The hypervisor can enable various new features (SEV_FEATURES[1:63]) and start a
SNP guest. Some of these features need guest side implementation. If any of
these features are enabled without it, the behavior of the SNP guest will be
undefined. It may fail booting in a non-obvious way making it difficult to
debug.
Instead of allowing the guest to continue and have it fail randomly later,
detect this early and fail gracefully.
The SEV_STATUS MSR indicates features which the hypervisor has enabled. While
booting, SNP guests should ascertain that all the enabled features have guest
side implementation. In case a feature is not implemented in the guest, the
guest terminates booting with GHCB protocol Non-Automatic Exit(NAE) termination
request event, see "SEV-ES Guest-Hypervisor Communication Block Standardization"
document (currently at https://developer.amd.com/wp-content/resources/56421.pdf),
section "Termination Request".
Populate SW_EXITINFO2 with mask of unsupported features that the hypervisor can
easily report to the user.
More details in the AMD64 APM Vol 2, Section "SEV_STATUS MSR".
[ bp:
- Massage.
- Move snp_check_features() call to C code.
Note: the CC:stable@ aspect here is to be able to protect older, stable
kernels when running on newer hypervisors. Or not "running" but fail
reliably and in a well-defined manner instead of randomly. ]
Fixes: cbd3d4f7c4 ("x86/sev: Check SEV-SNP features support")
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20230118061943.534309-1-nikunj@amd.com
In some cases, bootloaders will leave boot_params->cc_blob_address
uninitialized rather than zeroing it out. This field is only meant to be
set by the boot/compressed kernel in order to pass information to the
uncompressed kernel when SEV-SNP support is enabled.
Therefore, there are no cases where the bootloader-provided values
should be treated as anything other than garbage. Otherwise, the
uncompressed kernel may attempt to access this bogus address, leading to
a crash during early boot.
Normally, sanitize_boot_params() would be used to clear out such fields
but that happens too late: sev_enable() may have already initialized
it to a valid value that should not be zeroed out. Instead, have
sev_enable() zero it out unconditionally beforehand.
Also ensure this happens for !CONFIG_AMD_MEM_ENCRYPT as well by also
including this handling in the sev_enable() stub function.
[ bp: Massage commit message and comments. ]
Fixes: b190a043c4 ("x86/sev: Add SEV-SNP feature detection/setup")
Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reported-by: watnuss@gmx.de
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216387
Link: https://lore.kernel.org/r/20220823160734.89036-1-michael.roth@amd.com
SEV-SNP guests will be provided the location of special 'secrets' and
'CPUID' pages via the Confidential Computing blob. This blob is
provided to the run-time kernel either through a boot_params field that
was initialized by the boot/compressed kernel, or via a setup_data
structure as defined by the Linux Boot Protocol.
Locate the Confidential Computing blob from these sources and, if found,
use the provided CPUID page/table address to create a copy that the
run-time kernel will use when servicing CPUID instructions via a #VC
handler.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-40-brijesh.singh@amd.com
Initial/preliminary detection of SEV-SNP is done via the Confidential
Computing blob. Check for it prior to the normal SEV/SME feature
initialization, and add some sanity checks to confirm it agrees with
SEV-SNP CPUID/MSR bits.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-39-brijesh.singh@amd.com
The run-time kernel will need to access the Confidential Computing blob
very early during boot to access the CPUID table it points to. At that
stage, it will be relying on the identity-mapped page table set up by
the boot/compressed kernel, so make sure the blob and the CPUID table it
points to are mapped in advance.
[ bp: Massage. ]
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-38-brijesh.singh@amd.com
SEV-SNP guests will be provided the location of special 'secrets'
'CPUID' pages via the Confidential Computing blob. This blob is
provided to the boot kernel either through an EFI config table entry,
or via a setup_data structure as defined by the Linux Boot Protocol.
Locate the Confidential Computing from these sources and, if found,
use the provided CPUID page/table address to create a copy that the
boot kernel will use when servicing CPUID instructions via a #VC CPUID
handler.
[ bp: s/cpuid/CPUID/ ]
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-36-brijesh.singh@amd.com
Initial/preliminary detection of SEV-SNP is done via the Confidential
Computing blob. Check for it prior to the normal SEV/SME feature
initialization, and add some sanity checks to confirm it agrees with
SEV-SNP CPUID/MSR bits.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-35-brijesh.singh@amd.com
This code will also be used later for SEV-SNP-validated CPUID code in
some cases, so move it to a common helper.
While here, also add a check to terminate in cases where the CPUID
function/subfunction is indexed and the subfunction is non-zero, since
the GHCB MSR protocol does not support non-zero subfunctions.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-32-brijesh.singh@amd.com
The SEV-SNP guest is required by the GHCB spec to register the GHCB's
Guest Physical Address (GPA). This is because the hypervisor may prefer
that a guest use a consistent and/or specific GPA for the GHCB associated
with a vCPU. For more information, see the GHCB specification section
"GHCB GPA Registration".
If hypervisor can not work with the guest provided GPA then terminate the
guest boot.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Venu Busireddy <venu.busireddy@oracle.com>
Link: https://lore.kernel.org/r/20220307213356.2797205-17-brijesh.singh@amd.com
Many of the integrity guarantees of SEV-SNP are enforced through the
Reverse Map Table (RMP). Each RMP entry contains the GPA at which a
particular page of DRAM should be mapped. The VMs can request the
hypervisor to add pages in the RMP table via the Page State Change
VMGEXIT defined in the GHCB specification.
