When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not try to return a fragment entry from TC list. Otherwise we may not
clean properly allocated entries.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queues >= 4 we use different registers but we were not subtracting
the offset of 4. Fix this.
Found out by Coverity.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixup the XGMAC selftests by correctly finishing the implementation of
set_filter callback.
Result:
$ ethtool -t enp4s0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters -95
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdSWJ0AAoJEG4XJFUm622bwb4H/1cbH/VoPkNPfRb6783G3Fuc
SWcI655nMDHY3cElhLPGQrR4OuNYbFpBDT7O73XMIVqnkHlgq3L/VZD2qaacSd4H
tY4HEkkHobil9gdsEt8hpBstp9xNi36klDiq9gEOLT88eatdukCZTsCnBwaTFSEQ
84QxsVsHWuB+khVDay6jprA+vwL6YopOlPwfY9+q0LHWCHq1C98ZqPZoxjb8dzN7
bbW4hWIhMHRtN9ixPwvoRhscev2ZgRPHAncoGFE8bmRM79srZpG0mDeAhQPLGrJz
YSoGtylHpQxg3vzz2y80fMpH6jsUHFeA56xuKPQ5gnUm4bPeFbhx7h29DuABsAw=
=GDUP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-08-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.3
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
be_process_mcc() is invoked in 3 different places and
always with BHs disabled except the be_poll function
but since it's invoked from softirq with BHs
disabled it won't hurt.
v1->v2: added explanation to the patch
v2->v3: add a missing call from be_cmds.c
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to 'kfree_skb()' is missing in the error handling path of
'init_one()'.
This is already present in 'remove_one()' but is missing here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sun4i-emac uses the "phy" property to find the PHY it's supposed to
use. This property was deprecated in favor of "phy-handle" in commit
8c5b094476 ("dt-bindings: net: sun4i-emac: Convert the binding to a
schemas").
Add support for this new property name, and fall back to the old one in
case the device tree hasn't been updated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl1EJXQTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIHxvB/4jwFTPPBzCFxajnV2A38xantSrzz1X
p1t0JjWHUh1arN0d8P39CGwHCUKtA65uJQbrUmJO38Mon+/I8PnYksziWapC+x+A
GzucFoXwKj0SjzGnKfiM9OF5L2UZQnt2duT2DOiA4qqd0ROLPu9e3Es/++cYheHv
oRq9HQNnvHIekKiJJmZhdOwRHZB7/9W+NOecYwYZl8IDGQeguLTCFTrA/FSSmuDE
9xzZtpN5xz7ohSwp1IdKvA6gSgV42iHuRBoH4RAqIC7qCguQge1iLhqHP4DcZkik
f1C9EbQcK8J0S7n816rSEUu8vFj4tXsMA4a1EN7J0zz45eb1nL6NERbS
=JPX0
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.3-20190802' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-08-02
this is a pull request of 4 patches for net/master.
The first two patches are by Wang Xiayang, they force that the string buffer
during a dev_info() is properly NULL terminated.
The last two patches are by Tomas Bortoli and fix both a potential info leak of
kernel memory to USB devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
desc_cnt and data_cnt should always be equal. In the case of a dropped
packet desc_cnt was still getting updated (correctly), data_cnt
was not. To eliminate this bug and prevent it from recurring this
patch combines them into one ring level cnt.
Signed-off-by: Catherine Sullivan <csully@google.com>
Reviewed-by: Sagi Shahar <sagis@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 069d11465a ("net/mlx5e: RX, Enhance legacy Receive Queue
memory scheme") introduced an undefined behaviour below due to
"frag->last_in_page" is only initialized in mlx5e_init_frags_partition()
when,
if (next_frag.offset + frag_info[f].frag_stride > PAGE_SIZE)
or after bailed out the loop,
for (i = 0; i < mlx5_wq_cyc_get_size(&rq->wqe.wq); i++)
As the result, there could be some "frag" have uninitialized
value of "last_in_page".
Later, get_frag() obtains those "frag" and check "frag->last_in_page" in
mlx5e_put_rx_frag() and triggers the error during boot. Fix it by always
initializing "frag->last_in_page" to "false" in
mlx5e_init_frags_partition().
