CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
bfe4c041 "leds: convert Renesas TPU LED driver to devm_kzalloc() and
cleanup error exit path" introduced a possible case in which r_tpu_probe
calls iounmap on a wild pointer. This changes the one case that was
missed in the same way as the other error paths.
Without this patch, building kota2_defconfig results in:
drivers/leds/leds-renesas-tpu.c: In function 'r_tpu_probe':
drivers/leds/leds-renesas-tpu.c:246:6: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-renesas-tpu.c:308:17: warning: 'p' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Factor out some boilerplate code for platform driver registration into
module_platform_driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <hzhuang1@marvell.com> [led-88pm860x.c]
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Michael Hennerich <hennerich@blackfin.uclinux.org>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the platform_data include directory for the TPU LED driver, as
suggested by Paul Mundt.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use a workqueue in the Renesas TPU LED driver to allow the Runtime PM code
to sleep.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.
The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.
Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.
The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control. Hardware blink is unsupported.
The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board. Tested with experimental sh7372 A3SP power domain
patches. Platform device bind/unbind tested ok.
V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.
[axel.lin@gmail.com: include linux/module.h]
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds
Bill Pemberton
Jingoo Han
Arnd Bergmann
Bryan Wu
Axel Lin
Magnus Damm