Inside each RMP entry is a Validated flag; this flag is automatically
cleared to 0 by the CPU hardware when a new RMP entry is created for a
guest. Each VM page can be either validated or invalidated, as indicated
by the Validated flag in the RMP entry. Memory access to a private page
that is not validated generates a #VC. A VM must use the PVALIDATE
instruction to validate a private page before using it.
To maintain the security guarantee of SEV-SNP guests, when transitioning
pages from private to shared, the guest must invalidate the pages before
asking the hypervisor to change the page state to shared in the RMP table.
After the pages are mapped private in the page table, the guest must
issue a page state change VMGEXIT to mark the pages private in the RMP
table and validate them.
Upon boot, BIOS should have validated the entire system memory.
During the kernel decompression stage, early_setup_ghcb() uses
set_page_decrypted() to make the GHCB page shared (i.e. clear encryption
attribute). And while exiting from the decompression, it calls
set_page_encrypted() to make the page private.
Add snp_set_page_{private,shared}() helpers that are used by
set_page_{decrypted,encrypted}() to change the page state in the RMP
table.
[ bp: Massage commit message and comments. ]
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-16-brijesh.singh@amd.com
The Virtual Machine Privilege Level (VMPL) feature in the SEV-SNP
architecture allows a guest VM to divide its address space into four
levels. The level can be used to provide hardware isolated abstraction
layers within a VM. VMPL0 is the highest privilege level, and VMPL3 is
the least privilege level. Certain operations must be done by the VMPL0
software, such as:
* Validate or invalidate memory range (PVALIDATE instruction)
* Allocate VMSA page (RMPADJUST instruction when VMSA=1)
The initial SNP support requires that the guest kernel is running at
VMPL0. Add such a check to verify the guest is running at level 0 before
continuing the boot. There is no easy method to query the current VMPL
level, so use the RMPADJUST instruction to determine whether the guest
is running at the VMPL0.
[ bp: Massage commit message. ]
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-15-brijesh.singh@amd.com
Version 2 of the GHCB specification added the advertisement of features
that are supported by the hypervisor. If the hypervisor supports SEV-SNP
then it must set the SEV-SNP features bit to indicate that the base
functionality is supported.
Check that feature bit while establishing the GHCB; if failed, terminate
the guest.
Version 2 of the GHCB specification adds several new Non-Automatic Exits
(NAEs), most of them are optional except the hypervisor feature. Now
that the hypervisor feature NAE is implemented, bump the GHCB maximum
supported protocol version.
While at it, move the GHCB protocol negotiation check from the #VC
exception handler to sev_enable() so that all feature detection happens
before the first #VC exception.
While at it, document why the GHCB page cannot be setup from
load_stage2_idt().
[ bp: Massage commit message. ]
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-13-brijesh.singh@amd.com
The GHCB specification defines the reason code for reason set 0. The
reason codes defined in the set 0 do not cover all possible causes for a
guest to request termination.
The reason sets 1 to 255 are reserved for the vendor-specific codes.
Reserve the reason set 1 for the Linux guest. Define the error codes for
reason set 1 so that one can have meaningful termination reasons and thus
better guest failure diagnosis.
While at it, change sev_es_terminate() to accept a reason set parameter.
[ bp: Massage commit message. ]
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Venu Busireddy <venu.busireddy@oracle.com>
Link: https://lore.kernel.org/r/20220307213356.2797205-11-brijesh.singh@amd.com
With upcoming SEV-SNP support, SEV-related features need to be
initialized earlier during boot, at the same point the initial #VC
handler is set up, so that the SEV-SNP CPUID table can be utilized
during the initial feature checks. Also, SEV-SNP feature detection
will rely on EFI helper functions to scan the EFI config table for the
Confidential Computing blob, and so would need to be implemented at
least partially in C.
Currently set_sev_encryption_mask() is used to initialize the
sev_status and sme_me_mask globals that advertise what SEV/SME features
are available in a guest. Rename it to sev_enable() to better reflect
that (SME is only enabled in the case of SEV guests in the
boot/compressed kernel), and move it to just after the stage1 #VC
handler is set up so that it can be used to initialize SEV-SNP as well
in future patches.
While at it, re-implement it as C code so that all SEV feature
detection can be better consolidated with upcoming SEV-SNP feature
detection, which will also be in C.
The 32-bit entry path remains unchanged, as it never relied on the
set_sev_encryption_mask() initialization to begin with.
[ bp: Massage commit message. ]
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-8-brijesh.singh@amd.com
Update all C code to use the new boot_rdmsr()/boot_wrmsr() helpers
instead of relying on inline assembly.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220307213356.2797205-7-brijesh.singh@amd.com
SEV-SNP builds upon the SEV-ES functionality while adding new hardware
protection. Version 2 of the GHCB specification adds new NAE events that
are SEV-SNP specific. Rename the sev-es.{ch} to sev.{ch} so that all
SEV* functionality can be consolidated in one place.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20210427111636.1207-2-brijesh.singh@amd.com
Nikunj A Dadhania
Michael Roth
Brijesh Singh