UBSAN: Undefined behaviour in
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:325:12
load of value 170 is not a valid value for type 'bool' (aka '_Bool')
Call trace:
dump_backtrace+0x0/0x264
show_stack+0x20/0x2c
dump_stack+0xb0/0x104
__ubsan_handle_load_invalid_value+0x104/0x128
mlx5e_handle_rx_cqe+0x8e8/0x12cc [mlx5_core]
mlx5e_poll_rx_cq+0xca8/0x1a94 [mlx5_core]
mlx5e_napi_poll+0x17c/0xa30 [mlx5_core]
net_rx_action+0x248/0x940
__do_softirq+0x350/0x7b8
irq_exit+0x200/0x26c
__handle_domain_irq+0xc8/0x128
gic_handle_irq+0x138/0x228
el1_irq+0xb8/0x140
arch_cpu_idle+0x1a4/0x348
do_idle+0x114/0x1b0
cpu_startup_entry+0x24/0x28
rest_init+0x1ac/0x1dc
arch_call_rest_init+0x10/0x18
start_kernel+0x4d4/0x57c
Fixes: 069d11465a ("net/mlx5e: RX, Enhance legacy Receive Queue memory scheme")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to drop the adjust_link callback in order to finally migrate to
phylink.
Otherwise we get the following warning during startup:
"mv88e6xxx 2188000.ethernet-1:10: Using legacy PHYLIB callbacks. Please
migrate to PHYLINK!"
The warning is generated in the function dsa_port_link_register_of in
dsa/port.c:
int dsa_port_link_register_of(struct dsa_port *dp)
{
struct dsa_switch *ds = dp->ds;
if (!ds->ops->adjust_link)
return dsa_port_phylink_register(dp);
dev_warn(ds->dev,
"Using legacy PHYLIB callbacks. Please migrate to PHYLINK!\n");
[...]
}
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is likely that PAL_BDC_CR should be PLA_BDC_CR.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like FSL_ENETC, when CONFIG_FSL_ENETC_VF is set,
we should select PHYLIB, otherwise building still fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c:(.text+0x2744): undefined reference to `phy_start'
enetc.c:(.text+0x282c): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c:(.text+0x28f8): undefined reference to `phy_stop'
enetc.c:(.text+0x2904): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x3f8): undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x400): undefined reference to `phy_ethtool_set_link_ksettings'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
strncpy() does not ensure NULL-termination when the input string
size equals to the destination buffer size 30.
The output string is passed to qed_int_deassertion_aeu_bit()
which calls DP_INFO() and relies NULL-termination.
Use strlcpy instead. The other conditional branch above strncpy()
needs no fix as snprintf() ensures NULL-termination.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com
Fixes: f14e22435a ("net: can: peak_usb: Do not do dma on the stack")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string is
passed to dev_info() which relies on the NULL-termination.
Use strlcpy() instead.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string
'name' is passed to dev_info which relies on NULL-termination.
Use strlcpy() instead.
This issue is identified by a Coccinelle script.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
get_registers() may fail with -ENOMEM and in this
case we can read a garbage from the status variable tmp.
Reported-by: syzbot+3499a83b2d062ae409d4@syzkaller.appspotmail.com
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The help text refers to AMD instead of Broadcom, presumably because it
was copied from the former.
Fixes: adfc5217e9 ("broadcom: Move the Broadcom drivers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The help text refers to IBM instead of Apple, presumably because it was
copied from the former.
Fixes: 8fb6b09081 ("bmac/mace/macmace/mac89x0/cs89x0: Move the Macintosh (Apple) drivers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The help text refers to Western Digital instead of National
Semiconductor 8390, presumably because it was copied from the former.
Fixes: 644570b830 ("8390: Move the 8390 related drivers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variant of netif_napi_add() should be used from drivers
using NAPI to exclusively poll a TX queue.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_led_trigger_change_speed(), there is an if statement on line 48
to check whether phy->last_triggered is NULL:
if (!phy->last_triggered)
When phy->last_triggered is NULL, it is used on line 52:
led_trigger_event(&phy->last_triggered->trigger, LED_OFF);
Thus, a possible null-pointer dereference may occur.
To fix this bug, led_trigger_event(&phy->last_triggered->trigger,
LED_OFF) is called when phy->last_triggered is not NULL.
