex_interrupt() has it right: it returns IRQ_NONE in this case
via IRQ_RETVAL(0).
Do the same in boomerang_interrupt().
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3's current napi path is built to count every rx descriptor we recieve,
and use that as a count of the napi budget. That means its possible to return
from a napi poll halfway through recieving a fragmented packet accross multiple
dma descriptors. If that happens, the next napi poll will start with the
descriptor ring in an improper state (e.g. the first descriptor we look at may
have the end-of-packet bit set), which will cause a BUG halt in the driver.
Fix the issue by only counting whole received packets in the napi poll and
returning that value, rather than the descriptor count.
Tested by the reporter and myself, successfully
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids the double up_write to filter_sem if
efx_net_open() fails.
Resolves: 2d432f20d2
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some versions of MCFW do not support the MC_CMD_VADAPTOR_SET_MAC
command, and ENOSYS will be returned.
If the PF created its own vport, the function's datapath must be
stopped and the vport can be reconfigured to reflect the new MAC
address.
If the MCFW created the vport for the PF (which is the case when
the nic_data->vport_mac is blank), nothing further needs to be
done as the vport is not under the control of the PF.
This only applies to PFs because the MCFW in question does not
support VFs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli
Nikolay Aleksandrov
Vivien Didelot
Michael S. Tsirkin
Sergei Shtylyov
Konstantin Khlebnikov
WANG Cong
David S. Miller
Fabio Estevam
Marc Kleine-Budde
Dan Carpenter
Linus Torvalds
Oliver Hartkopp
J.D. Schroeder
Petri Gynther
Enrico Mioso
Masanari Iida
Krzysztof Kozlowski
Mugunthan V N
Vaishali Thakkar
Johannes Thumshirn
Peter Dunning
Zheng Liu
Denys Vlasenko
Neil Horman
Shradha Shah
Daniel Pieczko