If there are no channels defined in the devicetree, there's no point in
probing the device. We were actually requesting a zero sized 'kmalloc'
array but since we were not touching the ZERO_SIZE_PTR afterwards,
nothing bad was actually happening. Hence this is not really a fix but
rather an improvement.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210825084149.11587-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no reason to assume that the IRQ rising edge (indicating that
the device start up phase is done) will happen after we request the IRQ.
If the device is already up by the time we request it, the call to
'wait_for_completion_timeout()' will timeout and we will fail the device
probe even though there's nothing wrong.
Fix it by just polling the status register until we get the indication that
the device is up and running. As a side effect of this fix, requesting the
IRQ is also moved to after the setup function.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Reported-and-tested-by: Drew Fustini <drew@pdp7.com>
Reviewed-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210811133220.190264-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When returning or breaking early from a
`for_each_available_child_of_node()` loop, we need to explicitly call
`of_node_put()` on the child node to possibly release the node.
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200925091045.302-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;
It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'
But this is is only done in case where the block is left empty.
The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.
However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the read of temp using of_property_read_u32_index is reading
a u32 value into a unsigned long long. This relies on machine endianness
to work correctly, so fix this by reading a u32 value and setting temp
to this value.
Addresses-Coverity: ("Reliance on integer endianness")
Fixes: f110f3188e ("iio: temperature: Add support for LTC2983")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature
Measurement System. It measures a wide variety of temperature sensors and
digitally outputs the result, in °C or °F, with 0.1°C accuracy and
0.001°C resolution. It can measure the temperature of all standard
thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs,
thermistors and diodes.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nuno Sá
Alexandru Ardelean
Rohit Sarkar
Colin Ian King