This bug is found by a static analysis tool STCheck written by
the OSLAB group in Tsinghua University.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole block is protected by "if NET_VENDOR_MEDIATEK", so there is
no need for individual driver config symbols to duplicate this
dependency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
* revert NETIF_F_LLTX usage as it caused problems
* avoid warning on WMM parameters from AP that are too short
* fix possible null-ptr dereference in hwsim
* fix interface combinations with 4-addr and crypto control
-----BEGIN PGP SIGNATURE-----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=rE1e
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* revert NETIF_F_LLTX usage as it caused problems
* avoid warning on WMM parameters from AP that are too short
* fix possible null-ptr dereference in hwsim
* fix interface combinations with 4-addr and crypto control
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use GFP_ATOMIC here, GFP_KERNEL should be enough.
The 'kcalloc()' just a few lines above, already uses GFP_KERNEL.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to use GFP_ATOMIC here. Other memory allocations
are performed with GFP_KERNEL (see other 'dma_alloc_coherent()' below and
'kzalloc()' in 'et131x_rx_dma_memory_alloc()')
Use GFP_KERNEL which should be enough.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e891ce1dd2 ("mlxsw: spectrum_buffers: Reduce pool size on
Spectrum-2"), pool size was reduced to mitigate a problem in port buffer
usage of ports split four ways. It turns out that this work around does not
solve the issue, and a further reduction is required.
Thus reduce the size of pool 0 by another 2.7 MiB, and round down to the
whole number of cells.
Fixes: e891ce1dd2 ("mlxsw: spectrum_buffers: Reduce pool size on Spectrum-2")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of sp2 pci driver registration fail, fix the error path to
start with sp1 pci driver unregister.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notably:
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
-----BEGIN PGP SIGNATURE-----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=7W8I
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-fixes-for-kvalo-2019-07-30' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
We have a lot of fixes, most of them are also applicable to stable.
Notably:
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
Set phy device advertising to enable MAC flow control.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for handling the PPPOEIOCSFWD ioctl in compat mode was added in
linux-2.5.69 along with hundreds of other commands, but was always broken
sincen only the structure is compatible, but the command number is not,
due to the size being sizeof(size_t), or at first sizeof(sizeof((struct
sockaddr_pppox)), which is different on 64-bit architectures.
Guillaume Nault adds:
And the implementation was broken until 2016 (see 29e73269aa ("pppoe:
fix reference counting in PPPoE proxy")), and nobody ever noticed. I
should probably have removed this ioctl entirely instead of fixing it.
Clearly, it has never been used.
Fix it by adding a compat_ioctl handler for all pppoe variants that
translates the command number and then calls the regular ioctl function.
All other ioctl commands handled by pppoe are compatible between 32-bit
and 64-bit, and require compat_ptr() conversion.
This should apply to all stable kernels.
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PHYLIB is not set, build enetc will fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c: undefined reference to `phy_disconnect'
enetc.c: undefined reference to `phy_start'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c: undefined reference to `phy_stop'
enetc.c: undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_set_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_mdio.o: In function `enetc_mdio_probe':
enetc_mdio.c: undefined reference to `mdiobus_alloc_size'
enetc_mdio.c: undefined reference to `mdiobus_free'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent changes that introduced support for Page Pool in stmmac, Jon
reported that NFS boot was no longer working on an ARM64 based platform
that had the IP behind an IOMMU.
As Page Pool API does not guarantee DMA syncing because of the use of
DMA_ATTR_SKIP_CPU_SYNC flag, we have to explicit sync the whole buffer upon
re-allocation because we are always re-using same pages.
In fact, ARM64 code invalidates the DMA area upon two situations [1]:
- sync_single_for_cpu(): Invalidates if direction != DMA_TO_DEVICE
- sync_single_for_device(): Invalidates if direction == DMA_FROM_DEVICE
So, as we must invalidate both the current RX buffer and the newly allocated
buffer we propose this fix.
[1] arch/arm64/mm/cache.S
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 2af6106ae9 ("net: stmmac: Introducing support for Page Pool")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently are duplicated checks on orig_egr_types which are
redundant, I believe this is a typo and should actually be
orig_ing_types || orig_egr_types instead of the expression
orig_egr_types || orig_egr_types. Fix these.
Addresses-Coverity: ("Same on both sides")
Fixes: c6b36bdd04 ("mlxsw: spectrum_ptp: Increase parsing depth when PTP is enabled")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the define here makes the code more expressive.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.
Fixes: 5468e82f70 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()")
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing the hdr of an skb that was consumed already isn't
a good idea.
First ask if the skb is a QoS packet, then keep that data
on stack, and then consume the skb.
This was spotted by KASAN.
Cc: stable@vger.kernel.org
Fixes: 08f7d8b69a ("iwlwifi: mvm: bring back mvm GSO code")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The index for the elements of the ACPI object we dereference
was static. This means that if we called the function twice
we wouldn't start from 3 again, but rather from the latest
index we reached in the previous call.
This was dutifully reported by KASAN.
Fix this.
Cc: stable@vger.kernel.org
Fixes: 6996490501 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to remember how to unmap a memory (as single or
as page), we maintain a bit per Transmit Buffer (TBs) in
the meta data (structure iwl_cmd_meta).
We maintain a bitmap: 1 bit per TB.
If the TB is set, we will free the memory as a page.
This bitmap was never cleared. Fix this.
Cc: stable@vger.kernel.org
Fixes: 3cd1980b0c ("iwlwifi: pcie: introduce new tfd and tb formats")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We erroneously added a check for FW API version 41 before sending
GEO_TX_POWER_LIMIT, but this was already implemented in version 38.
Additionally, it was cherry-picked to older versions, namely 17, 26
and 29, so check for those as well.
Cc: stable@vger.kernel.org
Fixes: eca1e56cee ("iwlwifi: mvm: don't send GEO_TX_POWER_LIMIT to old firmwares")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a few PCI ID'S for 9000 series.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
lq_info is an arary of size 2, active_tbl index is u8.
When accessing lq_info[1 - active_tbl], theoretically it's possible
that the access will be made to a negative index value.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An earlier patch made sure that the queues are not lagging
too far behind. This means that iwl_mvm_release_frames
should not be called with a head_sn too far behind NSSN.
Don't take the risk to change completely the entry
condition to iwl_mvm_release_frames, but don't update
the head_sn is the NSSN is more than 2048 packets ahead
of us. Since this just cannot be right. This means that
the scenario described here happened. We are queue 0.
Q:0 Q:1
head_sn: 0 -> 2047
head_sn: 2048
Lots of packets arrive:
head_sn: 2047 -> 2150
send NSSN_SYNC notification
Handle notification
from the firmware and
do NOT move the head_sn
back to 2048
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The solution with the worker still had a bug, as in order
to get sta, rcu_read_lock should be used and thus no mutex
can be used inside iwl_mvm_rs_rate_init.
Also, spin_lock is a simpler solution, no need to spawn a
dedicated worker.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only place where the command was sent as SYNC is during
init and this is not really critical. This change is required
for replacing RS mutex with a spinlock (in the subsequent patch),
since SYNC comamnd requres sleeping and thus the flow cannot
be done when holding a spinlock.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comparison of the u32 variable wgds_tbl_idx with less than zero is
always going to be false because it is unsigned. Fix this by making
wgds_tbl_idx a plain signed int.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 4fd445a2c8 ("iwlwifi: mvm: Add log information about SAR status")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code clearly never could have worked, since it locks
while already locked. Add an unlocked __iwl_mvm_mac_set_key()
variant that doesn't do locking to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver should call iwl_dbg_tlv_free even if debugfs is not defined
since ini mode does not depend on debugfs ifdef.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 68f6f492c4 ("iwlwifi: trans: support loading ini TLVs from external file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ini debug mode should work even if debug override is not defined.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 68f6f492c4 ("iwlwifi: trans: support loading ini TLVs from external file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_rs_tx_status can be called from two places in the code, but the
mutex is taken only on one of the calls. Split it into a wrapper taking
locks and an internal __iwl_mvm_rs_tx_status function.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support MSI-X efficiently, we want to avoid
communication across Rx queues. Each Rx queue should have
all the data it needs to process a packet.
The reordering buffer is a challenge in the MSI-X world
since we can have a single BA session whose packets are
directed to different queues. This is why each queue has
its own reordering buffer. The hardware is able to hint
the driver whether we have a hole or not, which allows
the driver to know whether it can release a packet or not.
This indication is called NSSN. Roughly, if the packet's
SN is lower than the NSSN, we can release the packet to
the stack. The NSSN is the SN of the newest packet received
without any holes + 1.
This is working as long as we don't have packets that we
release because of a timeout. When that happens, we could
have taken the decision to release a packet after we have
been waiting for its predecessor for too long. If this
predecessor comes later, we have to drop it because we
can't release packets out of order. In that case, the
hardware will give us an indication that we can we release
the packet (SN < NSSN), but the packet still needs to be
dropped.
This is why we sometimes need to ignore the NSSN and we
track the head_sn in software.
Here is a specific example of this:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480
6) 481 arrives its NSSN is 484.
We need to drop 481 even if 481 < 484. This is why we'll
update the head_sn to 484 at step 2. The flow now is:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481 / head_sn is 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480 but head_sn is 484.
6) 481 arrives its NSSN is 484, but head_sn is 484 and we drop it.
This code introduces another problem in case all the traffic
goes well (no hole, no timeout):
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 4095 (head_sn = 0)
Rx queue 2: 0 -> 480 (head_sn = 481)
Rx queue 1: 481 but head_sn = 484 and we drop it.
At this point, the SN of queue 1 is far behind: more than
4040 packets behind. Queue 1 will consider 481 "old"
because 481 is in [501-64:501] whereas it is a very new
packet.
In order to fix that, send an Rx notification from time to
time (twice across the full set of 4096 packets) to make
sure no Rx queue is lagging too far behind.
What will happen then is:
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 2047 (head_sn = 2048)
Rx queue 1: Sync nofication (head_sn = 2048)
Rx queue 2: 2048 -> 4095 (head_sn = 0)
Rx queue 1: Sync notification (head_sn = 0)
Rx queue 2: 1 -> 481 (head_sn = 482)
Rx queue 1: 481 and head_sn = 0.
In queue 1's data, head_sn is now 0, the packet coming in
is 481, it'll understand that the new packet is new and it
won't be dropped.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of allocating memory for which we have an upper
limit, use a small buffer on stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will soon be using a new notification that will be
initiated by the driver, sent to the firmware and sent
back to all the RSS queues by the firmware. This new
notification will be useful to synchronize the NSSN across
all the queues.
For now, don't send the notification, just add the code to
handle it. Later patch will add the code to actually send
it.
While at it, validate the baid coming from the firmware to
avoid accessing an array with a bad index in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will need a new type of synchronization message going
through all the RSS queues. Prepare the ground for this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware versions before 41 don't support the GEO_TX_POWER_LIMIT
command, and sending it to the firmware will cause a firmware crash.
We allow this via debugfs, so we need to return an error value in case
it's not supported.
This had already been fixed during init, when we send the command if
the ACPI WGDS table is present. Fix it also for the other,
userspace-triggered case.
Cc: stable@vger.kernel.org
Fixes: 7fe90e0e3d ("iwlwifi: mvm: refactor geo init")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rate perform uses the lq_sta table to calculate the next rate to scale
while rate init resets the same table,
Rate perform is done in soft irq context in parallel to rate init
that can be called in case we are doing changes like AP changes BW
or moving state for auth to assoc.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On older NICs, we occasionally see issues with A-MSDU support,
where the commands in the FIFO get confused and then we see an
assert EDC because the next command in the FIFO isn't TX.
We've tried to isolate this issue and understand where it comes
from, but haven't found any errors in building the A-MSDU in
software.
At least for now, disable A-MSDU support on older hardware so
that users can use it again without fearing the assert.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=203315.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 63d7ef3610 ("mwifiex: Don't abort on small, spec-compliant
vendor IEs") adjusted the ieee_types_vendor_header struct, which
inadvertently messed up the offsets used in
mwifiex_is_wpa_oui_present(). Add that offset back in, mirroring
mwifiex_is_rsn_oui_present().
As it stands, commit 63d7ef3610 breaks compatibility with WPA (not
WPA2) 802.11n networks, since we hit the "info: Disable 11n if AES is
not supported by AP" case in mwifiex_is_network_compatible().
Fixes: 63d7ef3610 ("mwifiex: Don't abort on small, spec-compliant vendor IEs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/net/ethernet/smsc/smc911x.c: In function ‘smc911x_phy_detect’:
drivers/net/ethernet/smsc/smc911x.c:677:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (cfg & HW_CFG_EXT_PHY_DET_) {
^
drivers/net/ethernet/smsc/smc911x.c:715:3: note: here
default:
^~~~~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: i386):
drivers/net/hamradio/baycom_epp.c: In function ‘transmit’:
drivers/net/hamradio/baycom_epp.c:491:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (i) {
^
drivers/net/hamradio/baycom_epp.c:504:3: note: here
default: /* fall through */
^~~~~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: i386):
drivers/net/wan/sdla.c: In function ‘sdla_errors’:
drivers/net/wan/sdla.c:414:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (cmd == SDLA_INFORMATION_WRITE)
^
drivers/net/wan/sdla.c:417:3: note: here
default:
^~~~~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum systems have a configurable limit on how far into the packet they
parse. By default, the limit is 96 bytes.
An IPv6 PTP packet is layered as Ethernet/IPv6/UDP (14+40+8 bytes), and
sequence ID of a PTP event is only available 32 bytes into payload, for a
total of 94 bytes. When an additional 802.1q header is present as
well (such as when ptp4l is running on a VLAN port), the parsing limit is
exceeded. Such packets are not recognized as PTP, and are not timestamped.
Therefore generalize the current VXLAN-specific parsing depth setting to
allow reference-counted requests from other modules as well. Keep it in the
VXLAN module, because the MPRS register also configures UDP destination
port number used for VXLAN, and is thus closely tied to the VXLAN code
anyway.
Then invoke the new interfaces from both VXLAN (in obvious places), as well
as from PTP code, when the (global) timestamping configuration changes from
disabled to enabled or vice versa.
Fixes: 8748642751 ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/toshiba/spider_net.c: In function 'spider_net_release_tx_chain':
drivers/net/ethernet/toshiba/spider_net.c:783:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!brutal) {
^
drivers/net/ethernet/toshiba/spider_net.c:792:3: note: here
case SPIDER_NET_DESCR_RESPONSE_ERROR:
^~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/ibm/ehea/ehea_main.c: In function 'ehea_mem_notifier':
include/linux/printk.h:311:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_INFO pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ibm/ehea/ehea_main.c:3253:3: note: in expansion of macro 'pr_info'
pr_info("memory offlining canceled");
^~~~~~~
drivers/net/ethernet/ibm/ehea/ehea_main.c:3256:2: note: here
case MEM_ONLINE:
^~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can only offload checksum calculation on first port due to
the Tx FIFO size limitation, and has a maximum L3 offset of 128 bytes.
Document this in a comment and move duplicated code in a function.
Fixes: 576193f2d5 ("net: mvpp2: jumbo frames support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU change code can call napi_disable() with the device already down,
leading to a deadlock. Also, lot of code is duplicated unnecessarily.
Rework mvpp2_change_mtu() to avoid the deadlock and remove duplicated code.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two error return paths that leak memory allocated
to fib_work. Fix this by kfree'ing fib_work before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 19a9d136f1 ("ipv4: Flag fib_info with a fib_nh using IPv6 gateway")
Fixes: dbcc4fa718 ("rocker: Fail attempts to use routes with nexthop objects")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
added support for reading the MAC address from an nvmem-cell. This
required changing the logic to return an error pointer upon failure.
If stmmac is loaded before the nvmem provider driver then
of_get_mac_address() return an error pointer with -EPROBE_DEFER.
Propagate this error so the stmmac driver will be probed again after the
nvmem provider driver is loaded.
Default to a random generated MAC address in case of any other error,
instead of using the error pointer as MAC address.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/arcnet/com20020-isa.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 205:13, 203:10, 209:7, 201:11,
207:8
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: powerpc allyesconfig):
drivers/net/arcnet/arc-rimi.c: In function 'arcrimi_setup':
include/linux/printk.h:304:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/arcnet/arc-rimi.c:365:3: note: in expansion of macro 'pr_err'
pr_err("Too many arguments\n");
^~~~~~
drivers/net/arcnet/arc-rimi.c:366:2: note: here
case 3: /* Node ID */
^~~~
drivers/net/arcnet/arc-rimi.c:367:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
node = ints[3];
~~~~~^~~~~~~~~
drivers/net/arcnet/arc-rimi.c:368:2: note: here
case 2: /* IRQ */
^~~~
drivers/net/arcnet/arc-rimi.c:369:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
irq = ints[2];
~~~~^~~~~~~~~
drivers/net/arcnet/arc-rimi.c:370:2: note: here
case 1: /* IO address */
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: powerpc allyesconfig):
drivers/net/arcnet/com90io.c: In function 'com90io_setup':
include/linux/printk.h:304:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/arcnet/com90io.c:365:3: note: in expansion of macro 'pr_err'
pr_err("Too many arguments\n");
^~~~~~
drivers/net/arcnet/com90io.c:366:2: note: here
case 2: /* IRQ */
^~~~
drivers/net/arcnet/com90io.c:367:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
irq = ints[2];
~~~~^~~~~~~~~
drivers/net/arcnet/com90io.c:368:2: note: here
case 1: /* IO address */
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: powerpc allyesconfig):
drivers/net/arcnet/com90xx.c: In function 'com90xx_setup':
include/linux/printk.h:304:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/arcnet/com90xx.c:695:3: note: in expansion of macro 'pr_err'
pr_err("Too many arguments\n");
^~~~~~
drivers/net/arcnet/com90xx.c:696:2: note: here
case 3: /* Mem address */
^~~~
drivers/net/arcnet/com90xx.c:697:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
shmem = ints[3];
~~~~~~^~~~~~~~~
drivers/net/arcnet/com90xx.c:698:2: note: here
case 2: /* IRQ */
^~~~
drivers/net/arcnet/com90xx.c:699:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
irq = ints[2];
~~~~^~~~~~~~~
drivers/net/arcnet/com90xx.c:700:2: note: here
case 1: /* IO address */
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hwsim_dump_radio_nl(), when genlmsg_put() on line 3617 fails, hdr is
assigned to NULL. Then hdr is used on lines 3622 and 3623:
genl_dump_check_consistent(cb, hdr);
genlmsg_end(skb, hdr);
Thus, possible null-pointer dereferences may occur.
To fix these bugs, hdr is used here when it is not NULL.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20190729082332.28895-1-baijiaju1990@gmail.com
[put braces on all branches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was reported that after resuming from suspend network fails with
error "do_IRQ: 3.38 No irq handler for vector", see [0]. Enabling WoL
can work around the issue, but the only actual fix is to disable MSI.
So let's mimic the behavior of the vendor driver and disable MSI on
all chip versions before RTL8168d.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=204079
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Reported-by: Dušan Dragić <dragic.dusan@gmail.com>
Tested-by: Dušan Dragić <dragic.dusan@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a6851c613f.
It was reported that RTL8111b successfully finishes 1000/Full autoneg
but no data flows. Reverting the original patch fixes the issue.
It seems to be a HW issue with the integrated RTL8211B PHY. This PHY
version used also e.g. on RTL8168d, so better revert the original patch.
Reported-by: Bernhard Held <berny156@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through. These patches are part of the ongoing efforts
to enable -Wimplicit-fallthrough. Most of them have been baking in linux-next
for a whole development cycle.
Also, pull the Makefile patch that globally enables the
-Wimplicit-fallthrough option.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
Notice that with these changes, we completely get rid of all the
fall-through warnings in the kernel.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEkmRahXBSurMIg1YvRwW0y0cG2zEFAl06XP0ACgkQRwW0y0cG
2zHPXhAAsatJGNIg7vuSicVipJBIlwgRLwtbE2rV+MCneUAZj37O9NtBgbxHNoJ+
5TBB8sLpNCw3rEvPKwm6vicRgntMclEY1vaplPOHt3RiY4lqVSIkpvFSCw1hGur3
+34+O++n/6HbtY96T+DN5WGMXrU3JSe46xnBLIt0BOoUwyKMaNdntiyd79GrrnyB
BwPkHrmB+9FEVq+dHmPnRIhc9WUfIdily3+j1CIncaM4eXKWLjoUlOIw1VcSEc4X
SSdFh2co+3nm/6O54ZxUEC1PyuQZWedsgFmeiTrOanG3AEWQ/jX7GwXvPlgraa2E
F5MzGUOQwXYL/IzXl1vGjQc4+FV4nhIjEBTDdZseOp7FP5xkHyyOwzGDEmaMXpXT
XThb+k7Q6EbiSPLFcz8zkCwNB8ngNJMNOsGP3JPFD06MfquqdzP7T1BsHcNtiMVo
FNwQg9KtvbK9F7a9lXDqfcxfuEScbqSvnKWWwNLImCqIBATYirJzeTeLvTbVWpA2
iyXF3ylIclsSMOvCtaz41iuoqNh12eqw2UIFPBmkU2wpVkTt+ZIn0Apgom90xe1K
tSUqMBbBMoHVtsBsILdkdz/m6FJpK+YmmwpRrJSDvPxA5c9caD7cj+62amW/gP4z
Hi6mC4hw1H5bKMsC2PP/QgJcmS/pgo1zwA9J2a2NNJbYPATHfKI=
=J2sO
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull Wimplicit-fallthrough enablement from Gustavo A. R. Silva:
"This marks switch cases where we are expecting to fall through, and
globally enables the -Wimplicit-fallthrough option in the main
Makefile.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
With these changes, we completely get rid of all the fall-through
warnings in the kernel"
* tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
Makefile: Globally enable fall-through warning
drm/i915: Mark expected switch fall-throughs
drm/amd/display: Mark expected switch fall-throughs
drm/amdkfd/kfd_mqd_manager_v10: Avoid fall-through warning
drm/amdgpu/gfx10: Fix missing break in switch statement
drm/amdkfd: Fix missing break in switch statement
perf/x86/intel: Mark expected switch fall-throughs
mtd: onenand_base: Mark expected switch fall-through
afs: fsclient: Mark expected switch fall-throughs
afs: yfsclient: Mark expected switch fall-throughs
can: mark expected switch fall-throughs
firewire: mark expected switch fall-throughs
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl06EYUACgkQSD+KveBX
+j7R4QgAht/C4115mi1Tc3d3zYjHp3SWLFxwK4vF0U2j30ouhsj1oaIP8bQdw6Mr
6hS4IZSdKNO5wo+NNqMnLYVtsAnvNGOuvYwUvMK5TDkdDb2lIzRlxihpWgTqWzXr
6Eh3nv5rTItgLMqxbLL1EE8Idlx3HQDJtU2a/AmxjmU/TqSKzbBTpnKIlRMPDFNC
PLWXjFXBR/XtcTbsnj7RtlD2HkDAERVTiMP2mlTvXjXxlN56YXCle4CWZamgH9H4
bTCrZwQHH9hllMAnAkq4gpHN7Z6/eXjV6jzu+BOE7ChOaEC5N2F+p5ARXqe+HwRL
apMYgRH5u4mzDt+1CbwR/I/pFOw3WA==
=NXce
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-07-25
This series introduces some fixes to mlx5 driver.
1) Ariel is addressing an issue with enacp flow counter race condition
2) Aya fixes ethtool speed handling
3) Edward fixes modify_cq hw bits alignment
4) Maor fixes RDMA_RX capabilities handling
5) Mark reverses unregister devices order to address an issue with LAG
6) From Tariq,
- wrong max num channels indication regression
- TLS counters naming and documentation as suggested by Jakub
- kTLS, Call WARN_ONCE on netdev mismatch
There is one patch in this series that touches nfp driver to align
TLS statistics names with latest documentation, Jakub is CC'ed.
Please pull and let me know if there is any problem.
For -stable v4.9:
('net/mlx5: Use reversed order when unregister devices')
For -stable v4.20
('net/mlx5e: Prevent encap flow counter update async to user query')
('net/mlx5: Fix modify_cq_in alignment')
For -stable v5.1
('net/mlx5e: Fix matching of speed to PRM link modes')
For -stable v5.2
('net/mlx5: Add missing RDMA_RX capabilities')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.
However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.
In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.
Fixes: 5eb5f8608e ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the delayed work for stats update is not pending before
wq destruction.
This fixes the module unload path.
The issue is there since day 1.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hw_ver field was initialized to zero. Return the chip revision.
This is relevant for rdma driver.
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BroadMobi BM818 M.2 card uses the QMI protocol
Signed-off-by: Bob Ham <bob.ham@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (n & PCAN_USB_ERROR_BUS_LIGHT) {
^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
case CAN_STATE_ERROR_WARNING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Commit 3968d38917 ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.
Fixes: 3968d38917 ("bnx2x: Fix Multi-Cos.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean
Nishka Dasgupta
Jiangfeng Xiao
Jose Abreu
David S. Miller
Denis Kirjanov
Christophe JAILLET
Chen-Yu Tsai
Arnaud Patard (Rtp)
Catherine Sullivan
Qian Cai
Hubert Feurstein
Kevin Lo
Heiner Kallweit
YueHaibing
Wang Xiayang
Tomas Bortoli
Geert Uytterhoeven
Matteo Croce
Mauro Rossi
Frode Isaksen
Jia-Ju Bai
Petr Machata
Jiri Pirko
Kalle Valo
xiaofeis
Arnd Bergmann
Colin Ian King
Emmanuel Grumbach
Luca Coelho
Ihab Zhaika
Gregory Greenman
Johannes Berg
Shahar S Matityahu
Mordechay Goodstein
Brian Norris
Gustavo A. R. Silva
Martin Blumenstingl
René van Dorst
Linus Torvalds
Subash Abhinov Kasiviswanathan
Claudiu Manoil
Michal Kalderon
Bob Ham
Sudarsana Reddy Kalluru